t4_hw.c revision 331769
1/*- 2 * Copyright (c) 2012, 2016 Chelsio Communications, Inc. 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 14 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 15 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 16 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 17 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 18 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 19 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 20 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 21 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 22 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 23 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 24 * SUCH DAMAGE. 25 */ 26 27#include <sys/cdefs.h> 28__FBSDID("$FreeBSD: stable/11/sys/dev/cxgbe/common/t4_hw.c 331769 2018-03-30 18:06:29Z hselasky $"); 29 30#include "opt_inet.h" 31 32#include <sys/param.h> 33#include <sys/eventhandler.h> 34 35#include "common.h" 36#include "t4_regs.h" 37#include "t4_regs_values.h" 38#include "firmware/t4fw_interface.h" 39 40#undef msleep 41#define msleep(x) do { \ 42 if (cold) \ 43 DELAY((x) * 1000); \ 44 else \ 45 pause("t4hw", (x) * hz / 1000); \ 46} while (0) 47 48/** 49 * t4_wait_op_done_val - wait until an operation is completed 50 * @adapter: the adapter performing the operation 51 * @reg: the register to check for completion 52 * @mask: a single-bit field within @reg that indicates completion 53 * @polarity: the value of the field when the operation is completed 54 * @attempts: number of check iterations 55 * @delay: delay in usecs between iterations 56 * @valp: where to store the value of the register at completion time 57 * 58 * Wait until an operation is completed by checking a bit in a register 59 * up to @attempts times. If @valp is not NULL the value of the register 60 * at the time it indicated completion is stored there. Returns 0 if the 61 * operation completes and -EAGAIN otherwise. 62 */ 63static int t4_wait_op_done_val(struct adapter *adapter, int reg, u32 mask, 64 int polarity, int attempts, int delay, u32 *valp) 65{ 66 while (1) { 67 u32 val = t4_read_reg(adapter, reg); 68 69 if (!!(val & mask) == polarity) { 70 if (valp) 71 *valp = val; 72 return 0; 73 } 74 if (--attempts == 0) 75 return -EAGAIN; 76 if (delay) 77 udelay(delay); 78 } 79} 80 81static inline int t4_wait_op_done(struct adapter *adapter, int reg, u32 mask, 82 int polarity, int attempts, int delay) 83{ 84 return t4_wait_op_done_val(adapter, reg, mask, polarity, attempts, 85 delay, NULL); 86} 87 88/** 89 * t4_set_reg_field - set a register field to a value 90 * @adapter: the adapter to program 91 * @addr: the register address 92 * @mask: specifies the portion of the register to modify 93 * @val: the new value for the register field 94 * 95 * Sets a register field specified by the supplied mask to the 96 * given value. 97 */ 98void t4_set_reg_field(struct adapter *adapter, unsigned int addr, u32 mask, 99 u32 val) 100{ 101 u32 v = t4_read_reg(adapter, addr) & ~mask; 102 103 t4_write_reg(adapter, addr, v | val); 104 (void) t4_read_reg(adapter, addr); /* flush */ 105} 106 107/** 108 * t4_read_indirect - read indirectly addressed registers 109 * @adap: the adapter 110 * @addr_reg: register holding the indirect address 111 * @data_reg: register holding the value of the indirect register 112 * @vals: where the read register values are stored 113 * @nregs: how many indirect registers to read 114 * @start_idx: index of first indirect register to read 115 * 116 * Reads registers that are accessed indirectly through an address/data 117 * register pair. 118 */ 119void t4_read_indirect(struct adapter *adap, unsigned int addr_reg, 120 unsigned int data_reg, u32 *vals, 121 unsigned int nregs, unsigned int start_idx) 122{ 123 while (nregs--) { 124 t4_write_reg(adap, addr_reg, start_idx); 125 *vals++ = t4_read_reg(adap, data_reg); 126 start_idx++; 127 } 128} 129 130/** 131 * t4_write_indirect - write indirectly addressed registers 132 * @adap: the adapter 133 * @addr_reg: register holding the indirect addresses 134 * @data_reg: register holding the value for the indirect registers 135 * @vals: values to write 136 * @nregs: how many indirect registers to write 137 * @start_idx: address of first indirect register to write 138 * 139 * Writes a sequential block of registers that are accessed indirectly 140 * through an address/data register pair. 141 */ 142void t4_write_indirect(struct adapter *adap, unsigned int addr_reg, 143 unsigned int data_reg, const u32 *vals, 144 unsigned int nregs, unsigned int start_idx) 145{ 146 while (nregs--) { 147 t4_write_reg(adap, addr_reg, start_idx++); 148 t4_write_reg(adap, data_reg, *vals++); 149 } 150} 151 152/* 153 * Read a 32-bit PCI Configuration Space register via the PCI-E backdoor 154 * mechanism. This guarantees that we get the real value even if we're 155 * operating within a Virtual Machine and the Hypervisor is trapping our 156 * Configuration Space accesses. 157 * 158 * N.B. This routine should only be used as a last resort: the firmware uses 159 * the backdoor registers on a regular basis and we can end up 160 * conflicting with it's uses! 161 */ 162u32 t4_hw_pci_read_cfg4(adapter_t *adap, int reg) 163{ 164 u32 req = V_FUNCTION(adap->pf) | V_REGISTER(reg); 165 u32 val; 166 167 if (chip_id(adap) <= CHELSIO_T5) 168 req |= F_ENABLE; 169 else 170 req |= F_T6_ENABLE; 171 172 if (is_t4(adap)) 173 req |= F_LOCALCFG; 174 175 t4_write_reg(adap, A_PCIE_CFG_SPACE_REQ, req); 176 val = t4_read_reg(adap, A_PCIE_CFG_SPACE_DATA); 177 178 /* 179 * Reset F_ENABLE to 0 so reads of PCIE_CFG_SPACE_DATA won't cause a 180 * Configuration Space read. (None of the other fields matter when 181 * F_ENABLE is 0 so a simple register write is easier than a 182 * read-modify-write via t4_set_reg_field().) 183 */ 184 t4_write_reg(adap, A_PCIE_CFG_SPACE_REQ, 0); 185 186 return val; 187} 188 189/* 190 * t4_report_fw_error - report firmware error 191 * @adap: the adapter 192 * 193 * The adapter firmware can indicate error conditions to the host. 194 * If the firmware has indicated an error, print out the reason for 195 * the firmware error. 196 */ 197static void t4_report_fw_error(struct adapter *adap) 198{ 199 static const char *const reason[] = { 200 "Crash", /* PCIE_FW_EVAL_CRASH */ 201 "During Device Preparation", /* PCIE_FW_EVAL_PREP */ 202 "During Device Configuration", /* PCIE_FW_EVAL_CONF */ 203 "During Device Initialization", /* PCIE_FW_EVAL_INIT */ 204 "Unexpected Event", /* PCIE_FW_EVAL_UNEXPECTEDEVENT */ 205 "Insufficient Airflow", /* PCIE_FW_EVAL_OVERHEAT */ 206 "Device Shutdown", /* PCIE_FW_EVAL_DEVICESHUTDOWN */ 207 "Reserved", /* reserved */ 208 }; 209 u32 pcie_fw; 210 211 pcie_fw = t4_read_reg(adap, A_PCIE_FW); 212 if (pcie_fw & F_PCIE_FW_ERR) 213 CH_ERR(adap, "Firmware reports adapter error: %s\n", 214 reason[G_PCIE_FW_EVAL(pcie_fw)]); 215} 216 217/* 218 * Get the reply to a mailbox command and store it in @rpl in big-endian order. 219 */ 220static void get_mbox_rpl(struct adapter *adap, __be64 *rpl, int nflit, 221 u32 mbox_addr) 222{ 223 for ( ; nflit; nflit--, mbox_addr += 8) 224 *rpl++ = cpu_to_be64(t4_read_reg64(adap, mbox_addr)); 225} 226 227/* 228 * Handle a FW assertion reported in a mailbox. 229 */ 230static void fw_asrt(struct adapter *adap, struct fw_debug_cmd *asrt) 231{ 232 CH_ALERT(adap, 233 "FW assertion at %.16s:%u, val0 %#x, val1 %#x\n", 234 asrt->u.assert.filename_0_7, 235 be32_to_cpu(asrt->u.assert.line), 236 be32_to_cpu(asrt->u.assert.x), 237 be32_to_cpu(asrt->u.assert.y)); 238} 239 240#define X_CIM_PF_NOACCESS 0xeeeeeeee 241/** 242 * t4_wr_mbox_meat_timeout - send a command to FW through the given mailbox 243 * @adap: the adapter 244 * @mbox: index of the mailbox to use 245 * @cmd: the command to write 246 * @size: command length in bytes 247 * @rpl: where to optionally store the reply 248 * @sleep_ok: if true we may sleep while awaiting command completion 249 * @timeout: time to wait for command to finish before timing out 250 * (negative implies @sleep_ok=false) 251 * 252 * Sends the given command to FW through the selected mailbox and waits 253 * for the FW to execute the command. If @rpl is not %NULL it is used to 254 * store the FW's reply to the command. The command and its optional 255 * reply are of the same length. Some FW commands like RESET and 256 * INITIALIZE can take a considerable amount of time to execute. 257 * @sleep_ok determines whether we may sleep while awaiting the response. 258 * If sleeping is allowed we use progressive backoff otherwise we spin. 259 * Note that passing in a negative @timeout is an alternate mechanism 260 * for specifying @sleep_ok=false. This is useful when a higher level 261 * interface allows for specification of @timeout but not @sleep_ok ... 262 * 263 * The return value is 0 on success or a negative errno on failure. A 264 * failure can happen either because we are not able to execute the 265 * command or FW executes it but signals an error. In the latter case 266 * the return value is the error code indicated by FW (negated). 267 */ 268int t4_wr_mbox_meat_timeout(struct adapter *adap, int mbox, const void *cmd, 269 int size, void *rpl, bool sleep_ok, int timeout) 270{ 271 /* 272 * We delay in small increments at first in an effort to maintain 273 * responsiveness for simple, fast executing commands but then back 274 * off to larger delays to a maximum retry delay. 275 */ 276 static const int delay[] = { 277 1, 1, 3, 5, 10, 10, 20, 50, 100 278 }; 279 u32 v; 280 u64 res; 281 int i, ms, delay_idx, ret; 282 const __be64 *p = cmd; 283 u32 data_reg = PF_REG(mbox, A_CIM_PF_MAILBOX_DATA); 284 u32 ctl_reg = PF_REG(mbox, A_CIM_PF_MAILBOX_CTRL); 285 u32 ctl; 286 __be64 cmd_rpl[MBOX_LEN/8]; 287 u32 pcie_fw; 288 289 if (adap->flags & CHK_MBOX_ACCESS) 290 ASSERT_SYNCHRONIZED_OP(adap); 291 292 if ((size & 15) || size > MBOX_LEN) 293 return -EINVAL; 294 295 if (adap->flags & IS_VF) { 296 if (is_t6(adap)) 297 data_reg = FW_T6VF_MBDATA_BASE_ADDR; 298 else 299 data_reg = FW_T4VF_MBDATA_BASE_ADDR; 300 ctl_reg = VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_CTRL); 301 } 302 303 /* 304 * If we have a negative timeout, that implies that we can't sleep. 305 */ 306 if (timeout < 0) { 307 sleep_ok = false; 308 timeout = -timeout; 309 } 310 311 /* 312 * Attempt to gain access to the mailbox. 313 */ 314 for (i = 0; i < 4; i++) { 315 ctl = t4_read_reg(adap, ctl_reg); 316 v = G_MBOWNER(ctl); 317 if (v != X_MBOWNER_NONE) 318 break; 319 } 320 321 /* 322 * If we were unable to gain access, dequeue ourselves from the 323 * mailbox atomic access list and report the error to our caller. 324 */ 325 if (v != X_MBOWNER_PL) { 326 t4_report_fw_error(adap); 327 ret = (v == X_MBOWNER_FW) ? -EBUSY : -ETIMEDOUT; 328 return ret; 329 } 330 331 /* 332 * If we gain ownership of the mailbox and there's a "valid" message 333 * in it, this is likely an asynchronous error message from the 334 * firmware. So we'll report that and then proceed on with attempting 335 * to issue our own command ... which may well fail if the error 336 * presaged the firmware crashing ... 337 */ 338 if (ctl & F_MBMSGVALID) { 339 CH_ERR(adap, "found VALID command in mbox %u: %016llx %016llx " 340 "%016llx %016llx %016llx %016llx %016llx %016llx\n", 341 mbox, (unsigned long long)t4_read_reg64(adap, data_reg), 342 (unsigned long long)t4_read_reg64(adap, data_reg + 8), 343 (unsigned long long)t4_read_reg64(adap, data_reg + 16), 344 (unsigned long long)t4_read_reg64(adap, data_reg + 24), 345 (unsigned long long)t4_read_reg64(adap, data_reg + 32), 346 (unsigned long long)t4_read_reg64(adap, data_reg + 40), 347 (unsigned long long)t4_read_reg64(adap, data_reg + 48), 348 (unsigned long long)t4_read_reg64(adap, data_reg + 56)); 349 } 350 351 /* 352 * Copy in the new mailbox command and send it on its way ... 353 */ 354 for (i = 0; i < size; i += 8, p++) 355 t4_write_reg64(adap, data_reg + i, be64_to_cpu(*p)); 356 357 if (adap->flags & IS_VF) { 358 /* 359 * For the VFs, the Mailbox Data "registers" are 360 * actually backed by T4's "MA" interface rather than 361 * PL Registers (as is the case for the PFs). Because 362 * these are in different coherency domains, the write 363 * to the VF's PL-register-backed Mailbox Control can 364 * race in front of the writes to the MA-backed VF 365 * Mailbox Data "registers". So we need to do a 366 * read-back on at least one byte of the VF Mailbox 367 * Data registers before doing the write to the VF 368 * Mailbox Control register. 369 */ 370 t4_read_reg(adap, data_reg); 371 } 372 373 CH_DUMP_MBOX(adap, mbox, data_reg); 374 375 t4_write_reg(adap, ctl_reg, F_MBMSGVALID | V_MBOWNER(X_MBOWNER_FW)); 376 t4_read_reg(adap, ctl_reg); /* flush write */ 377 378 delay_idx = 0; 379 ms = delay[0]; 380 381 /* 382 * Loop waiting for the reply; bail out if we time out or the firmware 383 * reports an error. 384 */ 385 pcie_fw = 0; 386 for (i = 0; i < timeout; i += ms) { 387 if (!(adap->flags & IS_VF)) { 388 pcie_fw = t4_read_reg(adap, A_PCIE_FW); 389 if (pcie_fw & F_PCIE_FW_ERR) 390 break; 391 } 392 if (sleep_ok) { 393 ms = delay[delay_idx]; /* last element may repeat */ 394 if (delay_idx < ARRAY_SIZE(delay) - 1) 395 delay_idx++; 396 msleep(ms); 397 } else { 398 mdelay(ms); 399 } 400 401 v = t4_read_reg(adap, ctl_reg); 402 if (v == X_CIM_PF_NOACCESS) 403 continue; 404 if (G_MBOWNER(v) == X_MBOWNER_PL) { 405 if (!(v & F_MBMSGVALID)) { 406 t4_write_reg(adap, ctl_reg, 407 V_MBOWNER(X_MBOWNER_NONE)); 408 continue; 409 } 410 411 /* 412 * Retrieve the command reply and release the mailbox. 413 */ 414 get_mbox_rpl(adap, cmd_rpl, MBOX_LEN/8, data_reg); 415 t4_write_reg(adap, ctl_reg, V_MBOWNER(X_MBOWNER_NONE)); 416 417 CH_DUMP_MBOX(adap, mbox, data_reg); 418 419 res = be64_to_cpu(cmd_rpl[0]); 420 if (G_FW_CMD_OP(res >> 32) == FW_DEBUG_CMD) { 421 fw_asrt(adap, (struct fw_debug_cmd *)cmd_rpl); 422 res = V_FW_CMD_RETVAL(EIO); 423 } else if (rpl) 424 memcpy(rpl, cmd_rpl, size); 425 return -G_FW_CMD_RETVAL((int)res); 426 } 427 } 428 429 /* 430 * We timed out waiting for a reply to our mailbox command. Report 431 * the error and also check to see if the firmware reported any 432 * errors ... 433 */ 434 ret = (pcie_fw & F_PCIE_FW_ERR) ? -ENXIO : -ETIMEDOUT; 435 CH_ERR(adap, "command %#x in mailbox %d timed out\n", 436 *(const u8 *)cmd, mbox); 437 438 /* If DUMP_MBOX is set the mbox has already been dumped */ 439 if ((adap->debug_flags & DF_DUMP_MBOX) == 0) { 440 p = cmd; 441 CH_ERR(adap, "mbox: %016llx %016llx %016llx %016llx " 442 "%016llx %016llx %016llx %016llx\n", 443 (unsigned long long)be64_to_cpu(p[0]), 444 (unsigned long long)be64_to_cpu(p[1]), 445 (unsigned long long)be64_to_cpu(p[2]), 446 (unsigned long long)be64_to_cpu(p[3]), 447 (unsigned long long)be64_to_cpu(p[4]), 448 (unsigned long long)be64_to_cpu(p[5]), 449 (unsigned long long)be64_to_cpu(p[6]), 450 (unsigned long long)be64_to_cpu(p[7])); 451 } 452 453 t4_report_fw_error(adap); 454 t4_fatal_err(adap); 455 return ret; 456} 457 458int t4_wr_mbox_meat(struct adapter *adap, int mbox, const void *cmd, int size, 459 void *rpl, bool sleep_ok) 460{ 461 return t4_wr_mbox_meat_timeout(adap, mbox, cmd, size, rpl, 462 sleep_ok, FW_CMD_MAX_TIMEOUT); 463 464} 465 466static int t4_edc_err_read(struct adapter *adap, int idx) 467{ 468 u32 edc_ecc_err_addr_reg; 469 u32 edc_bist_status_rdata_reg; 470 471 if (is_t4(adap)) { 472 CH_WARN(adap, "%s: T4 NOT supported.\n", __func__); 473 return 0; 474 } 475 if (idx != MEM_EDC0 && idx != MEM_EDC1) { 476 CH_WARN(adap, "%s: idx %d NOT supported.\n", __func__, idx); 477 return 0; 478 } 479 480 edc_ecc_err_addr_reg = EDC_T5_REG(A_EDC_H_ECC_ERR_ADDR, idx); 481 edc_bist_status_rdata_reg = EDC_T5_REG(A_EDC_H_BIST_STATUS_RDATA, idx); 482 483 CH_WARN(adap, 484 "edc%d err addr 0x%x: 0x%x.\n", 485 idx, edc_ecc_err_addr_reg, 486 t4_read_reg(adap, edc_ecc_err_addr_reg)); 487 CH_WARN(adap, 488 "bist: 0x%x, status %llx %llx %llx %llx %llx %llx %llx %llx %llx.\n", 489 edc_bist_status_rdata_reg, 490 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg), 491 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 8), 492 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 16), 493 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 24), 494 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 32), 495 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 40), 496 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 48), 497 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 56), 498 (unsigned long long)t4_read_reg64(adap, edc_bist_status_rdata_reg + 64)); 499 500 return 0; 501} 502 503/** 504 * t4_mc_read - read from MC through backdoor accesses 505 * @adap: the adapter 506 * @idx: which MC to access 507 * @addr: address of first byte requested 508 * @data: 64 bytes of data containing the requested address 509 * @ecc: where to store the corresponding 64-bit ECC word 510 * 511 * Read 64 bytes of data from MC starting at a 64-byte-aligned address 512 * that covers the requested address @addr. If @parity is not %NULL it 513 * is assigned the 64-bit ECC word for the read data. 514 */ 515int t4_mc_read(struct adapter *adap, int idx, u32 addr, __be32 *data, u64 *ecc) 516{ 517 int i; 518 u32 mc_bist_cmd_reg, mc_bist_cmd_addr_reg, mc_bist_cmd_len_reg; 519 u32 mc_bist_status_rdata_reg, mc_bist_data_pattern_reg; 520 521 if (is_t4(adap)) { 522 mc_bist_cmd_reg = A_MC_BIST_CMD; 523 mc_bist_cmd_addr_reg = A_MC_BIST_CMD_ADDR; 524 mc_bist_cmd_len_reg = A_MC_BIST_CMD_LEN; 525 mc_bist_status_rdata_reg = A_MC_BIST_STATUS_RDATA; 526 mc_bist_data_pattern_reg = A_MC_BIST_DATA_PATTERN; 527 } else { 528 mc_bist_cmd_reg = MC_REG(A_MC_P_BIST_CMD, idx); 529 mc_bist_cmd_addr_reg = MC_REG(A_MC_P_BIST_CMD_ADDR, idx); 530 mc_bist_cmd_len_reg = MC_REG(A_MC_P_BIST_CMD_LEN, idx); 531 mc_bist_status_rdata_reg = MC_REG(A_MC_P_BIST_STATUS_RDATA, 532 idx); 533 mc_bist_data_pattern_reg = MC_REG(A_MC_P_BIST_DATA_PATTERN, 534 idx); 535 } 536 537 if (t4_read_reg(adap, mc_bist_cmd_reg) & F_START_BIST) 538 return -EBUSY; 539 t4_write_reg(adap, mc_bist_cmd_addr_reg, addr & ~0x3fU); 540 t4_write_reg(adap, mc_bist_cmd_len_reg, 64); 541 t4_write_reg(adap, mc_bist_data_pattern_reg, 0xc); 542 t4_write_reg(adap, mc_bist_cmd_reg, V_BIST_OPCODE(1) | 543 F_START_BIST | V_BIST_CMD_GAP(1)); 544 i = t4_wait_op_done(adap, mc_bist_cmd_reg, F_START_BIST, 0, 10, 1); 545 if (i) 546 return i; 547 548#define MC_DATA(i) MC_BIST_STATUS_REG(mc_bist_status_rdata_reg, i) 549 550 for (i = 15; i >= 0; i--) 551 *data++ = ntohl(t4_read_reg(adap, MC_DATA(i))); 552 if (ecc) 553 *ecc = t4_read_reg64(adap, MC_DATA(16)); 554#undef MC_DATA 555 return 0; 556} 557 558/** 559 * t4_edc_read - read from EDC through backdoor accesses 560 * @adap: the adapter 561 * @idx: which EDC to access 562 * @addr: address of first byte requested 563 * @data: 64 bytes of data containing the requested address 564 * @ecc: where to store the corresponding 64-bit ECC word 565 * 566 * Read 64 bytes of data from EDC starting at a 64-byte-aligned address 567 * that covers the requested address @addr. If @parity is not %NULL it 568 * is assigned the 64-bit ECC word for the read data. 569 */ 570int t4_edc_read(struct adapter *adap, int idx, u32 addr, __be32 *data, u64 *ecc) 571{ 572 int i; 573 u32 edc_bist_cmd_reg, edc_bist_cmd_addr_reg, edc_bist_cmd_len_reg; 574 u32 edc_bist_cmd_data_pattern, edc_bist_status_rdata_reg; 575 576 if (is_t4(adap)) { 577 edc_bist_cmd_reg = EDC_REG(A_EDC_BIST_CMD, idx); 578 edc_bist_cmd_addr_reg = EDC_REG(A_EDC_BIST_CMD_ADDR, idx); 579 edc_bist_cmd_len_reg = EDC_REG(A_EDC_BIST_CMD_LEN, idx); 580 edc_bist_cmd_data_pattern = EDC_REG(A_EDC_BIST_DATA_PATTERN, 581 idx); 582 edc_bist_status_rdata_reg = EDC_REG(A_EDC_BIST_STATUS_RDATA, 583 idx); 584 } else { 585/* 586 * These macro are missing in t4_regs.h file. 587 * Added temporarily for testing. 588 */ 589#define EDC_STRIDE_T5 (EDC_T51_BASE_ADDR - EDC_T50_BASE_ADDR) 590#define EDC_REG_T5(reg, idx) (reg + EDC_STRIDE_T5 * idx) 591 edc_bist_cmd_reg = EDC_REG_T5(A_EDC_H_BIST_CMD, idx); 592 edc_bist_cmd_addr_reg = EDC_REG_T5(A_EDC_H_BIST_CMD_ADDR, idx); 593 edc_bist_cmd_len_reg = EDC_REG_T5(A_EDC_H_BIST_CMD_LEN, idx); 594 edc_bist_cmd_data_pattern = EDC_REG_T5(A_EDC_H_BIST_DATA_PATTERN, 595 idx); 596 edc_bist_status_rdata_reg = EDC_REG_T5(A_EDC_H_BIST_STATUS_RDATA, 597 idx); 598#undef EDC_REG_T5 599#undef EDC_STRIDE_T5 600 } 601 602 if (t4_read_reg(adap, edc_bist_cmd_reg) & F_START_BIST) 603 return -EBUSY; 604 t4_write_reg(adap, edc_bist_cmd_addr_reg, addr & ~0x3fU); 605 t4_write_reg(adap, edc_bist_cmd_len_reg, 64); 606 t4_write_reg(adap, edc_bist_cmd_data_pattern, 0xc); 607 t4_write_reg(adap, edc_bist_cmd_reg, 608 V_BIST_OPCODE(1) | V_BIST_CMD_GAP(1) | F_START_BIST); 609 i = t4_wait_op_done(adap, edc_bist_cmd_reg, F_START_BIST, 0, 10, 1); 610 if (i) 611 return i; 612 613#define EDC_DATA(i) EDC_BIST_STATUS_REG(edc_bist_status_rdata_reg, i) 614 615 for (i = 15; i >= 0; i--) 616 *data++ = ntohl(t4_read_reg(adap, EDC_DATA(i))); 617 if (ecc) 618 *ecc = t4_read_reg64(adap, EDC_DATA(16)); 619#undef EDC_DATA 620 return 0; 621} 622 623/** 624 * t4_mem_read - read EDC 0, EDC 1 or MC into buffer 625 * @adap: the adapter 626 * @mtype: memory type: MEM_EDC0, MEM_EDC1 or MEM_MC 627 * @addr: address within indicated memory type 628 * @len: amount of memory to read 629 * @buf: host memory buffer 630 * 631 * Reads an [almost] arbitrary memory region in the firmware: the 632 * firmware memory address, length and host buffer must be aligned on 633 * 32-bit boudaries. The memory is returned as a raw byte sequence from 634 * the firmware's memory. If this memory contains data structures which 635 * contain multi-byte integers, it's the callers responsibility to 636 * perform appropriate byte order conversions. 637 */ 638int t4_mem_read(struct adapter *adap, int mtype, u32 addr, u32 len, 639 __be32 *buf) 640{ 641 u32 pos, start, end, offset; 642 int ret; 643 644 /* 645 * Argument sanity checks ... 646 */ 647 if ((addr & 0x3) || (len & 0x3)) 648 return -EINVAL; 649 650 /* 651 * The underlaying EDC/MC read routines read 64 bytes at a time so we 652 * need to round down the start and round up the end. We'll start 653 * copying out of the first line at (addr - start) a word at a time. 654 */ 655 start = rounddown2(addr, 64); 656 end = roundup2(addr + len, 64); 657 offset = (addr - start)/sizeof(__be32); 658 659 for (pos = start; pos < end; pos += 64, offset = 0) { 660 __be32 data[16]; 661 662 /* 663 * Read the chip's memory block and bail if there's an error. 664 */ 665 if ((mtype == MEM_MC) || (mtype == MEM_MC1)) 666 ret = t4_mc_read(adap, mtype - MEM_MC, pos, data, NULL); 667 else 668 ret = t4_edc_read(adap, mtype, pos, data, NULL); 669 if (ret) 670 return ret; 671 672 /* 673 * Copy the data into the caller's memory buffer. 674 */ 675 while (offset < 16 && len > 0) { 676 *buf++ = data[offset++]; 677 len -= sizeof(__be32); 678 } 679 } 680 681 return 0; 682} 683 684/* 685 * Return the specified PCI-E Configuration Space register from our Physical 686 * Function. We try first via a Firmware LDST Command (if fw_attach != 0) 687 * since we prefer to let the firmware own all of these registers, but if that 688 * fails we go for it directly ourselves. 689 */ 690u32 t4_read_pcie_cfg4(struct adapter *adap, int reg, int drv_fw_attach) 691{ 692 693 /* 694 * If fw_attach != 0, construct and send the Firmware LDST Command to 695 * retrieve the specified PCI-E Configuration Space register. 696 */ 697 if (drv_fw_attach != 0) { 698 struct fw_ldst_cmd ldst_cmd; 699 int ret; 700 701 memset(&ldst_cmd, 0, sizeof(ldst_cmd)); 702 ldst_cmd.op_to_addrspace = 703 cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 704 F_FW_CMD_REQUEST | 705 F_FW_CMD_READ | 706 V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_FUNC_PCIE)); 707 ldst_cmd.cycles_to_len16 = cpu_to_be32(FW_LEN16(ldst_cmd)); 708 ldst_cmd.u.pcie.select_naccess = V_FW_LDST_CMD_NACCESS(1); 709 ldst_cmd.u.pcie.ctrl_to_fn = 710 (F_FW_LDST_CMD_LC | V_FW_LDST_CMD_FN(adap->pf)); 711 ldst_cmd.u.pcie.r = reg; 712 713 /* 714 * If the LDST Command succeeds, return the result, otherwise 715 * fall through to reading it directly ourselves ... 716 */ 717 ret = t4_wr_mbox(adap, adap->mbox, &ldst_cmd, sizeof(ldst_cmd), 718 &ldst_cmd); 719 if (ret == 0) 720 return be32_to_cpu(ldst_cmd.u.pcie.data[0]); 721 722 CH_WARN(adap, "Firmware failed to return " 723 "Configuration Space register %d, err = %d\n", 724 reg, -ret); 725 } 726 727 /* 728 * Read the desired Configuration Space register via the PCI-E 729 * Backdoor mechanism. 730 */ 731 return t4_hw_pci_read_cfg4(adap, reg); 732} 733 734/** 735 * t4_get_regs_len - return the size of the chips register set 736 * @adapter: the adapter 737 * 738 * Returns the size of the chip's BAR0 register space. 739 */ 740unsigned int t4_get_regs_len(struct adapter *adapter) 741{ 742 unsigned int chip_version = chip_id(adapter); 743 744 switch (chip_version) { 745 case CHELSIO_T4: 746 if (adapter->flags & IS_VF) 747 return FW_T4VF_REGMAP_SIZE; 748 return T4_REGMAP_SIZE; 749 750 case CHELSIO_T5: 751 case CHELSIO_T6: 752 if (adapter->flags & IS_VF) 753 return FW_T4VF_REGMAP_SIZE; 754 return T5_REGMAP_SIZE; 755 } 756 757 CH_ERR(adapter, 758 "Unsupported chip version %d\n", chip_version); 759 return 0; 760} 761 762/** 763 * t4_get_regs - read chip registers into provided buffer 764 * @adap: the adapter 765 * @buf: register buffer 766 * @buf_size: size (in bytes) of register buffer 767 * 768 * If the provided register buffer isn't large enough for the chip's 769 * full register range, the register dump will be truncated to the 770 * register buffer's size. 771 */ 772void t4_get_regs(struct adapter *adap, u8 *buf, size_t buf_size) 773{ 774 static const unsigned int t4_reg_ranges[] = { 775 0x1008, 0x1108, 776 0x1180, 0x1184, 777 0x1190, 0x1194, 778 0x11a0, 0x11a4, 779 0x11b0, 0x11b4, 780 0x11fc, 0x123c, 781 0x1300, 0x173c, 782 0x1800, 0x18fc, 783 0x3000, 0x30d8, 784 0x30e0, 0x30e4, 785 0x30ec, 0x5910, 786 0x5920, 0x5924, 787 0x5960, 0x5960, 788 0x5968, 0x5968, 789 0x5970, 0x5970, 790 0x5978, 0x5978, 791 0x5980, 0x5980, 792 0x5988, 0x5988, 793 0x5990, 0x5990, 794 0x5998, 0x5998, 795 0x59a0, 0x59d4, 796 0x5a00, 0x5ae0, 797 0x5ae8, 0x5ae8, 798 0x5af0, 0x5af0, 799 0x5af8, 0x5af8, 800 0x6000, 0x6098, 801 0x6100, 0x6150, 802 0x6200, 0x6208, 803 0x6240, 0x6248, 804 0x6280, 0x62b0, 805 0x62c0, 0x6338, 806 0x6370, 0x638c, 807 0x6400, 0x643c, 808 0x6500, 0x6524, 809 0x6a00, 0x6a04, 810 0x6a14, 0x6a38, 811 0x6a60, 0x6a70, 812 0x6a78, 0x6a78, 813 0x6b00, 0x6b0c, 814 0x6b1c, 0x6b84, 815 0x6bf0, 0x6bf8, 816 0x6c00, 0x6c0c, 817 0x6c1c, 0x6c84, 818 0x6cf0, 0x6cf8, 819 0x6d00, 0x6d0c, 820 0x6d1c, 0x6d84, 821 0x6df0, 0x6df8, 822 0x6e00, 0x6e0c, 823 0x6e1c, 0x6e84, 824 0x6ef0, 0x6ef8, 825 0x6f00, 0x6f0c, 826 0x6f1c, 0x6f84, 827 0x6ff0, 0x6ff8, 828 0x7000, 0x700c, 829 0x701c, 0x7084, 830 0x70f0, 0x70f8, 831 0x7100, 0x710c, 832 0x711c, 0x7184, 833 0x71f0, 0x71f8, 834 0x7200, 0x720c, 835 0x721c, 0x7284, 836 0x72f0, 0x72f8, 837 0x7300, 0x730c, 838 0x731c, 0x7384, 839 0x73f0, 0x73f8, 840 0x7400, 0x7450, 841 0x7500, 0x7530, 842 0x7600, 0x760c, 843 0x7614, 0x761c, 844 0x7680, 0x76cc, 845 0x7700, 0x7798, 846 0x77c0, 0x77fc, 847 0x7900, 0x79fc, 848 0x7b00, 0x7b58, 849 0x7b60, 0x7b84, 850 0x7b8c, 0x7c38, 851 0x7d00, 0x7d38, 852 0x7d40, 0x7d80, 853 0x7d8c, 0x7ddc, 854 0x7de4, 0x7e04, 855 0x7e10, 0x7e1c, 856 0x7e24, 0x7e38, 857 0x7e40, 0x7e44, 858 0x7e4c, 0x7e78, 859 0x7e80, 0x7ea4, 860 0x7eac, 0x7edc, 861 0x7ee8, 0x7efc, 862 0x8dc0, 0x8e04, 863 0x8e10, 0x8e1c, 864 0x8e30, 0x8e78, 865 0x8ea0, 0x8eb8, 866 0x8ec0, 0x8f6c, 867 0x8fc0, 0x9008, 868 0x9010, 0x9058, 869 0x9060, 0x9060, 870 0x9068, 0x9074, 871 0x90fc, 0x90fc, 872 0x9400, 0x9408, 873 0x9410, 0x9458, 874 0x9600, 0x9600, 875 0x9608, 0x9638, 876 0x9640, 0x96bc, 877 0x9800, 0x9808, 878 0x9820, 0x983c, 879 0x9850, 0x9864, 880 0x9c00, 0x9c6c, 881 0x9c80, 0x9cec, 882 0x9d00, 0x9d6c, 883 0x9d80, 0x9dec, 884 0x9e00, 0x9e6c, 885 0x9e80, 0x9eec, 886 0x9f00, 0x9f6c, 887 0x9f80, 0x9fec, 888 0xd004, 0xd004, 889 0xd010, 0xd03c, 890 0xdfc0, 0xdfe0, 891 0xe000, 0xea7c, 892 0xf000, 0x11110, 893 0x11118, 0x11190, 894 0x19040, 0x1906c, 895 0x19078, 0x19080, 896 0x1908c, 0x190e4, 897 0x190f0, 0x190f8, 898 0x19100, 0x19110, 899 0x19120, 0x19124, 900 0x19150, 0x19194, 901 0x1919c, 0x191b0, 902 0x191d0, 0x191e8, 903 0x19238, 0x1924c, 904 0x193f8, 0x1943c, 905 0x1944c, 0x19474, 906 0x19490, 0x194e0, 907 0x194f0, 0x194f8, 908 0x19800, 0x19c08, 909 0x19c10, 0x19c90, 910 0x19ca0, 0x19ce4, 911 0x19cf0, 0x19d40, 912 0x19d50, 0x19d94, 913 0x19da0, 0x19de8, 914 0x19df0, 0x19e40, 915 0x19e50, 0x19e90, 916 0x19ea0, 0x19f4c, 917 0x1a000, 0x1a004, 918 0x1a010, 0x1a06c, 919 0x1a0b0, 0x1a0e4, 920 0x1a0ec, 0x1a0f4, 921 0x1a100, 0x1a108, 922 0x1a114, 0x1a120, 923 0x1a128, 0x1a130, 924 0x1a138, 0x1a138, 925 0x1a190, 0x1a1c4, 926 0x1a1fc, 0x1a1fc, 927 0x1e040, 0x1e04c, 928 0x1e284, 0x1e28c, 929 0x1e2c0, 0x1e2c0, 930 0x1e2e0, 0x1e2e0, 931 0x1e300, 0x1e384, 932 0x1e3c0, 0x1e3c8, 933 0x1e440, 0x1e44c, 934 0x1e684, 0x1e68c, 935 0x1e6c0, 0x1e6c0, 936 0x1e6e0, 0x1e6e0, 937 0x1e700, 0x1e784, 938 0x1e7c0, 0x1e7c8, 939 0x1e840, 0x1e84c, 940 0x1ea84, 0x1ea8c, 941 0x1eac0, 0x1eac0, 942 0x1eae0, 0x1eae0, 943 0x1eb00, 0x1eb84, 944 0x1ebc0, 0x1ebc8, 945 0x1ec40, 0x1ec4c, 946 0x1ee84, 0x1ee8c, 947 0x1eec0, 0x1eec0, 948 0x1eee0, 0x1eee0, 949 0x1ef00, 0x1ef84, 950 0x1efc0, 0x1efc8, 951 0x1f040, 0x1f04c, 952 0x1f284, 0x1f28c, 953 0x1f2c0, 0x1f2c0, 954 0x1f2e0, 0x1f2e0, 955 0x1f300, 0x1f384, 956 0x1f3c0, 0x1f3c8, 957 0x1f440, 0x1f44c, 958 0x1f684, 0x1f68c, 959 0x1f6c0, 0x1f6c0, 960 0x1f6e0, 0x1f6e0, 961 0x1f700, 0x1f784, 962 0x1f7c0, 0x1f7c8, 963 0x1f840, 0x1f84c, 964 0x1fa84, 0x1fa8c, 965 0x1fac0, 0x1fac0, 966 0x1fae0, 0x1fae0, 967 0x1fb00, 0x1fb84, 968 0x1fbc0, 0x1fbc8, 969 0x1fc40, 0x1fc4c, 970 0x1fe84, 0x1fe8c, 971 0x1fec0, 0x1fec0, 972 0x1fee0, 0x1fee0, 973 0x1ff00, 0x1ff84, 974 0x1ffc0, 0x1ffc8, 975 0x20000, 0x2002c, 976 0x20100, 0x2013c, 977 0x20190, 0x201a0, 978 0x201a8, 0x201b8, 979 0x201c4, 0x201c8, 980 0x20200, 0x20318, 981 0x20400, 0x204b4, 982 0x204c0, 0x20528, 983 0x20540, 0x20614, 984 0x21000, 0x21040, 985 0x2104c, 0x21060, 986 0x210c0, 0x210ec, 987 0x21200, 0x21268, 988 0x21270, 0x21284, 989 0x212fc, 0x21388, 990 0x21400, 0x21404, 991 0x21500, 0x21500, 992 0x21510, 0x21518, 993 0x2152c, 0x21530, 994 0x2153c, 0x2153c, 995 0x21550, 0x21554, 996 0x21600, 0x21600, 997 0x21608, 0x2161c, 998 0x21624, 0x21628, 999 0x21630, 0x21634, 1000 0x2163c, 0x2163c, 1001 0x21700, 0x2171c, 1002 0x21780, 0x2178c, 1003 0x21800, 0x21818, 1004 0x21820, 0x21828, 1005 0x21830, 0x21848, 1006 0x21850, 0x21854, 1007 0x21860, 0x21868, 1008 0x21870, 0x21870, 1009 0x21878, 0x21898, 1010 0x218a0, 0x218a8, 1011 0x218b0, 0x218c8, 1012 0x218d0, 0x218d4, 1013 0x218e0, 0x218e8, 1014 0x218f0, 0x218f0, 1015 0x218f8, 0x21a18, 1016 0x21a20, 0x21a28, 1017 0x21a30, 0x21a48, 1018 0x21a50, 0x21a54, 1019 0x21a60, 0x21a68, 1020 0x21a70, 0x21a70, 1021 0x21a78, 0x21a98, 1022 0x21aa0, 0x21aa8, 1023 0x21ab0, 0x21ac8, 1024 0x21ad0, 0x21ad4, 1025 0x21ae0, 0x21ae8, 1026 0x21af0, 0x21af0, 1027 0x21af8, 0x21c18, 1028 0x21c20, 0x21c20, 1029 0x21c28, 0x21c30, 1030 0x21c38, 0x21c38, 1031 0x21c80, 0x21c98, 1032 0x21ca0, 0x21ca8, 1033 0x21cb0, 0x21cc8, 1034 0x21cd0, 0x21cd4, 1035 0x21ce0, 0x21ce8, 1036 0x21cf0, 0x21cf0, 1037 0x21cf8, 0x21d7c, 1038 0x21e00, 0x21e04, 1039 0x22000, 0x2202c, 1040 0x22100, 0x2213c, 1041 0x22190, 0x221a0, 1042 0x221a8, 0x221b8, 1043 0x221c4, 0x221c8, 1044 0x22200, 0x22318, 1045 0x22400, 0x224b4, 1046 0x224c0, 0x22528, 1047 0x22540, 0x22614, 1048 0x23000, 0x23040, 1049 0x2304c, 0x23060, 1050 0x230c0, 0x230ec, 1051 0x23200, 0x23268, 1052 0x23270, 0x23284, 1053 0x232fc, 0x23388, 1054 0x23400, 0x23404, 1055 0x23500, 0x23500, 1056 0x23510, 0x23518, 1057 0x2352c, 0x23530, 1058 0x2353c, 0x2353c, 1059 0x23550, 0x23554, 1060 0x23600, 0x23600, 1061 0x23608, 0x2361c, 1062 0x23624, 0x23628, 1063 0x23630, 0x23634, 1064 0x2363c, 0x2363c, 1065 0x23700, 0x2371c, 1066 0x23780, 0x2378c, 1067 0x23800, 0x23818, 1068 0x23820, 0x23828, 1069 0x23830, 0x23848, 1070 0x23850, 0x23854, 1071 0x23860, 0x23868, 1072 0x23870, 0x23870, 1073 0x23878, 0x23898, 1074 0x238a0, 0x238a8, 1075 0x238b0, 0x238c8, 1076 0x238d0, 0x238d4, 1077 0x238e0, 0x238e8, 1078 0x238f0, 0x238f0, 1079 0x238f8, 0x23a18, 1080 0x23a20, 0x23a28, 1081 0x23a30, 0x23a48, 1082 0x23a50, 0x23a54, 1083 0x23a60, 0x23a68, 1084 0x23a70, 0x23a70, 1085 0x23a78, 0x23a98, 1086 0x23aa0, 0x23aa8, 1087 0x23ab0, 0x23ac8, 1088 0x23ad0, 0x23ad4, 1089 0x23ae0, 0x23ae8, 1090 0x23af0, 0x23af0, 1091 0x23af8, 0x23c18, 1092 0x23c20, 0x23c20, 1093 0x23c28, 0x23c30, 1094 0x23c38, 0x23c38, 1095 0x23c80, 0x23c98, 1096 0x23ca0, 0x23ca8, 1097 0x23cb0, 0x23cc8, 1098 0x23cd0, 0x23cd4, 1099 0x23ce0, 0x23ce8, 1100 0x23cf0, 0x23cf0, 1101 0x23cf8, 0x23d7c, 1102 0x23e00, 0x23e04, 1103 0x24000, 0x2402c, 1104 0x24100, 0x2413c, 1105 0x24190, 0x241a0, 1106 0x241a8, 0x241b8, 1107 0x241c4, 0x241c8, 1108 0x24200, 0x24318, 1109 0x24400, 0x244b4, 1110 0x244c0, 0x24528, 1111 0x24540, 0x24614, 1112 0x25000, 0x25040, 1113 0x2504c, 0x25060, 1114 0x250c0, 0x250ec, 1115 0x25200, 0x25268, 1116 0x25270, 0x25284, 1117 0x252fc, 0x25388, 1118 0x25400, 0x25404, 1119 0x25500, 0x25500, 1120 0x25510, 0x25518, 1121 0x2552c, 0x25530, 1122 0x2553c, 0x2553c, 1123 0x25550, 0x25554, 1124 0x25600, 0x25600, 1125 0x25608, 0x2561c, 1126 0x25624, 0x25628, 1127 0x25630, 0x25634, 1128 0x2563c, 0x2563c, 1129 0x25700, 0x2571c, 1130 0x25780, 0x2578c, 1131 0x25800, 0x25818, 1132 0x25820, 0x25828, 1133 0x25830, 0x25848, 1134 0x25850, 0x25854, 1135 0x25860, 0x25868, 1136 0x25870, 0x25870, 1137 0x25878, 0x25898, 1138 0x258a0, 0x258a8, 1139 0x258b0, 0x258c8, 1140 0x258d0, 0x258d4, 1141 0x258e0, 0x258e8, 1142 0x258f0, 0x258f0, 1143 0x258f8, 0x25a18, 1144 0x25a20, 0x25a28, 1145 0x25a30, 0x25a48, 1146 0x25a50, 0x25a54, 1147 0x25a60, 0x25a68, 1148 0x25a70, 0x25a70, 1149 0x25a78, 0x25a98, 1150 0x25aa0, 0x25aa8, 1151 0x25ab0, 0x25ac8, 1152 0x25ad0, 0x25ad4, 1153 0x25ae0, 0x25ae8, 1154 0x25af0, 0x25af0, 1155 0x25af8, 0x25c18, 1156 0x25c20, 0x25c20, 1157 0x25c28, 0x25c30, 1158 0x25c38, 0x25c38, 1159 0x25c80, 0x25c98, 1160 0x25ca0, 0x25ca8, 1161 0x25cb0, 0x25cc8, 1162 0x25cd0, 0x25cd4, 1163 0x25ce0, 0x25ce8, 1164 0x25cf0, 0x25cf0, 1165 0x25cf8, 0x25d7c, 1166 0x25e00, 0x25e04, 1167 0x26000, 0x2602c, 1168 0x26100, 0x2613c, 1169 0x26190, 0x261a0, 1170 0x261a8, 0x261b8, 1171 0x261c4, 0x261c8, 1172 0x26200, 0x26318, 1173 0x26400, 0x264b4, 1174 0x264c0, 0x26528, 1175 0x26540, 0x26614, 1176 0x27000, 0x27040, 1177 0x2704c, 0x27060, 1178 0x270c0, 0x270ec, 1179 0x27200, 0x27268, 1180 0x27270, 0x27284, 1181 0x272fc, 0x27388, 1182 0x27400, 0x27404, 1183 0x27500, 0x27500, 1184 0x27510, 0x27518, 1185 0x2752c, 0x27530, 1186 0x2753c, 0x2753c, 1187 0x27550, 0x27554, 1188 0x27600, 0x27600, 1189 0x27608, 0x2761c, 1190 0x27624, 0x27628, 1191 0x27630, 0x27634, 1192 0x2763c, 0x2763c, 1193 0x27700, 0x2771c, 1194 0x27780, 0x2778c, 1195 0x27800, 0x27818, 1196 0x27820, 0x27828, 1197 0x27830, 0x27848, 1198 0x27850, 0x27854, 1199 0x27860, 0x27868, 1200 0x27870, 0x27870, 1201 0x27878, 0x27898, 1202 0x278a0, 0x278a8, 1203 0x278b0, 0x278c8, 1204 0x278d0, 0x278d4, 1205 0x278e0, 0x278e8, 1206 0x278f0, 0x278f0, 1207 0x278f8, 0x27a18, 1208 0x27a20, 0x27a28, 1209 0x27a30, 0x27a48, 1210 0x27a50, 0x27a54, 1211 0x27a60, 0x27a68, 1212 0x27a70, 0x27a70, 1213 0x27a78, 0x27a98, 1214 0x27aa0, 0x27aa8, 1215 0x27ab0, 0x27ac8, 1216 0x27ad0, 0x27ad4, 1217 0x27ae0, 0x27ae8, 1218 0x27af0, 0x27af0, 1219 0x27af8, 0x27c18, 1220 0x27c20, 0x27c20, 1221 0x27c28, 0x27c30, 1222 0x27c38, 0x27c38, 1223 0x27c80, 0x27c98, 1224 0x27ca0, 0x27ca8, 1225 0x27cb0, 0x27cc8, 1226 0x27cd0, 0x27cd4, 1227 0x27ce0, 0x27ce8, 1228 0x27cf0, 0x27cf0, 1229 0x27cf8, 0x27d7c, 1230 0x27e00, 0x27e04, 1231 }; 1232 1233 static const unsigned int t4vf_reg_ranges[] = { 1234 VF_SGE_REG(A_SGE_VF_KDOORBELL), VF_SGE_REG(A_SGE_VF_GTS), 1235 VF_MPS_REG(A_MPS_VF_CTL), 1236 VF_MPS_REG(A_MPS_VF_STAT_RX_VF_ERR_FRAMES_H), 1237 VF_PL_REG(A_PL_VF_WHOAMI), VF_PL_REG(A_PL_VF_WHOAMI), 1238 VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_CTRL), 1239 VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_STATUS), 1240 FW_T4VF_MBDATA_BASE_ADDR, 1241 FW_T4VF_MBDATA_BASE_ADDR + 1242 ((NUM_CIM_PF_MAILBOX_DATA_INSTANCES - 1) * 4), 1243 }; 1244 1245 static const unsigned int t5_reg_ranges[] = { 1246 0x1008, 0x10c0, 1247 0x10cc, 0x10f8, 1248 0x1100, 0x1100, 1249 0x110c, 0x1148, 1250 0x1180, 0x1184, 1251 0x1190, 0x1194, 1252 0x11a0, 0x11a4, 1253 0x11b0, 0x11b4, 1254 0x11fc, 0x123c, 1255 0x1280, 0x173c, 1256 0x1800, 0x18fc, 1257 0x3000, 0x3028, 1258 0x3060, 0x30b0, 1259 0x30b8, 0x30d8, 1260 0x30e0, 0x30fc, 1261 0x3140, 0x357c, 1262 0x35a8, 0x35cc, 1263 0x35ec, 0x35ec, 1264 0x3600, 0x5624, 1265 0x56cc, 0x56ec, 1266 0x56f4, 0x5720, 1267 0x5728, 0x575c, 1268 0x580c, 0x5814, 1269 0x5890, 0x589c, 1270 0x58a4, 0x58ac, 1271 0x58b8, 0x58bc, 1272 0x5940, 0x59c8, 1273 0x59d0, 0x59dc, 1274 0x59fc, 0x5a18, 1275 0x5a60, 0x5a70, 1276 0x5a80, 0x5a9c, 1277 0x5b94, 0x5bfc, 1278 0x6000, 0x6020, 1279 0x6028, 0x6040, 1280 0x6058, 0x609c, 1281 0x60a8, 0x614c, 1282 0x7700, 0x7798, 1283 0x77c0, 0x78fc, 1284 0x7b00, 0x7b58, 1285 0x7b60, 0x7b84, 1286 0x7b8c, 0x7c54, 1287 0x7d00, 0x7d38, 1288 0x7d40, 0x7d80, 1289 0x7d8c, 0x7ddc, 1290 0x7de4, 0x7e04, 1291 0x7e10, 0x7e1c, 1292 0x7e24, 0x7e38, 1293 0x7e40, 0x7e44, 1294 0x7e4c, 0x7e78, 1295 0x7e80, 0x7edc, 1296 0x7ee8, 0x7efc, 1297 0x8dc0, 0x8de0, 1298 0x8df8, 0x8e04, 1299 0x8e10, 0x8e84, 1300 0x8ea0, 0x8f84, 1301 0x8fc0, 0x9058, 1302 0x9060, 0x9060, 1303 0x9068, 0x90f8, 1304 0x9400, 0x9408, 1305 0x9410, 0x9470, 1306 0x9600, 0x9600, 1307 0x9608, 0x9638, 1308 0x9640, 0x96f4, 1309 0x9800, 0x9808, 1310 0x9820, 0x983c, 1311 0x9850, 0x9864, 1312 0x9c00, 0x9c6c, 1313 0x9c80, 0x9cec, 1314 0x9d00, 0x9d6c, 1315 0x9d80, 0x9dec, 1316 0x9e00, 0x9e6c, 1317 0x9e80, 0x9eec, 1318 0x9f00, 0x9f6c, 1319 0x9f80, 0xa020, 1320 0xd004, 0xd004, 1321 0xd010, 0xd03c, 1322 0xdfc0, 0xdfe0, 1323 0xe000, 0x1106c, 1324 0x11074, 0x11088, 1325 0x1109c, 0x1117c, 1326 0x11190, 0x11204, 1327 0x19040, 0x1906c, 1328 0x19078, 0x19080, 1329 0x1908c, 0x190e8, 1330 0x190f0, 0x190f8, 1331 0x19100, 0x19110, 1332 0x19120, 0x19124, 1333 0x19150, 0x19194, 1334 0x1919c, 0x191b0, 1335 0x191d0, 0x191e8, 1336 0x19238, 0x19290, 1337 0x193f8, 0x19428, 1338 0x19430, 0x19444, 1339 0x1944c, 0x1946c, 1340 0x19474, 0x19474, 1341 0x19490, 0x194cc, 1342 0x194f0, 0x194f8, 1343 0x19c00, 0x19c08, 1344 0x19c10, 0x19c60, 1345 0x19c94, 0x19ce4, 1346 0x19cf0, 0x19d40, 1347 0x19d50, 0x19d94, 1348 0x19da0, 0x19de8, 1349 0x19df0, 0x19e10, 1350 0x19e50, 0x19e90, 1351 0x19ea0, 0x19f24, 1352 0x19f34, 0x19f34, 1353 0x19f40, 0x19f50, 1354 0x19f90, 0x19fb4, 1355 0x19fc4, 0x19fe4, 1356 0x1a000, 0x1a004, 1357 0x1a010, 0x1a06c, 1358 0x1a0b0, 0x1a0e4, 1359 0x1a0ec, 0x1a0f8, 1360 0x1a100, 0x1a108, 1361 0x1a114, 0x1a120, 1362 0x1a128, 0x1a130, 1363 0x1a138, 0x1a138, 1364 0x1a190, 0x1a1c4, 1365 0x1a1fc, 0x1a1fc, 1366 0x1e008, 0x1e00c, 1367 0x1e040, 0x1e044, 1368 0x1e04c, 0x1e04c, 1369 0x1e284, 0x1e290, 1370 0x1e2c0, 0x1e2c0, 1371 0x1e2e0, 0x1e2e0, 1372 0x1e300, 0x1e384, 1373 0x1e3c0, 0x1e3c8, 1374 0x1e408, 0x1e40c, 1375 0x1e440, 0x1e444, 1376 0x1e44c, 0x1e44c, 1377 0x1e684, 0x1e690, 1378 0x1e6c0, 0x1e6c0, 1379 0x1e6e0, 0x1e6e0, 1380 0x1e700, 0x1e784, 1381 0x1e7c0, 0x1e7c8, 1382 0x1e808, 0x1e80c, 1383 0x1e840, 0x1e844, 1384 0x1e84c, 0x1e84c, 1385 0x1ea84, 0x1ea90, 1386 0x1eac0, 0x1eac0, 1387 0x1eae0, 0x1eae0, 1388 0x1eb00, 0x1eb84, 1389 0x1ebc0, 0x1ebc8, 1390 0x1ec08, 0x1ec0c, 1391 0x1ec40, 0x1ec44, 1392 0x1ec4c, 0x1ec4c, 1393 0x1ee84, 0x1ee90, 1394 0x1eec0, 0x1eec0, 1395 0x1eee0, 0x1eee0, 1396 0x1ef00, 0x1ef84, 1397 0x1efc0, 0x1efc8, 1398 0x1f008, 0x1f00c, 1399 0x1f040, 0x1f044, 1400 0x1f04c, 0x1f04c, 1401 0x1f284, 0x1f290, 1402 0x1f2c0, 0x1f2c0, 1403 0x1f2e0, 0x1f2e0, 1404 0x1f300, 0x1f384, 1405 0x1f3c0, 0x1f3c8, 1406 0x1f408, 0x1f40c, 1407 0x1f440, 0x1f444, 1408 0x1f44c, 0x1f44c, 1409 0x1f684, 0x1f690, 1410 0x1f6c0, 0x1f6c0, 1411 0x1f6e0, 0x1f6e0, 1412 0x1f700, 0x1f784, 1413 0x1f7c0, 0x1f7c8, 1414 0x1f808, 0x1f80c, 1415 0x1f840, 0x1f844, 1416 0x1f84c, 0x1f84c, 1417 0x1fa84, 0x1fa90, 1418 0x1fac0, 0x1fac0, 1419 0x1fae0, 0x1fae0, 1420 0x1fb00, 0x1fb84, 1421 0x1fbc0, 0x1fbc8, 1422 0x1fc08, 0x1fc0c, 1423 0x1fc40, 0x1fc44, 1424 0x1fc4c, 0x1fc4c, 1425 0x1fe84, 0x1fe90, 1426 0x1fec0, 0x1fec0, 1427 0x1fee0, 0x1fee0, 1428 0x1ff00, 0x1ff84, 1429 0x1ffc0, 0x1ffc8, 1430 0x30000, 0x30030, 1431 0x30100, 0x30144, 1432 0x30190, 0x301a0, 1433 0x301a8, 0x301b8, 1434 0x301c4, 0x301c8, 1435 0x301d0, 0x301d0, 1436 0x30200, 0x30318, 1437 0x30400, 0x304b4, 1438 0x304c0, 0x3052c, 1439 0x30540, 0x3061c, 1440 0x30800, 0x30828, 1441 0x30834, 0x30834, 1442 0x308c0, 0x30908, 1443 0x30910, 0x309ac, 1444 0x30a00, 0x30a14, 1445 0x30a1c, 0x30a2c, 1446 0x30a44, 0x30a50, 1447 0x30a74, 0x30a74, 1448 0x30a7c, 0x30afc, 1449 0x30b08, 0x30c24, 1450 0x30d00, 0x30d00, 1451 0x30d08, 0x30d14, 1452 0x30d1c, 0x30d20, 1453 0x30d3c, 0x30d3c, 1454 0x30d48, 0x30d50, 1455 0x31200, 0x3120c, 1456 0x31220, 0x31220, 1457 0x31240, 0x31240, 1458 0x31600, 0x3160c, 1459 0x31a00, 0x31a1c, 1460 0x31e00, 0x31e20, 1461 0x31e38, 0x31e3c, 1462 0x31e80, 0x31e80, 1463 0x31e88, 0x31ea8, 1464 0x31eb0, 0x31eb4, 1465 0x31ec8, 0x31ed4, 1466 0x31fb8, 0x32004, 1467 0x32200, 0x32200, 1468 0x32208, 0x32240, 1469 0x32248, 0x32280, 1470 0x32288, 0x322c0, 1471 0x322c8, 0x322fc, 1472 0x32600, 0x32630, 1473 0x32a00, 0x32abc, 1474 0x32b00, 0x32b10, 1475 0x32b20, 0x32b30, 1476 0x32b40, 0x32b50, 1477 0x32b60, 0x32b70, 1478 0x33000, 0x33028, 1479 0x33030, 0x33048, 1480 0x33060, 0x33068, 1481 0x33070, 0x3309c, 1482 0x330f0, 0x33128, 1483 0x33130, 0x33148, 1484 0x33160, 0x33168, 1485 0x33170, 0x3319c, 1486 0x331f0, 0x33238, 1487 0x33240, 0x33240, 1488 0x33248, 0x33250, 1489 0x3325c, 0x33264, 1490 0x33270, 0x332b8, 1491 0x332c0, 0x332e4, 1492 0x332f8, 0x33338, 1493 0x33340, 0x33340, 1494 0x33348, 0x33350, 1495 0x3335c, 0x33364, 1496 0x33370, 0x333b8, 1497 0x333c0, 0x333e4, 1498 0x333f8, 0x33428, 1499 0x33430, 0x33448, 1500 0x33460, 0x33468, 1501 0x33470, 0x3349c, 1502 0x334f0, 0x33528, 1503 0x33530, 0x33548, 1504 0x33560, 0x33568, 1505 0x33570, 0x3359c, 1506 0x335f0, 0x33638, 1507 0x33640, 0x33640, 1508 0x33648, 0x33650, 1509 0x3365c, 0x33664, 1510 0x33670, 0x336b8, 1511 0x336c0, 0x336e4, 1512 0x336f8, 0x33738, 1513 0x33740, 0x33740, 1514 0x33748, 0x33750, 1515 0x3375c, 0x33764, 1516 0x33770, 0x337b8, 1517 0x337c0, 0x337e4, 1518 0x337f8, 0x337fc, 1519 0x33814, 0x33814, 1520 0x3382c, 0x3382c, 1521 0x33880, 0x3388c, 1522 0x338e8, 0x338ec, 1523 0x33900, 0x33928, 1524 0x33930, 0x33948, 1525 0x33960, 0x33968, 1526 0x33970, 0x3399c, 1527 0x339f0, 0x33a38, 1528 0x33a40, 0x33a40, 1529 0x33a48, 0x33a50, 1530 0x33a5c, 0x33a64, 1531 0x33a70, 0x33ab8, 1532 0x33ac0, 0x33ae4, 1533 0x33af8, 0x33b10, 1534 0x33b28, 0x33b28, 1535 0x33b3c, 0x33b50, 1536 0x33bf0, 0x33c10, 1537 0x33c28, 0x33c28, 1538 0x33c3c, 0x33c50, 1539 0x33cf0, 0x33cfc, 1540 0x34000, 0x34030, 1541 0x34100, 0x34144, 1542 0x34190, 0x341a0, 1543 0x341a8, 0x341b8, 1544 0x341c4, 0x341c8, 1545 0x341d0, 0x341d0, 1546 0x34200, 0x34318, 1547 0x34400, 0x344b4, 1548 0x344c0, 0x3452c, 1549 0x34540, 0x3461c, 1550 0x34800, 0x34828, 1551 0x34834, 0x34834, 1552 0x348c0, 0x34908, 1553 0x34910, 0x349ac, 1554 0x34a00, 0x34a14, 1555 0x34a1c, 0x34a2c, 1556 0x34a44, 0x34a50, 1557 0x34a74, 0x34a74, 1558 0x34a7c, 0x34afc, 1559 0x34b08, 0x34c24, 1560 0x34d00, 0x34d00, 1561 0x34d08, 0x34d14, 1562 0x34d1c, 0x34d20, 1563 0x34d3c, 0x34d3c, 1564 0x34d48, 0x34d50, 1565 0x35200, 0x3520c, 1566 0x35220, 0x35220, 1567 0x35240, 0x35240, 1568 0x35600, 0x3560c, 1569 0x35a00, 0x35a1c, 1570 0x35e00, 0x35e20, 1571 0x35e38, 0x35e3c, 1572 0x35e80, 0x35e80, 1573 0x35e88, 0x35ea8, 1574 0x35eb0, 0x35eb4, 1575 0x35ec8, 0x35ed4, 1576 0x35fb8, 0x36004, 1577 0x36200, 0x36200, 1578 0x36208, 0x36240, 1579 0x36248, 0x36280, 1580 0x36288, 0x362c0, 1581 0x362c8, 0x362fc, 1582 0x36600, 0x36630, 1583 0x36a00, 0x36abc, 1584 0x36b00, 0x36b10, 1585 0x36b20, 0x36b30, 1586 0x36b40, 0x36b50, 1587 0x36b60, 0x36b70, 1588 0x37000, 0x37028, 1589 0x37030, 0x37048, 1590 0x37060, 0x37068, 1591 0x37070, 0x3709c, 1592 0x370f0, 0x37128, 1593 0x37130, 0x37148, 1594 0x37160, 0x37168, 1595 0x37170, 0x3719c, 1596 0x371f0, 0x37238, 1597 0x37240, 0x37240, 1598 0x37248, 0x37250, 1599 0x3725c, 0x37264, 1600 0x37270, 0x372b8, 1601 0x372c0, 0x372e4, 1602 0x372f8, 0x37338, 1603 0x37340, 0x37340, 1604 0x37348, 0x37350, 1605 0x3735c, 0x37364, 1606 0x37370, 0x373b8, 1607 0x373c0, 0x373e4, 1608 0x373f8, 0x37428, 1609 0x37430, 0x37448, 1610 0x37460, 0x37468, 1611 0x37470, 0x3749c, 1612 0x374f0, 0x37528, 1613 0x37530, 0x37548, 1614 0x37560, 0x37568, 1615 0x37570, 0x3759c, 1616 0x375f0, 0x37638, 1617 0x37640, 0x37640, 1618 0x37648, 0x37650, 1619 0x3765c, 0x37664, 1620 0x37670, 0x376b8, 1621 0x376c0, 0x376e4, 1622 0x376f8, 0x37738, 1623 0x37740, 0x37740, 1624 0x37748, 0x37750, 1625 0x3775c, 0x37764, 1626 0x37770, 0x377b8, 1627 0x377c0, 0x377e4, 1628 0x377f8, 0x377fc, 1629 0x37814, 0x37814, 1630 0x3782c, 0x3782c, 1631 0x37880, 0x3788c, 1632 0x378e8, 0x378ec, 1633 0x37900, 0x37928, 1634 0x37930, 0x37948, 1635 0x37960, 0x37968, 1636 0x37970, 0x3799c, 1637 0x379f0, 0x37a38, 1638 0x37a40, 0x37a40, 1639 0x37a48, 0x37a50, 1640 0x37a5c, 0x37a64, 1641 0x37a70, 0x37ab8, 1642 0x37ac0, 0x37ae4, 1643 0x37af8, 0x37b10, 1644 0x37b28, 0x37b28, 1645 0x37b3c, 0x37b50, 1646 0x37bf0, 0x37c10, 1647 0x37c28, 0x37c28, 1648 0x37c3c, 0x37c50, 1649 0x37cf0, 0x37cfc, 1650 0x38000, 0x38030, 1651 0x38100, 0x38144, 1652 0x38190, 0x381a0, 1653 0x381a8, 0x381b8, 1654 0x381c4, 0x381c8, 1655 0x381d0, 0x381d0, 1656 0x38200, 0x38318, 1657 0x38400, 0x384b4, 1658 0x384c0, 0x3852c, 1659 0x38540, 0x3861c, 1660 0x38800, 0x38828, 1661 0x38834, 0x38834, 1662 0x388c0, 0x38908, 1663 0x38910, 0x389ac, 1664 0x38a00, 0x38a14, 1665 0x38a1c, 0x38a2c, 1666 0x38a44, 0x38a50, 1667 0x38a74, 0x38a74, 1668 0x38a7c, 0x38afc, 1669 0x38b08, 0x38c24, 1670 0x38d00, 0x38d00, 1671 0x38d08, 0x38d14, 1672 0x38d1c, 0x38d20, 1673 0x38d3c, 0x38d3c, 1674 0x38d48, 0x38d50, 1675 0x39200, 0x3920c, 1676 0x39220, 0x39220, 1677 0x39240, 0x39240, 1678 0x39600, 0x3960c, 1679 0x39a00, 0x39a1c, 1680 0x39e00, 0x39e20, 1681 0x39e38, 0x39e3c, 1682 0x39e80, 0x39e80, 1683 0x39e88, 0x39ea8, 1684 0x39eb0, 0x39eb4, 1685 0x39ec8, 0x39ed4, 1686 0x39fb8, 0x3a004, 1687 0x3a200, 0x3a200, 1688 0x3a208, 0x3a240, 1689 0x3a248, 0x3a280, 1690 0x3a288, 0x3a2c0, 1691 0x3a2c8, 0x3a2fc, 1692 0x3a600, 0x3a630, 1693 0x3aa00, 0x3aabc, 1694 0x3ab00, 0x3ab10, 1695 0x3ab20, 0x3ab30, 1696 0x3ab40, 0x3ab50, 1697 0x3ab60, 0x3ab70, 1698 0x3b000, 0x3b028, 1699 0x3b030, 0x3b048, 1700 0x3b060, 0x3b068, 1701 0x3b070, 0x3b09c, 1702 0x3b0f0, 0x3b128, 1703 0x3b130, 0x3b148, 1704 0x3b160, 0x3b168, 1705 0x3b170, 0x3b19c, 1706 0x3b1f0, 0x3b238, 1707 0x3b240, 0x3b240, 1708 0x3b248, 0x3b250, 1709 0x3b25c, 0x3b264, 1710 0x3b270, 0x3b2b8, 1711 0x3b2c0, 0x3b2e4, 1712 0x3b2f8, 0x3b338, 1713 0x3b340, 0x3b340, 1714 0x3b348, 0x3b350, 1715 0x3b35c, 0x3b364, 1716 0x3b370, 0x3b3b8, 1717 0x3b3c0, 0x3b3e4, 1718 0x3b3f8, 0x3b428, 1719 0x3b430, 0x3b448, 1720 0x3b460, 0x3b468, 1721 0x3b470, 0x3b49c, 1722 0x3b4f0, 0x3b528, 1723 0x3b530, 0x3b548, 1724 0x3b560, 0x3b568, 1725 0x3b570, 0x3b59c, 1726 0x3b5f0, 0x3b638, 1727 0x3b640, 0x3b640, 1728 0x3b648, 0x3b650, 1729 0x3b65c, 0x3b664, 1730 0x3b670, 0x3b6b8, 1731 0x3b6c0, 0x3b6e4, 1732 0x3b6f8, 0x3b738, 1733 0x3b740, 0x3b740, 1734 0x3b748, 0x3b750, 1735 0x3b75c, 0x3b764, 1736 0x3b770, 0x3b7b8, 1737 0x3b7c0, 0x3b7e4, 1738 0x3b7f8, 0x3b7fc, 1739 0x3b814, 0x3b814, 1740 0x3b82c, 0x3b82c, 1741 0x3b880, 0x3b88c, 1742 0x3b8e8, 0x3b8ec, 1743 0x3b900, 0x3b928, 1744 0x3b930, 0x3b948, 1745 0x3b960, 0x3b968, 1746 0x3b970, 0x3b99c, 1747 0x3b9f0, 0x3ba38, 1748 0x3ba40, 0x3ba40, 1749 0x3ba48, 0x3ba50, 1750 0x3ba5c, 0x3ba64, 1751 0x3ba70, 0x3bab8, 1752 0x3bac0, 0x3bae4, 1753 0x3baf8, 0x3bb10, 1754 0x3bb28, 0x3bb28, 1755 0x3bb3c, 0x3bb50, 1756 0x3bbf0, 0x3bc10, 1757 0x3bc28, 0x3bc28, 1758 0x3bc3c, 0x3bc50, 1759 0x3bcf0, 0x3bcfc, 1760 0x3c000, 0x3c030, 1761 0x3c100, 0x3c144, 1762 0x3c190, 0x3c1a0, 1763 0x3c1a8, 0x3c1b8, 1764 0x3c1c4, 0x3c1c8, 1765 0x3c1d0, 0x3c1d0, 1766 0x3c200, 0x3c318, 1767 0x3c400, 0x3c4b4, 1768 0x3c4c0, 0x3c52c, 1769 0x3c540, 0x3c61c, 1770 0x3c800, 0x3c828, 1771 0x3c834, 0x3c834, 1772 0x3c8c0, 0x3c908, 1773 0x3c910, 0x3c9ac, 1774 0x3ca00, 0x3ca14, 1775 0x3ca1c, 0x3ca2c, 1776 0x3ca44, 0x3ca50, 1777 0x3ca74, 0x3ca74, 1778 0x3ca7c, 0x3cafc, 1779 0x3cb08, 0x3cc24, 1780 0x3cd00, 0x3cd00, 1781 0x3cd08, 0x3cd14, 1782 0x3cd1c, 0x3cd20, 1783 0x3cd3c, 0x3cd3c, 1784 0x3cd48, 0x3cd50, 1785 0x3d200, 0x3d20c, 1786 0x3d220, 0x3d220, 1787 0x3d240, 0x3d240, 1788 0x3d600, 0x3d60c, 1789 0x3da00, 0x3da1c, 1790 0x3de00, 0x3de20, 1791 0x3de38, 0x3de3c, 1792 0x3de80, 0x3de80, 1793 0x3de88, 0x3dea8, 1794 0x3deb0, 0x3deb4, 1795 0x3dec8, 0x3ded4, 1796 0x3dfb8, 0x3e004, 1797 0x3e200, 0x3e200, 1798 0x3e208, 0x3e240, 1799 0x3e248, 0x3e280, 1800 0x3e288, 0x3e2c0, 1801 0x3e2c8, 0x3e2fc, 1802 0x3e600, 0x3e630, 1803 0x3ea00, 0x3eabc, 1804 0x3eb00, 0x3eb10, 1805 0x3eb20, 0x3eb30, 1806 0x3eb40, 0x3eb50, 1807 0x3eb60, 0x3eb70, 1808 0x3f000, 0x3f028, 1809 0x3f030, 0x3f048, 1810 0x3f060, 0x3f068, 1811 0x3f070, 0x3f09c, 1812 0x3f0f0, 0x3f128, 1813 0x3f130, 0x3f148, 1814 0x3f160, 0x3f168, 1815 0x3f170, 0x3f19c, 1816 0x3f1f0, 0x3f238, 1817 0x3f240, 0x3f240, 1818 0x3f248, 0x3f250, 1819 0x3f25c, 0x3f264, 1820 0x3f270, 0x3f2b8, 1821 0x3f2c0, 0x3f2e4, 1822 0x3f2f8, 0x3f338, 1823 0x3f340, 0x3f340, 1824 0x3f348, 0x3f350, 1825 0x3f35c, 0x3f364, 1826 0x3f370, 0x3f3b8, 1827 0x3f3c0, 0x3f3e4, 1828 0x3f3f8, 0x3f428, 1829 0x3f430, 0x3f448, 1830 0x3f460, 0x3f468, 1831 0x3f470, 0x3f49c, 1832 0x3f4f0, 0x3f528, 1833 0x3f530, 0x3f548, 1834 0x3f560, 0x3f568, 1835 0x3f570, 0x3f59c, 1836 0x3f5f0, 0x3f638, 1837 0x3f640, 0x3f640, 1838 0x3f648, 0x3f650, 1839 0x3f65c, 0x3f664, 1840 0x3f670, 0x3f6b8, 1841 0x3f6c0, 0x3f6e4, 1842 0x3f6f8, 0x3f738, 1843 0x3f740, 0x3f740, 1844 0x3f748, 0x3f750, 1845 0x3f75c, 0x3f764, 1846 0x3f770, 0x3f7b8, 1847 0x3f7c0, 0x3f7e4, 1848 0x3f7f8, 0x3f7fc, 1849 0x3f814, 0x3f814, 1850 0x3f82c, 0x3f82c, 1851 0x3f880, 0x3f88c, 1852 0x3f8e8, 0x3f8ec, 1853 0x3f900, 0x3f928, 1854 0x3f930, 0x3f948, 1855 0x3f960, 0x3f968, 1856 0x3f970, 0x3f99c, 1857 0x3f9f0, 0x3fa38, 1858 0x3fa40, 0x3fa40, 1859 0x3fa48, 0x3fa50, 1860 0x3fa5c, 0x3fa64, 1861 0x3fa70, 0x3fab8, 1862 0x3fac0, 0x3fae4, 1863 0x3faf8, 0x3fb10, 1864 0x3fb28, 0x3fb28, 1865 0x3fb3c, 0x3fb50, 1866 0x3fbf0, 0x3fc10, 1867 0x3fc28, 0x3fc28, 1868 0x3fc3c, 0x3fc50, 1869 0x3fcf0, 0x3fcfc, 1870 0x40000, 0x4000c, 1871 0x40040, 0x40050, 1872 0x40060, 0x40068, 1873 0x4007c, 0x4008c, 1874 0x40094, 0x400b0, 1875 0x400c0, 0x40144, 1876 0x40180, 0x4018c, 1877 0x40200, 0x40254, 1878 0x40260, 0x40264, 1879 0x40270, 0x40288, 1880 0x40290, 0x40298, 1881 0x402ac, 0x402c8, 1882 0x402d0, 0x402e0, 1883 0x402f0, 0x402f0, 1884 0x40300, 0x4033c, 1885 0x403f8, 0x403fc, 1886 0x41304, 0x413c4, 1887 0x41400, 0x4140c, 1888 0x41414, 0x4141c, 1889 0x41480, 0x414d0, 1890 0x44000, 0x44054, 1891 0x4405c, 0x44078, 1892 0x440c0, 0x44174, 1893 0x44180, 0x441ac, 1894 0x441b4, 0x441b8, 1895 0x441c0, 0x44254, 1896 0x4425c, 0x44278, 1897 0x442c0, 0x44374, 1898 0x44380, 0x443ac, 1899 0x443b4, 0x443b8, 1900 0x443c0, 0x44454, 1901 0x4445c, 0x44478, 1902 0x444c0, 0x44574, 1903 0x44580, 0x445ac, 1904 0x445b4, 0x445b8, 1905 0x445c0, 0x44654, 1906 0x4465c, 0x44678, 1907 0x446c0, 0x44774, 1908 0x44780, 0x447ac, 1909 0x447b4, 0x447b8, 1910 0x447c0, 0x44854, 1911 0x4485c, 0x44878, 1912 0x448c0, 0x44974, 1913 0x44980, 0x449ac, 1914 0x449b4, 0x449b8, 1915 0x449c0, 0x449fc, 1916 0x45000, 0x45004, 1917 0x45010, 0x45030, 1918 0x45040, 0x45060, 1919 0x45068, 0x45068, 1920 0x45080, 0x45084, 1921 0x450a0, 0x450b0, 1922 0x45200, 0x45204, 1923 0x45210, 0x45230, 1924 0x45240, 0x45260, 1925 0x45268, 0x45268, 1926 0x45280, 0x45284, 1927 0x452a0, 0x452b0, 1928 0x460c0, 0x460e4, 1929 0x47000, 0x4703c, 1930 0x47044, 0x4708c, 1931 0x47200, 0x47250, 1932 0x47400, 0x47408, 1933 0x47414, 0x47420, 1934 0x47600, 0x47618, 1935 0x47800, 0x47814, 1936 0x48000, 0x4800c, 1937 0x48040, 0x48050, 1938 0x48060, 0x48068, 1939 0x4807c, 0x4808c, 1940 0x48094, 0x480b0, 1941 0x480c0, 0x48144, 1942 0x48180, 0x4818c, 1943 0x48200, 0x48254, 1944 0x48260, 0x48264, 1945 0x48270, 0x48288, 1946 0x48290, 0x48298, 1947 0x482ac, 0x482c8, 1948 0x482d0, 0x482e0, 1949 0x482f0, 0x482f0, 1950 0x48300, 0x4833c, 1951 0x483f8, 0x483fc, 1952 0x49304, 0x493c4, 1953 0x49400, 0x4940c, 1954 0x49414, 0x4941c, 1955 0x49480, 0x494d0, 1956 0x4c000, 0x4c054, 1957 0x4c05c, 0x4c078, 1958 0x4c0c0, 0x4c174, 1959 0x4c180, 0x4c1ac, 1960 0x4c1b4, 0x4c1b8, 1961 0x4c1c0, 0x4c254, 1962 0x4c25c, 0x4c278, 1963 0x4c2c0, 0x4c374, 1964 0x4c380, 0x4c3ac, 1965 0x4c3b4, 0x4c3b8, 1966 0x4c3c0, 0x4c454, 1967 0x4c45c, 0x4c478, 1968 0x4c4c0, 0x4c574, 1969 0x4c580, 0x4c5ac, 1970 0x4c5b4, 0x4c5b8, 1971 0x4c5c0, 0x4c654, 1972 0x4c65c, 0x4c678, 1973 0x4c6c0, 0x4c774, 1974 0x4c780, 0x4c7ac, 1975 0x4c7b4, 0x4c7b8, 1976 0x4c7c0, 0x4c854, 1977 0x4c85c, 0x4c878, 1978 0x4c8c0, 0x4c974, 1979 0x4c980, 0x4c9ac, 1980 0x4c9b4, 0x4c9b8, 1981 0x4c9c0, 0x4c9fc, 1982 0x4d000, 0x4d004, 1983 0x4d010, 0x4d030, 1984 0x4d040, 0x4d060, 1985 0x4d068, 0x4d068, 1986 0x4d080, 0x4d084, 1987 0x4d0a0, 0x4d0b0, 1988 0x4d200, 0x4d204, 1989 0x4d210, 0x4d230, 1990 0x4d240, 0x4d260, 1991 0x4d268, 0x4d268, 1992 0x4d280, 0x4d284, 1993 0x4d2a0, 0x4d2b0, 1994 0x4e0c0, 0x4e0e4, 1995 0x4f000, 0x4f03c, 1996 0x4f044, 0x4f08c, 1997 0x4f200, 0x4f250, 1998 0x4f400, 0x4f408, 1999 0x4f414, 0x4f420, 2000 0x4f600, 0x4f618, 2001 0x4f800, 0x4f814, 2002 0x50000, 0x50084, 2003 0x50090, 0x500cc, 2004 0x50400, 0x50400, 2005 0x50800, 0x50884, 2006 0x50890, 0x508cc, 2007 0x50c00, 0x50c00, 2008 0x51000, 0x5101c, 2009 0x51300, 0x51308, 2010 }; 2011 2012 static const unsigned int t5vf_reg_ranges[] = { 2013 VF_SGE_REG(A_SGE_VF_KDOORBELL), VF_SGE_REG(A_SGE_VF_GTS), 2014 VF_MPS_REG(A_MPS_VF_CTL), 2015 VF_MPS_REG(A_MPS_VF_STAT_RX_VF_ERR_FRAMES_H), 2016 VF_PL_REG(A_PL_VF_WHOAMI), VF_PL_REG(A_PL_VF_REVISION), 2017 VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_CTRL), 2018 VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_STATUS), 2019 FW_T4VF_MBDATA_BASE_ADDR, 2020 FW_T4VF_MBDATA_BASE_ADDR + 2021 ((NUM_CIM_PF_MAILBOX_DATA_INSTANCES - 1) * 4), 2022 }; 2023 2024 static const unsigned int t6_reg_ranges[] = { 2025 0x1008, 0x101c, 2026 0x1024, 0x10a8, 2027 0x10b4, 0x10f8, 2028 0x1100, 0x1114, 2029 0x111c, 0x112c, 2030 0x1138, 0x113c, 2031 0x1144, 0x114c, 2032 0x1180, 0x1184, 2033 0x1190, 0x1194, 2034 0x11a0, 0x11a4, 2035 0x11b0, 0x11b4, 2036 0x11fc, 0x1274, 2037 0x1280, 0x133c, 2038 0x1800, 0x18fc, 2039 0x3000, 0x302c, 2040 0x3060, 0x30b0, 2041 0x30b8, 0x30d8, 2042 0x30e0, 0x30fc, 2043 0x3140, 0x357c, 2044 0x35a8, 0x35cc, 2045 0x35ec, 0x35ec, 2046 0x3600, 0x5624, 2047 0x56cc, 0x56ec, 2048 0x56f4, 0x5720, 2049 0x5728, 0x575c, 2050 0x580c, 0x5814, 2051 0x5890, 0x589c, 2052 0x58a4, 0x58ac, 2053 0x58b8, 0x58bc, 2054 0x5940, 0x595c, 2055 0x5980, 0x598c, 2056 0x59b0, 0x59c8, 2057 0x59d0, 0x59dc, 2058 0x59fc, 0x5a18, 2059 0x5a60, 0x5a6c, 2060 0x5a80, 0x5a8c, 2061 0x5a94, 0x5a9c, 2062 0x5b94, 0x5bfc, 2063 0x5c10, 0x5e48, 2064 0x5e50, 0x5e94, 2065 0x5ea0, 0x5eb0, 2066 0x5ec0, 0x5ec0, 2067 0x5ec8, 0x5ed0, 2068 0x5ee0, 0x5ee0, 2069 0x5ef0, 0x5ef0, 2070 0x5f00, 0x5f00, 2071 0x6000, 0x6020, 2072 0x6028, 0x6040, 2073 0x6058, 0x609c, 2074 0x60a8, 0x619c, 2075 0x7700, 0x7798, 2076 0x77c0, 0x7880, 2077 0x78cc, 0x78fc, 2078 0x7b00, 0x7b58, 2079 0x7b60, 0x7b84, 2080 0x7b8c, 0x7c54, 2081 0x7d00, 0x7d38, 2082 0x7d40, 0x7d84, 2083 0x7d8c, 0x7ddc, 2084 0x7de4, 0x7e04, 2085 0x7e10, 0x7e1c, 2086 0x7e24, 0x7e38, 2087 0x7e40, 0x7e44, 2088 0x7e4c, 0x7e78, 2089 0x7e80, 0x7edc, 2090 0x7ee8, 0x7efc, 2091 0x8dc0, 0x8de4, 2092 0x8df8, 0x8e04, 2093 0x8e10, 0x8e84, 2094 0x8ea0, 0x8f88, 2095 0x8fb8, 0x9058, 2096 0x9060, 0x9060, 2097 0x9068, 0x90f8, 2098 0x9100, 0x9124, 2099 0x9400, 0x9470, 2100 0x9600, 0x9600, 2101 0x9608, 0x9638, 2102 0x9640, 0x9704, 2103 0x9710, 0x971c, 2104 0x9800, 0x9808, 2105 0x9820, 0x983c, 2106 0x9850, 0x9864, 2107 0x9c00, 0x9c6c, 2108 0x9c80, 0x9cec, 2109 0x9d00, 0x9d6c, 2110 0x9d80, 0x9dec, 2111 0x9e00, 0x9e6c, 2112 0x9e80, 0x9eec, 2113 0x9f00, 0x9f6c, 2114 0x9f80, 0xa020, 2115 0xd004, 0xd03c, 2116 0xd100, 0xd118, 2117 0xd200, 0xd214, 2118 0xd220, 0xd234, 2119 0xd240, 0xd254, 2120 0xd260, 0xd274, 2121 0xd280, 0xd294, 2122 0xd2a0, 0xd2b4, 2123 0xd2c0, 0xd2d4, 2124 0xd2e0, 0xd2f4, 2125 0xd300, 0xd31c, 2126 0xdfc0, 0xdfe0, 2127 0xe000, 0xf008, 2128 0xf010, 0xf018, 2129 0xf020, 0xf028, 2130 0x11000, 0x11014, 2131 0x11048, 0x1106c, 2132 0x11074, 0x11088, 2133 0x11098, 0x11120, 2134 0x1112c, 0x1117c, 2135 0x11190, 0x112e0, 2136 0x11300, 0x1130c, 2137 0x12000, 0x1206c, 2138 0x19040, 0x1906c, 2139 0x19078, 0x19080, 2140 0x1908c, 0x190e8, 2141 0x190f0, 0x190f8, 2142 0x19100, 0x19110, 2143 0x19120, 0x19124, 2144 0x19150, 0x19194, 2145 0x1919c, 0x191b0, 2146 0x191d0, 0x191e8, 2147 0x19238, 0x19290, 2148 0x192a4, 0x192b0, 2149 0x192bc, 0x192bc, 2150 0x19348, 0x1934c, 2151 0x193f8, 0x19418, 2152 0x19420, 0x19428, 2153 0x19430, 0x19444, 2154 0x1944c, 0x1946c, 2155 0x19474, 0x19474, 2156 0x19490, 0x194cc, 2157 0x194f0, 0x194f8, 2158 0x19c00, 0x19c48, 2159 0x19c50, 0x19c80, 2160 0x19c94, 0x19c98, 2161 0x19ca0, 0x19cbc, 2162 0x19ce4, 0x19ce4, 2163 0x19cf0, 0x19cf8, 2164 0x19d00, 0x19d28, 2165 0x19d50, 0x19d78, 2166 0x19d94, 0x19d98, 2167 0x19da0, 0x19dc8, 2168 0x19df0, 0x19e10, 2169 0x19e50, 0x19e6c, 2170 0x19ea0, 0x19ebc, 2171 0x19ec4, 0x19ef4, 2172 0x19f04, 0x19f2c, 2173 0x19f34, 0x19f34, 2174 0x19f40, 0x19f50, 2175 0x19f90, 0x19fac, 2176 0x19fc4, 0x19fc8, 2177 0x19fd0, 0x19fe4, 2178 0x1a000, 0x1a004, 2179 0x1a010, 0x1a06c, 2180 0x1a0b0, 0x1a0e4, 2181 0x1a0ec, 0x1a0f8, 2182 0x1a100, 0x1a108, 2183 0x1a114, 0x1a120, 2184 0x1a128, 0x1a130, 2185 0x1a138, 0x1a138, 2186 0x1a190, 0x1a1c4, 2187 0x1a1fc, 0x1a1fc, 2188 0x1e008, 0x1e00c, 2189 0x1e040, 0x1e044, 2190 0x1e04c, 0x1e04c, 2191 0x1e284, 0x1e290, 2192 0x1e2c0, 0x1e2c0, 2193 0x1e2e0, 0x1e2e0, 2194 0x1e300, 0x1e384, 2195 0x1e3c0, 0x1e3c8, 2196 0x1e408, 0x1e40c, 2197 0x1e440, 0x1e444, 2198 0x1e44c, 0x1e44c, 2199 0x1e684, 0x1e690, 2200 0x1e6c0, 0x1e6c0, 2201 0x1e6e0, 0x1e6e0, 2202 0x1e700, 0x1e784, 2203 0x1e7c0, 0x1e7c8, 2204 0x1e808, 0x1e80c, 2205 0x1e840, 0x1e844, 2206 0x1e84c, 0x1e84c, 2207 0x1ea84, 0x1ea90, 2208 0x1eac0, 0x1eac0, 2209 0x1eae0, 0x1eae0, 2210 0x1eb00, 0x1eb84, 2211 0x1ebc0, 0x1ebc8, 2212 0x1ec08, 0x1ec0c, 2213 0x1ec40, 0x1ec44, 2214 0x1ec4c, 0x1ec4c, 2215 0x1ee84, 0x1ee90, 2216 0x1eec0, 0x1eec0, 2217 0x1eee0, 0x1eee0, 2218 0x1ef00, 0x1ef84, 2219 0x1efc0, 0x1efc8, 2220 0x1f008, 0x1f00c, 2221 0x1f040, 0x1f044, 2222 0x1f04c, 0x1f04c, 2223 0x1f284, 0x1f290, 2224 0x1f2c0, 0x1f2c0, 2225 0x1f2e0, 0x1f2e0, 2226 0x1f300, 0x1f384, 2227 0x1f3c0, 0x1f3c8, 2228 0x1f408, 0x1f40c, 2229 0x1f440, 0x1f444, 2230 0x1f44c, 0x1f44c, 2231 0x1f684, 0x1f690, 2232 0x1f6c0, 0x1f6c0, 2233 0x1f6e0, 0x1f6e0, 2234 0x1f700, 0x1f784, 2235 0x1f7c0, 0x1f7c8, 2236 0x1f808, 0x1f80c, 2237 0x1f840, 0x1f844, 2238 0x1f84c, 0x1f84c, 2239 0x1fa84, 0x1fa90, 2240 0x1fac0, 0x1fac0, 2241 0x1fae0, 0x1fae0, 2242 0x1fb00, 0x1fb84, 2243 0x1fbc0, 0x1fbc8, 2244 0x1fc08, 0x1fc0c, 2245 0x1fc40, 0x1fc44, 2246 0x1fc4c, 0x1fc4c, 2247 0x1fe84, 0x1fe90, 2248 0x1fec0, 0x1fec0, 2249 0x1fee0, 0x1fee0, 2250 0x1ff00, 0x1ff84, 2251 0x1ffc0, 0x1ffc8, 2252 0x30000, 0x30030, 2253 0x30100, 0x30168, 2254 0x30190, 0x301a0, 2255 0x301a8, 0x301b8, 2256 0x301c4, 0x301c8, 2257 0x301d0, 0x301d0, 2258 0x30200, 0x30320, 2259 0x30400, 0x304b4, 2260 0x304c0, 0x3052c, 2261 0x30540, 0x3061c, 2262 0x30800, 0x308a0, 2263 0x308c0, 0x30908, 2264 0x30910, 0x309b8, 2265 0x30a00, 0x30a04, 2266 0x30a0c, 0x30a14, 2267 0x30a1c, 0x30a2c, 2268 0x30a44, 0x30a50, 2269 0x30a74, 0x30a74, 2270 0x30a7c, 0x30afc, 2271 0x30b08, 0x30c24, 2272 0x30d00, 0x30d14, 2273 0x30d1c, 0x30d3c, 2274 0x30d44, 0x30d4c, 2275 0x30d54, 0x30d74, 2276 0x30d7c, 0x30d7c, 2277 0x30de0, 0x30de0, 2278 0x30e00, 0x30ed4, 2279 0x30f00, 0x30fa4, 2280 0x30fc0, 0x30fc4, 2281 0x31000, 0x31004, 2282 0x31080, 0x310fc, 2283 0x31208, 0x31220, 2284 0x3123c, 0x31254, 2285 0x31300, 0x31300, 2286 0x31308, 0x3131c, 2287 0x31338, 0x3133c, 2288 0x31380, 0x31380, 2289 0x31388, 0x313a8, 2290 0x313b4, 0x313b4, 2291 0x31400, 0x31420, 2292 0x31438, 0x3143c, 2293 0x31480, 0x31480, 2294 0x314a8, 0x314a8, 2295 0x314b0, 0x314b4, 2296 0x314c8, 0x314d4, 2297 0x31a40, 0x31a4c, 2298 0x31af0, 0x31b20, 2299 0x31b38, 0x31b3c, 2300 0x31b80, 0x31b80, 2301 0x31ba8, 0x31ba8, 2302 0x31bb0, 0x31bb4, 2303 0x31bc8, 0x31bd4, 2304 0x32140, 0x3218c, 2305 0x321f0, 0x321f4, 2306 0x32200, 0x32200, 2307 0x32218, 0x32218, 2308 0x32400, 0x32400, 2309 0x32408, 0x3241c, 2310 0x32618, 0x32620, 2311 0x32664, 0x32664, 2312 0x326a8, 0x326a8, 2313 0x326ec, 0x326ec, 2314 0x32a00, 0x32abc, 2315 0x32b00, 0x32b18, 2316 0x32b20, 0x32b38, 2317 0x32b40, 0x32b58, 2318 0x32b60, 0x32b78, 2319 0x32c00, 0x32c00, 2320 0x32c08, 0x32c3c, 2321 0x33000, 0x3302c, 2322 0x33034, 0x33050, 2323 0x33058, 0x33058, 2324 0x33060, 0x3308c, 2325 0x3309c, 0x330ac, 2326 0x330c0, 0x330c0, 2327 0x330c8, 0x330d0, 2328 0x330d8, 0x330e0, 2329 0x330ec, 0x3312c, 2330 0x33134, 0x33150, 2331 0x33158, 0x33158, 2332 0x33160, 0x3318c, 2333 0x3319c, 0x331ac, 2334 0x331c0, 0x331c0, 2335 0x331c8, 0x331d0, 2336 0x331d8, 0x331e0, 2337 0x331ec, 0x33290, 2338 0x33298, 0x332c4, 2339 0x332e4, 0x33390, 2340 0x33398, 0x333c4, 2341 0x333e4, 0x3342c, 2342 0x33434, 0x33450, 2343 0x33458, 0x33458, 2344 0x33460, 0x3348c, 2345 0x3349c, 0x334ac, 2346 0x334c0, 0x334c0, 2347 0x334c8, 0x334d0, 2348 0x334d8, 0x334e0, 2349 0x334ec, 0x3352c, 2350 0x33534, 0x33550, 2351 0x33558, 0x33558, 2352 0x33560, 0x3358c, 2353 0x3359c, 0x335ac, 2354 0x335c0, 0x335c0, 2355 0x335c8, 0x335d0, 2356 0x335d8, 0x335e0, 2357 0x335ec, 0x33690, 2358 0x33698, 0x336c4, 2359 0x336e4, 0x33790, 2360 0x33798, 0x337c4, 2361 0x337e4, 0x337fc, 2362 0x33814, 0x33814, 2363 0x33854, 0x33868, 2364 0x33880, 0x3388c, 2365 0x338c0, 0x338d0, 2366 0x338e8, 0x338ec, 2367 0x33900, 0x3392c, 2368 0x33934, 0x33950, 2369 0x33958, 0x33958, 2370 0x33960, 0x3398c, 2371 0x3399c, 0x339ac, 2372 0x339c0, 0x339c0, 2373 0x339c8, 0x339d0, 2374 0x339d8, 0x339e0, 2375 0x339ec, 0x33a90, 2376 0x33a98, 0x33ac4, 2377 0x33ae4, 0x33b10, 2378 0x33b24, 0x33b28, 2379 0x33b38, 0x33b50, 2380 0x33bf0, 0x33c10, 2381 0x33c24, 0x33c28, 2382 0x33c38, 0x33c50, 2383 0x33cf0, 0x33cfc, 2384 0x34000, 0x34030, 2385 0x34100, 0x34168, 2386 0x34190, 0x341a0, 2387 0x341a8, 0x341b8, 2388 0x341c4, 0x341c8, 2389 0x341d0, 0x341d0, 2390 0x34200, 0x34320, 2391 0x34400, 0x344b4, 2392 0x344c0, 0x3452c, 2393 0x34540, 0x3461c, 2394 0x34800, 0x348a0, 2395 0x348c0, 0x34908, 2396 0x34910, 0x349b8, 2397 0x34a00, 0x34a04, 2398 0x34a0c, 0x34a14, 2399 0x34a1c, 0x34a2c, 2400 0x34a44, 0x34a50, 2401 0x34a74, 0x34a74, 2402 0x34a7c, 0x34afc, 2403 0x34b08, 0x34c24, 2404 0x34d00, 0x34d14, 2405 0x34d1c, 0x34d3c, 2406 0x34d44, 0x34d4c, 2407 0x34d54, 0x34d74, 2408 0x34d7c, 0x34d7c, 2409 0x34de0, 0x34de0, 2410 0x34e00, 0x34ed4, 2411 0x34f00, 0x34fa4, 2412 0x34fc0, 0x34fc4, 2413 0x35000, 0x35004, 2414 0x35080, 0x350fc, 2415 0x35208, 0x35220, 2416 0x3523c, 0x35254, 2417 0x35300, 0x35300, 2418 0x35308, 0x3531c, 2419 0x35338, 0x3533c, 2420 0x35380, 0x35380, 2421 0x35388, 0x353a8, 2422 0x353b4, 0x353b4, 2423 0x35400, 0x35420, 2424 0x35438, 0x3543c, 2425 0x35480, 0x35480, 2426 0x354a8, 0x354a8, 2427 0x354b0, 0x354b4, 2428 0x354c8, 0x354d4, 2429 0x35a40, 0x35a4c, 2430 0x35af0, 0x35b20, 2431 0x35b38, 0x35b3c, 2432 0x35b80, 0x35b80, 2433 0x35ba8, 0x35ba8, 2434 0x35bb0, 0x35bb4, 2435 0x35bc8, 0x35bd4, 2436 0x36140, 0x3618c, 2437 0x361f0, 0x361f4, 2438 0x36200, 0x36200, 2439 0x36218, 0x36218, 2440 0x36400, 0x36400, 2441 0x36408, 0x3641c, 2442 0x36618, 0x36620, 2443 0x36664, 0x36664, 2444 0x366a8, 0x366a8, 2445 0x366ec, 0x366ec, 2446 0x36a00, 0x36abc, 2447 0x36b00, 0x36b18, 2448 0x36b20, 0x36b38, 2449 0x36b40, 0x36b58, 2450 0x36b60, 0x36b78, 2451 0x36c00, 0x36c00, 2452 0x36c08, 0x36c3c, 2453 0x37000, 0x3702c, 2454 0x37034, 0x37050, 2455 0x37058, 0x37058, 2456 0x37060, 0x3708c, 2457 0x3709c, 0x370ac, 2458 0x370c0, 0x370c0, 2459 0x370c8, 0x370d0, 2460 0x370d8, 0x370e0, 2461 0x370ec, 0x3712c, 2462 0x37134, 0x37150, 2463 0x37158, 0x37158, 2464 0x37160, 0x3718c, 2465 0x3719c, 0x371ac, 2466 0x371c0, 0x371c0, 2467 0x371c8, 0x371d0, 2468 0x371d8, 0x371e0, 2469 0x371ec, 0x37290, 2470 0x37298, 0x372c4, 2471 0x372e4, 0x37390, 2472 0x37398, 0x373c4, 2473 0x373e4, 0x3742c, 2474 0x37434, 0x37450, 2475 0x37458, 0x37458, 2476 0x37460, 0x3748c, 2477 0x3749c, 0x374ac, 2478 0x374c0, 0x374c0, 2479 0x374c8, 0x374d0, 2480 0x374d8, 0x374e0, 2481 0x374ec, 0x3752c, 2482 0x37534, 0x37550, 2483 0x37558, 0x37558, 2484 0x37560, 0x3758c, 2485 0x3759c, 0x375ac, 2486 0x375c0, 0x375c0, 2487 0x375c8, 0x375d0, 2488 0x375d8, 0x375e0, 2489 0x375ec, 0x37690, 2490 0x37698, 0x376c4, 2491 0x376e4, 0x37790, 2492 0x37798, 0x377c4, 2493 0x377e4, 0x377fc, 2494 0x37814, 0x37814, 2495 0x37854, 0x37868, 2496 0x37880, 0x3788c, 2497 0x378c0, 0x378d0, 2498 0x378e8, 0x378ec, 2499 0x37900, 0x3792c, 2500 0x37934, 0x37950, 2501 0x37958, 0x37958, 2502 0x37960, 0x3798c, 2503 0x3799c, 0x379ac, 2504 0x379c0, 0x379c0, 2505 0x379c8, 0x379d0, 2506 0x379d8, 0x379e0, 2507 0x379ec, 0x37a90, 2508 0x37a98, 0x37ac4, 2509 0x37ae4, 0x37b10, 2510 0x37b24, 0x37b28, 2511 0x37b38, 0x37b50, 2512 0x37bf0, 0x37c10, 2513 0x37c24, 0x37c28, 2514 0x37c38, 0x37c50, 2515 0x37cf0, 0x37cfc, 2516 0x40040, 0x40040, 2517 0x40080, 0x40084, 2518 0x40100, 0x40100, 2519 0x40140, 0x401bc, 2520 0x40200, 0x40214, 2521 0x40228, 0x40228, 2522 0x40240, 0x40258, 2523 0x40280, 0x40280, 2524 0x40304, 0x40304, 2525 0x40330, 0x4033c, 2526 0x41304, 0x413c8, 2527 0x413d0, 0x413dc, 2528 0x413f0, 0x413f0, 2529 0x41400, 0x4140c, 2530 0x41414, 0x4141c, 2531 0x41480, 0x414d0, 2532 0x44000, 0x4407c, 2533 0x440c0, 0x441ac, 2534 0x441b4, 0x4427c, 2535 0x442c0, 0x443ac, 2536 0x443b4, 0x4447c, 2537 0x444c0, 0x445ac, 2538 0x445b4, 0x4467c, 2539 0x446c0, 0x447ac, 2540 0x447b4, 0x4487c, 2541 0x448c0, 0x449ac, 2542 0x449b4, 0x44a7c, 2543 0x44ac0, 0x44bac, 2544 0x44bb4, 0x44c7c, 2545 0x44cc0, 0x44dac, 2546 0x44db4, 0x44e7c, 2547 0x44ec0, 0x44fac, 2548 0x44fb4, 0x4507c, 2549 0x450c0, 0x451ac, 2550 0x451b4, 0x451fc, 2551 0x45800, 0x45804, 2552 0x45810, 0x45830, 2553 0x45840, 0x45860, 2554 0x45868, 0x45868, 2555 0x45880, 0x45884, 2556 0x458a0, 0x458b0, 2557 0x45a00, 0x45a04, 2558 0x45a10, 0x45a30, 2559 0x45a40, 0x45a60, 2560 0x45a68, 0x45a68, 2561 0x45a80, 0x45a84, 2562 0x45aa0, 0x45ab0, 2563 0x460c0, 0x460e4, 2564 0x47000, 0x4703c, 2565 0x47044, 0x4708c, 2566 0x47200, 0x47250, 2567 0x47400, 0x47408, 2568 0x47414, 0x47420, 2569 0x47600, 0x47618, 2570 0x47800, 0x47814, 2571 0x47820, 0x4782c, 2572 0x50000, 0x50084, 2573 0x50090, 0x500cc, 2574 0x50300, 0x50384, 2575 0x50400, 0x50400, 2576 0x50800, 0x50884, 2577 0x50890, 0x508cc, 2578 0x50b00, 0x50b84, 2579 0x50c00, 0x50c00, 2580 0x51000, 0x51020, 2581 0x51028, 0x510b0, 2582 0x51300, 0x51324, 2583 }; 2584 2585 static const unsigned int t6vf_reg_ranges[] = { 2586 VF_SGE_REG(A_SGE_VF_KDOORBELL), VF_SGE_REG(A_SGE_VF_GTS), 2587 VF_MPS_REG(A_MPS_VF_CTL), 2588 VF_MPS_REG(A_MPS_VF_STAT_RX_VF_ERR_FRAMES_H), 2589 VF_PL_REG(A_PL_VF_WHOAMI), VF_PL_REG(A_PL_VF_REVISION), 2590 VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_CTRL), 2591 VF_CIM_REG(A_CIM_VF_EXT_MAILBOX_STATUS), 2592 FW_T6VF_MBDATA_BASE_ADDR, 2593 FW_T6VF_MBDATA_BASE_ADDR + 2594 ((NUM_CIM_PF_MAILBOX_DATA_INSTANCES - 1) * 4), 2595 }; 2596 2597 u32 *buf_end = (u32 *)(buf + buf_size); 2598 const unsigned int *reg_ranges; 2599 int reg_ranges_size, range; 2600 unsigned int chip_version = chip_id(adap); 2601 2602 /* 2603 * Select the right set of register ranges to dump depending on the 2604 * adapter chip type. 2605 */ 2606 switch (chip_version) { 2607 case CHELSIO_T4: 2608 if (adap->flags & IS_VF) { 2609 reg_ranges = t4vf_reg_ranges; 2610 reg_ranges_size = ARRAY_SIZE(t4vf_reg_ranges); 2611 } else { 2612 reg_ranges = t4_reg_ranges; 2613 reg_ranges_size = ARRAY_SIZE(t4_reg_ranges); 2614 } 2615 break; 2616 2617 case CHELSIO_T5: 2618 if (adap->flags & IS_VF) { 2619 reg_ranges = t5vf_reg_ranges; 2620 reg_ranges_size = ARRAY_SIZE(t5vf_reg_ranges); 2621 } else { 2622 reg_ranges = t5_reg_ranges; 2623 reg_ranges_size = ARRAY_SIZE(t5_reg_ranges); 2624 } 2625 break; 2626 2627 case CHELSIO_T6: 2628 if (adap->flags & IS_VF) { 2629 reg_ranges = t6vf_reg_ranges; 2630 reg_ranges_size = ARRAY_SIZE(t6vf_reg_ranges); 2631 } else { 2632 reg_ranges = t6_reg_ranges; 2633 reg_ranges_size = ARRAY_SIZE(t6_reg_ranges); 2634 } 2635 break; 2636 2637 default: 2638 CH_ERR(adap, 2639 "Unsupported chip version %d\n", chip_version); 2640 return; 2641 } 2642 2643 /* 2644 * Clear the register buffer and insert the appropriate register 2645 * values selected by the above register ranges. 2646 */ 2647 memset(buf, 0, buf_size); 2648 for (range = 0; range < reg_ranges_size; range += 2) { 2649 unsigned int reg = reg_ranges[range]; 2650 unsigned int last_reg = reg_ranges[range + 1]; 2651 u32 *bufp = (u32 *)(buf + reg); 2652 2653 /* 2654 * Iterate across the register range filling in the register 2655 * buffer but don't write past the end of the register buffer. 2656 */ 2657 while (reg <= last_reg && bufp < buf_end) { 2658 *bufp++ = t4_read_reg(adap, reg); 2659 reg += sizeof(u32); 2660 } 2661 } 2662} 2663 2664/* 2665 * Partial EEPROM Vital Product Data structure. The VPD starts with one ID 2666 * header followed by one or more VPD-R sections, each with its own header. 2667 */ 2668struct t4_vpd_hdr { 2669 u8 id_tag; 2670 u8 id_len[2]; 2671 u8 id_data[ID_LEN]; 2672}; 2673 2674struct t4_vpdr_hdr { 2675 u8 vpdr_tag; 2676 u8 vpdr_len[2]; 2677}; 2678 2679/* 2680 * EEPROM reads take a few tens of us while writes can take a bit over 5 ms. 2681 */ 2682#define EEPROM_DELAY 10 /* 10us per poll spin */ 2683#define EEPROM_MAX_POLL 5000 /* x 5000 == 50ms */ 2684 2685#define EEPROM_STAT_ADDR 0x7bfc 2686#define VPD_SIZE 0x800 2687#define VPD_BASE 0x400 2688#define VPD_BASE_OLD 0 2689#define VPD_LEN 1024 2690#define VPD_INFO_FLD_HDR_SIZE 3 2691#define CHELSIO_VPD_UNIQUE_ID 0x82 2692 2693/* 2694 * Small utility function to wait till any outstanding VPD Access is complete. 2695 * We have a per-adapter state variable "VPD Busy" to indicate when we have a 2696 * VPD Access in flight. This allows us to handle the problem of having a 2697 * previous VPD Access time out and prevent an attempt to inject a new VPD 2698 * Request before any in-flight VPD reguest has completed. 2699 */ 2700static int t4_seeprom_wait(struct adapter *adapter) 2701{ 2702 unsigned int base = adapter->params.pci.vpd_cap_addr; 2703 int max_poll; 2704 2705 /* 2706 * If no VPD Access is in flight, we can just return success right 2707 * away. 2708 */ 2709 if (!adapter->vpd_busy) 2710 return 0; 2711 2712 /* 2713 * Poll the VPD Capability Address/Flag register waiting for it 2714 * to indicate that the operation is complete. 2715 */ 2716 max_poll = EEPROM_MAX_POLL; 2717 do { 2718 u16 val; 2719 2720 udelay(EEPROM_DELAY); 2721 t4_os_pci_read_cfg2(adapter, base + PCI_VPD_ADDR, &val); 2722 2723 /* 2724 * If the operation is complete, mark the VPD as no longer 2725 * busy and return success. 2726 */ 2727 if ((val & PCI_VPD_ADDR_F) == adapter->vpd_flag) { 2728 adapter->vpd_busy = 0; 2729 return 0; 2730 } 2731 } while (--max_poll); 2732 2733 /* 2734 * Failure! Note that we leave the VPD Busy status set in order to 2735 * avoid pushing a new VPD Access request into the VPD Capability till 2736 * the current operation eventually succeeds. It's a bug to issue a 2737 * new request when an existing request is in flight and will result 2738 * in corrupt hardware state. 2739 */ 2740 return -ETIMEDOUT; 2741} 2742 2743/** 2744 * t4_seeprom_read - read a serial EEPROM location 2745 * @adapter: adapter to read 2746 * @addr: EEPROM virtual address 2747 * @data: where to store the read data 2748 * 2749 * Read a 32-bit word from a location in serial EEPROM using the card's PCI 2750 * VPD capability. Note that this function must be called with a virtual 2751 * address. 2752 */ 2753int t4_seeprom_read(struct adapter *adapter, u32 addr, u32 *data) 2754{ 2755 unsigned int base = adapter->params.pci.vpd_cap_addr; 2756 int ret; 2757 2758 /* 2759 * VPD Accesses must alway be 4-byte aligned! 2760 */ 2761 if (addr >= EEPROMVSIZE || (addr & 3)) 2762 return -EINVAL; 2763 2764 /* 2765 * Wait for any previous operation which may still be in flight to 2766 * complete. 2767 */ 2768 ret = t4_seeprom_wait(adapter); 2769 if (ret) { 2770 CH_ERR(adapter, "VPD still busy from previous operation\n"); 2771 return ret; 2772 } 2773 2774 /* 2775 * Issue our new VPD Read request, mark the VPD as being busy and wait 2776 * for our request to complete. If it doesn't complete, note the 2777 * error and return it to our caller. Note that we do not reset the 2778 * VPD Busy status! 2779 */ 2780 t4_os_pci_write_cfg2(adapter, base + PCI_VPD_ADDR, (u16)addr); 2781 adapter->vpd_busy = 1; 2782 adapter->vpd_flag = PCI_VPD_ADDR_F; 2783 ret = t4_seeprom_wait(adapter); 2784 if (ret) { 2785 CH_ERR(adapter, "VPD read of address %#x failed\n", addr); 2786 return ret; 2787 } 2788 2789 /* 2790 * Grab the returned data, swizzle it into our endianness and 2791 * return success. 2792 */ 2793 t4_os_pci_read_cfg4(adapter, base + PCI_VPD_DATA, data); 2794 *data = le32_to_cpu(*data); 2795 return 0; 2796} 2797 2798/** 2799 * t4_seeprom_write - write a serial EEPROM location 2800 * @adapter: adapter to write 2801 * @addr: virtual EEPROM address 2802 * @data: value to write 2803 * 2804 * Write a 32-bit word to a location in serial EEPROM using the card's PCI 2805 * VPD capability. Note that this function must be called with a virtual 2806 * address. 2807 */ 2808int t4_seeprom_write(struct adapter *adapter, u32 addr, u32 data) 2809{ 2810 unsigned int base = adapter->params.pci.vpd_cap_addr; 2811 int ret; 2812 u32 stats_reg; 2813 int max_poll; 2814 2815 /* 2816 * VPD Accesses must alway be 4-byte aligned! 2817 */ 2818 if (addr >= EEPROMVSIZE || (addr & 3)) 2819 return -EINVAL; 2820 2821 /* 2822 * Wait for any previous operation which may still be in flight to 2823 * complete. 2824 */ 2825 ret = t4_seeprom_wait(adapter); 2826 if (ret) { 2827 CH_ERR(adapter, "VPD still busy from previous operation\n"); 2828 return ret; 2829 } 2830 2831 /* 2832 * Issue our new VPD Read request, mark the VPD as being busy and wait 2833 * for our request to complete. If it doesn't complete, note the 2834 * error and return it to our caller. Note that we do not reset the 2835 * VPD Busy status! 2836 */ 2837 t4_os_pci_write_cfg4(adapter, base + PCI_VPD_DATA, 2838 cpu_to_le32(data)); 2839 t4_os_pci_write_cfg2(adapter, base + PCI_VPD_ADDR, 2840 (u16)addr | PCI_VPD_ADDR_F); 2841 adapter->vpd_busy = 1; 2842 adapter->vpd_flag = 0; 2843 ret = t4_seeprom_wait(adapter); 2844 if (ret) { 2845 CH_ERR(adapter, "VPD write of address %#x failed\n", addr); 2846 return ret; 2847 } 2848 2849 /* 2850 * Reset PCI_VPD_DATA register after a transaction and wait for our 2851 * request to complete. If it doesn't complete, return error. 2852 */ 2853 t4_os_pci_write_cfg4(adapter, base + PCI_VPD_DATA, 0); 2854 max_poll = EEPROM_MAX_POLL; 2855 do { 2856 udelay(EEPROM_DELAY); 2857 t4_seeprom_read(adapter, EEPROM_STAT_ADDR, &stats_reg); 2858 } while ((stats_reg & 0x1) && --max_poll); 2859 if (!max_poll) 2860 return -ETIMEDOUT; 2861 2862 /* Return success! */ 2863 return 0; 2864} 2865 2866/** 2867 * t4_eeprom_ptov - translate a physical EEPROM address to virtual 2868 * @phys_addr: the physical EEPROM address 2869 * @fn: the PCI function number 2870 * @sz: size of function-specific area 2871 * 2872 * Translate a physical EEPROM address to virtual. The first 1K is 2873 * accessed through virtual addresses starting at 31K, the rest is 2874 * accessed through virtual addresses starting at 0. 2875 * 2876 * The mapping is as follows: 2877 * [0..1K) -> [31K..32K) 2878 * [1K..1K+A) -> [ES-A..ES) 2879 * [1K+A..ES) -> [0..ES-A-1K) 2880 * 2881 * where A = @fn * @sz, and ES = EEPROM size. 2882 */ 2883int t4_eeprom_ptov(unsigned int phys_addr, unsigned int fn, unsigned int sz) 2884{ 2885 fn *= sz; 2886 if (phys_addr < 1024) 2887 return phys_addr + (31 << 10); 2888 if (phys_addr < 1024 + fn) 2889 return EEPROMSIZE - fn + phys_addr - 1024; 2890 if (phys_addr < EEPROMSIZE) 2891 return phys_addr - 1024 - fn; 2892 return -EINVAL; 2893} 2894 2895/** 2896 * t4_seeprom_wp - enable/disable EEPROM write protection 2897 * @adapter: the adapter 2898 * @enable: whether to enable or disable write protection 2899 * 2900 * Enables or disables write protection on the serial EEPROM. 2901 */ 2902int t4_seeprom_wp(struct adapter *adapter, int enable) 2903{ 2904 return t4_seeprom_write(adapter, EEPROM_STAT_ADDR, enable ? 0xc : 0); 2905} 2906 2907/** 2908 * get_vpd_keyword_val - Locates an information field keyword in the VPD 2909 * @vpd: Pointer to buffered vpd data structure 2910 * @kw: The keyword to search for 2911 * @region: VPD region to search (starting from 0) 2912 * 2913 * Returns the value of the information field keyword or 2914 * -ENOENT otherwise. 2915 */ 2916static int get_vpd_keyword_val(const u8 *vpd, const char *kw, int region) 2917{ 2918 int i, tag; 2919 unsigned int offset, len; 2920 const struct t4_vpdr_hdr *vpdr; 2921 2922 offset = sizeof(struct t4_vpd_hdr); 2923 vpdr = (const void *)(vpd + offset); 2924 tag = vpdr->vpdr_tag; 2925 len = (u16)vpdr->vpdr_len[0] + ((u16)vpdr->vpdr_len[1] << 8); 2926 while (region--) { 2927 offset += sizeof(struct t4_vpdr_hdr) + len; 2928 vpdr = (const void *)(vpd + offset); 2929 if (++tag != vpdr->vpdr_tag) 2930 return -ENOENT; 2931 len = (u16)vpdr->vpdr_len[0] + ((u16)vpdr->vpdr_len[1] << 8); 2932 } 2933 offset += sizeof(struct t4_vpdr_hdr); 2934 2935 if (offset + len > VPD_LEN) { 2936 return -ENOENT; 2937 } 2938 2939 for (i = offset; i + VPD_INFO_FLD_HDR_SIZE <= offset + len;) { 2940 if (memcmp(vpd + i , kw , 2) == 0){ 2941 i += VPD_INFO_FLD_HDR_SIZE; 2942 return i; 2943 } 2944 2945 i += VPD_INFO_FLD_HDR_SIZE + vpd[i+2]; 2946 } 2947 2948 return -ENOENT; 2949} 2950 2951 2952/** 2953 * get_vpd_params - read VPD parameters from VPD EEPROM 2954 * @adapter: adapter to read 2955 * @p: where to store the parameters 2956 * @vpd: caller provided temporary space to read the VPD into 2957 * 2958 * Reads card parameters stored in VPD EEPROM. 2959 */ 2960static int get_vpd_params(struct adapter *adapter, struct vpd_params *p, 2961 u32 *buf) 2962{ 2963 int i, ret, addr; 2964 int ec, sn, pn, na, md; 2965 u8 csum; 2966 const u8 *vpd = (const u8 *)buf; 2967 2968 /* 2969 * Card information normally starts at VPD_BASE but early cards had 2970 * it at 0. 2971 */ 2972 ret = t4_seeprom_read(adapter, VPD_BASE, buf); 2973 if (ret) 2974 return (ret); 2975 2976 /* 2977 * The VPD shall have a unique identifier specified by the PCI SIG. 2978 * For chelsio adapters, the identifier is 0x82. The first byte of a VPD 2979 * shall be CHELSIO_VPD_UNIQUE_ID (0x82). The VPD programming software 2980 * is expected to automatically put this entry at the 2981 * beginning of the VPD. 2982 */ 2983 addr = *vpd == CHELSIO_VPD_UNIQUE_ID ? VPD_BASE : VPD_BASE_OLD; 2984 2985 for (i = 0; i < VPD_LEN; i += 4) { 2986 ret = t4_seeprom_read(adapter, addr + i, buf++); 2987 if (ret) 2988 return ret; 2989 } 2990 2991#define FIND_VPD_KW(var,name) do { \ 2992 var = get_vpd_keyword_val(vpd, name, 0); \ 2993 if (var < 0) { \ 2994 CH_ERR(adapter, "missing VPD keyword " name "\n"); \ 2995 return -EINVAL; \ 2996 } \ 2997} while (0) 2998 2999 FIND_VPD_KW(i, "RV"); 3000 for (csum = 0; i >= 0; i--) 3001 csum += vpd[i]; 3002 3003 if (csum) { 3004 CH_ERR(adapter, 3005 "corrupted VPD EEPROM, actual csum %u\n", csum); 3006 return -EINVAL; 3007 } 3008 3009 FIND_VPD_KW(ec, "EC"); 3010 FIND_VPD_KW(sn, "SN"); 3011 FIND_VPD_KW(pn, "PN"); 3012 FIND_VPD_KW(na, "NA"); 3013#undef FIND_VPD_KW 3014 3015 memcpy(p->id, vpd + offsetof(struct t4_vpd_hdr, id_data), ID_LEN); 3016 strstrip(p->id); 3017 memcpy(p->ec, vpd + ec, EC_LEN); 3018 strstrip(p->ec); 3019 i = vpd[sn - VPD_INFO_FLD_HDR_SIZE + 2]; 3020 memcpy(p->sn, vpd + sn, min(i, SERNUM_LEN)); 3021 strstrip(p->sn); 3022 i = vpd[pn - VPD_INFO_FLD_HDR_SIZE + 2]; 3023 memcpy(p->pn, vpd + pn, min(i, PN_LEN)); 3024 strstrip((char *)p->pn); 3025 i = vpd[na - VPD_INFO_FLD_HDR_SIZE + 2]; 3026 memcpy(p->na, vpd + na, min(i, MACADDR_LEN)); 3027 strstrip((char *)p->na); 3028 3029 md = get_vpd_keyword_val(vpd, "VF", 1); 3030 if (md < 0) { 3031 snprintf(p->md, sizeof(p->md), "unknown"); 3032 } else { 3033 i = vpd[md - VPD_INFO_FLD_HDR_SIZE + 2]; 3034 memcpy(p->md, vpd + md, min(i, MD_LEN)); 3035 } 3036 3037 return 0; 3038} 3039 3040/* serial flash and firmware constants and flash config file constants */ 3041enum { 3042 SF_ATTEMPTS = 10, /* max retries for SF operations */ 3043 3044 /* flash command opcodes */ 3045 SF_PROG_PAGE = 2, /* program 256B page */ 3046 SF_WR_DISABLE = 4, /* disable writes */ 3047 SF_RD_STATUS = 5, /* read status register */ 3048 SF_WR_ENABLE = 6, /* enable writes */ 3049 SF_RD_DATA_FAST = 0xb, /* read flash */ 3050 SF_RD_ID = 0x9f, /* read ID */ 3051 SF_ERASE_SECTOR = 0xd8, /* erase 64KB sector */ 3052}; 3053 3054/** 3055 * sf1_read - read data from the serial flash 3056 * @adapter: the adapter 3057 * @byte_cnt: number of bytes to read 3058 * @cont: whether another operation will be chained 3059 * @lock: whether to lock SF for PL access only 3060 * @valp: where to store the read data 3061 * 3062 * Reads up to 4 bytes of data from the serial flash. The location of 3063 * the read needs to be specified prior to calling this by issuing the 3064 * appropriate commands to the serial flash. 3065 */ 3066static int sf1_read(struct adapter *adapter, unsigned int byte_cnt, int cont, 3067 int lock, u32 *valp) 3068{ 3069 int ret; 3070 3071 if (!byte_cnt || byte_cnt > 4) 3072 return -EINVAL; 3073 if (t4_read_reg(adapter, A_SF_OP) & F_BUSY) 3074 return -EBUSY; 3075 t4_write_reg(adapter, A_SF_OP, 3076 V_SF_LOCK(lock) | V_CONT(cont) | V_BYTECNT(byte_cnt - 1)); 3077 ret = t4_wait_op_done(adapter, A_SF_OP, F_BUSY, 0, SF_ATTEMPTS, 5); 3078 if (!ret) 3079 *valp = t4_read_reg(adapter, A_SF_DATA); 3080 return ret; 3081} 3082 3083/** 3084 * sf1_write - write data to the serial flash 3085 * @adapter: the adapter 3086 * @byte_cnt: number of bytes to write 3087 * @cont: whether another operation will be chained 3088 * @lock: whether to lock SF for PL access only 3089 * @val: value to write 3090 * 3091 * Writes up to 4 bytes of data to the serial flash. The location of 3092 * the write needs to be specified prior to calling this by issuing the 3093 * appropriate commands to the serial flash. 3094 */ 3095static int sf1_write(struct adapter *adapter, unsigned int byte_cnt, int cont, 3096 int lock, u32 val) 3097{ 3098 if (!byte_cnt || byte_cnt > 4) 3099 return -EINVAL; 3100 if (t4_read_reg(adapter, A_SF_OP) & F_BUSY) 3101 return -EBUSY; 3102 t4_write_reg(adapter, A_SF_DATA, val); 3103 t4_write_reg(adapter, A_SF_OP, V_SF_LOCK(lock) | 3104 V_CONT(cont) | V_BYTECNT(byte_cnt - 1) | V_OP(1)); 3105 return t4_wait_op_done(adapter, A_SF_OP, F_BUSY, 0, SF_ATTEMPTS, 5); 3106} 3107 3108/** 3109 * flash_wait_op - wait for a flash operation to complete 3110 * @adapter: the adapter 3111 * @attempts: max number of polls of the status register 3112 * @delay: delay between polls in ms 3113 * 3114 * Wait for a flash operation to complete by polling the status register. 3115 */ 3116static int flash_wait_op(struct adapter *adapter, int attempts, int delay) 3117{ 3118 int ret; 3119 u32 status; 3120 3121 while (1) { 3122 if ((ret = sf1_write(adapter, 1, 1, 1, SF_RD_STATUS)) != 0 || 3123 (ret = sf1_read(adapter, 1, 0, 1, &status)) != 0) 3124 return ret; 3125 if (!(status & 1)) 3126 return 0; 3127 if (--attempts == 0) 3128 return -EAGAIN; 3129 if (delay) 3130 msleep(delay); 3131 } 3132} 3133 3134/** 3135 * t4_read_flash - read words from serial flash 3136 * @adapter: the adapter 3137 * @addr: the start address for the read 3138 * @nwords: how many 32-bit words to read 3139 * @data: where to store the read data 3140 * @byte_oriented: whether to store data as bytes or as words 3141 * 3142 * Read the specified number of 32-bit words from the serial flash. 3143 * If @byte_oriented is set the read data is stored as a byte array 3144 * (i.e., big-endian), otherwise as 32-bit words in the platform's 3145 * natural endianness. 3146 */ 3147int t4_read_flash(struct adapter *adapter, unsigned int addr, 3148 unsigned int nwords, u32 *data, int byte_oriented) 3149{ 3150 int ret; 3151 3152 if (addr + nwords * sizeof(u32) > adapter->params.sf_size || (addr & 3)) 3153 return -EINVAL; 3154 3155 addr = swab32(addr) | SF_RD_DATA_FAST; 3156 3157 if ((ret = sf1_write(adapter, 4, 1, 0, addr)) != 0 || 3158 (ret = sf1_read(adapter, 1, 1, 0, data)) != 0) 3159 return ret; 3160 3161 for ( ; nwords; nwords--, data++) { 3162 ret = sf1_read(adapter, 4, nwords > 1, nwords == 1, data); 3163 if (nwords == 1) 3164 t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ 3165 if (ret) 3166 return ret; 3167 if (byte_oriented) 3168 *data = (__force __u32)(cpu_to_be32(*data)); 3169 } 3170 return 0; 3171} 3172 3173/** 3174 * t4_write_flash - write up to a page of data to the serial flash 3175 * @adapter: the adapter 3176 * @addr: the start address to write 3177 * @n: length of data to write in bytes 3178 * @data: the data to write 3179 * @byte_oriented: whether to store data as bytes or as words 3180 * 3181 * Writes up to a page of data (256 bytes) to the serial flash starting 3182 * at the given address. All the data must be written to the same page. 3183 * If @byte_oriented is set the write data is stored as byte stream 3184 * (i.e. matches what on disk), otherwise in big-endian. 3185 */ 3186int t4_write_flash(struct adapter *adapter, unsigned int addr, 3187 unsigned int n, const u8 *data, int byte_oriented) 3188{ 3189 int ret; 3190 u32 buf[SF_PAGE_SIZE / 4]; 3191 unsigned int i, c, left, val, offset = addr & 0xff; 3192 3193 if (addr >= adapter->params.sf_size || offset + n > SF_PAGE_SIZE) 3194 return -EINVAL; 3195 3196 val = swab32(addr) | SF_PROG_PAGE; 3197 3198 if ((ret = sf1_write(adapter, 1, 0, 1, SF_WR_ENABLE)) != 0 || 3199 (ret = sf1_write(adapter, 4, 1, 1, val)) != 0) 3200 goto unlock; 3201 3202 for (left = n; left; left -= c) { 3203 c = min(left, 4U); 3204 for (val = 0, i = 0; i < c; ++i) 3205 val = (val << 8) + *data++; 3206 3207 if (!byte_oriented) 3208 val = cpu_to_be32(val); 3209 3210 ret = sf1_write(adapter, c, c != left, 1, val); 3211 if (ret) 3212 goto unlock; 3213 } 3214 ret = flash_wait_op(adapter, 8, 1); 3215 if (ret) 3216 goto unlock; 3217 3218 t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ 3219 3220 /* Read the page to verify the write succeeded */ 3221 ret = t4_read_flash(adapter, addr & ~0xff, ARRAY_SIZE(buf), buf, 3222 byte_oriented); 3223 if (ret) 3224 return ret; 3225 3226 if (memcmp(data - n, (u8 *)buf + offset, n)) { 3227 CH_ERR(adapter, 3228 "failed to correctly write the flash page at %#x\n", 3229 addr); 3230 return -EIO; 3231 } 3232 return 0; 3233 3234unlock: 3235 t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ 3236 return ret; 3237} 3238 3239/** 3240 * t4_get_fw_version - read the firmware version 3241 * @adapter: the adapter 3242 * @vers: where to place the version 3243 * 3244 * Reads the FW version from flash. 3245 */ 3246int t4_get_fw_version(struct adapter *adapter, u32 *vers) 3247{ 3248 return t4_read_flash(adapter, FLASH_FW_START + 3249 offsetof(struct fw_hdr, fw_ver), 1, 3250 vers, 0); 3251} 3252 3253/** 3254 * t4_get_bs_version - read the firmware bootstrap version 3255 * @adapter: the adapter 3256 * @vers: where to place the version 3257 * 3258 * Reads the FW Bootstrap version from flash. 3259 */ 3260int t4_get_bs_version(struct adapter *adapter, u32 *vers) 3261{ 3262 return t4_read_flash(adapter, FLASH_FWBOOTSTRAP_START + 3263 offsetof(struct fw_hdr, fw_ver), 1, 3264 vers, 0); 3265} 3266 3267/** 3268 * t4_get_tp_version - read the TP microcode version 3269 * @adapter: the adapter 3270 * @vers: where to place the version 3271 * 3272 * Reads the TP microcode version from flash. 3273 */ 3274int t4_get_tp_version(struct adapter *adapter, u32 *vers) 3275{ 3276 return t4_read_flash(adapter, FLASH_FW_START + 3277 offsetof(struct fw_hdr, tp_microcode_ver), 3278 1, vers, 0); 3279} 3280 3281/** 3282 * t4_get_exprom_version - return the Expansion ROM version (if any) 3283 * @adapter: the adapter 3284 * @vers: where to place the version 3285 * 3286 * Reads the Expansion ROM header from FLASH and returns the version 3287 * number (if present) through the @vers return value pointer. We return 3288 * this in the Firmware Version Format since it's convenient. Return 3289 * 0 on success, -ENOENT if no Expansion ROM is present. 3290 */ 3291int t4_get_exprom_version(struct adapter *adap, u32 *vers) 3292{ 3293 struct exprom_header { 3294 unsigned char hdr_arr[16]; /* must start with 0x55aa */ 3295 unsigned char hdr_ver[4]; /* Expansion ROM version */ 3296 } *hdr; 3297 u32 exprom_header_buf[DIV_ROUND_UP(sizeof(struct exprom_header), 3298 sizeof(u32))]; 3299 int ret; 3300 3301 ret = t4_read_flash(adap, FLASH_EXP_ROM_START, 3302 ARRAY_SIZE(exprom_header_buf), exprom_header_buf, 3303 0); 3304 if (ret) 3305 return ret; 3306 3307 hdr = (struct exprom_header *)exprom_header_buf; 3308 if (hdr->hdr_arr[0] != 0x55 || hdr->hdr_arr[1] != 0xaa) 3309 return -ENOENT; 3310 3311 *vers = (V_FW_HDR_FW_VER_MAJOR(hdr->hdr_ver[0]) | 3312 V_FW_HDR_FW_VER_MINOR(hdr->hdr_ver[1]) | 3313 V_FW_HDR_FW_VER_MICRO(hdr->hdr_ver[2]) | 3314 V_FW_HDR_FW_VER_BUILD(hdr->hdr_ver[3])); 3315 return 0; 3316} 3317 3318/** 3319 * t4_get_scfg_version - return the Serial Configuration version 3320 * @adapter: the adapter 3321 * @vers: where to place the version 3322 * 3323 * Reads the Serial Configuration Version via the Firmware interface 3324 * (thus this can only be called once we're ready to issue Firmware 3325 * commands). The format of the Serial Configuration version is 3326 * adapter specific. Returns 0 on success, an error on failure. 3327 * 3328 * Note that early versions of the Firmware didn't include the ability 3329 * to retrieve the Serial Configuration version, so we zero-out the 3330 * return-value parameter in that case to avoid leaving it with 3331 * garbage in it. 3332 * 3333 * Also note that the Firmware will return its cached copy of the Serial 3334 * Initialization Revision ID, not the actual Revision ID as written in 3335 * the Serial EEPROM. This is only an issue if a new VPD has been written 3336 * and the Firmware/Chip haven't yet gone through a RESET sequence. So 3337 * it's best to defer calling this routine till after a FW_RESET_CMD has 3338 * been issued if the Host Driver will be performing a full adapter 3339 * initialization. 3340 */ 3341int t4_get_scfg_version(struct adapter *adapter, u32 *vers) 3342{ 3343 u32 scfgrev_param; 3344 int ret; 3345 3346 scfgrev_param = (V_FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) | 3347 V_FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_SCFGREV)); 3348 ret = t4_query_params(adapter, adapter->mbox, adapter->pf, 0, 3349 1, &scfgrev_param, vers); 3350 if (ret) 3351 *vers = 0; 3352 return ret; 3353} 3354 3355/** 3356 * t4_get_vpd_version - return the VPD version 3357 * @adapter: the adapter 3358 * @vers: where to place the version 3359 * 3360 * Reads the VPD via the Firmware interface (thus this can only be called 3361 * once we're ready to issue Firmware commands). The format of the 3362 * VPD version is adapter specific. Returns 0 on success, an error on 3363 * failure. 3364 * 3365 * Note that early versions of the Firmware didn't include the ability 3366 * to retrieve the VPD version, so we zero-out the return-value parameter 3367 * in that case to avoid leaving it with garbage in it. 3368 * 3369 * Also note that the Firmware will return its cached copy of the VPD 3370 * Revision ID, not the actual Revision ID as written in the Serial 3371 * EEPROM. This is only an issue if a new VPD has been written and the 3372 * Firmware/Chip haven't yet gone through a RESET sequence. So it's best 3373 * to defer calling this routine till after a FW_RESET_CMD has been issued 3374 * if the Host Driver will be performing a full adapter initialization. 3375 */ 3376int t4_get_vpd_version(struct adapter *adapter, u32 *vers) 3377{ 3378 u32 vpdrev_param; 3379 int ret; 3380 3381 vpdrev_param = (V_FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) | 3382 V_FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_VPDREV)); 3383 ret = t4_query_params(adapter, adapter->mbox, adapter->pf, 0, 3384 1, &vpdrev_param, vers); 3385 if (ret) 3386 *vers = 0; 3387 return ret; 3388} 3389 3390/** 3391 * t4_get_version_info - extract various chip/firmware version information 3392 * @adapter: the adapter 3393 * 3394 * Reads various chip/firmware version numbers and stores them into the 3395 * adapter Adapter Parameters structure. If any of the efforts fails 3396 * the first failure will be returned, but all of the version numbers 3397 * will be read. 3398 */ 3399int t4_get_version_info(struct adapter *adapter) 3400{ 3401 int ret = 0; 3402 3403 #define FIRST_RET(__getvinfo) \ 3404 do { \ 3405 int __ret = __getvinfo; \ 3406 if (__ret && !ret) \ 3407 ret = __ret; \ 3408 } while (0) 3409 3410 FIRST_RET(t4_get_fw_version(adapter, &adapter->params.fw_vers)); 3411 FIRST_RET(t4_get_bs_version(adapter, &adapter->params.bs_vers)); 3412 FIRST_RET(t4_get_tp_version(adapter, &adapter->params.tp_vers)); 3413 FIRST_RET(t4_get_exprom_version(adapter, &adapter->params.er_vers)); 3414 FIRST_RET(t4_get_scfg_version(adapter, &adapter->params.scfg_vers)); 3415 FIRST_RET(t4_get_vpd_version(adapter, &adapter->params.vpd_vers)); 3416 3417 #undef FIRST_RET 3418 3419 return ret; 3420} 3421 3422/** 3423 * t4_flash_erase_sectors - erase a range of flash sectors 3424 * @adapter: the adapter 3425 * @start: the first sector to erase 3426 * @end: the last sector to erase 3427 * 3428 * Erases the sectors in the given inclusive range. 3429 */ 3430int t4_flash_erase_sectors(struct adapter *adapter, int start, int end) 3431{ 3432 int ret = 0; 3433 3434 if (end >= adapter->params.sf_nsec) 3435 return -EINVAL; 3436 3437 while (start <= end) { 3438 if ((ret = sf1_write(adapter, 1, 0, 1, SF_WR_ENABLE)) != 0 || 3439 (ret = sf1_write(adapter, 4, 0, 1, 3440 SF_ERASE_SECTOR | (start << 8))) != 0 || 3441 (ret = flash_wait_op(adapter, 14, 500)) != 0) { 3442 CH_ERR(adapter, 3443 "erase of flash sector %d failed, error %d\n", 3444 start, ret); 3445 break; 3446 } 3447 start++; 3448 } 3449 t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ 3450 return ret; 3451} 3452 3453/** 3454 * t4_flash_cfg_addr - return the address of the flash configuration file 3455 * @adapter: the adapter 3456 * 3457 * Return the address within the flash where the Firmware Configuration 3458 * File is stored, or an error if the device FLASH is too small to contain 3459 * a Firmware Configuration File. 3460 */ 3461int t4_flash_cfg_addr(struct adapter *adapter) 3462{ 3463 /* 3464 * If the device FLASH isn't large enough to hold a Firmware 3465 * Configuration File, return an error. 3466 */ 3467 if (adapter->params.sf_size < FLASH_CFG_START + FLASH_CFG_MAX_SIZE) 3468 return -ENOSPC; 3469 3470 return FLASH_CFG_START; 3471} 3472 3473/* 3474 * Return TRUE if the specified firmware matches the adapter. I.e. T4 3475 * firmware for T4 adapters, T5 firmware for T5 adapters, etc. We go ahead 3476 * and emit an error message for mismatched firmware to save our caller the 3477 * effort ... 3478 */ 3479static int t4_fw_matches_chip(struct adapter *adap, 3480 const struct fw_hdr *hdr) 3481{ 3482 /* 3483 * The expression below will return FALSE for any unsupported adapter 3484 * which will keep us "honest" in the future ... 3485 */ 3486 if ((is_t4(adap) && hdr->chip == FW_HDR_CHIP_T4) || 3487 (is_t5(adap) && hdr->chip == FW_HDR_CHIP_T5) || 3488 (is_t6(adap) && hdr->chip == FW_HDR_CHIP_T6)) 3489 return 1; 3490 3491 CH_ERR(adap, 3492 "FW image (%d) is not suitable for this adapter (%d)\n", 3493 hdr->chip, chip_id(adap)); 3494 return 0; 3495} 3496 3497/** 3498 * t4_load_fw - download firmware 3499 * @adap: the adapter 3500 * @fw_data: the firmware image to write 3501 * @size: image size 3502 * 3503 * Write the supplied firmware image to the card's serial flash. 3504 */ 3505int t4_load_fw(struct adapter *adap, const u8 *fw_data, unsigned int size) 3506{ 3507 u32 csum; 3508 int ret, addr; 3509 unsigned int i; 3510 u8 first_page[SF_PAGE_SIZE]; 3511 const u32 *p = (const u32 *)fw_data; 3512 const struct fw_hdr *hdr = (const struct fw_hdr *)fw_data; 3513 unsigned int sf_sec_size = adap->params.sf_size / adap->params.sf_nsec; 3514 unsigned int fw_start_sec; 3515 unsigned int fw_start; 3516 unsigned int fw_size; 3517 3518 if (ntohl(hdr->magic) == FW_HDR_MAGIC_BOOTSTRAP) { 3519 fw_start_sec = FLASH_FWBOOTSTRAP_START_SEC; 3520 fw_start = FLASH_FWBOOTSTRAP_START; 3521 fw_size = FLASH_FWBOOTSTRAP_MAX_SIZE; 3522 } else { 3523 fw_start_sec = FLASH_FW_START_SEC; 3524 fw_start = FLASH_FW_START; 3525 fw_size = FLASH_FW_MAX_SIZE; 3526 } 3527 3528 if (!size) { 3529 CH_ERR(adap, "FW image has no data\n"); 3530 return -EINVAL; 3531 } 3532 if (size & 511) { 3533 CH_ERR(adap, 3534 "FW image size not multiple of 512 bytes\n"); 3535 return -EINVAL; 3536 } 3537 if ((unsigned int) be16_to_cpu(hdr->len512) * 512 != size) { 3538 CH_ERR(adap, 3539 "FW image size differs from size in FW header\n"); 3540 return -EINVAL; 3541 } 3542 if (size > fw_size) { 3543 CH_ERR(adap, "FW image too large, max is %u bytes\n", 3544 fw_size); 3545 return -EFBIG; 3546 } 3547 if (!t4_fw_matches_chip(adap, hdr)) 3548 return -EINVAL; 3549 3550 for (csum = 0, i = 0; i < size / sizeof(csum); i++) 3551 csum += be32_to_cpu(p[i]); 3552 3553 if (csum != 0xffffffff) { 3554 CH_ERR(adap, 3555 "corrupted firmware image, checksum %#x\n", csum); 3556 return -EINVAL; 3557 } 3558 3559 i = DIV_ROUND_UP(size, sf_sec_size); /* # of sectors spanned */ 3560 ret = t4_flash_erase_sectors(adap, fw_start_sec, fw_start_sec + i - 1); 3561 if (ret) 3562 goto out; 3563 3564 /* 3565 * We write the correct version at the end so the driver can see a bad 3566 * version if the FW write fails. Start by writing a copy of the 3567 * first page with a bad version. 3568 */ 3569 memcpy(first_page, fw_data, SF_PAGE_SIZE); 3570 ((struct fw_hdr *)first_page)->fw_ver = cpu_to_be32(0xffffffff); 3571 ret = t4_write_flash(adap, fw_start, SF_PAGE_SIZE, first_page, 1); 3572 if (ret) 3573 goto out; 3574 3575 addr = fw_start; 3576 for (size -= SF_PAGE_SIZE; size; size -= SF_PAGE_SIZE) { 3577 addr += SF_PAGE_SIZE; 3578 fw_data += SF_PAGE_SIZE; 3579 ret = t4_write_flash(adap, addr, SF_PAGE_SIZE, fw_data, 1); 3580 if (ret) 3581 goto out; 3582 } 3583 3584 ret = t4_write_flash(adap, 3585 fw_start + offsetof(struct fw_hdr, fw_ver), 3586 sizeof(hdr->fw_ver), (const u8 *)&hdr->fw_ver, 1); 3587out: 3588 if (ret) 3589 CH_ERR(adap, "firmware download failed, error %d\n", 3590 ret); 3591 return ret; 3592} 3593 3594/** 3595 * t4_fwcache - firmware cache operation 3596 * @adap: the adapter 3597 * @op : the operation (flush or flush and invalidate) 3598 */ 3599int t4_fwcache(struct adapter *adap, enum fw_params_param_dev_fwcache op) 3600{ 3601 struct fw_params_cmd c; 3602 3603 memset(&c, 0, sizeof(c)); 3604 c.op_to_vfn = 3605 cpu_to_be32(V_FW_CMD_OP(FW_PARAMS_CMD) | 3606 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 3607 V_FW_PARAMS_CMD_PFN(adap->pf) | 3608 V_FW_PARAMS_CMD_VFN(0)); 3609 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 3610 c.param[0].mnem = 3611 cpu_to_be32(V_FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) | 3612 V_FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_FWCACHE)); 3613 c.param[0].val = (__force __be32)op; 3614 3615 return t4_wr_mbox(adap, adap->mbox, &c, sizeof(c), NULL); 3616} 3617 3618void t4_cim_read_pif_la(struct adapter *adap, u32 *pif_req, u32 *pif_rsp, 3619 unsigned int *pif_req_wrptr, 3620 unsigned int *pif_rsp_wrptr) 3621{ 3622 int i, j; 3623 u32 cfg, val, req, rsp; 3624 3625 cfg = t4_read_reg(adap, A_CIM_DEBUGCFG); 3626 if (cfg & F_LADBGEN) 3627 t4_write_reg(adap, A_CIM_DEBUGCFG, cfg ^ F_LADBGEN); 3628 3629 val = t4_read_reg(adap, A_CIM_DEBUGSTS); 3630 req = G_POLADBGWRPTR(val); 3631 rsp = G_PILADBGWRPTR(val); 3632 if (pif_req_wrptr) 3633 *pif_req_wrptr = req; 3634 if (pif_rsp_wrptr) 3635 *pif_rsp_wrptr = rsp; 3636 3637 for (i = 0; i < CIM_PIFLA_SIZE; i++) { 3638 for (j = 0; j < 6; j++) { 3639 t4_write_reg(adap, A_CIM_DEBUGCFG, V_POLADBGRDPTR(req) | 3640 V_PILADBGRDPTR(rsp)); 3641 *pif_req++ = t4_read_reg(adap, A_CIM_PO_LA_DEBUGDATA); 3642 *pif_rsp++ = t4_read_reg(adap, A_CIM_PI_LA_DEBUGDATA); 3643 req++; 3644 rsp++; 3645 } 3646 req = (req + 2) & M_POLADBGRDPTR; 3647 rsp = (rsp + 2) & M_PILADBGRDPTR; 3648 } 3649 t4_write_reg(adap, A_CIM_DEBUGCFG, cfg); 3650} 3651 3652void t4_cim_read_ma_la(struct adapter *adap, u32 *ma_req, u32 *ma_rsp) 3653{ 3654 u32 cfg; 3655 int i, j, idx; 3656 3657 cfg = t4_read_reg(adap, A_CIM_DEBUGCFG); 3658 if (cfg & F_LADBGEN) 3659 t4_write_reg(adap, A_CIM_DEBUGCFG, cfg ^ F_LADBGEN); 3660 3661 for (i = 0; i < CIM_MALA_SIZE; i++) { 3662 for (j = 0; j < 5; j++) { 3663 idx = 8 * i + j; 3664 t4_write_reg(adap, A_CIM_DEBUGCFG, V_POLADBGRDPTR(idx) | 3665 V_PILADBGRDPTR(idx)); 3666 *ma_req++ = t4_read_reg(adap, A_CIM_PO_LA_MADEBUGDATA); 3667 *ma_rsp++ = t4_read_reg(adap, A_CIM_PI_LA_MADEBUGDATA); 3668 } 3669 } 3670 t4_write_reg(adap, A_CIM_DEBUGCFG, cfg); 3671} 3672 3673void t4_ulprx_read_la(struct adapter *adap, u32 *la_buf) 3674{ 3675 unsigned int i, j; 3676 3677 for (i = 0; i < 8; i++) { 3678 u32 *p = la_buf + i; 3679 3680 t4_write_reg(adap, A_ULP_RX_LA_CTL, i); 3681 j = t4_read_reg(adap, A_ULP_RX_LA_WRPTR); 3682 t4_write_reg(adap, A_ULP_RX_LA_RDPTR, j); 3683 for (j = 0; j < ULPRX_LA_SIZE; j++, p += 8) 3684 *p = t4_read_reg(adap, A_ULP_RX_LA_RDDATA); 3685 } 3686} 3687 3688/** 3689 * t4_link_l1cfg - apply link configuration to MAC/PHY 3690 * @phy: the PHY to setup 3691 * @mac: the MAC to setup 3692 * @lc: the requested link configuration 3693 * 3694 * Set up a port's MAC and PHY according to a desired link configuration. 3695 * - If the PHY can auto-negotiate first decide what to advertise, then 3696 * enable/disable auto-negotiation as desired, and reset. 3697 * - If the PHY does not auto-negotiate just reset it. 3698 * - If auto-negotiation is off set the MAC to the proper speed/duplex/FC, 3699 * otherwise do it later based on the outcome of auto-negotiation. 3700 */ 3701int t4_link_l1cfg(struct adapter *adap, unsigned int mbox, unsigned int port, 3702 struct link_config *lc) 3703{ 3704 struct fw_port_cmd c; 3705 unsigned int mdi = V_FW_PORT_CAP_MDI(FW_PORT_CAP_MDI_AUTO); 3706 unsigned int aneg, fc, fec, speed, rcap; 3707 3708 fc = 0; 3709 if (lc->requested_fc & PAUSE_RX) 3710 fc |= FW_PORT_CAP_FC_RX; 3711 if (lc->requested_fc & PAUSE_TX) 3712 fc |= FW_PORT_CAP_FC_TX; 3713 3714 fec = 0; 3715 if (lc->requested_fec & FEC_RS) 3716 fec = FW_PORT_CAP_FEC_RS; 3717 else if (lc->requested_fec & FEC_BASER_RS) 3718 fec = FW_PORT_CAP_FEC_BASER_RS; 3719 else if (lc->requested_fec & FEC_RESERVED) 3720 fec = FW_PORT_CAP_FEC_RESERVED; 3721 3722 if (!(lc->supported & FW_PORT_CAP_ANEG) || 3723 lc->requested_aneg == AUTONEG_DISABLE) { 3724 aneg = 0; 3725 switch (lc->requested_speed) { 3726 case 100: 3727 speed = FW_PORT_CAP_SPEED_100G; 3728 break; 3729 case 40: 3730 speed = FW_PORT_CAP_SPEED_40G; 3731 break; 3732 case 25: 3733 speed = FW_PORT_CAP_SPEED_25G; 3734 break; 3735 case 10: 3736 speed = FW_PORT_CAP_SPEED_10G; 3737 break; 3738 case 1: 3739 speed = FW_PORT_CAP_SPEED_1G; 3740 break; 3741 default: 3742 return -EINVAL; 3743 break; 3744 } 3745 } else { 3746 aneg = FW_PORT_CAP_ANEG; 3747 speed = lc->supported & 3748 V_FW_PORT_CAP_SPEED(M_FW_PORT_CAP_SPEED); 3749 } 3750 3751 rcap = aneg | speed | fc | fec; 3752 if ((rcap | lc->supported) != lc->supported) { 3753#ifdef INVARIANTS 3754 CH_WARN(adap, "rcap 0x%08x, pcap 0x%08x\n", rcap, 3755 lc->supported); 3756#endif 3757 rcap &= lc->supported; 3758 } 3759 rcap |= mdi; 3760 3761 memset(&c, 0, sizeof(c)); 3762 c.op_to_portid = cpu_to_be32(V_FW_CMD_OP(FW_PORT_CMD) | 3763 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 3764 V_FW_PORT_CMD_PORTID(port)); 3765 c.action_to_len16 = 3766 cpu_to_be32(V_FW_PORT_CMD_ACTION(FW_PORT_ACTION_L1_CFG) | 3767 FW_LEN16(c)); 3768 c.u.l1cfg.rcap = cpu_to_be32(rcap); 3769 3770 return t4_wr_mbox_ns(adap, mbox, &c, sizeof(c), NULL); 3771} 3772 3773/** 3774 * t4_restart_aneg - restart autonegotiation 3775 * @adap: the adapter 3776 * @mbox: mbox to use for the FW command 3777 * @port: the port id 3778 * 3779 * Restarts autonegotiation for the selected port. 3780 */ 3781int t4_restart_aneg(struct adapter *adap, unsigned int mbox, unsigned int port) 3782{ 3783 struct fw_port_cmd c; 3784 3785 memset(&c, 0, sizeof(c)); 3786 c.op_to_portid = cpu_to_be32(V_FW_CMD_OP(FW_PORT_CMD) | 3787 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 3788 V_FW_PORT_CMD_PORTID(port)); 3789 c.action_to_len16 = 3790 cpu_to_be32(V_FW_PORT_CMD_ACTION(FW_PORT_ACTION_L1_CFG) | 3791 FW_LEN16(c)); 3792 c.u.l1cfg.rcap = cpu_to_be32(FW_PORT_CAP_ANEG); 3793 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 3794} 3795 3796typedef void (*int_handler_t)(struct adapter *adap); 3797 3798struct intr_info { 3799 unsigned int mask; /* bits to check in interrupt status */ 3800 const char *msg; /* message to print or NULL */ 3801 short stat_idx; /* stat counter to increment or -1 */ 3802 unsigned short fatal; /* whether the condition reported is fatal */ 3803 int_handler_t int_handler; /* platform-specific int handler */ 3804}; 3805 3806/** 3807 * t4_handle_intr_status - table driven interrupt handler 3808 * @adapter: the adapter that generated the interrupt 3809 * @reg: the interrupt status register to process 3810 * @acts: table of interrupt actions 3811 * 3812 * A table driven interrupt handler that applies a set of masks to an 3813 * interrupt status word and performs the corresponding actions if the 3814 * interrupts described by the mask have occurred. The actions include 3815 * optionally emitting a warning or alert message. The table is terminated 3816 * by an entry specifying mask 0. Returns the number of fatal interrupt 3817 * conditions. 3818 */ 3819static int t4_handle_intr_status(struct adapter *adapter, unsigned int reg, 3820 const struct intr_info *acts) 3821{ 3822 int fatal = 0; 3823 unsigned int mask = 0; 3824 unsigned int status = t4_read_reg(adapter, reg); 3825 3826 for ( ; acts->mask; ++acts) { 3827 if (!(status & acts->mask)) 3828 continue; 3829 if (acts->fatal) { 3830 fatal++; 3831 CH_ALERT(adapter, "%s (0x%x)\n", acts->msg, 3832 status & acts->mask); 3833 } else if (acts->msg) 3834 CH_WARN_RATELIMIT(adapter, "%s (0x%x)\n", acts->msg, 3835 status & acts->mask); 3836 if (acts->int_handler) 3837 acts->int_handler(adapter); 3838 mask |= acts->mask; 3839 } 3840 status &= mask; 3841 if (status) /* clear processed interrupts */ 3842 t4_write_reg(adapter, reg, status); 3843 return fatal; 3844} 3845 3846/* 3847 * Interrupt handler for the PCIE module. 3848 */ 3849static void pcie_intr_handler(struct adapter *adapter) 3850{ 3851 static const struct intr_info sysbus_intr_info[] = { 3852 { F_RNPP, "RXNP array parity error", -1, 1 }, 3853 { F_RPCP, "RXPC array parity error", -1, 1 }, 3854 { F_RCIP, "RXCIF array parity error", -1, 1 }, 3855 { F_RCCP, "Rx completions control array parity error", -1, 1 }, 3856 { F_RFTP, "RXFT array parity error", -1, 1 }, 3857 { 0 } 3858 }; 3859 static const struct intr_info pcie_port_intr_info[] = { 3860 { F_TPCP, "TXPC array parity error", -1, 1 }, 3861 { F_TNPP, "TXNP array parity error", -1, 1 }, 3862 { F_TFTP, "TXFT array parity error", -1, 1 }, 3863 { F_TCAP, "TXCA array parity error", -1, 1 }, 3864 { F_TCIP, "TXCIF array parity error", -1, 1 }, 3865 { F_RCAP, "RXCA array parity error", -1, 1 }, 3866 { F_OTDD, "outbound request TLP discarded", -1, 1 }, 3867 { F_RDPE, "Rx data parity error", -1, 1 }, 3868 { F_TDUE, "Tx uncorrectable data error", -1, 1 }, 3869 { 0 } 3870 }; 3871 static const struct intr_info pcie_intr_info[] = { 3872 { F_MSIADDRLPERR, "MSI AddrL parity error", -1, 1 }, 3873 { F_MSIADDRHPERR, "MSI AddrH parity error", -1, 1 }, 3874 { F_MSIDATAPERR, "MSI data parity error", -1, 1 }, 3875 { F_MSIXADDRLPERR, "MSI-X AddrL parity error", -1, 1 }, 3876 { F_MSIXADDRHPERR, "MSI-X AddrH parity error", -1, 1 }, 3877 { F_MSIXDATAPERR, "MSI-X data parity error", -1, 1 }, 3878 { F_MSIXDIPERR, "MSI-X DI parity error", -1, 1 }, 3879 { F_PIOCPLPERR, "PCI PIO completion FIFO parity error", -1, 1 }, 3880 { F_PIOREQPERR, "PCI PIO request FIFO parity error", -1, 1 }, 3881 { F_TARTAGPERR, "PCI PCI target tag FIFO parity error", -1, 1 }, 3882 { F_CCNTPERR, "PCI CMD channel count parity error", -1, 1 }, 3883 { F_CREQPERR, "PCI CMD channel request parity error", -1, 1 }, 3884 { F_CRSPPERR, "PCI CMD channel response parity error", -1, 1 }, 3885 { F_DCNTPERR, "PCI DMA channel count parity error", -1, 1 }, 3886 { F_DREQPERR, "PCI DMA channel request parity error", -1, 1 }, 3887 { F_DRSPPERR, "PCI DMA channel response parity error", -1, 1 }, 3888 { F_HCNTPERR, "PCI HMA channel count parity error", -1, 1 }, 3889 { F_HREQPERR, "PCI HMA channel request parity error", -1, 1 }, 3890 { F_HRSPPERR, "PCI HMA channel response parity error", -1, 1 }, 3891 { F_CFGSNPPERR, "PCI config snoop FIFO parity error", -1, 1 }, 3892 { F_FIDPERR, "PCI FID parity error", -1, 1 }, 3893 { F_INTXCLRPERR, "PCI INTx clear parity error", -1, 1 }, 3894 { F_MATAGPERR, "PCI MA tag parity error", -1, 1 }, 3895 { F_PIOTAGPERR, "PCI PIO tag parity error", -1, 1 }, 3896 { F_RXCPLPERR, "PCI Rx completion parity error", -1, 1 }, 3897 { F_RXWRPERR, "PCI Rx write parity error", -1, 1 }, 3898 { F_RPLPERR, "PCI replay buffer parity error", -1, 1 }, 3899 { F_PCIESINT, "PCI core secondary fault", -1, 1 }, 3900 { F_PCIEPINT, "PCI core primary fault", -1, 1 }, 3901 { F_UNXSPLCPLERR, "PCI unexpected split completion error", -1, 3902 0 }, 3903 { 0 } 3904 }; 3905 3906 static const struct intr_info t5_pcie_intr_info[] = { 3907 { F_MSTGRPPERR, "Master Response Read Queue parity error", 3908 -1, 1 }, 3909 { F_MSTTIMEOUTPERR, "Master Timeout FIFO parity error", -1, 1 }, 3910 { F_MSIXSTIPERR, "MSI-X STI SRAM parity error", -1, 1 }, 3911 { F_MSIXADDRLPERR, "MSI-X AddrL parity error", -1, 1 }, 3912 { F_MSIXADDRHPERR, "MSI-X AddrH parity error", -1, 1 }, 3913 { F_MSIXDATAPERR, "MSI-X data parity error", -1, 1 }, 3914 { F_MSIXDIPERR, "MSI-X DI parity error", -1, 1 }, 3915 { F_PIOCPLGRPPERR, "PCI PIO completion Group FIFO parity error", 3916 -1, 1 }, 3917 { F_PIOREQGRPPERR, "PCI PIO request Group FIFO parity error", 3918 -1, 1 }, 3919 { F_TARTAGPERR, "PCI PCI target tag FIFO parity error", -1, 1 }, 3920 { F_MSTTAGQPERR, "PCI master tag queue parity error", -1, 1 }, 3921 { F_CREQPERR, "PCI CMD channel request parity error", -1, 1 }, 3922 { F_CRSPPERR, "PCI CMD channel response parity error", -1, 1 }, 3923 { F_DREQWRPERR, "PCI DMA channel write request parity error", 3924 -1, 1 }, 3925 { F_DREQPERR, "PCI DMA channel request parity error", -1, 1 }, 3926 { F_DRSPPERR, "PCI DMA channel response parity error", -1, 1 }, 3927 { F_HREQWRPERR, "PCI HMA channel count parity error", -1, 1 }, 3928 { F_HREQPERR, "PCI HMA channel request parity error", -1, 1 }, 3929 { F_HRSPPERR, "PCI HMA channel response parity error", -1, 1 }, 3930 { F_CFGSNPPERR, "PCI config snoop FIFO parity error", -1, 1 }, 3931 { F_FIDPERR, "PCI FID parity error", -1, 1 }, 3932 { F_VFIDPERR, "PCI INTx clear parity error", -1, 1 }, 3933 { F_MAGRPPERR, "PCI MA group FIFO parity error", -1, 1 }, 3934 { F_PIOTAGPERR, "PCI PIO tag parity error", -1, 1 }, 3935 { F_IPRXHDRGRPPERR, "PCI IP Rx header group parity error", 3936 -1, 1 }, 3937 { F_IPRXDATAGRPPERR, "PCI IP Rx data group parity error", 3938 -1, 1 }, 3939 { F_RPLPERR, "PCI IP replay buffer parity error", -1, 1 }, 3940 { F_IPSOTPERR, "PCI IP SOT buffer parity error", -1, 1 }, 3941 { F_TRGT1GRPPERR, "PCI TRGT1 group FIFOs parity error", -1, 1 }, 3942 { F_READRSPERR, "Outbound read error", -1, 3943 0 }, 3944 { 0 } 3945 }; 3946 3947 int fat; 3948 3949 if (is_t4(adapter)) 3950 fat = t4_handle_intr_status(adapter, 3951 A_PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS, 3952 sysbus_intr_info) + 3953 t4_handle_intr_status(adapter, 3954 A_PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS, 3955 pcie_port_intr_info) + 3956 t4_handle_intr_status(adapter, A_PCIE_INT_CAUSE, 3957 pcie_intr_info); 3958 else 3959 fat = t4_handle_intr_status(adapter, A_PCIE_INT_CAUSE, 3960 t5_pcie_intr_info); 3961 if (fat) 3962 t4_fatal_err(adapter); 3963} 3964 3965/* 3966 * TP interrupt handler. 3967 */ 3968static void tp_intr_handler(struct adapter *adapter) 3969{ 3970 static const struct intr_info tp_intr_info[] = { 3971 { 0x3fffffff, "TP parity error", -1, 1 }, 3972 { F_FLMTXFLSTEMPTY, "TP out of Tx pages", -1, 1 }, 3973 { 0 } 3974 }; 3975 3976 if (t4_handle_intr_status(adapter, A_TP_INT_CAUSE, tp_intr_info)) 3977 t4_fatal_err(adapter); 3978} 3979 3980/* 3981 * SGE interrupt handler. 3982 */ 3983static void sge_intr_handler(struct adapter *adapter) 3984{ 3985 u64 v; 3986 u32 err; 3987 3988 static const struct intr_info sge_intr_info[] = { 3989 { F_ERR_CPL_EXCEED_IQE_SIZE, 3990 "SGE received CPL exceeding IQE size", -1, 1 }, 3991 { F_ERR_INVALID_CIDX_INC, 3992 "SGE GTS CIDX increment too large", -1, 0 }, 3993 { F_ERR_CPL_OPCODE_0, "SGE received 0-length CPL", -1, 0 }, 3994 { F_DBFIFO_LP_INT, NULL, -1, 0, t4_db_full }, 3995 { F_ERR_DATA_CPL_ON_HIGH_QID1 | F_ERR_DATA_CPL_ON_HIGH_QID0, 3996 "SGE IQID > 1023 received CPL for FL", -1, 0 }, 3997 { F_ERR_BAD_DB_PIDX3, "SGE DBP 3 pidx increment too large", -1, 3998 0 }, 3999 { F_ERR_BAD_DB_PIDX2, "SGE DBP 2 pidx increment too large", -1, 4000 0 }, 4001 { F_ERR_BAD_DB_PIDX1, "SGE DBP 1 pidx increment too large", -1, 4002 0 }, 4003 { F_ERR_BAD_DB_PIDX0, "SGE DBP 0 pidx increment too large", -1, 4004 0 }, 4005 { F_ERR_ING_CTXT_PRIO, 4006 "SGE too many priority ingress contexts", -1, 0 }, 4007 { F_INGRESS_SIZE_ERR, "SGE illegal ingress QID", -1, 0 }, 4008 { F_EGRESS_SIZE_ERR, "SGE illegal egress QID", -1, 0 }, 4009 { F_ERR_PCIE_ERROR0 | F_ERR_PCIE_ERROR1 | 4010 F_ERR_PCIE_ERROR2 | F_ERR_PCIE_ERROR3, 4011 "SGE PCIe error for a DBP thread", -1, 0 }, 4012 { 0 } 4013 }; 4014 4015 static const struct intr_info t4t5_sge_intr_info[] = { 4016 { F_ERR_DROPPED_DB, NULL, -1, 0, t4_db_dropped }, 4017 { F_DBFIFO_HP_INT, NULL, -1, 0, t4_db_full }, 4018 { F_ERR_EGR_CTXT_PRIO, 4019 "SGE too many priority egress contexts", -1, 0 }, 4020 { 0 } 4021 }; 4022 4023 /* 4024 * For now, treat below interrupts as fatal so that we disable SGE and 4025 * get better debug */ 4026 static const struct intr_info t6_sge_intr_info[] = { 4027 { F_FATAL_WRE_LEN, 4028 "SGE Actual WRE packet is less than advertized length", 4029 -1, 1 }, 4030 { 0 } 4031 }; 4032 4033 v = (u64)t4_read_reg(adapter, A_SGE_INT_CAUSE1) | 4034 ((u64)t4_read_reg(adapter, A_SGE_INT_CAUSE2) << 32); 4035 if (v) { 4036 CH_ALERT(adapter, "SGE parity error (%#llx)\n", 4037 (unsigned long long)v); 4038 t4_write_reg(adapter, A_SGE_INT_CAUSE1, v); 4039 t4_write_reg(adapter, A_SGE_INT_CAUSE2, v >> 32); 4040 } 4041 4042 v |= t4_handle_intr_status(adapter, A_SGE_INT_CAUSE3, sge_intr_info); 4043 if (chip_id(adapter) <= CHELSIO_T5) 4044 v |= t4_handle_intr_status(adapter, A_SGE_INT_CAUSE3, 4045 t4t5_sge_intr_info); 4046 else 4047 v |= t4_handle_intr_status(adapter, A_SGE_INT_CAUSE3, 4048 t6_sge_intr_info); 4049 4050 err = t4_read_reg(adapter, A_SGE_ERROR_STATS); 4051 if (err & F_ERROR_QID_VALID) { 4052 CH_ERR(adapter, "SGE error for queue %u\n", G_ERROR_QID(err)); 4053 if (err & F_UNCAPTURED_ERROR) 4054 CH_ERR(adapter, "SGE UNCAPTURED_ERROR set (clearing)\n"); 4055 t4_write_reg(adapter, A_SGE_ERROR_STATS, F_ERROR_QID_VALID | 4056 F_UNCAPTURED_ERROR); 4057 } 4058 4059 if (v != 0) 4060 t4_fatal_err(adapter); 4061} 4062 4063#define CIM_OBQ_INTR (F_OBQULP0PARERR | F_OBQULP1PARERR | F_OBQULP2PARERR |\ 4064 F_OBQULP3PARERR | F_OBQSGEPARERR | F_OBQNCSIPARERR) 4065#define CIM_IBQ_INTR (F_IBQTP0PARERR | F_IBQTP1PARERR | F_IBQULPPARERR |\ 4066 F_IBQSGEHIPARERR | F_IBQSGELOPARERR | F_IBQNCSIPARERR) 4067 4068/* 4069 * CIM interrupt handler. 4070 */ 4071static void cim_intr_handler(struct adapter *adapter) 4072{ 4073 static const struct intr_info cim_intr_info[] = { 4074 { F_PREFDROPINT, "CIM control register prefetch drop", -1, 1 }, 4075 { CIM_OBQ_INTR, "CIM OBQ parity error", -1, 1 }, 4076 { CIM_IBQ_INTR, "CIM IBQ parity error", -1, 1 }, 4077 { F_MBUPPARERR, "CIM mailbox uP parity error", -1, 1 }, 4078 { F_MBHOSTPARERR, "CIM mailbox host parity error", -1, 1 }, 4079 { F_TIEQINPARERRINT, "CIM TIEQ outgoing parity error", -1, 1 }, 4080 { F_TIEQOUTPARERRINT, "CIM TIEQ incoming parity error", -1, 1 }, 4081 { F_TIMER0INT, "CIM TIMER0 interrupt", -1, 1 }, 4082 { 0 } 4083 }; 4084 static const struct intr_info cim_upintr_info[] = { 4085 { F_RSVDSPACEINT, "CIM reserved space access", -1, 1 }, 4086 { F_ILLTRANSINT, "CIM illegal transaction", -1, 1 }, 4087 { F_ILLWRINT, "CIM illegal write", -1, 1 }, 4088 { F_ILLRDINT, "CIM illegal read", -1, 1 }, 4089 { F_ILLRDBEINT, "CIM illegal read BE", -1, 1 }, 4090 { F_ILLWRBEINT, "CIM illegal write BE", -1, 1 }, 4091 { F_SGLRDBOOTINT, "CIM single read from boot space", -1, 1 }, 4092 { F_SGLWRBOOTINT, "CIM single write to boot space", -1, 1 }, 4093 { F_BLKWRBOOTINT, "CIM block write to boot space", -1, 1 }, 4094 { F_SGLRDFLASHINT, "CIM single read from flash space", -1, 1 }, 4095 { F_SGLWRFLASHINT, "CIM single write to flash space", -1, 1 }, 4096 { F_BLKWRFLASHINT, "CIM block write to flash space", -1, 1 }, 4097 { F_SGLRDEEPROMINT, "CIM single EEPROM read", -1, 1 }, 4098 { F_SGLWREEPROMINT, "CIM single EEPROM write", -1, 1 }, 4099 { F_BLKRDEEPROMINT, "CIM block EEPROM read", -1, 1 }, 4100 { F_BLKWREEPROMINT, "CIM block EEPROM write", -1, 1 }, 4101 { F_SGLRDCTLINT , "CIM single read from CTL space", -1, 1 }, 4102 { F_SGLWRCTLINT , "CIM single write to CTL space", -1, 1 }, 4103 { F_BLKRDCTLINT , "CIM block read from CTL space", -1, 1 }, 4104 { F_BLKWRCTLINT , "CIM block write to CTL space", -1, 1 }, 4105 { F_SGLRDPLINT , "CIM single read from PL space", -1, 1 }, 4106 { F_SGLWRPLINT , "CIM single write to PL space", -1, 1 }, 4107 { F_BLKRDPLINT , "CIM block read from PL space", -1, 1 }, 4108 { F_BLKWRPLINT , "CIM block write to PL space", -1, 1 }, 4109 { F_REQOVRLOOKUPINT , "CIM request FIFO overwrite", -1, 1 }, 4110 { F_RSPOVRLOOKUPINT , "CIM response FIFO overwrite", -1, 1 }, 4111 { F_TIMEOUTINT , "CIM PIF timeout", -1, 1 }, 4112 { F_TIMEOUTMAINT , "CIM PIF MA timeout", -1, 1 }, 4113 { 0 } 4114 }; 4115 u32 val, fw_err; 4116 int fat; 4117 4118 fw_err = t4_read_reg(adapter, A_PCIE_FW); 4119 if (fw_err & F_PCIE_FW_ERR) 4120 t4_report_fw_error(adapter); 4121 4122 /* When the Firmware detects an internal error which normally wouldn't 4123 * raise a Host Interrupt, it forces a CIM Timer0 interrupt in order 4124 * to make sure the Host sees the Firmware Crash. So if we have a 4125 * Timer0 interrupt and don't see a Firmware Crash, ignore the Timer0 4126 * interrupt. 4127 */ 4128 val = t4_read_reg(adapter, A_CIM_HOST_INT_CAUSE); 4129 if (val & F_TIMER0INT) 4130 if (!(fw_err & F_PCIE_FW_ERR) || 4131 (G_PCIE_FW_EVAL(fw_err) != PCIE_FW_EVAL_CRASH)) 4132 t4_write_reg(adapter, A_CIM_HOST_INT_CAUSE, 4133 F_TIMER0INT); 4134 4135 fat = t4_handle_intr_status(adapter, A_CIM_HOST_INT_CAUSE, 4136 cim_intr_info) + 4137 t4_handle_intr_status(adapter, A_CIM_HOST_UPACC_INT_CAUSE, 4138 cim_upintr_info); 4139 if (fat) 4140 t4_fatal_err(adapter); 4141} 4142 4143/* 4144 * ULP RX interrupt handler. 4145 */ 4146static void ulprx_intr_handler(struct adapter *adapter) 4147{ 4148 static const struct intr_info ulprx_intr_info[] = { 4149 { F_CAUSE_CTX_1, "ULPRX channel 1 context error", -1, 1 }, 4150 { F_CAUSE_CTX_0, "ULPRX channel 0 context error", -1, 1 }, 4151 { 0x7fffff, "ULPRX parity error", -1, 1 }, 4152 { 0 } 4153 }; 4154 4155 if (t4_handle_intr_status(adapter, A_ULP_RX_INT_CAUSE, ulprx_intr_info)) 4156 t4_fatal_err(adapter); 4157} 4158 4159/* 4160 * ULP TX interrupt handler. 4161 */ 4162static void ulptx_intr_handler(struct adapter *adapter) 4163{ 4164 static const struct intr_info ulptx_intr_info[] = { 4165 { F_PBL_BOUND_ERR_CH3, "ULPTX channel 3 PBL out of bounds", -1, 4166 0 }, 4167 { F_PBL_BOUND_ERR_CH2, "ULPTX channel 2 PBL out of bounds", -1, 4168 0 }, 4169 { F_PBL_BOUND_ERR_CH1, "ULPTX channel 1 PBL out of bounds", -1, 4170 0 }, 4171 { F_PBL_BOUND_ERR_CH0, "ULPTX channel 0 PBL out of bounds", -1, 4172 0 }, 4173 { 0xfffffff, "ULPTX parity error", -1, 1 }, 4174 { 0 } 4175 }; 4176 4177 if (t4_handle_intr_status(adapter, A_ULP_TX_INT_CAUSE, ulptx_intr_info)) 4178 t4_fatal_err(adapter); 4179} 4180 4181/* 4182 * PM TX interrupt handler. 4183 */ 4184static void pmtx_intr_handler(struct adapter *adapter) 4185{ 4186 static const struct intr_info pmtx_intr_info[] = { 4187 { F_PCMD_LEN_OVFL0, "PMTX channel 0 pcmd too large", -1, 1 }, 4188 { F_PCMD_LEN_OVFL1, "PMTX channel 1 pcmd too large", -1, 1 }, 4189 { F_PCMD_LEN_OVFL2, "PMTX channel 2 pcmd too large", -1, 1 }, 4190 { F_ZERO_C_CMD_ERROR, "PMTX 0-length pcmd", -1, 1 }, 4191 { 0xffffff0, "PMTX framing error", -1, 1 }, 4192 { F_OESPI_PAR_ERROR, "PMTX oespi parity error", -1, 1 }, 4193 { F_DB_OPTIONS_PAR_ERROR, "PMTX db_options parity error", -1, 4194 1 }, 4195 { F_ICSPI_PAR_ERROR, "PMTX icspi parity error", -1, 1 }, 4196 { F_C_PCMD_PAR_ERROR, "PMTX c_pcmd parity error", -1, 1}, 4197 { 0 } 4198 }; 4199 4200 if (t4_handle_intr_status(adapter, A_PM_TX_INT_CAUSE, pmtx_intr_info)) 4201 t4_fatal_err(adapter); 4202} 4203 4204/* 4205 * PM RX interrupt handler. 4206 */ 4207static void pmrx_intr_handler(struct adapter *adapter) 4208{ 4209 static const struct intr_info pmrx_intr_info[] = { 4210 { F_ZERO_E_CMD_ERROR, "PMRX 0-length pcmd", -1, 1 }, 4211 { 0x3ffff0, "PMRX framing error", -1, 1 }, 4212 { F_OCSPI_PAR_ERROR, "PMRX ocspi parity error", -1, 1 }, 4213 { F_DB_OPTIONS_PAR_ERROR, "PMRX db_options parity error", -1, 4214 1 }, 4215 { F_IESPI_PAR_ERROR, "PMRX iespi parity error", -1, 1 }, 4216 { F_E_PCMD_PAR_ERROR, "PMRX e_pcmd parity error", -1, 1}, 4217 { 0 } 4218 }; 4219 4220 if (t4_handle_intr_status(adapter, A_PM_RX_INT_CAUSE, pmrx_intr_info)) 4221 t4_fatal_err(adapter); 4222} 4223 4224/* 4225 * CPL switch interrupt handler. 4226 */ 4227static void cplsw_intr_handler(struct adapter *adapter) 4228{ 4229 static const struct intr_info cplsw_intr_info[] = { 4230 { F_CIM_OP_MAP_PERR, "CPLSW CIM op_map parity error", -1, 1 }, 4231 { F_CIM_OVFL_ERROR, "CPLSW CIM overflow", -1, 1 }, 4232 { F_TP_FRAMING_ERROR, "CPLSW TP framing error", -1, 1 }, 4233 { F_SGE_FRAMING_ERROR, "CPLSW SGE framing error", -1, 1 }, 4234 { F_CIM_FRAMING_ERROR, "CPLSW CIM framing error", -1, 1 }, 4235 { F_ZERO_SWITCH_ERROR, "CPLSW no-switch error", -1, 1 }, 4236 { 0 } 4237 }; 4238 4239 if (t4_handle_intr_status(adapter, A_CPL_INTR_CAUSE, cplsw_intr_info)) 4240 t4_fatal_err(adapter); 4241} 4242 4243/* 4244 * LE interrupt handler. 4245 */ 4246static void le_intr_handler(struct adapter *adap) 4247{ 4248 unsigned int chip_ver = chip_id(adap); 4249 static const struct intr_info le_intr_info[] = { 4250 { F_LIPMISS, "LE LIP miss", -1, 0 }, 4251 { F_LIP0, "LE 0 LIP error", -1, 0 }, 4252 { F_PARITYERR, "LE parity error", -1, 1 }, 4253 { F_UNKNOWNCMD, "LE unknown command", -1, 1 }, 4254 { F_REQQPARERR, "LE request queue parity error", -1, 1 }, 4255 { 0 } 4256 }; 4257 4258 static const struct intr_info t6_le_intr_info[] = { 4259 { F_T6_LIPMISS, "LE LIP miss", -1, 0 }, 4260 { F_T6_LIP0, "LE 0 LIP error", -1, 0 }, 4261 { F_TCAMINTPERR, "LE parity error", -1, 1 }, 4262 { F_T6_UNKNOWNCMD, "LE unknown command", -1, 1 }, 4263 { F_SSRAMINTPERR, "LE request queue parity error", -1, 1 }, 4264 { 0 } 4265 }; 4266 4267 if (t4_handle_intr_status(adap, A_LE_DB_INT_CAUSE, 4268 (chip_ver <= CHELSIO_T5) ? 4269 le_intr_info : t6_le_intr_info)) 4270 t4_fatal_err(adap); 4271} 4272 4273/* 4274 * MPS interrupt handler. 4275 */ 4276static void mps_intr_handler(struct adapter *adapter) 4277{ 4278 static const struct intr_info mps_rx_intr_info[] = { 4279 { 0xffffff, "MPS Rx parity error", -1, 1 }, 4280 { 0 } 4281 }; 4282 static const struct intr_info mps_tx_intr_info[] = { 4283 { V_TPFIFO(M_TPFIFO), "MPS Tx TP FIFO parity error", -1, 1 }, 4284 { F_NCSIFIFO, "MPS Tx NC-SI FIFO parity error", -1, 1 }, 4285 { V_TXDATAFIFO(M_TXDATAFIFO), "MPS Tx data FIFO parity error", 4286 -1, 1 }, 4287 { V_TXDESCFIFO(M_TXDESCFIFO), "MPS Tx desc FIFO parity error", 4288 -1, 1 }, 4289 { F_BUBBLE, "MPS Tx underflow", -1, 1 }, 4290 { F_SECNTERR, "MPS Tx SOP/EOP error", -1, 1 }, 4291 { F_FRMERR, "MPS Tx framing error", -1, 1 }, 4292 { 0 } 4293 }; 4294 static const struct intr_info mps_trc_intr_info[] = { 4295 { V_FILTMEM(M_FILTMEM), "MPS TRC filter parity error", -1, 1 }, 4296 { V_PKTFIFO(M_PKTFIFO), "MPS TRC packet FIFO parity error", -1, 4297 1 }, 4298 { F_MISCPERR, "MPS TRC misc parity error", -1, 1 }, 4299 { 0 } 4300 }; 4301 static const struct intr_info mps_stat_sram_intr_info[] = { 4302 { 0x1fffff, "MPS statistics SRAM parity error", -1, 1 }, 4303 { 0 } 4304 }; 4305 static const struct intr_info mps_stat_tx_intr_info[] = { 4306 { 0xfffff, "MPS statistics Tx FIFO parity error", -1, 1 }, 4307 { 0 } 4308 }; 4309 static const struct intr_info mps_stat_rx_intr_info[] = { 4310 { 0xffffff, "MPS statistics Rx FIFO parity error", -1, 1 }, 4311 { 0 } 4312 }; 4313 static const struct intr_info mps_cls_intr_info[] = { 4314 { F_MATCHSRAM, "MPS match SRAM parity error", -1, 1 }, 4315 { F_MATCHTCAM, "MPS match TCAM parity error", -1, 1 }, 4316 { F_HASHSRAM, "MPS hash SRAM parity error", -1, 1 }, 4317 { 0 } 4318 }; 4319 4320 int fat; 4321 4322 fat = t4_handle_intr_status(adapter, A_MPS_RX_PERR_INT_CAUSE, 4323 mps_rx_intr_info) + 4324 t4_handle_intr_status(adapter, A_MPS_TX_INT_CAUSE, 4325 mps_tx_intr_info) + 4326 t4_handle_intr_status(adapter, A_MPS_TRC_INT_CAUSE, 4327 mps_trc_intr_info) + 4328 t4_handle_intr_status(adapter, A_MPS_STAT_PERR_INT_CAUSE_SRAM, 4329 mps_stat_sram_intr_info) + 4330 t4_handle_intr_status(adapter, A_MPS_STAT_PERR_INT_CAUSE_TX_FIFO, 4331 mps_stat_tx_intr_info) + 4332 t4_handle_intr_status(adapter, A_MPS_STAT_PERR_INT_CAUSE_RX_FIFO, 4333 mps_stat_rx_intr_info) + 4334 t4_handle_intr_status(adapter, A_MPS_CLS_INT_CAUSE, 4335 mps_cls_intr_info); 4336 4337 t4_write_reg(adapter, A_MPS_INT_CAUSE, 0); 4338 t4_read_reg(adapter, A_MPS_INT_CAUSE); /* flush */ 4339 if (fat) 4340 t4_fatal_err(adapter); 4341} 4342 4343#define MEM_INT_MASK (F_PERR_INT_CAUSE | F_ECC_CE_INT_CAUSE | \ 4344 F_ECC_UE_INT_CAUSE) 4345 4346/* 4347 * EDC/MC interrupt handler. 4348 */ 4349static void mem_intr_handler(struct adapter *adapter, int idx) 4350{ 4351 static const char name[4][7] = { "EDC0", "EDC1", "MC/MC0", "MC1" }; 4352 4353 unsigned int addr, cnt_addr, v; 4354 4355 if (idx <= MEM_EDC1) { 4356 addr = EDC_REG(A_EDC_INT_CAUSE, idx); 4357 cnt_addr = EDC_REG(A_EDC_ECC_STATUS, idx); 4358 } else if (idx == MEM_MC) { 4359 if (is_t4(adapter)) { 4360 addr = A_MC_INT_CAUSE; 4361 cnt_addr = A_MC_ECC_STATUS; 4362 } else { 4363 addr = A_MC_P_INT_CAUSE; 4364 cnt_addr = A_MC_P_ECC_STATUS; 4365 } 4366 } else { 4367 addr = MC_REG(A_MC_P_INT_CAUSE, 1); 4368 cnt_addr = MC_REG(A_MC_P_ECC_STATUS, 1); 4369 } 4370 4371 v = t4_read_reg(adapter, addr) & MEM_INT_MASK; 4372 if (v & F_PERR_INT_CAUSE) 4373 CH_ALERT(adapter, "%s FIFO parity error\n", 4374 name[idx]); 4375 if (v & F_ECC_CE_INT_CAUSE) { 4376 u32 cnt = G_ECC_CECNT(t4_read_reg(adapter, cnt_addr)); 4377 4378 if (idx <= MEM_EDC1) 4379 t4_edc_err_read(adapter, idx); 4380 4381 t4_write_reg(adapter, cnt_addr, V_ECC_CECNT(M_ECC_CECNT)); 4382 CH_WARN_RATELIMIT(adapter, 4383 "%u %s correctable ECC data error%s\n", 4384 cnt, name[idx], cnt > 1 ? "s" : ""); 4385 } 4386 if (v & F_ECC_UE_INT_CAUSE) 4387 CH_ALERT(adapter, 4388 "%s uncorrectable ECC data error\n", name[idx]); 4389 4390 t4_write_reg(adapter, addr, v); 4391 if (v & (F_PERR_INT_CAUSE | F_ECC_UE_INT_CAUSE)) 4392 t4_fatal_err(adapter); 4393} 4394 4395/* 4396 * MA interrupt handler. 4397 */ 4398static void ma_intr_handler(struct adapter *adapter) 4399{ 4400 u32 v, status = t4_read_reg(adapter, A_MA_INT_CAUSE); 4401 4402 if (status & F_MEM_PERR_INT_CAUSE) { 4403 CH_ALERT(adapter, 4404 "MA parity error, parity status %#x\n", 4405 t4_read_reg(adapter, A_MA_PARITY_ERROR_STATUS1)); 4406 if (is_t5(adapter)) 4407 CH_ALERT(adapter, 4408 "MA parity error, parity status %#x\n", 4409 t4_read_reg(adapter, 4410 A_MA_PARITY_ERROR_STATUS2)); 4411 } 4412 if (status & F_MEM_WRAP_INT_CAUSE) { 4413 v = t4_read_reg(adapter, A_MA_INT_WRAP_STATUS); 4414 CH_ALERT(adapter, "MA address wrap-around error by " 4415 "client %u to address %#x\n", 4416 G_MEM_WRAP_CLIENT_NUM(v), 4417 G_MEM_WRAP_ADDRESS(v) << 4); 4418 } 4419 t4_write_reg(adapter, A_MA_INT_CAUSE, status); 4420 t4_fatal_err(adapter); 4421} 4422 4423/* 4424 * SMB interrupt handler. 4425 */ 4426static void smb_intr_handler(struct adapter *adap) 4427{ 4428 static const struct intr_info smb_intr_info[] = { 4429 { F_MSTTXFIFOPARINT, "SMB master Tx FIFO parity error", -1, 1 }, 4430 { F_MSTRXFIFOPARINT, "SMB master Rx FIFO parity error", -1, 1 }, 4431 { F_SLVFIFOPARINT, "SMB slave FIFO parity error", -1, 1 }, 4432 { 0 } 4433 }; 4434 4435 if (t4_handle_intr_status(adap, A_SMB_INT_CAUSE, smb_intr_info)) 4436 t4_fatal_err(adap); 4437} 4438 4439/* 4440 * NC-SI interrupt handler. 4441 */ 4442static void ncsi_intr_handler(struct adapter *adap) 4443{ 4444 static const struct intr_info ncsi_intr_info[] = { 4445 { F_CIM_DM_PRTY_ERR, "NC-SI CIM parity error", -1, 1 }, 4446 { F_MPS_DM_PRTY_ERR, "NC-SI MPS parity error", -1, 1 }, 4447 { F_TXFIFO_PRTY_ERR, "NC-SI Tx FIFO parity error", -1, 1 }, 4448 { F_RXFIFO_PRTY_ERR, "NC-SI Rx FIFO parity error", -1, 1 }, 4449 { 0 } 4450 }; 4451 4452 if (t4_handle_intr_status(adap, A_NCSI_INT_CAUSE, ncsi_intr_info)) 4453 t4_fatal_err(adap); 4454} 4455 4456/* 4457 * XGMAC interrupt handler. 4458 */ 4459static void xgmac_intr_handler(struct adapter *adap, int port) 4460{ 4461 u32 v, int_cause_reg; 4462 4463 if (is_t4(adap)) 4464 int_cause_reg = PORT_REG(port, A_XGMAC_PORT_INT_CAUSE); 4465 else 4466 int_cause_reg = T5_PORT_REG(port, A_MAC_PORT_INT_CAUSE); 4467 4468 v = t4_read_reg(adap, int_cause_reg); 4469 4470 v &= (F_TXFIFO_PRTY_ERR | F_RXFIFO_PRTY_ERR); 4471 if (!v) 4472 return; 4473 4474 if (v & F_TXFIFO_PRTY_ERR) 4475 CH_ALERT(adap, "XGMAC %d Tx FIFO parity error\n", 4476 port); 4477 if (v & F_RXFIFO_PRTY_ERR) 4478 CH_ALERT(adap, "XGMAC %d Rx FIFO parity error\n", 4479 port); 4480 t4_write_reg(adap, int_cause_reg, v); 4481 t4_fatal_err(adap); 4482} 4483 4484/* 4485 * PL interrupt handler. 4486 */ 4487static void pl_intr_handler(struct adapter *adap) 4488{ 4489 static const struct intr_info pl_intr_info[] = { 4490 { F_FATALPERR, "Fatal parity error", -1, 1 }, 4491 { F_PERRVFID, "PL VFID_MAP parity error", -1, 1 }, 4492 { 0 } 4493 }; 4494 4495 static const struct intr_info t5_pl_intr_info[] = { 4496 { F_FATALPERR, "Fatal parity error", -1, 1 }, 4497 { 0 } 4498 }; 4499 4500 if (t4_handle_intr_status(adap, A_PL_PL_INT_CAUSE, 4501 is_t4(adap) ? 4502 pl_intr_info : t5_pl_intr_info)) 4503 t4_fatal_err(adap); 4504} 4505 4506#define PF_INTR_MASK (F_PFSW | F_PFCIM) 4507 4508/** 4509 * t4_slow_intr_handler - control path interrupt handler 4510 * @adapter: the adapter 4511 * 4512 * T4 interrupt handler for non-data global interrupt events, e.g., errors. 4513 * The designation 'slow' is because it involves register reads, while 4514 * data interrupts typically don't involve any MMIOs. 4515 */ 4516int t4_slow_intr_handler(struct adapter *adapter) 4517{ 4518 u32 cause = t4_read_reg(adapter, A_PL_INT_CAUSE); 4519 4520 if (!(cause & GLBL_INTR_MASK)) 4521 return 0; 4522 if (cause & F_CIM) 4523 cim_intr_handler(adapter); 4524 if (cause & F_MPS) 4525 mps_intr_handler(adapter); 4526 if (cause & F_NCSI) 4527 ncsi_intr_handler(adapter); 4528 if (cause & F_PL) 4529 pl_intr_handler(adapter); 4530 if (cause & F_SMB) 4531 smb_intr_handler(adapter); 4532 if (cause & F_MAC0) 4533 xgmac_intr_handler(adapter, 0); 4534 if (cause & F_MAC1) 4535 xgmac_intr_handler(adapter, 1); 4536 if (cause & F_MAC2) 4537 xgmac_intr_handler(adapter, 2); 4538 if (cause & F_MAC3) 4539 xgmac_intr_handler(adapter, 3); 4540 if (cause & F_PCIE) 4541 pcie_intr_handler(adapter); 4542 if (cause & F_MC0) 4543 mem_intr_handler(adapter, MEM_MC); 4544 if (is_t5(adapter) && (cause & F_MC1)) 4545 mem_intr_handler(adapter, MEM_MC1); 4546 if (cause & F_EDC0) 4547 mem_intr_handler(adapter, MEM_EDC0); 4548 if (cause & F_EDC1) 4549 mem_intr_handler(adapter, MEM_EDC1); 4550 if (cause & F_LE) 4551 le_intr_handler(adapter); 4552 if (cause & F_TP) 4553 tp_intr_handler(adapter); 4554 if (cause & F_MA) 4555 ma_intr_handler(adapter); 4556 if (cause & F_PM_TX) 4557 pmtx_intr_handler(adapter); 4558 if (cause & F_PM_RX) 4559 pmrx_intr_handler(adapter); 4560 if (cause & F_ULP_RX) 4561 ulprx_intr_handler(adapter); 4562 if (cause & F_CPL_SWITCH) 4563 cplsw_intr_handler(adapter); 4564 if (cause & F_SGE) 4565 sge_intr_handler(adapter); 4566 if (cause & F_ULP_TX) 4567 ulptx_intr_handler(adapter); 4568 4569 /* Clear the interrupts just processed for which we are the master. */ 4570 t4_write_reg(adapter, A_PL_INT_CAUSE, cause & GLBL_INTR_MASK); 4571 (void)t4_read_reg(adapter, A_PL_INT_CAUSE); /* flush */ 4572 return 1; 4573} 4574 4575/** 4576 * t4_intr_enable - enable interrupts 4577 * @adapter: the adapter whose interrupts should be enabled 4578 * 4579 * Enable PF-specific interrupts for the calling function and the top-level 4580 * interrupt concentrator for global interrupts. Interrupts are already 4581 * enabled at each module, here we just enable the roots of the interrupt 4582 * hierarchies. 4583 * 4584 * Note: this function should be called only when the driver manages 4585 * non PF-specific interrupts from the various HW modules. Only one PCI 4586 * function at a time should be doing this. 4587 */ 4588void t4_intr_enable(struct adapter *adapter) 4589{ 4590 u32 val = 0; 4591 u32 whoami = t4_read_reg(adapter, A_PL_WHOAMI); 4592 u32 pf = (chip_id(adapter) <= CHELSIO_T5 4593 ? G_SOURCEPF(whoami) 4594 : G_T6_SOURCEPF(whoami)); 4595 4596 if (chip_id(adapter) <= CHELSIO_T5) 4597 val = F_ERR_DROPPED_DB | F_ERR_EGR_CTXT_PRIO | F_DBFIFO_HP_INT; 4598 else 4599 val = F_ERR_PCIE_ERROR0 | F_ERR_PCIE_ERROR1 | F_FATAL_WRE_LEN; 4600 t4_write_reg(adapter, A_SGE_INT_ENABLE3, F_ERR_CPL_EXCEED_IQE_SIZE | 4601 F_ERR_INVALID_CIDX_INC | F_ERR_CPL_OPCODE_0 | 4602 F_ERR_DATA_CPL_ON_HIGH_QID1 | F_INGRESS_SIZE_ERR | 4603 F_ERR_DATA_CPL_ON_HIGH_QID0 | F_ERR_BAD_DB_PIDX3 | 4604 F_ERR_BAD_DB_PIDX2 | F_ERR_BAD_DB_PIDX1 | 4605 F_ERR_BAD_DB_PIDX0 | F_ERR_ING_CTXT_PRIO | 4606 F_DBFIFO_LP_INT | F_EGRESS_SIZE_ERR | val); 4607 t4_write_reg(adapter, MYPF_REG(A_PL_PF_INT_ENABLE), PF_INTR_MASK); 4608 t4_set_reg_field(adapter, A_PL_INT_MAP0, 0, 1 << pf); 4609} 4610 4611/** 4612 * t4_intr_disable - disable interrupts 4613 * @adapter: the adapter whose interrupts should be disabled 4614 * 4615 * Disable interrupts. We only disable the top-level interrupt 4616 * concentrators. The caller must be a PCI function managing global 4617 * interrupts. 4618 */ 4619void t4_intr_disable(struct adapter *adapter) 4620{ 4621 u32 whoami = t4_read_reg(adapter, A_PL_WHOAMI); 4622 u32 pf = (chip_id(adapter) <= CHELSIO_T5 4623 ? G_SOURCEPF(whoami) 4624 : G_T6_SOURCEPF(whoami)); 4625 4626 t4_write_reg(adapter, MYPF_REG(A_PL_PF_INT_ENABLE), 0); 4627 t4_set_reg_field(adapter, A_PL_INT_MAP0, 1 << pf, 0); 4628} 4629 4630/** 4631 * t4_intr_clear - clear all interrupts 4632 * @adapter: the adapter whose interrupts should be cleared 4633 * 4634 * Clears all interrupts. The caller must be a PCI function managing 4635 * global interrupts. 4636 */ 4637void t4_intr_clear(struct adapter *adapter) 4638{ 4639 static const unsigned int cause_reg[] = { 4640 A_SGE_INT_CAUSE1, A_SGE_INT_CAUSE2, A_SGE_INT_CAUSE3, 4641 A_PCIE_NONFAT_ERR, A_PCIE_INT_CAUSE, 4642 A_MA_INT_WRAP_STATUS, A_MA_PARITY_ERROR_STATUS1, A_MA_INT_CAUSE, 4643 A_EDC_INT_CAUSE, EDC_REG(A_EDC_INT_CAUSE, 1), 4644 A_CIM_HOST_INT_CAUSE, A_CIM_HOST_UPACC_INT_CAUSE, 4645 MYPF_REG(A_CIM_PF_HOST_INT_CAUSE), 4646 A_TP_INT_CAUSE, 4647 A_ULP_RX_INT_CAUSE, A_ULP_TX_INT_CAUSE, 4648 A_PM_RX_INT_CAUSE, A_PM_TX_INT_CAUSE, 4649 A_MPS_RX_PERR_INT_CAUSE, 4650 A_CPL_INTR_CAUSE, 4651 MYPF_REG(A_PL_PF_INT_CAUSE), 4652 A_PL_PL_INT_CAUSE, 4653 A_LE_DB_INT_CAUSE, 4654 }; 4655 4656 unsigned int i; 4657 4658 for (i = 0; i < ARRAY_SIZE(cause_reg); ++i) 4659 t4_write_reg(adapter, cause_reg[i], 0xffffffff); 4660 4661 t4_write_reg(adapter, is_t4(adapter) ? A_MC_INT_CAUSE : 4662 A_MC_P_INT_CAUSE, 0xffffffff); 4663 4664 if (is_t4(adapter)) { 4665 t4_write_reg(adapter, A_PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS, 4666 0xffffffff); 4667 t4_write_reg(adapter, A_PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS, 4668 0xffffffff); 4669 } else 4670 t4_write_reg(adapter, A_MA_PARITY_ERROR_STATUS2, 0xffffffff); 4671 4672 t4_write_reg(adapter, A_PL_INT_CAUSE, GLBL_INTR_MASK); 4673 (void) t4_read_reg(adapter, A_PL_INT_CAUSE); /* flush */ 4674} 4675 4676/** 4677 * hash_mac_addr - return the hash value of a MAC address 4678 * @addr: the 48-bit Ethernet MAC address 4679 * 4680 * Hashes a MAC address according to the hash function used by HW inexact 4681 * (hash) address matching. 4682 */ 4683static int hash_mac_addr(const u8 *addr) 4684{ 4685 u32 a = ((u32)addr[0] << 16) | ((u32)addr[1] << 8) | addr[2]; 4686 u32 b = ((u32)addr[3] << 16) | ((u32)addr[4] << 8) | addr[5]; 4687 a ^= b; 4688 a ^= (a >> 12); 4689 a ^= (a >> 6); 4690 return a & 0x3f; 4691} 4692 4693/** 4694 * t4_config_rss_range - configure a portion of the RSS mapping table 4695 * @adapter: the adapter 4696 * @mbox: mbox to use for the FW command 4697 * @viid: virtual interface whose RSS subtable is to be written 4698 * @start: start entry in the table to write 4699 * @n: how many table entries to write 4700 * @rspq: values for the "response queue" (Ingress Queue) lookup table 4701 * @nrspq: number of values in @rspq 4702 * 4703 * Programs the selected part of the VI's RSS mapping table with the 4704 * provided values. If @nrspq < @n the supplied values are used repeatedly 4705 * until the full table range is populated. 4706 * 4707 * The caller must ensure the values in @rspq are in the range allowed for 4708 * @viid. 4709 */ 4710int t4_config_rss_range(struct adapter *adapter, int mbox, unsigned int viid, 4711 int start, int n, const u16 *rspq, unsigned int nrspq) 4712{ 4713 int ret; 4714 const u16 *rsp = rspq; 4715 const u16 *rsp_end = rspq + nrspq; 4716 struct fw_rss_ind_tbl_cmd cmd; 4717 4718 memset(&cmd, 0, sizeof(cmd)); 4719 cmd.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_RSS_IND_TBL_CMD) | 4720 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 4721 V_FW_RSS_IND_TBL_CMD_VIID(viid)); 4722 cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); 4723 4724 /* 4725 * Each firmware RSS command can accommodate up to 32 RSS Ingress 4726 * Queue Identifiers. These Ingress Queue IDs are packed three to 4727 * a 32-bit word as 10-bit values with the upper remaining 2 bits 4728 * reserved. 4729 */ 4730 while (n > 0) { 4731 int nq = min(n, 32); 4732 int nq_packed = 0; 4733 __be32 *qp = &cmd.iq0_to_iq2; 4734 4735 /* 4736 * Set up the firmware RSS command header to send the next 4737 * "nq" Ingress Queue IDs to the firmware. 4738 */ 4739 cmd.niqid = cpu_to_be16(nq); 4740 cmd.startidx = cpu_to_be16(start); 4741 4742 /* 4743 * "nq" more done for the start of the next loop. 4744 */ 4745 start += nq; 4746 n -= nq; 4747 4748 /* 4749 * While there are still Ingress Queue IDs to stuff into the 4750 * current firmware RSS command, retrieve them from the 4751 * Ingress Queue ID array and insert them into the command. 4752 */ 4753 while (nq > 0) { 4754 /* 4755 * Grab up to the next 3 Ingress Queue IDs (wrapping 4756 * around the Ingress Queue ID array if necessary) and 4757 * insert them into the firmware RSS command at the 4758 * current 3-tuple position within the commad. 4759 */ 4760 u16 qbuf[3]; 4761 u16 *qbp = qbuf; 4762 int nqbuf = min(3, nq); 4763 4764 nq -= nqbuf; 4765 qbuf[0] = qbuf[1] = qbuf[2] = 0; 4766 while (nqbuf && nq_packed < 32) { 4767 nqbuf--; 4768 nq_packed++; 4769 *qbp++ = *rsp++; 4770 if (rsp >= rsp_end) 4771 rsp = rspq; 4772 } 4773 *qp++ = cpu_to_be32(V_FW_RSS_IND_TBL_CMD_IQ0(qbuf[0]) | 4774 V_FW_RSS_IND_TBL_CMD_IQ1(qbuf[1]) | 4775 V_FW_RSS_IND_TBL_CMD_IQ2(qbuf[2])); 4776 } 4777 4778 /* 4779 * Send this portion of the RRS table update to the firmware; 4780 * bail out on any errors. 4781 */ 4782 ret = t4_wr_mbox(adapter, mbox, &cmd, sizeof(cmd), NULL); 4783 if (ret) 4784 return ret; 4785 } 4786 return 0; 4787} 4788 4789/** 4790 * t4_config_glbl_rss - configure the global RSS mode 4791 * @adapter: the adapter 4792 * @mbox: mbox to use for the FW command 4793 * @mode: global RSS mode 4794 * @flags: mode-specific flags 4795 * 4796 * Sets the global RSS mode. 4797 */ 4798int t4_config_glbl_rss(struct adapter *adapter, int mbox, unsigned int mode, 4799 unsigned int flags) 4800{ 4801 struct fw_rss_glb_config_cmd c; 4802 4803 memset(&c, 0, sizeof(c)); 4804 c.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_RSS_GLB_CONFIG_CMD) | 4805 F_FW_CMD_REQUEST | F_FW_CMD_WRITE); 4806 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 4807 if (mode == FW_RSS_GLB_CONFIG_CMD_MODE_MANUAL) { 4808 c.u.manual.mode_pkd = 4809 cpu_to_be32(V_FW_RSS_GLB_CONFIG_CMD_MODE(mode)); 4810 } else if (mode == FW_RSS_GLB_CONFIG_CMD_MODE_BASICVIRTUAL) { 4811 c.u.basicvirtual.mode_keymode = 4812 cpu_to_be32(V_FW_RSS_GLB_CONFIG_CMD_MODE(mode)); 4813 c.u.basicvirtual.synmapen_to_hashtoeplitz = cpu_to_be32(flags); 4814 } else 4815 return -EINVAL; 4816 return t4_wr_mbox(adapter, mbox, &c, sizeof(c), NULL); 4817} 4818 4819/** 4820 * t4_config_vi_rss - configure per VI RSS settings 4821 * @adapter: the adapter 4822 * @mbox: mbox to use for the FW command 4823 * @viid: the VI id 4824 * @flags: RSS flags 4825 * @defq: id of the default RSS queue for the VI. 4826 * @skeyidx: RSS secret key table index for non-global mode 4827 * @skey: RSS vf_scramble key for VI. 4828 * 4829 * Configures VI-specific RSS properties. 4830 */ 4831int t4_config_vi_rss(struct adapter *adapter, int mbox, unsigned int viid, 4832 unsigned int flags, unsigned int defq, unsigned int skeyidx, 4833 unsigned int skey) 4834{ 4835 struct fw_rss_vi_config_cmd c; 4836 4837 memset(&c, 0, sizeof(c)); 4838 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_RSS_VI_CONFIG_CMD) | 4839 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 4840 V_FW_RSS_VI_CONFIG_CMD_VIID(viid)); 4841 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 4842 c.u.basicvirtual.defaultq_to_udpen = cpu_to_be32(flags | 4843 V_FW_RSS_VI_CONFIG_CMD_DEFAULTQ(defq)); 4844 c.u.basicvirtual.secretkeyidx_pkd = cpu_to_be32( 4845 V_FW_RSS_VI_CONFIG_CMD_SECRETKEYIDX(skeyidx)); 4846 c.u.basicvirtual.secretkeyxor = cpu_to_be32(skey); 4847 4848 return t4_wr_mbox(adapter, mbox, &c, sizeof(c), NULL); 4849} 4850 4851/* Read an RSS table row */ 4852static int rd_rss_row(struct adapter *adap, int row, u32 *val) 4853{ 4854 t4_write_reg(adap, A_TP_RSS_LKP_TABLE, 0xfff00000 | row); 4855 return t4_wait_op_done_val(adap, A_TP_RSS_LKP_TABLE, F_LKPTBLROWVLD, 1, 4856 5, 0, val); 4857} 4858 4859/** 4860 * t4_read_rss - read the contents of the RSS mapping table 4861 * @adapter: the adapter 4862 * @map: holds the contents of the RSS mapping table 4863 * 4864 * Reads the contents of the RSS hash->queue mapping table. 4865 */ 4866int t4_read_rss(struct adapter *adapter, u16 *map) 4867{ 4868 u32 val; 4869 int i, ret; 4870 4871 for (i = 0; i < RSS_NENTRIES / 2; ++i) { 4872 ret = rd_rss_row(adapter, i, &val); 4873 if (ret) 4874 return ret; 4875 *map++ = G_LKPTBLQUEUE0(val); 4876 *map++ = G_LKPTBLQUEUE1(val); 4877 } 4878 return 0; 4879} 4880 4881/** 4882 * t4_tp_fw_ldst_rw - Access TP indirect register through LDST 4883 * @adap: the adapter 4884 * @cmd: TP fw ldst address space type 4885 * @vals: where the indirect register values are stored/written 4886 * @nregs: how many indirect registers to read/write 4887 * @start_idx: index of first indirect register to read/write 4888 * @rw: Read (1) or Write (0) 4889 * @sleep_ok: if true we may sleep while awaiting command completion 4890 * 4891 * Access TP indirect registers through LDST 4892 **/ 4893static int t4_tp_fw_ldst_rw(struct adapter *adap, int cmd, u32 *vals, 4894 unsigned int nregs, unsigned int start_index, 4895 unsigned int rw, bool sleep_ok) 4896{ 4897 int ret = 0; 4898 unsigned int i; 4899 struct fw_ldst_cmd c; 4900 4901 for (i = 0; i < nregs; i++) { 4902 memset(&c, 0, sizeof(c)); 4903 c.op_to_addrspace = cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 4904 F_FW_CMD_REQUEST | 4905 (rw ? F_FW_CMD_READ : 4906 F_FW_CMD_WRITE) | 4907 V_FW_LDST_CMD_ADDRSPACE(cmd)); 4908 c.cycles_to_len16 = cpu_to_be32(FW_LEN16(c)); 4909 4910 c.u.addrval.addr = cpu_to_be32(start_index + i); 4911 c.u.addrval.val = rw ? 0 : cpu_to_be32(vals[i]); 4912 ret = t4_wr_mbox_meat(adap, adap->mbox, &c, sizeof(c), &c, 4913 sleep_ok); 4914 if (ret) 4915 return ret; 4916 4917 if (rw) 4918 vals[i] = be32_to_cpu(c.u.addrval.val); 4919 } 4920 return 0; 4921} 4922 4923/** 4924 * t4_tp_indirect_rw - Read/Write TP indirect register through LDST or backdoor 4925 * @adap: the adapter 4926 * @reg_addr: Address Register 4927 * @reg_data: Data register 4928 * @buff: where the indirect register values are stored/written 4929 * @nregs: how many indirect registers to read/write 4930 * @start_index: index of first indirect register to read/write 4931 * @rw: READ(1) or WRITE(0) 4932 * @sleep_ok: if true we may sleep while awaiting command completion 4933 * 4934 * Read/Write TP indirect registers through LDST if possible. 4935 * Else, use backdoor access 4936 **/ 4937static void t4_tp_indirect_rw(struct adapter *adap, u32 reg_addr, u32 reg_data, 4938 u32 *buff, u32 nregs, u32 start_index, int rw, 4939 bool sleep_ok) 4940{ 4941 int rc = -EINVAL; 4942 int cmd; 4943 4944 switch (reg_addr) { 4945 case A_TP_PIO_ADDR: 4946 cmd = FW_LDST_ADDRSPC_TP_PIO; 4947 break; 4948 case A_TP_TM_PIO_ADDR: 4949 cmd = FW_LDST_ADDRSPC_TP_TM_PIO; 4950 break; 4951 case A_TP_MIB_INDEX: 4952 cmd = FW_LDST_ADDRSPC_TP_MIB; 4953 break; 4954 default: 4955 goto indirect_access; 4956 } 4957 4958 if (t4_use_ldst(adap)) 4959 rc = t4_tp_fw_ldst_rw(adap, cmd, buff, nregs, start_index, rw, 4960 sleep_ok); 4961 4962indirect_access: 4963 4964 if (rc) { 4965 if (rw) 4966 t4_read_indirect(adap, reg_addr, reg_data, buff, nregs, 4967 start_index); 4968 else 4969 t4_write_indirect(adap, reg_addr, reg_data, buff, nregs, 4970 start_index); 4971 } 4972} 4973 4974/** 4975 * t4_tp_pio_read - Read TP PIO registers 4976 * @adap: the adapter 4977 * @buff: where the indirect register values are written 4978 * @nregs: how many indirect registers to read 4979 * @start_index: index of first indirect register to read 4980 * @sleep_ok: if true we may sleep while awaiting command completion 4981 * 4982 * Read TP PIO Registers 4983 **/ 4984void t4_tp_pio_read(struct adapter *adap, u32 *buff, u32 nregs, 4985 u32 start_index, bool sleep_ok) 4986{ 4987 t4_tp_indirect_rw(adap, A_TP_PIO_ADDR, A_TP_PIO_DATA, buff, nregs, 4988 start_index, 1, sleep_ok); 4989} 4990 4991/** 4992 * t4_tp_pio_write - Write TP PIO registers 4993 * @adap: the adapter 4994 * @buff: where the indirect register values are stored 4995 * @nregs: how many indirect registers to write 4996 * @start_index: index of first indirect register to write 4997 * @sleep_ok: if true we may sleep while awaiting command completion 4998 * 4999 * Write TP PIO Registers 5000 **/ 5001void t4_tp_pio_write(struct adapter *adap, const u32 *buff, u32 nregs, 5002 u32 start_index, bool sleep_ok) 5003{ 5004 t4_tp_indirect_rw(adap, A_TP_PIO_ADDR, A_TP_PIO_DATA, 5005 __DECONST(u32 *, buff), nregs, start_index, 0, sleep_ok); 5006} 5007 5008/** 5009 * t4_tp_tm_pio_read - Read TP TM PIO registers 5010 * @adap: the adapter 5011 * @buff: where the indirect register values are written 5012 * @nregs: how many indirect registers to read 5013 * @start_index: index of first indirect register to read 5014 * @sleep_ok: if true we may sleep while awaiting command completion 5015 * 5016 * Read TP TM PIO Registers 5017 **/ 5018void t4_tp_tm_pio_read(struct adapter *adap, u32 *buff, u32 nregs, 5019 u32 start_index, bool sleep_ok) 5020{ 5021 t4_tp_indirect_rw(adap, A_TP_TM_PIO_ADDR, A_TP_TM_PIO_DATA, buff, 5022 nregs, start_index, 1, sleep_ok); 5023} 5024 5025/** 5026 * t4_tp_mib_read - Read TP MIB registers 5027 * @adap: the adapter 5028 * @buff: where the indirect register values are written 5029 * @nregs: how many indirect registers to read 5030 * @start_index: index of first indirect register to read 5031 * @sleep_ok: if true we may sleep while awaiting command completion 5032 * 5033 * Read TP MIB Registers 5034 **/ 5035void t4_tp_mib_read(struct adapter *adap, u32 *buff, u32 nregs, u32 start_index, 5036 bool sleep_ok) 5037{ 5038 t4_tp_indirect_rw(adap, A_TP_MIB_INDEX, A_TP_MIB_DATA, buff, nregs, 5039 start_index, 1, sleep_ok); 5040} 5041 5042/** 5043 * t4_read_rss_key - read the global RSS key 5044 * @adap: the adapter 5045 * @key: 10-entry array holding the 320-bit RSS key 5046 * @sleep_ok: if true we may sleep while awaiting command completion 5047 * 5048 * Reads the global 320-bit RSS key. 5049 */ 5050void t4_read_rss_key(struct adapter *adap, u32 *key, bool sleep_ok) 5051{ 5052 t4_tp_pio_read(adap, key, 10, A_TP_RSS_SECRET_KEY0, sleep_ok); 5053} 5054 5055/** 5056 * t4_write_rss_key - program one of the RSS keys 5057 * @adap: the adapter 5058 * @key: 10-entry array holding the 320-bit RSS key 5059 * @idx: which RSS key to write 5060 * @sleep_ok: if true we may sleep while awaiting command completion 5061 * 5062 * Writes one of the RSS keys with the given 320-bit value. If @idx is 5063 * 0..15 the corresponding entry in the RSS key table is written, 5064 * otherwise the global RSS key is written. 5065 */ 5066void t4_write_rss_key(struct adapter *adap, const u32 *key, int idx, 5067 bool sleep_ok) 5068{ 5069 u8 rss_key_addr_cnt = 16; 5070 u32 vrt = t4_read_reg(adap, A_TP_RSS_CONFIG_VRT); 5071 5072 /* 5073 * T6 and later: for KeyMode 3 (per-vf and per-vf scramble), 5074 * allows access to key addresses 16-63 by using KeyWrAddrX 5075 * as index[5:4](upper 2) into key table 5076 */ 5077 if ((chip_id(adap) > CHELSIO_T5) && 5078 (vrt & F_KEYEXTEND) && (G_KEYMODE(vrt) == 3)) 5079 rss_key_addr_cnt = 32; 5080 5081 t4_tp_pio_write(adap, key, 10, A_TP_RSS_SECRET_KEY0, sleep_ok); 5082 5083 if (idx >= 0 && idx < rss_key_addr_cnt) { 5084 if (rss_key_addr_cnt > 16) 5085 t4_write_reg(adap, A_TP_RSS_CONFIG_VRT, 5086 vrt | V_KEYWRADDRX(idx >> 4) | 5087 V_T6_VFWRADDR(idx) | F_KEYWREN); 5088 else 5089 t4_write_reg(adap, A_TP_RSS_CONFIG_VRT, 5090 vrt| V_KEYWRADDR(idx) | F_KEYWREN); 5091 } 5092} 5093 5094/** 5095 * t4_read_rss_pf_config - read PF RSS Configuration Table 5096 * @adapter: the adapter 5097 * @index: the entry in the PF RSS table to read 5098 * @valp: where to store the returned value 5099 * @sleep_ok: if true we may sleep while awaiting command completion 5100 * 5101 * Reads the PF RSS Configuration Table at the specified index and returns 5102 * the value found there. 5103 */ 5104void t4_read_rss_pf_config(struct adapter *adapter, unsigned int index, 5105 u32 *valp, bool sleep_ok) 5106{ 5107 t4_tp_pio_read(adapter, valp, 1, A_TP_RSS_PF0_CONFIG + index, sleep_ok); 5108} 5109 5110/** 5111 * t4_write_rss_pf_config - write PF RSS Configuration Table 5112 * @adapter: the adapter 5113 * @index: the entry in the VF RSS table to read 5114 * @val: the value to store 5115 * @sleep_ok: if true we may sleep while awaiting command completion 5116 * 5117 * Writes the PF RSS Configuration Table at the specified index with the 5118 * specified value. 5119 */ 5120void t4_write_rss_pf_config(struct adapter *adapter, unsigned int index, 5121 u32 val, bool sleep_ok) 5122{ 5123 t4_tp_pio_write(adapter, &val, 1, A_TP_RSS_PF0_CONFIG + index, 5124 sleep_ok); 5125} 5126 5127/** 5128 * t4_read_rss_vf_config - read VF RSS Configuration Table 5129 * @adapter: the adapter 5130 * @index: the entry in the VF RSS table to read 5131 * @vfl: where to store the returned VFL 5132 * @vfh: where to store the returned VFH 5133 * @sleep_ok: if true we may sleep while awaiting command completion 5134 * 5135 * Reads the VF RSS Configuration Table at the specified index and returns 5136 * the (VFL, VFH) values found there. 5137 */ 5138void t4_read_rss_vf_config(struct adapter *adapter, unsigned int index, 5139 u32 *vfl, u32 *vfh, bool sleep_ok) 5140{ 5141 u32 vrt, mask, data; 5142 5143 if (chip_id(adapter) <= CHELSIO_T5) { 5144 mask = V_VFWRADDR(M_VFWRADDR); 5145 data = V_VFWRADDR(index); 5146 } else { 5147 mask = V_T6_VFWRADDR(M_T6_VFWRADDR); 5148 data = V_T6_VFWRADDR(index); 5149 } 5150 /* 5151 * Request that the index'th VF Table values be read into VFL/VFH. 5152 */ 5153 vrt = t4_read_reg(adapter, A_TP_RSS_CONFIG_VRT); 5154 vrt &= ~(F_VFRDRG | F_VFWREN | F_KEYWREN | mask); 5155 vrt |= data | F_VFRDEN; 5156 t4_write_reg(adapter, A_TP_RSS_CONFIG_VRT, vrt); 5157 5158 /* 5159 * Grab the VFL/VFH values ... 5160 */ 5161 t4_tp_pio_read(adapter, vfl, 1, A_TP_RSS_VFL_CONFIG, sleep_ok); 5162 t4_tp_pio_read(adapter, vfh, 1, A_TP_RSS_VFH_CONFIG, sleep_ok); 5163} 5164 5165/** 5166 * t4_write_rss_vf_config - write VF RSS Configuration Table 5167 * 5168 * @adapter: the adapter 5169 * @index: the entry in the VF RSS table to write 5170 * @vfl: the VFL to store 5171 * @vfh: the VFH to store 5172 * 5173 * Writes the VF RSS Configuration Table at the specified index with the 5174 * specified (VFL, VFH) values. 5175 */ 5176void t4_write_rss_vf_config(struct adapter *adapter, unsigned int index, 5177 u32 vfl, u32 vfh, bool sleep_ok) 5178{ 5179 u32 vrt, mask, data; 5180 5181 if (chip_id(adapter) <= CHELSIO_T5) { 5182 mask = V_VFWRADDR(M_VFWRADDR); 5183 data = V_VFWRADDR(index); 5184 } else { 5185 mask = V_T6_VFWRADDR(M_T6_VFWRADDR); 5186 data = V_T6_VFWRADDR(index); 5187 } 5188 5189 /* 5190 * Load up VFL/VFH with the values to be written ... 5191 */ 5192 t4_tp_pio_write(adapter, &vfl, 1, A_TP_RSS_VFL_CONFIG, sleep_ok); 5193 t4_tp_pio_write(adapter, &vfh, 1, A_TP_RSS_VFH_CONFIG, sleep_ok); 5194 5195 /* 5196 * Write the VFL/VFH into the VF Table at index'th location. 5197 */ 5198 vrt = t4_read_reg(adapter, A_TP_RSS_CONFIG_VRT); 5199 vrt &= ~(F_VFRDRG | F_VFWREN | F_KEYWREN | mask); 5200 vrt |= data | F_VFRDEN; 5201 t4_write_reg(adapter, A_TP_RSS_CONFIG_VRT, vrt); 5202} 5203 5204/** 5205 * t4_read_rss_pf_map - read PF RSS Map 5206 * @adapter: the adapter 5207 * @sleep_ok: if true we may sleep while awaiting command completion 5208 * 5209 * Reads the PF RSS Map register and returns its value. 5210 */ 5211u32 t4_read_rss_pf_map(struct adapter *adapter, bool sleep_ok) 5212{ 5213 u32 pfmap; 5214 5215 t4_tp_pio_read(adapter, &pfmap, 1, A_TP_RSS_PF_MAP, sleep_ok); 5216 5217 return pfmap; 5218} 5219 5220/** 5221 * t4_write_rss_pf_map - write PF RSS Map 5222 * @adapter: the adapter 5223 * @pfmap: PF RSS Map value 5224 * 5225 * Writes the specified value to the PF RSS Map register. 5226 */ 5227void t4_write_rss_pf_map(struct adapter *adapter, u32 pfmap, bool sleep_ok) 5228{ 5229 t4_tp_pio_write(adapter, &pfmap, 1, A_TP_RSS_PF_MAP, sleep_ok); 5230} 5231 5232/** 5233 * t4_read_rss_pf_mask - read PF RSS Mask 5234 * @adapter: the adapter 5235 * @sleep_ok: if true we may sleep while awaiting command completion 5236 * 5237 * Reads the PF RSS Mask register and returns its value. 5238 */ 5239u32 t4_read_rss_pf_mask(struct adapter *adapter, bool sleep_ok) 5240{ 5241 u32 pfmask; 5242 5243 t4_tp_pio_read(adapter, &pfmask, 1, A_TP_RSS_PF_MSK, sleep_ok); 5244 5245 return pfmask; 5246} 5247 5248/** 5249 * t4_write_rss_pf_mask - write PF RSS Mask 5250 * @adapter: the adapter 5251 * @pfmask: PF RSS Mask value 5252 * 5253 * Writes the specified value to the PF RSS Mask register. 5254 */ 5255void t4_write_rss_pf_mask(struct adapter *adapter, u32 pfmask, bool sleep_ok) 5256{ 5257 t4_tp_pio_write(adapter, &pfmask, 1, A_TP_RSS_PF_MSK, sleep_ok); 5258} 5259 5260/** 5261 * t4_tp_get_tcp_stats - read TP's TCP MIB counters 5262 * @adap: the adapter 5263 * @v4: holds the TCP/IP counter values 5264 * @v6: holds the TCP/IPv6 counter values 5265 * @sleep_ok: if true we may sleep while awaiting command completion 5266 * 5267 * Returns the values of TP's TCP/IP and TCP/IPv6 MIB counters. 5268 * Either @v4 or @v6 may be %NULL to skip the corresponding stats. 5269 */ 5270void t4_tp_get_tcp_stats(struct adapter *adap, struct tp_tcp_stats *v4, 5271 struct tp_tcp_stats *v6, bool sleep_ok) 5272{ 5273 u32 val[A_TP_MIB_TCP_RXT_SEG_LO - A_TP_MIB_TCP_OUT_RST + 1]; 5274 5275#define STAT_IDX(x) ((A_TP_MIB_TCP_##x) - A_TP_MIB_TCP_OUT_RST) 5276#define STAT(x) val[STAT_IDX(x)] 5277#define STAT64(x) (((u64)STAT(x##_HI) << 32) | STAT(x##_LO)) 5278 5279 if (v4) { 5280 t4_tp_mib_read(adap, val, ARRAY_SIZE(val), 5281 A_TP_MIB_TCP_OUT_RST, sleep_ok); 5282 v4->tcp_out_rsts = STAT(OUT_RST); 5283 v4->tcp_in_segs = STAT64(IN_SEG); 5284 v4->tcp_out_segs = STAT64(OUT_SEG); 5285 v4->tcp_retrans_segs = STAT64(RXT_SEG); 5286 } 5287 if (v6) { 5288 t4_tp_mib_read(adap, val, ARRAY_SIZE(val), 5289 A_TP_MIB_TCP_V6OUT_RST, sleep_ok); 5290 v6->tcp_out_rsts = STAT(OUT_RST); 5291 v6->tcp_in_segs = STAT64(IN_SEG); 5292 v6->tcp_out_segs = STAT64(OUT_SEG); 5293 v6->tcp_retrans_segs = STAT64(RXT_SEG); 5294 } 5295#undef STAT64 5296#undef STAT 5297#undef STAT_IDX 5298} 5299 5300/** 5301 * t4_tp_get_err_stats - read TP's error MIB counters 5302 * @adap: the adapter 5303 * @st: holds the counter values 5304 * @sleep_ok: if true we may sleep while awaiting command completion 5305 * 5306 * Returns the values of TP's error counters. 5307 */ 5308void t4_tp_get_err_stats(struct adapter *adap, struct tp_err_stats *st, 5309 bool sleep_ok) 5310{ 5311 int nchan = adap->chip_params->nchan; 5312 5313 t4_tp_mib_read(adap, st->mac_in_errs, nchan, A_TP_MIB_MAC_IN_ERR_0, 5314 sleep_ok); 5315 5316 t4_tp_mib_read(adap, st->hdr_in_errs, nchan, A_TP_MIB_HDR_IN_ERR_0, 5317 sleep_ok); 5318 5319 t4_tp_mib_read(adap, st->tcp_in_errs, nchan, A_TP_MIB_TCP_IN_ERR_0, 5320 sleep_ok); 5321 5322 t4_tp_mib_read(adap, st->tnl_cong_drops, nchan, 5323 A_TP_MIB_TNL_CNG_DROP_0, sleep_ok); 5324 5325 t4_tp_mib_read(adap, st->ofld_chan_drops, nchan, 5326 A_TP_MIB_OFD_CHN_DROP_0, sleep_ok); 5327 5328 t4_tp_mib_read(adap, st->tnl_tx_drops, nchan, A_TP_MIB_TNL_DROP_0, 5329 sleep_ok); 5330 5331 t4_tp_mib_read(adap, st->ofld_vlan_drops, nchan, 5332 A_TP_MIB_OFD_VLN_DROP_0, sleep_ok); 5333 5334 t4_tp_mib_read(adap, st->tcp6_in_errs, nchan, 5335 A_TP_MIB_TCP_V6IN_ERR_0, sleep_ok); 5336 5337 t4_tp_mib_read(adap, &st->ofld_no_neigh, 2, A_TP_MIB_OFD_ARP_DROP, 5338 sleep_ok); 5339} 5340 5341/** 5342 * t4_tp_get_proxy_stats - read TP's proxy MIB counters 5343 * @adap: the adapter 5344 * @st: holds the counter values 5345 * 5346 * Returns the values of TP's proxy counters. 5347 */ 5348void t4_tp_get_proxy_stats(struct adapter *adap, struct tp_proxy_stats *st, 5349 bool sleep_ok) 5350{ 5351 int nchan = adap->chip_params->nchan; 5352 5353 t4_tp_mib_read(adap, st->proxy, nchan, A_TP_MIB_TNL_LPBK_0, sleep_ok); 5354} 5355 5356/** 5357 * t4_tp_get_cpl_stats - read TP's CPL MIB counters 5358 * @adap: the adapter 5359 * @st: holds the counter values 5360 * @sleep_ok: if true we may sleep while awaiting command completion 5361 * 5362 * Returns the values of TP's CPL counters. 5363 */ 5364void t4_tp_get_cpl_stats(struct adapter *adap, struct tp_cpl_stats *st, 5365 bool sleep_ok) 5366{ 5367 int nchan = adap->chip_params->nchan; 5368 5369 t4_tp_mib_read(adap, st->req, nchan, A_TP_MIB_CPL_IN_REQ_0, sleep_ok); 5370 5371 t4_tp_mib_read(adap, st->rsp, nchan, A_TP_MIB_CPL_OUT_RSP_0, sleep_ok); 5372} 5373 5374/** 5375 * t4_tp_get_rdma_stats - read TP's RDMA MIB counters 5376 * @adap: the adapter 5377 * @st: holds the counter values 5378 * 5379 * Returns the values of TP's RDMA counters. 5380 */ 5381void t4_tp_get_rdma_stats(struct adapter *adap, struct tp_rdma_stats *st, 5382 bool sleep_ok) 5383{ 5384 t4_tp_mib_read(adap, &st->rqe_dfr_pkt, 2, A_TP_MIB_RQE_DFR_PKT, 5385 sleep_ok); 5386} 5387 5388/** 5389 * t4_get_fcoe_stats - read TP's FCoE MIB counters for a port 5390 * @adap: the adapter 5391 * @idx: the port index 5392 * @st: holds the counter values 5393 * @sleep_ok: if true we may sleep while awaiting command completion 5394 * 5395 * Returns the values of TP's FCoE counters for the selected port. 5396 */ 5397void t4_get_fcoe_stats(struct adapter *adap, unsigned int idx, 5398 struct tp_fcoe_stats *st, bool sleep_ok) 5399{ 5400 u32 val[2]; 5401 5402 t4_tp_mib_read(adap, &st->frames_ddp, 1, A_TP_MIB_FCOE_DDP_0 + idx, 5403 sleep_ok); 5404 5405 t4_tp_mib_read(adap, &st->frames_drop, 1, 5406 A_TP_MIB_FCOE_DROP_0 + idx, sleep_ok); 5407 5408 t4_tp_mib_read(adap, val, 2, A_TP_MIB_FCOE_BYTE_0_HI + 2 * idx, 5409 sleep_ok); 5410 5411 st->octets_ddp = ((u64)val[0] << 32) | val[1]; 5412} 5413 5414/** 5415 * t4_get_usm_stats - read TP's non-TCP DDP MIB counters 5416 * @adap: the adapter 5417 * @st: holds the counter values 5418 * @sleep_ok: if true we may sleep while awaiting command completion 5419 * 5420 * Returns the values of TP's counters for non-TCP directly-placed packets. 5421 */ 5422void t4_get_usm_stats(struct adapter *adap, struct tp_usm_stats *st, 5423 bool sleep_ok) 5424{ 5425 u32 val[4]; 5426 5427 t4_tp_mib_read(adap, val, 4, A_TP_MIB_USM_PKTS, sleep_ok); 5428 5429 st->frames = val[0]; 5430 st->drops = val[1]; 5431 st->octets = ((u64)val[2] << 32) | val[3]; 5432} 5433 5434/** 5435 * t4_read_mtu_tbl - returns the values in the HW path MTU table 5436 * @adap: the adapter 5437 * @mtus: where to store the MTU values 5438 * @mtu_log: where to store the MTU base-2 log (may be %NULL) 5439 * 5440 * Reads the HW path MTU table. 5441 */ 5442void t4_read_mtu_tbl(struct adapter *adap, u16 *mtus, u8 *mtu_log) 5443{ 5444 u32 v; 5445 int i; 5446 5447 for (i = 0; i < NMTUS; ++i) { 5448 t4_write_reg(adap, A_TP_MTU_TABLE, 5449 V_MTUINDEX(0xff) | V_MTUVALUE(i)); 5450 v = t4_read_reg(adap, A_TP_MTU_TABLE); 5451 mtus[i] = G_MTUVALUE(v); 5452 if (mtu_log) 5453 mtu_log[i] = G_MTUWIDTH(v); 5454 } 5455} 5456 5457/** 5458 * t4_read_cong_tbl - reads the congestion control table 5459 * @adap: the adapter 5460 * @incr: where to store the alpha values 5461 * 5462 * Reads the additive increments programmed into the HW congestion 5463 * control table. 5464 */ 5465void t4_read_cong_tbl(struct adapter *adap, u16 incr[NMTUS][NCCTRL_WIN]) 5466{ 5467 unsigned int mtu, w; 5468 5469 for (mtu = 0; mtu < NMTUS; ++mtu) 5470 for (w = 0; w < NCCTRL_WIN; ++w) { 5471 t4_write_reg(adap, A_TP_CCTRL_TABLE, 5472 V_ROWINDEX(0xffff) | (mtu << 5) | w); 5473 incr[mtu][w] = (u16)t4_read_reg(adap, 5474 A_TP_CCTRL_TABLE) & 0x1fff; 5475 } 5476} 5477 5478/** 5479 * t4_tp_wr_bits_indirect - set/clear bits in an indirect TP register 5480 * @adap: the adapter 5481 * @addr: the indirect TP register address 5482 * @mask: specifies the field within the register to modify 5483 * @val: new value for the field 5484 * 5485 * Sets a field of an indirect TP register to the given value. 5486 */ 5487void t4_tp_wr_bits_indirect(struct adapter *adap, unsigned int addr, 5488 unsigned int mask, unsigned int val) 5489{ 5490 t4_write_reg(adap, A_TP_PIO_ADDR, addr); 5491 val |= t4_read_reg(adap, A_TP_PIO_DATA) & ~mask; 5492 t4_write_reg(adap, A_TP_PIO_DATA, val); 5493} 5494 5495/** 5496 * init_cong_ctrl - initialize congestion control parameters 5497 * @a: the alpha values for congestion control 5498 * @b: the beta values for congestion control 5499 * 5500 * Initialize the congestion control parameters. 5501 */ 5502static void init_cong_ctrl(unsigned short *a, unsigned short *b) 5503{ 5504 a[0] = a[1] = a[2] = a[3] = a[4] = a[5] = a[6] = a[7] = a[8] = 1; 5505 a[9] = 2; 5506 a[10] = 3; 5507 a[11] = 4; 5508 a[12] = 5; 5509 a[13] = 6; 5510 a[14] = 7; 5511 a[15] = 8; 5512 a[16] = 9; 5513 a[17] = 10; 5514 a[18] = 14; 5515 a[19] = 17; 5516 a[20] = 21; 5517 a[21] = 25; 5518 a[22] = 30; 5519 a[23] = 35; 5520 a[24] = 45; 5521 a[25] = 60; 5522 a[26] = 80; 5523 a[27] = 100; 5524 a[28] = 200; 5525 a[29] = 300; 5526 a[30] = 400; 5527 a[31] = 500; 5528 5529 b[0] = b[1] = b[2] = b[3] = b[4] = b[5] = b[6] = b[7] = b[8] = 0; 5530 b[9] = b[10] = 1; 5531 b[11] = b[12] = 2; 5532 b[13] = b[14] = b[15] = b[16] = 3; 5533 b[17] = b[18] = b[19] = b[20] = b[21] = 4; 5534 b[22] = b[23] = b[24] = b[25] = b[26] = b[27] = 5; 5535 b[28] = b[29] = 6; 5536 b[30] = b[31] = 7; 5537} 5538 5539/* The minimum additive increment value for the congestion control table */ 5540#define CC_MIN_INCR 2U 5541 5542/** 5543 * t4_load_mtus - write the MTU and congestion control HW tables 5544 * @adap: the adapter 5545 * @mtus: the values for the MTU table 5546 * @alpha: the values for the congestion control alpha parameter 5547 * @beta: the values for the congestion control beta parameter 5548 * 5549 * Write the HW MTU table with the supplied MTUs and the high-speed 5550 * congestion control table with the supplied alpha, beta, and MTUs. 5551 * We write the two tables together because the additive increments 5552 * depend on the MTUs. 5553 */ 5554void t4_load_mtus(struct adapter *adap, const unsigned short *mtus, 5555 const unsigned short *alpha, const unsigned short *beta) 5556{ 5557 static const unsigned int avg_pkts[NCCTRL_WIN] = { 5558 2, 6, 10, 14, 20, 28, 40, 56, 80, 112, 160, 224, 320, 448, 640, 5559 896, 1281, 1792, 2560, 3584, 5120, 7168, 10240, 14336, 20480, 5560 28672, 40960, 57344, 81920, 114688, 163840, 229376 5561 }; 5562 5563 unsigned int i, w; 5564 5565 for (i = 0; i < NMTUS; ++i) { 5566 unsigned int mtu = mtus[i]; 5567 unsigned int log2 = fls(mtu); 5568 5569 if (!(mtu & ((1 << log2) >> 2))) /* round */ 5570 log2--; 5571 t4_write_reg(adap, A_TP_MTU_TABLE, V_MTUINDEX(i) | 5572 V_MTUWIDTH(log2) | V_MTUVALUE(mtu)); 5573 5574 for (w = 0; w < NCCTRL_WIN; ++w) { 5575 unsigned int inc; 5576 5577 inc = max(((mtu - 40) * alpha[w]) / avg_pkts[w], 5578 CC_MIN_INCR); 5579 5580 t4_write_reg(adap, A_TP_CCTRL_TABLE, (i << 21) | 5581 (w << 16) | (beta[w] << 13) | inc); 5582 } 5583 } 5584} 5585 5586/** 5587 * t4_set_pace_tbl - set the pace table 5588 * @adap: the adapter 5589 * @pace_vals: the pace values in microseconds 5590 * @start: index of the first entry in the HW pace table to set 5591 * @n: how many entries to set 5592 * 5593 * Sets (a subset of the) HW pace table. 5594 */ 5595int t4_set_pace_tbl(struct adapter *adap, const unsigned int *pace_vals, 5596 unsigned int start, unsigned int n) 5597{ 5598 unsigned int vals[NTX_SCHED], i; 5599 unsigned int tick_ns = dack_ticks_to_usec(adap, 1000); 5600 5601 if (n > NTX_SCHED) 5602 return -ERANGE; 5603 5604 /* convert values from us to dack ticks, rounding to closest value */ 5605 for (i = 0; i < n; i++, pace_vals++) { 5606 vals[i] = (1000 * *pace_vals + tick_ns / 2) / tick_ns; 5607 if (vals[i] > 0x7ff) 5608 return -ERANGE; 5609 if (*pace_vals && vals[i] == 0) 5610 return -ERANGE; 5611 } 5612 for (i = 0; i < n; i++, start++) 5613 t4_write_reg(adap, A_TP_PACE_TABLE, (start << 16) | vals[i]); 5614 return 0; 5615} 5616 5617/** 5618 * t4_set_sched_bps - set the bit rate for a HW traffic scheduler 5619 * @adap: the adapter 5620 * @kbps: target rate in Kbps 5621 * @sched: the scheduler index 5622 * 5623 * Configure a Tx HW scheduler for the target rate. 5624 */ 5625int t4_set_sched_bps(struct adapter *adap, int sched, unsigned int kbps) 5626{ 5627 unsigned int v, tps, cpt, bpt, delta, mindelta = ~0; 5628 unsigned int clk = adap->params.vpd.cclk * 1000; 5629 unsigned int selected_cpt = 0, selected_bpt = 0; 5630 5631 if (kbps > 0) { 5632 kbps *= 125; /* -> bytes */ 5633 for (cpt = 1; cpt <= 255; cpt++) { 5634 tps = clk / cpt; 5635 bpt = (kbps + tps / 2) / tps; 5636 if (bpt > 0 && bpt <= 255) { 5637 v = bpt * tps; 5638 delta = v >= kbps ? v - kbps : kbps - v; 5639 if (delta < mindelta) { 5640 mindelta = delta; 5641 selected_cpt = cpt; 5642 selected_bpt = bpt; 5643 } 5644 } else if (selected_cpt) 5645 break; 5646 } 5647 if (!selected_cpt) 5648 return -EINVAL; 5649 } 5650 t4_write_reg(adap, A_TP_TM_PIO_ADDR, 5651 A_TP_TX_MOD_Q1_Q0_RATE_LIMIT - sched / 2); 5652 v = t4_read_reg(adap, A_TP_TM_PIO_DATA); 5653 if (sched & 1) 5654 v = (v & 0xffff) | (selected_cpt << 16) | (selected_bpt << 24); 5655 else 5656 v = (v & 0xffff0000) | selected_cpt | (selected_bpt << 8); 5657 t4_write_reg(adap, A_TP_TM_PIO_DATA, v); 5658 return 0; 5659} 5660 5661/** 5662 * t4_set_sched_ipg - set the IPG for a Tx HW packet rate scheduler 5663 * @adap: the adapter 5664 * @sched: the scheduler index 5665 * @ipg: the interpacket delay in tenths of nanoseconds 5666 * 5667 * Set the interpacket delay for a HW packet rate scheduler. 5668 */ 5669int t4_set_sched_ipg(struct adapter *adap, int sched, unsigned int ipg) 5670{ 5671 unsigned int v, addr = A_TP_TX_MOD_Q1_Q0_TIMER_SEPARATOR - sched / 2; 5672 5673 /* convert ipg to nearest number of core clocks */ 5674 ipg *= core_ticks_per_usec(adap); 5675 ipg = (ipg + 5000) / 10000; 5676 if (ipg > M_TXTIMERSEPQ0) 5677 return -EINVAL; 5678 5679 t4_write_reg(adap, A_TP_TM_PIO_ADDR, addr); 5680 v = t4_read_reg(adap, A_TP_TM_PIO_DATA); 5681 if (sched & 1) 5682 v = (v & V_TXTIMERSEPQ0(M_TXTIMERSEPQ0)) | V_TXTIMERSEPQ1(ipg); 5683 else 5684 v = (v & V_TXTIMERSEPQ1(M_TXTIMERSEPQ1)) | V_TXTIMERSEPQ0(ipg); 5685 t4_write_reg(adap, A_TP_TM_PIO_DATA, v); 5686 t4_read_reg(adap, A_TP_TM_PIO_DATA); 5687 return 0; 5688} 5689 5690/* 5691 * Calculates a rate in bytes/s given the number of 256-byte units per 4K core 5692 * clocks. The formula is 5693 * 5694 * bytes/s = bytes256 * 256 * ClkFreq / 4096 5695 * 5696 * which is equivalent to 5697 * 5698 * bytes/s = 62.5 * bytes256 * ClkFreq_ms 5699 */ 5700static u64 chan_rate(struct adapter *adap, unsigned int bytes256) 5701{ 5702 u64 v = bytes256 * adap->params.vpd.cclk; 5703 5704 return v * 62 + v / 2; 5705} 5706 5707/** 5708 * t4_get_chan_txrate - get the current per channel Tx rates 5709 * @adap: the adapter 5710 * @nic_rate: rates for NIC traffic 5711 * @ofld_rate: rates for offloaded traffic 5712 * 5713 * Return the current Tx rates in bytes/s for NIC and offloaded traffic 5714 * for each channel. 5715 */ 5716void t4_get_chan_txrate(struct adapter *adap, u64 *nic_rate, u64 *ofld_rate) 5717{ 5718 u32 v; 5719 5720 v = t4_read_reg(adap, A_TP_TX_TRATE); 5721 nic_rate[0] = chan_rate(adap, G_TNLRATE0(v)); 5722 nic_rate[1] = chan_rate(adap, G_TNLRATE1(v)); 5723 if (adap->chip_params->nchan > 2) { 5724 nic_rate[2] = chan_rate(adap, G_TNLRATE2(v)); 5725 nic_rate[3] = chan_rate(adap, G_TNLRATE3(v)); 5726 } 5727 5728 v = t4_read_reg(adap, A_TP_TX_ORATE); 5729 ofld_rate[0] = chan_rate(adap, G_OFDRATE0(v)); 5730 ofld_rate[1] = chan_rate(adap, G_OFDRATE1(v)); 5731 if (adap->chip_params->nchan > 2) { 5732 ofld_rate[2] = chan_rate(adap, G_OFDRATE2(v)); 5733 ofld_rate[3] = chan_rate(adap, G_OFDRATE3(v)); 5734 } 5735} 5736 5737/** 5738 * t4_set_trace_filter - configure one of the tracing filters 5739 * @adap: the adapter 5740 * @tp: the desired trace filter parameters 5741 * @idx: which filter to configure 5742 * @enable: whether to enable or disable the filter 5743 * 5744 * Configures one of the tracing filters available in HW. If @tp is %NULL 5745 * it indicates that the filter is already written in the register and it 5746 * just needs to be enabled or disabled. 5747 */ 5748int t4_set_trace_filter(struct adapter *adap, const struct trace_params *tp, 5749 int idx, int enable) 5750{ 5751 int i, ofst = idx * 4; 5752 u32 data_reg, mask_reg, cfg; 5753 u32 multitrc = F_TRCMULTIFILTER; 5754 u32 en = is_t4(adap) ? F_TFEN : F_T5_TFEN; 5755 5756 if (idx < 0 || idx >= NTRACE) 5757 return -EINVAL; 5758 5759 if (tp == NULL || !enable) { 5760 t4_set_reg_field(adap, A_MPS_TRC_FILTER_MATCH_CTL_A + ofst, en, 5761 enable ? en : 0); 5762 return 0; 5763 } 5764 5765 /* 5766 * TODO - After T4 data book is updated, specify the exact 5767 * section below. 5768 * 5769 * See T4 data book - MPS section for a complete description 5770 * of the below if..else handling of A_MPS_TRC_CFG register 5771 * value. 5772 */ 5773 cfg = t4_read_reg(adap, A_MPS_TRC_CFG); 5774 if (cfg & F_TRCMULTIFILTER) { 5775 /* 5776 * If multiple tracers are enabled, then maximum 5777 * capture size is 2.5KB (FIFO size of a single channel) 5778 * minus 2 flits for CPL_TRACE_PKT header. 5779 */ 5780 if (tp->snap_len > ((10 * 1024 / 4) - (2 * 8))) 5781 return -EINVAL; 5782 } else { 5783 /* 5784 * If multiple tracers are disabled, to avoid deadlocks 5785 * maximum packet capture size of 9600 bytes is recommended. 5786 * Also in this mode, only trace0 can be enabled and running. 5787 */ 5788 multitrc = 0; 5789 if (tp->snap_len > 9600 || idx) 5790 return -EINVAL; 5791 } 5792 5793 if (tp->port > (is_t4(adap) ? 11 : 19) || tp->invert > 1 || 5794 tp->skip_len > M_TFLENGTH || tp->skip_ofst > M_TFOFFSET || 5795 tp->min_len > M_TFMINPKTSIZE) 5796 return -EINVAL; 5797 5798 /* stop the tracer we'll be changing */ 5799 t4_set_reg_field(adap, A_MPS_TRC_FILTER_MATCH_CTL_A + ofst, en, 0); 5800 5801 idx *= (A_MPS_TRC_FILTER1_MATCH - A_MPS_TRC_FILTER0_MATCH); 5802 data_reg = A_MPS_TRC_FILTER0_MATCH + idx; 5803 mask_reg = A_MPS_TRC_FILTER0_DONT_CARE + idx; 5804 5805 for (i = 0; i < TRACE_LEN / 4; i++, data_reg += 4, mask_reg += 4) { 5806 t4_write_reg(adap, data_reg, tp->data[i]); 5807 t4_write_reg(adap, mask_reg, ~tp->mask[i]); 5808 } 5809 t4_write_reg(adap, A_MPS_TRC_FILTER_MATCH_CTL_B + ofst, 5810 V_TFCAPTUREMAX(tp->snap_len) | 5811 V_TFMINPKTSIZE(tp->min_len)); 5812 t4_write_reg(adap, A_MPS_TRC_FILTER_MATCH_CTL_A + ofst, 5813 V_TFOFFSET(tp->skip_ofst) | V_TFLENGTH(tp->skip_len) | en | 5814 (is_t4(adap) ? 5815 V_TFPORT(tp->port) | V_TFINVERTMATCH(tp->invert) : 5816 V_T5_TFPORT(tp->port) | V_T5_TFINVERTMATCH(tp->invert))); 5817 5818 return 0; 5819} 5820 5821/** 5822 * t4_get_trace_filter - query one of the tracing filters 5823 * @adap: the adapter 5824 * @tp: the current trace filter parameters 5825 * @idx: which trace filter to query 5826 * @enabled: non-zero if the filter is enabled 5827 * 5828 * Returns the current settings of one of the HW tracing filters. 5829 */ 5830void t4_get_trace_filter(struct adapter *adap, struct trace_params *tp, int idx, 5831 int *enabled) 5832{ 5833 u32 ctla, ctlb; 5834 int i, ofst = idx * 4; 5835 u32 data_reg, mask_reg; 5836 5837 ctla = t4_read_reg(adap, A_MPS_TRC_FILTER_MATCH_CTL_A + ofst); 5838 ctlb = t4_read_reg(adap, A_MPS_TRC_FILTER_MATCH_CTL_B + ofst); 5839 5840 if (is_t4(adap)) { 5841 *enabled = !!(ctla & F_TFEN); 5842 tp->port = G_TFPORT(ctla); 5843 tp->invert = !!(ctla & F_TFINVERTMATCH); 5844 } else { 5845 *enabled = !!(ctla & F_T5_TFEN); 5846 tp->port = G_T5_TFPORT(ctla); 5847 tp->invert = !!(ctla & F_T5_TFINVERTMATCH); 5848 } 5849 tp->snap_len = G_TFCAPTUREMAX(ctlb); 5850 tp->min_len = G_TFMINPKTSIZE(ctlb); 5851 tp->skip_ofst = G_TFOFFSET(ctla); 5852 tp->skip_len = G_TFLENGTH(ctla); 5853 5854 ofst = (A_MPS_TRC_FILTER1_MATCH - A_MPS_TRC_FILTER0_MATCH) * idx; 5855 data_reg = A_MPS_TRC_FILTER0_MATCH + ofst; 5856 mask_reg = A_MPS_TRC_FILTER0_DONT_CARE + ofst; 5857 5858 for (i = 0; i < TRACE_LEN / 4; i++, data_reg += 4, mask_reg += 4) { 5859 tp->mask[i] = ~t4_read_reg(adap, mask_reg); 5860 tp->data[i] = t4_read_reg(adap, data_reg) & tp->mask[i]; 5861 } 5862} 5863 5864/** 5865 * t4_pmtx_get_stats - returns the HW stats from PMTX 5866 * @adap: the adapter 5867 * @cnt: where to store the count statistics 5868 * @cycles: where to store the cycle statistics 5869 * 5870 * Returns performance statistics from PMTX. 5871 */ 5872void t4_pmtx_get_stats(struct adapter *adap, u32 cnt[], u64 cycles[]) 5873{ 5874 int i; 5875 u32 data[2]; 5876 5877 for (i = 0; i < adap->chip_params->pm_stats_cnt; i++) { 5878 t4_write_reg(adap, A_PM_TX_STAT_CONFIG, i + 1); 5879 cnt[i] = t4_read_reg(adap, A_PM_TX_STAT_COUNT); 5880 if (is_t4(adap)) 5881 cycles[i] = t4_read_reg64(adap, A_PM_TX_STAT_LSB); 5882 else { 5883 t4_read_indirect(adap, A_PM_TX_DBG_CTRL, 5884 A_PM_TX_DBG_DATA, data, 2, 5885 A_PM_TX_DBG_STAT_MSB); 5886 cycles[i] = (((u64)data[0] << 32) | data[1]); 5887 } 5888 } 5889} 5890 5891/** 5892 * t4_pmrx_get_stats - returns the HW stats from PMRX 5893 * @adap: the adapter 5894 * @cnt: where to store the count statistics 5895 * @cycles: where to store the cycle statistics 5896 * 5897 * Returns performance statistics from PMRX. 5898 */ 5899void t4_pmrx_get_stats(struct adapter *adap, u32 cnt[], u64 cycles[]) 5900{ 5901 int i; 5902 u32 data[2]; 5903 5904 for (i = 0; i < adap->chip_params->pm_stats_cnt; i++) { 5905 t4_write_reg(adap, A_PM_RX_STAT_CONFIG, i + 1); 5906 cnt[i] = t4_read_reg(adap, A_PM_RX_STAT_COUNT); 5907 if (is_t4(adap)) { 5908 cycles[i] = t4_read_reg64(adap, A_PM_RX_STAT_LSB); 5909 } else { 5910 t4_read_indirect(adap, A_PM_RX_DBG_CTRL, 5911 A_PM_RX_DBG_DATA, data, 2, 5912 A_PM_RX_DBG_STAT_MSB); 5913 cycles[i] = (((u64)data[0] << 32) | data[1]); 5914 } 5915 } 5916} 5917 5918/** 5919 * t4_get_mps_bg_map - return the buffer groups associated with a port 5920 * @adap: the adapter 5921 * @idx: the port index 5922 * 5923 * Returns a bitmap indicating which MPS buffer groups are associated 5924 * with the given port. Bit i is set if buffer group i is used by the 5925 * port. 5926 */ 5927static unsigned int t4_get_mps_bg_map(struct adapter *adap, int idx) 5928{ 5929 u32 n; 5930 5931 if (adap->params.mps_bg_map) 5932 return ((adap->params.mps_bg_map >> (idx << 3)) & 0xff); 5933 5934 n = G_NUMPORTS(t4_read_reg(adap, A_MPS_CMN_CTL)); 5935 if (n == 0) 5936 return idx == 0 ? 0xf : 0; 5937 if (n == 1 && chip_id(adap) <= CHELSIO_T5) 5938 return idx < 2 ? (3 << (2 * idx)) : 0; 5939 return 1 << idx; 5940} 5941 5942/* 5943 * TP RX e-channels associated with the port. 5944 */ 5945static unsigned int t4_get_rx_e_chan_map(struct adapter *adap, int idx) 5946{ 5947 u32 n = G_NUMPORTS(t4_read_reg(adap, A_MPS_CMN_CTL)); 5948 5949 if (n == 0) 5950 return idx == 0 ? 0xf : 0; 5951 if (n == 1 && chip_id(adap) <= CHELSIO_T5) 5952 return idx < 2 ? (3 << (2 * idx)) : 0; 5953 return 1 << idx; 5954} 5955 5956/** 5957 * t4_get_port_type_description - return Port Type string description 5958 * @port_type: firmware Port Type enumeration 5959 */ 5960const char *t4_get_port_type_description(enum fw_port_type port_type) 5961{ 5962 static const char *const port_type_description[] = { 5963 "Fiber_XFI", 5964 "Fiber_XAUI", 5965 "BT_SGMII", 5966 "BT_XFI", 5967 "BT_XAUI", 5968 "KX4", 5969 "CX4", 5970 "KX", 5971 "KR", 5972 "SFP", 5973 "BP_AP", 5974 "BP4_AP", 5975 "QSFP_10G", 5976 "QSA", 5977 "QSFP", 5978 "BP40_BA", 5979 "KR4_100G", 5980 "CR4_QSFP", 5981 "CR_QSFP", 5982 "CR2_QSFP", 5983 "SFP28", 5984 "KR_SFP28", 5985 }; 5986 5987 if (port_type < ARRAY_SIZE(port_type_description)) 5988 return port_type_description[port_type]; 5989 return "UNKNOWN"; 5990} 5991 5992/** 5993 * t4_get_port_stats_offset - collect port stats relative to a previous 5994 * snapshot 5995 * @adap: The adapter 5996 * @idx: The port 5997 * @stats: Current stats to fill 5998 * @offset: Previous stats snapshot 5999 */ 6000void t4_get_port_stats_offset(struct adapter *adap, int idx, 6001 struct port_stats *stats, 6002 struct port_stats *offset) 6003{ 6004 u64 *s, *o; 6005 int i; 6006 6007 t4_get_port_stats(adap, idx, stats); 6008 for (i = 0, s = (u64 *)stats, o = (u64 *)offset ; 6009 i < (sizeof(struct port_stats)/sizeof(u64)) ; 6010 i++, s++, o++) 6011 *s -= *o; 6012} 6013 6014/** 6015 * t4_get_port_stats - collect port statistics 6016 * @adap: the adapter 6017 * @idx: the port index 6018 * @p: the stats structure to fill 6019 * 6020 * Collect statistics related to the given port from HW. 6021 */ 6022void t4_get_port_stats(struct adapter *adap, int idx, struct port_stats *p) 6023{ 6024 u32 bgmap = adap2pinfo(adap, idx)->mps_bg_map; 6025 u32 stat_ctl = t4_read_reg(adap, A_MPS_STAT_CTL); 6026 6027#define GET_STAT(name) \ 6028 t4_read_reg64(adap, \ 6029 (is_t4(adap) ? PORT_REG(idx, A_MPS_PORT_STAT_##name##_L) : \ 6030 T5_PORT_REG(idx, A_MPS_PORT_STAT_##name##_L))) 6031#define GET_STAT_COM(name) t4_read_reg64(adap, A_MPS_STAT_##name##_L) 6032 6033 p->tx_pause = GET_STAT(TX_PORT_PAUSE); 6034 p->tx_octets = GET_STAT(TX_PORT_BYTES); 6035 p->tx_frames = GET_STAT(TX_PORT_FRAMES); 6036 p->tx_bcast_frames = GET_STAT(TX_PORT_BCAST); 6037 p->tx_mcast_frames = GET_STAT(TX_PORT_MCAST); 6038 p->tx_ucast_frames = GET_STAT(TX_PORT_UCAST); 6039 p->tx_error_frames = GET_STAT(TX_PORT_ERROR); 6040 p->tx_frames_64 = GET_STAT(TX_PORT_64B); 6041 p->tx_frames_65_127 = GET_STAT(TX_PORT_65B_127B); 6042 p->tx_frames_128_255 = GET_STAT(TX_PORT_128B_255B); 6043 p->tx_frames_256_511 = GET_STAT(TX_PORT_256B_511B); 6044 p->tx_frames_512_1023 = GET_STAT(TX_PORT_512B_1023B); 6045 p->tx_frames_1024_1518 = GET_STAT(TX_PORT_1024B_1518B); 6046 p->tx_frames_1519_max = GET_STAT(TX_PORT_1519B_MAX); 6047 p->tx_drop = GET_STAT(TX_PORT_DROP); 6048 p->tx_ppp0 = GET_STAT(TX_PORT_PPP0); 6049 p->tx_ppp1 = GET_STAT(TX_PORT_PPP1); 6050 p->tx_ppp2 = GET_STAT(TX_PORT_PPP2); 6051 p->tx_ppp3 = GET_STAT(TX_PORT_PPP3); 6052 p->tx_ppp4 = GET_STAT(TX_PORT_PPP4); 6053 p->tx_ppp5 = GET_STAT(TX_PORT_PPP5); 6054 p->tx_ppp6 = GET_STAT(TX_PORT_PPP6); 6055 p->tx_ppp7 = GET_STAT(TX_PORT_PPP7); 6056 6057 if (chip_id(adap) >= CHELSIO_T5) { 6058 if (stat_ctl & F_COUNTPAUSESTATTX) { 6059 p->tx_frames -= p->tx_pause; 6060 p->tx_octets -= p->tx_pause * 64; 6061 } 6062 if (stat_ctl & F_COUNTPAUSEMCTX) 6063 p->tx_mcast_frames -= p->tx_pause; 6064 } 6065 6066 p->rx_pause = GET_STAT(RX_PORT_PAUSE); 6067 p->rx_octets = GET_STAT(RX_PORT_BYTES); 6068 p->rx_frames = GET_STAT(RX_PORT_FRAMES); 6069 p->rx_bcast_frames = GET_STAT(RX_PORT_BCAST); 6070 p->rx_mcast_frames = GET_STAT(RX_PORT_MCAST); 6071 p->rx_ucast_frames = GET_STAT(RX_PORT_UCAST); 6072 p->rx_too_long = GET_STAT(RX_PORT_MTU_ERROR); 6073 p->rx_jabber = GET_STAT(RX_PORT_MTU_CRC_ERROR); 6074 p->rx_fcs_err = GET_STAT(RX_PORT_CRC_ERROR); 6075 p->rx_len_err = GET_STAT(RX_PORT_LEN_ERROR); 6076 p->rx_symbol_err = GET_STAT(RX_PORT_SYM_ERROR); 6077 p->rx_runt = GET_STAT(RX_PORT_LESS_64B); 6078 p->rx_frames_64 = GET_STAT(RX_PORT_64B); 6079 p->rx_frames_65_127 = GET_STAT(RX_PORT_65B_127B); 6080 p->rx_frames_128_255 = GET_STAT(RX_PORT_128B_255B); 6081 p->rx_frames_256_511 = GET_STAT(RX_PORT_256B_511B); 6082 p->rx_frames_512_1023 = GET_STAT(RX_PORT_512B_1023B); 6083 p->rx_frames_1024_1518 = GET_STAT(RX_PORT_1024B_1518B); 6084 p->rx_frames_1519_max = GET_STAT(RX_PORT_1519B_MAX); 6085 p->rx_ppp0 = GET_STAT(RX_PORT_PPP0); 6086 p->rx_ppp1 = GET_STAT(RX_PORT_PPP1); 6087 p->rx_ppp2 = GET_STAT(RX_PORT_PPP2); 6088 p->rx_ppp3 = GET_STAT(RX_PORT_PPP3); 6089 p->rx_ppp4 = GET_STAT(RX_PORT_PPP4); 6090 p->rx_ppp5 = GET_STAT(RX_PORT_PPP5); 6091 p->rx_ppp6 = GET_STAT(RX_PORT_PPP6); 6092 p->rx_ppp7 = GET_STAT(RX_PORT_PPP7); 6093 6094 if (chip_id(adap) >= CHELSIO_T5) { 6095 if (stat_ctl & F_COUNTPAUSESTATRX) { 6096 p->rx_frames -= p->rx_pause; 6097 p->rx_octets -= p->rx_pause * 64; 6098 } 6099 if (stat_ctl & F_COUNTPAUSEMCRX) 6100 p->rx_mcast_frames -= p->rx_pause; 6101 } 6102 6103 p->rx_ovflow0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_MAC_DROP_FRAME) : 0; 6104 p->rx_ovflow1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_MAC_DROP_FRAME) : 0; 6105 p->rx_ovflow2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_MAC_DROP_FRAME) : 0; 6106 p->rx_ovflow3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_MAC_DROP_FRAME) : 0; 6107 p->rx_trunc0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_MAC_TRUNC_FRAME) : 0; 6108 p->rx_trunc1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_MAC_TRUNC_FRAME) : 0; 6109 p->rx_trunc2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_MAC_TRUNC_FRAME) : 0; 6110 p->rx_trunc3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_MAC_TRUNC_FRAME) : 0; 6111 6112#undef GET_STAT 6113#undef GET_STAT_COM 6114} 6115 6116/** 6117 * t4_get_lb_stats - collect loopback port statistics 6118 * @adap: the adapter 6119 * @idx: the loopback port index 6120 * @p: the stats structure to fill 6121 * 6122 * Return HW statistics for the given loopback port. 6123 */ 6124void t4_get_lb_stats(struct adapter *adap, int idx, struct lb_port_stats *p) 6125{ 6126 u32 bgmap = adap2pinfo(adap, idx)->mps_bg_map; 6127 6128#define GET_STAT(name) \ 6129 t4_read_reg64(adap, \ 6130 (is_t4(adap) ? \ 6131 PORT_REG(idx, A_MPS_PORT_STAT_LB_PORT_##name##_L) : \ 6132 T5_PORT_REG(idx, A_MPS_PORT_STAT_LB_PORT_##name##_L))) 6133#define GET_STAT_COM(name) t4_read_reg64(adap, A_MPS_STAT_##name##_L) 6134 6135 p->octets = GET_STAT(BYTES); 6136 p->frames = GET_STAT(FRAMES); 6137 p->bcast_frames = GET_STAT(BCAST); 6138 p->mcast_frames = GET_STAT(MCAST); 6139 p->ucast_frames = GET_STAT(UCAST); 6140 p->error_frames = GET_STAT(ERROR); 6141 6142 p->frames_64 = GET_STAT(64B); 6143 p->frames_65_127 = GET_STAT(65B_127B); 6144 p->frames_128_255 = GET_STAT(128B_255B); 6145 p->frames_256_511 = GET_STAT(256B_511B); 6146 p->frames_512_1023 = GET_STAT(512B_1023B); 6147 p->frames_1024_1518 = GET_STAT(1024B_1518B); 6148 p->frames_1519_max = GET_STAT(1519B_MAX); 6149 p->drop = GET_STAT(DROP_FRAMES); 6150 6151 p->ovflow0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_LB_DROP_FRAME) : 0; 6152 p->ovflow1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_LB_DROP_FRAME) : 0; 6153 p->ovflow2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_LB_DROP_FRAME) : 0; 6154 p->ovflow3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_LB_DROP_FRAME) : 0; 6155 p->trunc0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_LB_TRUNC_FRAME) : 0; 6156 p->trunc1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_LB_TRUNC_FRAME) : 0; 6157 p->trunc2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_LB_TRUNC_FRAME) : 0; 6158 p->trunc3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_LB_TRUNC_FRAME) : 0; 6159 6160#undef GET_STAT 6161#undef GET_STAT_COM 6162} 6163 6164/** 6165 * t4_wol_magic_enable - enable/disable magic packet WoL 6166 * @adap: the adapter 6167 * @port: the physical port index 6168 * @addr: MAC address expected in magic packets, %NULL to disable 6169 * 6170 * Enables/disables magic packet wake-on-LAN for the selected port. 6171 */ 6172void t4_wol_magic_enable(struct adapter *adap, unsigned int port, 6173 const u8 *addr) 6174{ 6175 u32 mag_id_reg_l, mag_id_reg_h, port_cfg_reg; 6176 6177 if (is_t4(adap)) { 6178 mag_id_reg_l = PORT_REG(port, A_XGMAC_PORT_MAGIC_MACID_LO); 6179 mag_id_reg_h = PORT_REG(port, A_XGMAC_PORT_MAGIC_MACID_HI); 6180 port_cfg_reg = PORT_REG(port, A_XGMAC_PORT_CFG2); 6181 } else { 6182 mag_id_reg_l = T5_PORT_REG(port, A_MAC_PORT_MAGIC_MACID_LO); 6183 mag_id_reg_h = T5_PORT_REG(port, A_MAC_PORT_MAGIC_MACID_HI); 6184 port_cfg_reg = T5_PORT_REG(port, A_MAC_PORT_CFG2); 6185 } 6186 6187 if (addr) { 6188 t4_write_reg(adap, mag_id_reg_l, 6189 (addr[2] << 24) | (addr[3] << 16) | 6190 (addr[4] << 8) | addr[5]); 6191 t4_write_reg(adap, mag_id_reg_h, 6192 (addr[0] << 8) | addr[1]); 6193 } 6194 t4_set_reg_field(adap, port_cfg_reg, F_MAGICEN, 6195 V_MAGICEN(addr != NULL)); 6196} 6197 6198/** 6199 * t4_wol_pat_enable - enable/disable pattern-based WoL 6200 * @adap: the adapter 6201 * @port: the physical port index 6202 * @map: bitmap of which HW pattern filters to set 6203 * @mask0: byte mask for bytes 0-63 of a packet 6204 * @mask1: byte mask for bytes 64-127 of a packet 6205 * @crc: Ethernet CRC for selected bytes 6206 * @enable: enable/disable switch 6207 * 6208 * Sets the pattern filters indicated in @map to mask out the bytes 6209 * specified in @mask0/@mask1 in received packets and compare the CRC of 6210 * the resulting packet against @crc. If @enable is %true pattern-based 6211 * WoL is enabled, otherwise disabled. 6212 */ 6213int t4_wol_pat_enable(struct adapter *adap, unsigned int port, unsigned int map, 6214 u64 mask0, u64 mask1, unsigned int crc, bool enable) 6215{ 6216 int i; 6217 u32 port_cfg_reg; 6218 6219 if (is_t4(adap)) 6220 port_cfg_reg = PORT_REG(port, A_XGMAC_PORT_CFG2); 6221 else 6222 port_cfg_reg = T5_PORT_REG(port, A_MAC_PORT_CFG2); 6223 6224 if (!enable) { 6225 t4_set_reg_field(adap, port_cfg_reg, F_PATEN, 0); 6226 return 0; 6227 } 6228 if (map > 0xff) 6229 return -EINVAL; 6230 6231#define EPIO_REG(name) \ 6232 (is_t4(adap) ? PORT_REG(port, A_XGMAC_PORT_EPIO_##name) : \ 6233 T5_PORT_REG(port, A_MAC_PORT_EPIO_##name)) 6234 6235 t4_write_reg(adap, EPIO_REG(DATA1), mask0 >> 32); 6236 t4_write_reg(adap, EPIO_REG(DATA2), mask1); 6237 t4_write_reg(adap, EPIO_REG(DATA3), mask1 >> 32); 6238 6239 for (i = 0; i < NWOL_PAT; i++, map >>= 1) { 6240 if (!(map & 1)) 6241 continue; 6242 6243 /* write byte masks */ 6244 t4_write_reg(adap, EPIO_REG(DATA0), mask0); 6245 t4_write_reg(adap, EPIO_REG(OP), V_ADDRESS(i) | F_EPIOWR); 6246 t4_read_reg(adap, EPIO_REG(OP)); /* flush */ 6247 if (t4_read_reg(adap, EPIO_REG(OP)) & F_BUSY) 6248 return -ETIMEDOUT; 6249 6250 /* write CRC */ 6251 t4_write_reg(adap, EPIO_REG(DATA0), crc); 6252 t4_write_reg(adap, EPIO_REG(OP), V_ADDRESS(i + 32) | F_EPIOWR); 6253 t4_read_reg(adap, EPIO_REG(OP)); /* flush */ 6254 if (t4_read_reg(adap, EPIO_REG(OP)) & F_BUSY) 6255 return -ETIMEDOUT; 6256 } 6257#undef EPIO_REG 6258 6259 t4_set_reg_field(adap, port_cfg_reg, 0, F_PATEN); 6260 return 0; 6261} 6262 6263/* t4_mk_filtdelwr - create a delete filter WR 6264 * @ftid: the filter ID 6265 * @wr: the filter work request to populate 6266 * @qid: ingress queue to receive the delete notification 6267 * 6268 * Creates a filter work request to delete the supplied filter. If @qid is 6269 * negative the delete notification is suppressed. 6270 */ 6271void t4_mk_filtdelwr(unsigned int ftid, struct fw_filter_wr *wr, int qid) 6272{ 6273 memset(wr, 0, sizeof(*wr)); 6274 wr->op_pkd = cpu_to_be32(V_FW_WR_OP(FW_FILTER_WR)); 6275 wr->len16_pkd = cpu_to_be32(V_FW_WR_LEN16(sizeof(*wr) / 16)); 6276 wr->tid_to_iq = cpu_to_be32(V_FW_FILTER_WR_TID(ftid) | 6277 V_FW_FILTER_WR_NOREPLY(qid < 0)); 6278 wr->del_filter_to_l2tix = cpu_to_be32(F_FW_FILTER_WR_DEL_FILTER); 6279 if (qid >= 0) 6280 wr->rx_chan_rx_rpl_iq = 6281 cpu_to_be16(V_FW_FILTER_WR_RX_RPL_IQ(qid)); 6282} 6283 6284#define INIT_CMD(var, cmd, rd_wr) do { \ 6285 (var).op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_##cmd##_CMD) | \ 6286 F_FW_CMD_REQUEST | \ 6287 F_FW_CMD_##rd_wr); \ 6288 (var).retval_len16 = cpu_to_be32(FW_LEN16(var)); \ 6289} while (0) 6290 6291int t4_fwaddrspace_write(struct adapter *adap, unsigned int mbox, 6292 u32 addr, u32 val) 6293{ 6294 u32 ldst_addrspace; 6295 struct fw_ldst_cmd c; 6296 6297 memset(&c, 0, sizeof(c)); 6298 ldst_addrspace = V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_FIRMWARE); 6299 c.op_to_addrspace = cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 6300 F_FW_CMD_REQUEST | 6301 F_FW_CMD_WRITE | 6302 ldst_addrspace); 6303 c.cycles_to_len16 = cpu_to_be32(FW_LEN16(c)); 6304 c.u.addrval.addr = cpu_to_be32(addr); 6305 c.u.addrval.val = cpu_to_be32(val); 6306 6307 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 6308} 6309 6310/** 6311 * t4_mdio_rd - read a PHY register through MDIO 6312 * @adap: the adapter 6313 * @mbox: mailbox to use for the FW command 6314 * @phy_addr: the PHY address 6315 * @mmd: the PHY MMD to access (0 for clause 22 PHYs) 6316 * @reg: the register to read 6317 * @valp: where to store the value 6318 * 6319 * Issues a FW command through the given mailbox to read a PHY register. 6320 */ 6321int t4_mdio_rd(struct adapter *adap, unsigned int mbox, unsigned int phy_addr, 6322 unsigned int mmd, unsigned int reg, unsigned int *valp) 6323{ 6324 int ret; 6325 u32 ldst_addrspace; 6326 struct fw_ldst_cmd c; 6327 6328 memset(&c, 0, sizeof(c)); 6329 ldst_addrspace = V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_MDIO); 6330 c.op_to_addrspace = cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 6331 F_FW_CMD_REQUEST | F_FW_CMD_READ | 6332 ldst_addrspace); 6333 c.cycles_to_len16 = cpu_to_be32(FW_LEN16(c)); 6334 c.u.mdio.paddr_mmd = cpu_to_be16(V_FW_LDST_CMD_PADDR(phy_addr) | 6335 V_FW_LDST_CMD_MMD(mmd)); 6336 c.u.mdio.raddr = cpu_to_be16(reg); 6337 6338 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 6339 if (ret == 0) 6340 *valp = be16_to_cpu(c.u.mdio.rval); 6341 return ret; 6342} 6343 6344/** 6345 * t4_mdio_wr - write a PHY register through MDIO 6346 * @adap: the adapter 6347 * @mbox: mailbox to use for the FW command 6348 * @phy_addr: the PHY address 6349 * @mmd: the PHY MMD to access (0 for clause 22 PHYs) 6350 * @reg: the register to write 6351 * @valp: value to write 6352 * 6353 * Issues a FW command through the given mailbox to write a PHY register. 6354 */ 6355int t4_mdio_wr(struct adapter *adap, unsigned int mbox, unsigned int phy_addr, 6356 unsigned int mmd, unsigned int reg, unsigned int val) 6357{ 6358 u32 ldst_addrspace; 6359 struct fw_ldst_cmd c; 6360 6361 memset(&c, 0, sizeof(c)); 6362 ldst_addrspace = V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_MDIO); 6363 c.op_to_addrspace = cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 6364 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 6365 ldst_addrspace); 6366 c.cycles_to_len16 = cpu_to_be32(FW_LEN16(c)); 6367 c.u.mdio.paddr_mmd = cpu_to_be16(V_FW_LDST_CMD_PADDR(phy_addr) | 6368 V_FW_LDST_CMD_MMD(mmd)); 6369 c.u.mdio.raddr = cpu_to_be16(reg); 6370 c.u.mdio.rval = cpu_to_be16(val); 6371 6372 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 6373} 6374 6375/** 6376 * 6377 * t4_sge_decode_idma_state - decode the idma state 6378 * @adap: the adapter 6379 * @state: the state idma is stuck in 6380 */ 6381void t4_sge_decode_idma_state(struct adapter *adapter, int state) 6382{ 6383 static const char * const t4_decode[] = { 6384 "IDMA_IDLE", 6385 "IDMA_PUSH_MORE_CPL_FIFO", 6386 "IDMA_PUSH_CPL_MSG_HEADER_TO_FIFO", 6387 "Not used", 6388 "IDMA_PHYSADDR_SEND_PCIEHDR", 6389 "IDMA_PHYSADDR_SEND_PAYLOAD_FIRST", 6390 "IDMA_PHYSADDR_SEND_PAYLOAD", 6391 "IDMA_SEND_FIFO_TO_IMSG", 6392 "IDMA_FL_REQ_DATA_FL_PREP", 6393 "IDMA_FL_REQ_DATA_FL", 6394 "IDMA_FL_DROP", 6395 "IDMA_FL_H_REQ_HEADER_FL", 6396 "IDMA_FL_H_SEND_PCIEHDR", 6397 "IDMA_FL_H_PUSH_CPL_FIFO", 6398 "IDMA_FL_H_SEND_CPL", 6399 "IDMA_FL_H_SEND_IP_HDR_FIRST", 6400 "IDMA_FL_H_SEND_IP_HDR", 6401 "IDMA_FL_H_REQ_NEXT_HEADER_FL", 6402 "IDMA_FL_H_SEND_NEXT_PCIEHDR", 6403 "IDMA_FL_H_SEND_IP_HDR_PADDING", 6404 "IDMA_FL_D_SEND_PCIEHDR", 6405 "IDMA_FL_D_SEND_CPL_AND_IP_HDR", 6406 "IDMA_FL_D_REQ_NEXT_DATA_FL", 6407 "IDMA_FL_SEND_PCIEHDR", 6408 "IDMA_FL_PUSH_CPL_FIFO", 6409 "IDMA_FL_SEND_CPL", 6410 "IDMA_FL_SEND_PAYLOAD_FIRST", 6411 "IDMA_FL_SEND_PAYLOAD", 6412 "IDMA_FL_REQ_NEXT_DATA_FL", 6413 "IDMA_FL_SEND_NEXT_PCIEHDR", 6414 "IDMA_FL_SEND_PADDING", 6415 "IDMA_FL_SEND_COMPLETION_TO_IMSG", 6416 "IDMA_FL_SEND_FIFO_TO_IMSG", 6417 "IDMA_FL_REQ_DATAFL_DONE", 6418 "IDMA_FL_REQ_HEADERFL_DONE", 6419 }; 6420 static const char * const t5_decode[] = { 6421 "IDMA_IDLE", 6422 "IDMA_ALMOST_IDLE", 6423 "IDMA_PUSH_MORE_CPL_FIFO", 6424 "IDMA_PUSH_CPL_MSG_HEADER_TO_FIFO", 6425 "IDMA_SGEFLRFLUSH_SEND_PCIEHDR", 6426 "IDMA_PHYSADDR_SEND_PCIEHDR", 6427 "IDMA_PHYSADDR_SEND_PAYLOAD_FIRST", 6428 "IDMA_PHYSADDR_SEND_PAYLOAD", 6429 "IDMA_SEND_FIFO_TO_IMSG", 6430 "IDMA_FL_REQ_DATA_FL", 6431 "IDMA_FL_DROP", 6432 "IDMA_FL_DROP_SEND_INC", 6433 "IDMA_FL_H_REQ_HEADER_FL", 6434 "IDMA_FL_H_SEND_PCIEHDR", 6435 "IDMA_FL_H_PUSH_CPL_FIFO", 6436 "IDMA_FL_H_SEND_CPL", 6437 "IDMA_FL_H_SEND_IP_HDR_FIRST", 6438 "IDMA_FL_H_SEND_IP_HDR", 6439 "IDMA_FL_H_REQ_NEXT_HEADER_FL", 6440 "IDMA_FL_H_SEND_NEXT_PCIEHDR", 6441 "IDMA_FL_H_SEND_IP_HDR_PADDING", 6442 "IDMA_FL_D_SEND_PCIEHDR", 6443 "IDMA_FL_D_SEND_CPL_AND_IP_HDR", 6444 "IDMA_FL_D_REQ_NEXT_DATA_FL", 6445 "IDMA_FL_SEND_PCIEHDR", 6446 "IDMA_FL_PUSH_CPL_FIFO", 6447 "IDMA_FL_SEND_CPL", 6448 "IDMA_FL_SEND_PAYLOAD_FIRST", 6449 "IDMA_FL_SEND_PAYLOAD", 6450 "IDMA_FL_REQ_NEXT_DATA_FL", 6451 "IDMA_FL_SEND_NEXT_PCIEHDR", 6452 "IDMA_FL_SEND_PADDING", 6453 "IDMA_FL_SEND_COMPLETION_TO_IMSG", 6454 }; 6455 static const char * const t6_decode[] = { 6456 "IDMA_IDLE", 6457 "IDMA_PUSH_MORE_CPL_FIFO", 6458 "IDMA_PUSH_CPL_MSG_HEADER_TO_FIFO", 6459 "IDMA_SGEFLRFLUSH_SEND_PCIEHDR", 6460 "IDMA_PHYSADDR_SEND_PCIEHDR", 6461 "IDMA_PHYSADDR_SEND_PAYLOAD_FIRST", 6462 "IDMA_PHYSADDR_SEND_PAYLOAD", 6463 "IDMA_FL_REQ_DATA_FL", 6464 "IDMA_FL_DROP", 6465 "IDMA_FL_DROP_SEND_INC", 6466 "IDMA_FL_H_REQ_HEADER_FL", 6467 "IDMA_FL_H_SEND_PCIEHDR", 6468 "IDMA_FL_H_PUSH_CPL_FIFO", 6469 "IDMA_FL_H_SEND_CPL", 6470 "IDMA_FL_H_SEND_IP_HDR_FIRST", 6471 "IDMA_FL_H_SEND_IP_HDR", 6472 "IDMA_FL_H_REQ_NEXT_HEADER_FL", 6473 "IDMA_FL_H_SEND_NEXT_PCIEHDR", 6474 "IDMA_FL_H_SEND_IP_HDR_PADDING", 6475 "IDMA_FL_D_SEND_PCIEHDR", 6476 "IDMA_FL_D_SEND_CPL_AND_IP_HDR", 6477 "IDMA_FL_D_REQ_NEXT_DATA_FL", 6478 "IDMA_FL_SEND_PCIEHDR", 6479 "IDMA_FL_PUSH_CPL_FIFO", 6480 "IDMA_FL_SEND_CPL", 6481 "IDMA_FL_SEND_PAYLOAD_FIRST", 6482 "IDMA_FL_SEND_PAYLOAD", 6483 "IDMA_FL_REQ_NEXT_DATA_FL", 6484 "IDMA_FL_SEND_NEXT_PCIEHDR", 6485 "IDMA_FL_SEND_PADDING", 6486 "IDMA_FL_SEND_COMPLETION_TO_IMSG", 6487 }; 6488 static const u32 sge_regs[] = { 6489 A_SGE_DEBUG_DATA_LOW_INDEX_2, 6490 A_SGE_DEBUG_DATA_LOW_INDEX_3, 6491 A_SGE_DEBUG_DATA_HIGH_INDEX_10, 6492 }; 6493 const char * const *sge_idma_decode; 6494 int sge_idma_decode_nstates; 6495 int i; 6496 unsigned int chip_version = chip_id(adapter); 6497 6498 /* Select the right set of decode strings to dump depending on the 6499 * adapter chip type. 6500 */ 6501 switch (chip_version) { 6502 case CHELSIO_T4: 6503 sge_idma_decode = (const char * const *)t4_decode; 6504 sge_idma_decode_nstates = ARRAY_SIZE(t4_decode); 6505 break; 6506 6507 case CHELSIO_T5: 6508 sge_idma_decode = (const char * const *)t5_decode; 6509 sge_idma_decode_nstates = ARRAY_SIZE(t5_decode); 6510 break; 6511 6512 case CHELSIO_T6: 6513 sge_idma_decode = (const char * const *)t6_decode; 6514 sge_idma_decode_nstates = ARRAY_SIZE(t6_decode); 6515 break; 6516 6517 default: 6518 CH_ERR(adapter, "Unsupported chip version %d\n", chip_version); 6519 return; 6520 } 6521 6522 if (state < sge_idma_decode_nstates) 6523 CH_WARN(adapter, "idma state %s\n", sge_idma_decode[state]); 6524 else 6525 CH_WARN(adapter, "idma state %d unknown\n", state); 6526 6527 for (i = 0; i < ARRAY_SIZE(sge_regs); i++) 6528 CH_WARN(adapter, "SGE register %#x value %#x\n", 6529 sge_regs[i], t4_read_reg(adapter, sge_regs[i])); 6530} 6531 6532/** 6533 * t4_sge_ctxt_flush - flush the SGE context cache 6534 * @adap: the adapter 6535 * @mbox: mailbox to use for the FW command 6536 * 6537 * Issues a FW command through the given mailbox to flush the 6538 * SGE context cache. 6539 */ 6540int t4_sge_ctxt_flush(struct adapter *adap, unsigned int mbox) 6541{ 6542 int ret; 6543 u32 ldst_addrspace; 6544 struct fw_ldst_cmd c; 6545 6546 memset(&c, 0, sizeof(c)); 6547 ldst_addrspace = V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_SGE_EGRC); 6548 c.op_to_addrspace = cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 6549 F_FW_CMD_REQUEST | F_FW_CMD_READ | 6550 ldst_addrspace); 6551 c.cycles_to_len16 = cpu_to_be32(FW_LEN16(c)); 6552 c.u.idctxt.msg_ctxtflush = cpu_to_be32(F_FW_LDST_CMD_CTXTFLUSH); 6553 6554 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 6555 return ret; 6556} 6557 6558/** 6559 * t4_fw_hello - establish communication with FW 6560 * @adap: the adapter 6561 * @mbox: mailbox to use for the FW command 6562 * @evt_mbox: mailbox to receive async FW events 6563 * @master: specifies the caller's willingness to be the device master 6564 * @state: returns the current device state (if non-NULL) 6565 * 6566 * Issues a command to establish communication with FW. Returns either 6567 * an error (negative integer) or the mailbox of the Master PF. 6568 */ 6569int t4_fw_hello(struct adapter *adap, unsigned int mbox, unsigned int evt_mbox, 6570 enum dev_master master, enum dev_state *state) 6571{ 6572 int ret; 6573 struct fw_hello_cmd c; 6574 u32 v; 6575 unsigned int master_mbox; 6576 int retries = FW_CMD_HELLO_RETRIES; 6577 6578retry: 6579 memset(&c, 0, sizeof(c)); 6580 INIT_CMD(c, HELLO, WRITE); 6581 c.err_to_clearinit = cpu_to_be32( 6582 V_FW_HELLO_CMD_MASTERDIS(master == MASTER_CANT) | 6583 V_FW_HELLO_CMD_MASTERFORCE(master == MASTER_MUST) | 6584 V_FW_HELLO_CMD_MBMASTER(master == MASTER_MUST ? 6585 mbox : M_FW_HELLO_CMD_MBMASTER) | 6586 V_FW_HELLO_CMD_MBASYNCNOT(evt_mbox) | 6587 V_FW_HELLO_CMD_STAGE(FW_HELLO_CMD_STAGE_OS) | 6588 F_FW_HELLO_CMD_CLEARINIT); 6589 6590 /* 6591 * Issue the HELLO command to the firmware. If it's not successful 6592 * but indicates that we got a "busy" or "timeout" condition, retry 6593 * the HELLO until we exhaust our retry limit. If we do exceed our 6594 * retry limit, check to see if the firmware left us any error 6595 * information and report that if so ... 6596 */ 6597 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 6598 if (ret != FW_SUCCESS) { 6599 if ((ret == -EBUSY || ret == -ETIMEDOUT) && retries-- > 0) 6600 goto retry; 6601 if (t4_read_reg(adap, A_PCIE_FW) & F_PCIE_FW_ERR) 6602 t4_report_fw_error(adap); 6603 return ret; 6604 } 6605 6606 v = be32_to_cpu(c.err_to_clearinit); 6607 master_mbox = G_FW_HELLO_CMD_MBMASTER(v); 6608 if (state) { 6609 if (v & F_FW_HELLO_CMD_ERR) 6610 *state = DEV_STATE_ERR; 6611 else if (v & F_FW_HELLO_CMD_INIT) 6612 *state = DEV_STATE_INIT; 6613 else 6614 *state = DEV_STATE_UNINIT; 6615 } 6616 6617 /* 6618 * If we're not the Master PF then we need to wait around for the 6619 * Master PF Driver to finish setting up the adapter. 6620 * 6621 * Note that we also do this wait if we're a non-Master-capable PF and 6622 * there is no current Master PF; a Master PF may show up momentarily 6623 * and we wouldn't want to fail pointlessly. (This can happen when an 6624 * OS loads lots of different drivers rapidly at the same time). In 6625 * this case, the Master PF returned by the firmware will be 6626 * M_PCIE_FW_MASTER so the test below will work ... 6627 */ 6628 if ((v & (F_FW_HELLO_CMD_ERR|F_FW_HELLO_CMD_INIT)) == 0 && 6629 master_mbox != mbox) { 6630 int waiting = FW_CMD_HELLO_TIMEOUT; 6631 6632 /* 6633 * Wait for the firmware to either indicate an error or 6634 * initialized state. If we see either of these we bail out 6635 * and report the issue to the caller. If we exhaust the 6636 * "hello timeout" and we haven't exhausted our retries, try 6637 * again. Otherwise bail with a timeout error. 6638 */ 6639 for (;;) { 6640 u32 pcie_fw; 6641 6642 msleep(50); 6643 waiting -= 50; 6644 6645 /* 6646 * If neither Error nor Initialialized are indicated 6647 * by the firmware keep waiting till we exhaust our 6648 * timeout ... and then retry if we haven't exhausted 6649 * our retries ... 6650 */ 6651 pcie_fw = t4_read_reg(adap, A_PCIE_FW); 6652 if (!(pcie_fw & (F_PCIE_FW_ERR|F_PCIE_FW_INIT))) { 6653 if (waiting <= 0) { 6654 if (retries-- > 0) 6655 goto retry; 6656 6657 return -ETIMEDOUT; 6658 } 6659 continue; 6660 } 6661 6662 /* 6663 * We either have an Error or Initialized condition 6664 * report errors preferentially. 6665 */ 6666 if (state) { 6667 if (pcie_fw & F_PCIE_FW_ERR) 6668 *state = DEV_STATE_ERR; 6669 else if (pcie_fw & F_PCIE_FW_INIT) 6670 *state = DEV_STATE_INIT; 6671 } 6672 6673 /* 6674 * If we arrived before a Master PF was selected and 6675 * there's not a valid Master PF, grab its identity 6676 * for our caller. 6677 */ 6678 if (master_mbox == M_PCIE_FW_MASTER && 6679 (pcie_fw & F_PCIE_FW_MASTER_VLD)) 6680 master_mbox = G_PCIE_FW_MASTER(pcie_fw); 6681 break; 6682 } 6683 } 6684 6685 return master_mbox; 6686} 6687 6688/** 6689 * t4_fw_bye - end communication with FW 6690 * @adap: the adapter 6691 * @mbox: mailbox to use for the FW command 6692 * 6693 * Issues a command to terminate communication with FW. 6694 */ 6695int t4_fw_bye(struct adapter *adap, unsigned int mbox) 6696{ 6697 struct fw_bye_cmd c; 6698 6699 memset(&c, 0, sizeof(c)); 6700 INIT_CMD(c, BYE, WRITE); 6701 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 6702} 6703 6704/** 6705 * t4_fw_reset - issue a reset to FW 6706 * @adap: the adapter 6707 * @mbox: mailbox to use for the FW command 6708 * @reset: specifies the type of reset to perform 6709 * 6710 * Issues a reset command of the specified type to FW. 6711 */ 6712int t4_fw_reset(struct adapter *adap, unsigned int mbox, int reset) 6713{ 6714 struct fw_reset_cmd c; 6715 6716 memset(&c, 0, sizeof(c)); 6717 INIT_CMD(c, RESET, WRITE); 6718 c.val = cpu_to_be32(reset); 6719 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 6720} 6721 6722/** 6723 * t4_fw_halt - issue a reset/halt to FW and put uP into RESET 6724 * @adap: the adapter 6725 * @mbox: mailbox to use for the FW RESET command (if desired) 6726 * @force: force uP into RESET even if FW RESET command fails 6727 * 6728 * Issues a RESET command to firmware (if desired) with a HALT indication 6729 * and then puts the microprocessor into RESET state. The RESET command 6730 * will only be issued if a legitimate mailbox is provided (mbox <= 6731 * M_PCIE_FW_MASTER). 6732 * 6733 * This is generally used in order for the host to safely manipulate the 6734 * adapter without fear of conflicting with whatever the firmware might 6735 * be doing. The only way out of this state is to RESTART the firmware 6736 * ... 6737 */ 6738int t4_fw_halt(struct adapter *adap, unsigned int mbox, int force) 6739{ 6740 int ret = 0; 6741 6742 /* 6743 * If a legitimate mailbox is provided, issue a RESET command 6744 * with a HALT indication. 6745 */ 6746 if (mbox <= M_PCIE_FW_MASTER) { 6747 struct fw_reset_cmd c; 6748 6749 memset(&c, 0, sizeof(c)); 6750 INIT_CMD(c, RESET, WRITE); 6751 c.val = cpu_to_be32(F_PIORST | F_PIORSTMODE); 6752 c.halt_pkd = cpu_to_be32(F_FW_RESET_CMD_HALT); 6753 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 6754 } 6755 6756 /* 6757 * Normally we won't complete the operation if the firmware RESET 6758 * command fails but if our caller insists we'll go ahead and put the 6759 * uP into RESET. This can be useful if the firmware is hung or even 6760 * missing ... We'll have to take the risk of putting the uP into 6761 * RESET without the cooperation of firmware in that case. 6762 * 6763 * We also force the firmware's HALT flag to be on in case we bypassed 6764 * the firmware RESET command above or we're dealing with old firmware 6765 * which doesn't have the HALT capability. This will serve as a flag 6766 * for the incoming firmware to know that it's coming out of a HALT 6767 * rather than a RESET ... if it's new enough to understand that ... 6768 */ 6769 if (ret == 0 || force) { 6770 t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, F_UPCRST); 6771 t4_set_reg_field(adap, A_PCIE_FW, F_PCIE_FW_HALT, 6772 F_PCIE_FW_HALT); 6773 } 6774 6775 /* 6776 * And we always return the result of the firmware RESET command 6777 * even when we force the uP into RESET ... 6778 */ 6779 return ret; 6780} 6781 6782/** 6783 * t4_fw_restart - restart the firmware by taking the uP out of RESET 6784 * @adap: the adapter 6785 * @reset: if we want to do a RESET to restart things 6786 * 6787 * Restart firmware previously halted by t4_fw_halt(). On successful 6788 * return the previous PF Master remains as the new PF Master and there 6789 * is no need to issue a new HELLO command, etc. 6790 * 6791 * We do this in two ways: 6792 * 6793 * 1. If we're dealing with newer firmware we'll simply want to take 6794 * the chip's microprocessor out of RESET. This will cause the 6795 * firmware to start up from its start vector. And then we'll loop 6796 * until the firmware indicates it's started again (PCIE_FW.HALT 6797 * reset to 0) or we timeout. 6798 * 6799 * 2. If we're dealing with older firmware then we'll need to RESET 6800 * the chip since older firmware won't recognize the PCIE_FW.HALT 6801 * flag and automatically RESET itself on startup. 6802 */ 6803int t4_fw_restart(struct adapter *adap, unsigned int mbox, int reset) 6804{ 6805 if (reset) { 6806 /* 6807 * Since we're directing the RESET instead of the firmware 6808 * doing it automatically, we need to clear the PCIE_FW.HALT 6809 * bit. 6810 */ 6811 t4_set_reg_field(adap, A_PCIE_FW, F_PCIE_FW_HALT, 0); 6812 6813 /* 6814 * If we've been given a valid mailbox, first try to get the 6815 * firmware to do the RESET. If that works, great and we can 6816 * return success. Otherwise, if we haven't been given a 6817 * valid mailbox or the RESET command failed, fall back to 6818 * hitting the chip with a hammer. 6819 */ 6820 if (mbox <= M_PCIE_FW_MASTER) { 6821 t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, 0); 6822 msleep(100); 6823 if (t4_fw_reset(adap, mbox, 6824 F_PIORST | F_PIORSTMODE) == 0) 6825 return 0; 6826 } 6827 6828 t4_write_reg(adap, A_PL_RST, F_PIORST | F_PIORSTMODE); 6829 msleep(2000); 6830 } else { 6831 int ms; 6832 6833 t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, 0); 6834 for (ms = 0; ms < FW_CMD_MAX_TIMEOUT; ) { 6835 if (!(t4_read_reg(adap, A_PCIE_FW) & F_PCIE_FW_HALT)) 6836 return FW_SUCCESS; 6837 msleep(100); 6838 ms += 100; 6839 } 6840 return -ETIMEDOUT; 6841 } 6842 return 0; 6843} 6844 6845/** 6846 * t4_fw_upgrade - perform all of the steps necessary to upgrade FW 6847 * @adap: the adapter 6848 * @mbox: mailbox to use for the FW RESET command (if desired) 6849 * @fw_data: the firmware image to write 6850 * @size: image size 6851 * @force: force upgrade even if firmware doesn't cooperate 6852 * 6853 * Perform all of the steps necessary for upgrading an adapter's 6854 * firmware image. Normally this requires the cooperation of the 6855 * existing firmware in order to halt all existing activities 6856 * but if an invalid mailbox token is passed in we skip that step 6857 * (though we'll still put the adapter microprocessor into RESET in 6858 * that case). 6859 * 6860 * On successful return the new firmware will have been loaded and 6861 * the adapter will have been fully RESET losing all previous setup 6862 * state. On unsuccessful return the adapter may be completely hosed ... 6863 * positive errno indicates that the adapter is ~probably~ intact, a 6864 * negative errno indicates that things are looking bad ... 6865 */ 6866int t4_fw_upgrade(struct adapter *adap, unsigned int mbox, 6867 const u8 *fw_data, unsigned int size, int force) 6868{ 6869 const struct fw_hdr *fw_hdr = (const struct fw_hdr *)fw_data; 6870 unsigned int bootstrap = 6871 be32_to_cpu(fw_hdr->magic) == FW_HDR_MAGIC_BOOTSTRAP; 6872 int reset, ret; 6873 6874 if (!t4_fw_matches_chip(adap, fw_hdr)) 6875 return -EINVAL; 6876 6877 if (!bootstrap) { 6878 ret = t4_fw_halt(adap, mbox, force); 6879 if (ret < 0 && !force) 6880 return ret; 6881 } 6882 6883 ret = t4_load_fw(adap, fw_data, size); 6884 if (ret < 0 || bootstrap) 6885 return ret; 6886 6887 /* 6888 * Older versions of the firmware don't understand the new 6889 * PCIE_FW.HALT flag and so won't know to perform a RESET when they 6890 * restart. So for newly loaded older firmware we'll have to do the 6891 * RESET for it so it starts up on a clean slate. We can tell if 6892 * the newly loaded firmware will handle this right by checking 6893 * its header flags to see if it advertises the capability. 6894 */ 6895 reset = ((be32_to_cpu(fw_hdr->flags) & FW_HDR_FLAGS_RESET_HALT) == 0); 6896 return t4_fw_restart(adap, mbox, reset); 6897} 6898 6899/* 6900 * Card doesn't have a firmware, install one. 6901 */ 6902int t4_fw_forceinstall(struct adapter *adap, const u8 *fw_data, 6903 unsigned int size) 6904{ 6905 const struct fw_hdr *fw_hdr = (const struct fw_hdr *)fw_data; 6906 unsigned int bootstrap = 6907 be32_to_cpu(fw_hdr->magic) == FW_HDR_MAGIC_BOOTSTRAP; 6908 int ret; 6909 6910 if (!t4_fw_matches_chip(adap, fw_hdr) || bootstrap) 6911 return -EINVAL; 6912 6913 t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, F_UPCRST); 6914 t4_write_reg(adap, A_PCIE_FW, 0); /* Clobber internal state */ 6915 ret = t4_load_fw(adap, fw_data, size); 6916 if (ret < 0) 6917 return ret; 6918 t4_write_reg(adap, A_PL_RST, F_PIORST | F_PIORSTMODE); 6919 msleep(1000); 6920 6921 return (0); 6922} 6923 6924/** 6925 * t4_fw_initialize - ask FW to initialize the device 6926 * @adap: the adapter 6927 * @mbox: mailbox to use for the FW command 6928 * 6929 * Issues a command to FW to partially initialize the device. This 6930 * performs initialization that generally doesn't depend on user input. 6931 */ 6932int t4_fw_initialize(struct adapter *adap, unsigned int mbox) 6933{ 6934 struct fw_initialize_cmd c; 6935 6936 memset(&c, 0, sizeof(c)); 6937 INIT_CMD(c, INITIALIZE, WRITE); 6938 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 6939} 6940 6941/** 6942 * t4_query_params_rw - query FW or device parameters 6943 * @adap: the adapter 6944 * @mbox: mailbox to use for the FW command 6945 * @pf: the PF 6946 * @vf: the VF 6947 * @nparams: the number of parameters 6948 * @params: the parameter names 6949 * @val: the parameter values 6950 * @rw: Write and read flag 6951 * 6952 * Reads the value of FW or device parameters. Up to 7 parameters can be 6953 * queried at once. 6954 */ 6955int t4_query_params_rw(struct adapter *adap, unsigned int mbox, unsigned int pf, 6956 unsigned int vf, unsigned int nparams, const u32 *params, 6957 u32 *val, int rw) 6958{ 6959 int i, ret; 6960 struct fw_params_cmd c; 6961 __be32 *p = &c.param[0].mnem; 6962 6963 if (nparams > 7) 6964 return -EINVAL; 6965 6966 memset(&c, 0, sizeof(c)); 6967 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_PARAMS_CMD) | 6968 F_FW_CMD_REQUEST | F_FW_CMD_READ | 6969 V_FW_PARAMS_CMD_PFN(pf) | 6970 V_FW_PARAMS_CMD_VFN(vf)); 6971 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 6972 6973 for (i = 0; i < nparams; i++) { 6974 *p++ = cpu_to_be32(*params++); 6975 if (rw) 6976 *p = cpu_to_be32(*(val + i)); 6977 p++; 6978 } 6979 6980 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 6981 if (ret == 0) 6982 for (i = 0, p = &c.param[0].val; i < nparams; i++, p += 2) 6983 *val++ = be32_to_cpu(*p); 6984 return ret; 6985} 6986 6987int t4_query_params(struct adapter *adap, unsigned int mbox, unsigned int pf, 6988 unsigned int vf, unsigned int nparams, const u32 *params, 6989 u32 *val) 6990{ 6991 return t4_query_params_rw(adap, mbox, pf, vf, nparams, params, val, 0); 6992} 6993 6994/** 6995 * t4_set_params_timeout - sets FW or device parameters 6996 * @adap: the adapter 6997 * @mbox: mailbox to use for the FW command 6998 * @pf: the PF 6999 * @vf: the VF 7000 * @nparams: the number of parameters 7001 * @params: the parameter names 7002 * @val: the parameter values 7003 * @timeout: the timeout time 7004 * 7005 * Sets the value of FW or device parameters. Up to 7 parameters can be 7006 * specified at once. 7007 */ 7008int t4_set_params_timeout(struct adapter *adap, unsigned int mbox, 7009 unsigned int pf, unsigned int vf, 7010 unsigned int nparams, const u32 *params, 7011 const u32 *val, int timeout) 7012{ 7013 struct fw_params_cmd c; 7014 __be32 *p = &c.param[0].mnem; 7015 7016 if (nparams > 7) 7017 return -EINVAL; 7018 7019 memset(&c, 0, sizeof(c)); 7020 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_PARAMS_CMD) | 7021 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 7022 V_FW_PARAMS_CMD_PFN(pf) | 7023 V_FW_PARAMS_CMD_VFN(vf)); 7024 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 7025 7026 while (nparams--) { 7027 *p++ = cpu_to_be32(*params++); 7028 *p++ = cpu_to_be32(*val++); 7029 } 7030 7031 return t4_wr_mbox_timeout(adap, mbox, &c, sizeof(c), NULL, timeout); 7032} 7033 7034/** 7035 * t4_set_params - sets FW or device parameters 7036 * @adap: the adapter 7037 * @mbox: mailbox to use for the FW command 7038 * @pf: the PF 7039 * @vf: the VF 7040 * @nparams: the number of parameters 7041 * @params: the parameter names 7042 * @val: the parameter values 7043 * 7044 * Sets the value of FW or device parameters. Up to 7 parameters can be 7045 * specified at once. 7046 */ 7047int t4_set_params(struct adapter *adap, unsigned int mbox, unsigned int pf, 7048 unsigned int vf, unsigned int nparams, const u32 *params, 7049 const u32 *val) 7050{ 7051 return t4_set_params_timeout(adap, mbox, pf, vf, nparams, params, val, 7052 FW_CMD_MAX_TIMEOUT); 7053} 7054 7055/** 7056 * t4_cfg_pfvf - configure PF/VF resource limits 7057 * @adap: the adapter 7058 * @mbox: mailbox to use for the FW command 7059 * @pf: the PF being configured 7060 * @vf: the VF being configured 7061 * @txq: the max number of egress queues 7062 * @txq_eth_ctrl: the max number of egress Ethernet or control queues 7063 * @rxqi: the max number of interrupt-capable ingress queues 7064 * @rxq: the max number of interruptless ingress queues 7065 * @tc: the PCI traffic class 7066 * @vi: the max number of virtual interfaces 7067 * @cmask: the channel access rights mask for the PF/VF 7068 * @pmask: the port access rights mask for the PF/VF 7069 * @nexact: the maximum number of exact MPS filters 7070 * @rcaps: read capabilities 7071 * @wxcaps: write/execute capabilities 7072 * 7073 * Configures resource limits and capabilities for a physical or virtual 7074 * function. 7075 */ 7076int t4_cfg_pfvf(struct adapter *adap, unsigned int mbox, unsigned int pf, 7077 unsigned int vf, unsigned int txq, unsigned int txq_eth_ctrl, 7078 unsigned int rxqi, unsigned int rxq, unsigned int tc, 7079 unsigned int vi, unsigned int cmask, unsigned int pmask, 7080 unsigned int nexact, unsigned int rcaps, unsigned int wxcaps) 7081{ 7082 struct fw_pfvf_cmd c; 7083 7084 memset(&c, 0, sizeof(c)); 7085 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_PFVF_CMD) | F_FW_CMD_REQUEST | 7086 F_FW_CMD_WRITE | V_FW_PFVF_CMD_PFN(pf) | 7087 V_FW_PFVF_CMD_VFN(vf)); 7088 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 7089 c.niqflint_niq = cpu_to_be32(V_FW_PFVF_CMD_NIQFLINT(rxqi) | 7090 V_FW_PFVF_CMD_NIQ(rxq)); 7091 c.type_to_neq = cpu_to_be32(V_FW_PFVF_CMD_CMASK(cmask) | 7092 V_FW_PFVF_CMD_PMASK(pmask) | 7093 V_FW_PFVF_CMD_NEQ(txq)); 7094 c.tc_to_nexactf = cpu_to_be32(V_FW_PFVF_CMD_TC(tc) | 7095 V_FW_PFVF_CMD_NVI(vi) | 7096 V_FW_PFVF_CMD_NEXACTF(nexact)); 7097 c.r_caps_to_nethctrl = cpu_to_be32(V_FW_PFVF_CMD_R_CAPS(rcaps) | 7098 V_FW_PFVF_CMD_WX_CAPS(wxcaps) | 7099 V_FW_PFVF_CMD_NETHCTRL(txq_eth_ctrl)); 7100 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7101} 7102 7103/** 7104 * t4_alloc_vi_func - allocate a virtual interface 7105 * @adap: the adapter 7106 * @mbox: mailbox to use for the FW command 7107 * @port: physical port associated with the VI 7108 * @pf: the PF owning the VI 7109 * @vf: the VF owning the VI 7110 * @nmac: number of MAC addresses needed (1 to 5) 7111 * @mac: the MAC addresses of the VI 7112 * @rss_size: size of RSS table slice associated with this VI 7113 * @portfunc: which Port Application Function MAC Address is desired 7114 * @idstype: Intrusion Detection Type 7115 * 7116 * Allocates a virtual interface for the given physical port. If @mac is 7117 * not %NULL it contains the MAC addresses of the VI as assigned by FW. 7118 * If @rss_size is %NULL the VI is not assigned any RSS slice by FW. 7119 * @mac should be large enough to hold @nmac Ethernet addresses, they are 7120 * stored consecutively so the space needed is @nmac * 6 bytes. 7121 * Returns a negative error number or the non-negative VI id. 7122 */ 7123int t4_alloc_vi_func(struct adapter *adap, unsigned int mbox, 7124 unsigned int port, unsigned int pf, unsigned int vf, 7125 unsigned int nmac, u8 *mac, u16 *rss_size, 7126 unsigned int portfunc, unsigned int idstype) 7127{ 7128 int ret; 7129 struct fw_vi_cmd c; 7130 7131 memset(&c, 0, sizeof(c)); 7132 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_VI_CMD) | F_FW_CMD_REQUEST | 7133 F_FW_CMD_WRITE | F_FW_CMD_EXEC | 7134 V_FW_VI_CMD_PFN(pf) | V_FW_VI_CMD_VFN(vf)); 7135 c.alloc_to_len16 = cpu_to_be32(F_FW_VI_CMD_ALLOC | FW_LEN16(c)); 7136 c.type_to_viid = cpu_to_be16(V_FW_VI_CMD_TYPE(idstype) | 7137 V_FW_VI_CMD_FUNC(portfunc)); 7138 c.portid_pkd = V_FW_VI_CMD_PORTID(port); 7139 c.nmac = nmac - 1; 7140 if(!rss_size) 7141 c.norss_rsssize = F_FW_VI_CMD_NORSS; 7142 7143 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 7144 if (ret) 7145 return ret; 7146 7147 if (mac) { 7148 memcpy(mac, c.mac, sizeof(c.mac)); 7149 switch (nmac) { 7150 case 5: 7151 memcpy(mac + 24, c.nmac3, sizeof(c.nmac3)); 7152 case 4: 7153 memcpy(mac + 18, c.nmac2, sizeof(c.nmac2)); 7154 case 3: 7155 memcpy(mac + 12, c.nmac1, sizeof(c.nmac1)); 7156 case 2: 7157 memcpy(mac + 6, c.nmac0, sizeof(c.nmac0)); 7158 } 7159 } 7160 if (rss_size) 7161 *rss_size = G_FW_VI_CMD_RSSSIZE(be16_to_cpu(c.norss_rsssize)); 7162 return G_FW_VI_CMD_VIID(be16_to_cpu(c.type_to_viid)); 7163} 7164 7165/** 7166 * t4_alloc_vi - allocate an [Ethernet Function] virtual interface 7167 * @adap: the adapter 7168 * @mbox: mailbox to use for the FW command 7169 * @port: physical port associated with the VI 7170 * @pf: the PF owning the VI 7171 * @vf: the VF owning the VI 7172 * @nmac: number of MAC addresses needed (1 to 5) 7173 * @mac: the MAC addresses of the VI 7174 * @rss_size: size of RSS table slice associated with this VI 7175 * 7176 * backwards compatible and convieniance routine to allocate a Virtual 7177 * Interface with a Ethernet Port Application Function and Intrustion 7178 * Detection System disabled. 7179 */ 7180int t4_alloc_vi(struct adapter *adap, unsigned int mbox, unsigned int port, 7181 unsigned int pf, unsigned int vf, unsigned int nmac, u8 *mac, 7182 u16 *rss_size) 7183{ 7184 return t4_alloc_vi_func(adap, mbox, port, pf, vf, nmac, mac, rss_size, 7185 FW_VI_FUNC_ETH, 0); 7186} 7187 7188/** 7189 * t4_free_vi - free a virtual interface 7190 * @adap: the adapter 7191 * @mbox: mailbox to use for the FW command 7192 * @pf: the PF owning the VI 7193 * @vf: the VF owning the VI 7194 * @viid: virtual interface identifiler 7195 * 7196 * Free a previously allocated virtual interface. 7197 */ 7198int t4_free_vi(struct adapter *adap, unsigned int mbox, unsigned int pf, 7199 unsigned int vf, unsigned int viid) 7200{ 7201 struct fw_vi_cmd c; 7202 7203 memset(&c, 0, sizeof(c)); 7204 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_VI_CMD) | 7205 F_FW_CMD_REQUEST | 7206 F_FW_CMD_EXEC | 7207 V_FW_VI_CMD_PFN(pf) | 7208 V_FW_VI_CMD_VFN(vf)); 7209 c.alloc_to_len16 = cpu_to_be32(F_FW_VI_CMD_FREE | FW_LEN16(c)); 7210 c.type_to_viid = cpu_to_be16(V_FW_VI_CMD_VIID(viid)); 7211 7212 return t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 7213} 7214 7215/** 7216 * t4_set_rxmode - set Rx properties of a virtual interface 7217 * @adap: the adapter 7218 * @mbox: mailbox to use for the FW command 7219 * @viid: the VI id 7220 * @mtu: the new MTU or -1 7221 * @promisc: 1 to enable promiscuous mode, 0 to disable it, -1 no change 7222 * @all_multi: 1 to enable all-multi mode, 0 to disable it, -1 no change 7223 * @bcast: 1 to enable broadcast Rx, 0 to disable it, -1 no change 7224 * @vlanex: 1 to enable HW VLAN extraction, 0 to disable it, -1 no change 7225 * @sleep_ok: if true we may sleep while awaiting command completion 7226 * 7227 * Sets Rx properties of a virtual interface. 7228 */ 7229int t4_set_rxmode(struct adapter *adap, unsigned int mbox, unsigned int viid, 7230 int mtu, int promisc, int all_multi, int bcast, int vlanex, 7231 bool sleep_ok) 7232{ 7233 struct fw_vi_rxmode_cmd c; 7234 7235 /* convert to FW values */ 7236 if (mtu < 0) 7237 mtu = M_FW_VI_RXMODE_CMD_MTU; 7238 if (promisc < 0) 7239 promisc = M_FW_VI_RXMODE_CMD_PROMISCEN; 7240 if (all_multi < 0) 7241 all_multi = M_FW_VI_RXMODE_CMD_ALLMULTIEN; 7242 if (bcast < 0) 7243 bcast = M_FW_VI_RXMODE_CMD_BROADCASTEN; 7244 if (vlanex < 0) 7245 vlanex = M_FW_VI_RXMODE_CMD_VLANEXEN; 7246 7247 memset(&c, 0, sizeof(c)); 7248 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_RXMODE_CMD) | 7249 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 7250 V_FW_VI_RXMODE_CMD_VIID(viid)); 7251 c.retval_len16 = cpu_to_be32(FW_LEN16(c)); 7252 c.mtu_to_vlanexen = 7253 cpu_to_be32(V_FW_VI_RXMODE_CMD_MTU(mtu) | 7254 V_FW_VI_RXMODE_CMD_PROMISCEN(promisc) | 7255 V_FW_VI_RXMODE_CMD_ALLMULTIEN(all_multi) | 7256 V_FW_VI_RXMODE_CMD_BROADCASTEN(bcast) | 7257 V_FW_VI_RXMODE_CMD_VLANEXEN(vlanex)); 7258 return t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), NULL, sleep_ok); 7259} 7260 7261/** 7262 * t4_alloc_mac_filt - allocates exact-match filters for MAC addresses 7263 * @adap: the adapter 7264 * @mbox: mailbox to use for the FW command 7265 * @viid: the VI id 7266 * @free: if true any existing filters for this VI id are first removed 7267 * @naddr: the number of MAC addresses to allocate filters for (up to 7) 7268 * @addr: the MAC address(es) 7269 * @idx: where to store the index of each allocated filter 7270 * @hash: pointer to hash address filter bitmap 7271 * @sleep_ok: call is allowed to sleep 7272 * 7273 * Allocates an exact-match filter for each of the supplied addresses and 7274 * sets it to the corresponding address. If @idx is not %NULL it should 7275 * have at least @naddr entries, each of which will be set to the index of 7276 * the filter allocated for the corresponding MAC address. If a filter 7277 * could not be allocated for an address its index is set to 0xffff. 7278 * If @hash is not %NULL addresses that fail to allocate an exact filter 7279 * are hashed and update the hash filter bitmap pointed at by @hash. 7280 * 7281 * Returns a negative error number or the number of filters allocated. 7282 */ 7283int t4_alloc_mac_filt(struct adapter *adap, unsigned int mbox, 7284 unsigned int viid, bool free, unsigned int naddr, 7285 const u8 **addr, u16 *idx, u64 *hash, bool sleep_ok) 7286{ 7287 int offset, ret = 0; 7288 struct fw_vi_mac_cmd c; 7289 unsigned int nfilters = 0; 7290 unsigned int max_naddr = adap->chip_params->mps_tcam_size; 7291 unsigned int rem = naddr; 7292 7293 if (naddr > max_naddr) 7294 return -EINVAL; 7295 7296 for (offset = 0; offset < naddr ; /**/) { 7297 unsigned int fw_naddr = (rem < ARRAY_SIZE(c.u.exact) 7298 ? rem 7299 : ARRAY_SIZE(c.u.exact)); 7300 size_t len16 = DIV_ROUND_UP(offsetof(struct fw_vi_mac_cmd, 7301 u.exact[fw_naddr]), 16); 7302 struct fw_vi_mac_exact *p; 7303 int i; 7304 7305 memset(&c, 0, sizeof(c)); 7306 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_MAC_CMD) | 7307 F_FW_CMD_REQUEST | 7308 F_FW_CMD_WRITE | 7309 V_FW_CMD_EXEC(free) | 7310 V_FW_VI_MAC_CMD_VIID(viid)); 7311 c.freemacs_to_len16 = cpu_to_be32(V_FW_VI_MAC_CMD_FREEMACS(free) | 7312 V_FW_CMD_LEN16(len16)); 7313 7314 for (i = 0, p = c.u.exact; i < fw_naddr; i++, p++) { 7315 p->valid_to_idx = 7316 cpu_to_be16(F_FW_VI_MAC_CMD_VALID | 7317 V_FW_VI_MAC_CMD_IDX(FW_VI_MAC_ADD_MAC)); 7318 memcpy(p->macaddr, addr[offset+i], sizeof(p->macaddr)); 7319 } 7320 7321 /* 7322 * It's okay if we run out of space in our MAC address arena. 7323 * Some of the addresses we submit may get stored so we need 7324 * to run through the reply to see what the results were ... 7325 */ 7326 ret = t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), &c, sleep_ok); 7327 if (ret && ret != -FW_ENOMEM) 7328 break; 7329 7330 for (i = 0, p = c.u.exact; i < fw_naddr; i++, p++) { 7331 u16 index = G_FW_VI_MAC_CMD_IDX( 7332 be16_to_cpu(p->valid_to_idx)); 7333 7334 if (idx) 7335 idx[offset+i] = (index >= max_naddr 7336 ? 0xffff 7337 : index); 7338 if (index < max_naddr) 7339 nfilters++; 7340 else if (hash) 7341 *hash |= (1ULL << hash_mac_addr(addr[offset+i])); 7342 } 7343 7344 free = false; 7345 offset += fw_naddr; 7346 rem -= fw_naddr; 7347 } 7348 7349 if (ret == 0 || ret == -FW_ENOMEM) 7350 ret = nfilters; 7351 return ret; 7352} 7353 7354/** 7355 * t4_change_mac - modifies the exact-match filter for a MAC address 7356 * @adap: the adapter 7357 * @mbox: mailbox to use for the FW command 7358 * @viid: the VI id 7359 * @idx: index of existing filter for old value of MAC address, or -1 7360 * @addr: the new MAC address value 7361 * @persist: whether a new MAC allocation should be persistent 7362 * @add_smt: if true also add the address to the HW SMT 7363 * 7364 * Modifies an exact-match filter and sets it to the new MAC address if 7365 * @idx >= 0, or adds the MAC address to a new filter if @idx < 0. In the 7366 * latter case the address is added persistently if @persist is %true. 7367 * 7368 * Note that in general it is not possible to modify the value of a given 7369 * filter so the generic way to modify an address filter is to free the one 7370 * being used by the old address value and allocate a new filter for the 7371 * new address value. 7372 * 7373 * Returns a negative error number or the index of the filter with the new 7374 * MAC value. Note that this index may differ from @idx. 7375 */ 7376int t4_change_mac(struct adapter *adap, unsigned int mbox, unsigned int viid, 7377 int idx, const u8 *addr, bool persist, bool add_smt) 7378{ 7379 int ret, mode; 7380 struct fw_vi_mac_cmd c; 7381 struct fw_vi_mac_exact *p = c.u.exact; 7382 unsigned int max_mac_addr = adap->chip_params->mps_tcam_size; 7383 7384 if (idx < 0) /* new allocation */ 7385 idx = persist ? FW_VI_MAC_ADD_PERSIST_MAC : FW_VI_MAC_ADD_MAC; 7386 mode = add_smt ? FW_VI_MAC_SMT_AND_MPSTCAM : FW_VI_MAC_MPS_TCAM_ENTRY; 7387 7388 memset(&c, 0, sizeof(c)); 7389 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_MAC_CMD) | 7390 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 7391 V_FW_VI_MAC_CMD_VIID(viid)); 7392 c.freemacs_to_len16 = cpu_to_be32(V_FW_CMD_LEN16(1)); 7393 p->valid_to_idx = cpu_to_be16(F_FW_VI_MAC_CMD_VALID | 7394 V_FW_VI_MAC_CMD_SMAC_RESULT(mode) | 7395 V_FW_VI_MAC_CMD_IDX(idx)); 7396 memcpy(p->macaddr, addr, sizeof(p->macaddr)); 7397 7398 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 7399 if (ret == 0) { 7400 ret = G_FW_VI_MAC_CMD_IDX(be16_to_cpu(p->valid_to_idx)); 7401 if (ret >= max_mac_addr) 7402 ret = -ENOMEM; 7403 } 7404 return ret; 7405} 7406 7407/** 7408 * t4_set_addr_hash - program the MAC inexact-match hash filter 7409 * @adap: the adapter 7410 * @mbox: mailbox to use for the FW command 7411 * @viid: the VI id 7412 * @ucast: whether the hash filter should also match unicast addresses 7413 * @vec: the value to be written to the hash filter 7414 * @sleep_ok: call is allowed to sleep 7415 * 7416 * Sets the 64-bit inexact-match hash filter for a virtual interface. 7417 */ 7418int t4_set_addr_hash(struct adapter *adap, unsigned int mbox, unsigned int viid, 7419 bool ucast, u64 vec, bool sleep_ok) 7420{ 7421 struct fw_vi_mac_cmd c; 7422 u32 val; 7423 7424 memset(&c, 0, sizeof(c)); 7425 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_MAC_CMD) | 7426 F_FW_CMD_REQUEST | F_FW_CMD_WRITE | 7427 V_FW_VI_ENABLE_CMD_VIID(viid)); 7428 val = V_FW_VI_MAC_CMD_ENTRY_TYPE(FW_VI_MAC_TYPE_HASHVEC) | 7429 V_FW_VI_MAC_CMD_HASHUNIEN(ucast) | V_FW_CMD_LEN16(1); 7430 c.freemacs_to_len16 = cpu_to_be32(val); 7431 c.u.hash.hashvec = cpu_to_be64(vec); 7432 return t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), NULL, sleep_ok); 7433} 7434 7435/** 7436 * t4_enable_vi_params - enable/disable a virtual interface 7437 * @adap: the adapter 7438 * @mbox: mailbox to use for the FW command 7439 * @viid: the VI id 7440 * @rx_en: 1=enable Rx, 0=disable Rx 7441 * @tx_en: 1=enable Tx, 0=disable Tx 7442 * @dcb_en: 1=enable delivery of Data Center Bridging messages. 7443 * 7444 * Enables/disables a virtual interface. Note that setting DCB Enable 7445 * only makes sense when enabling a Virtual Interface ... 7446 */ 7447int t4_enable_vi_params(struct adapter *adap, unsigned int mbox, 7448 unsigned int viid, bool rx_en, bool tx_en, bool dcb_en) 7449{ 7450 struct fw_vi_enable_cmd c; 7451 7452 memset(&c, 0, sizeof(c)); 7453 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_ENABLE_CMD) | 7454 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 7455 V_FW_VI_ENABLE_CMD_VIID(viid)); 7456 c.ien_to_len16 = cpu_to_be32(V_FW_VI_ENABLE_CMD_IEN(rx_en) | 7457 V_FW_VI_ENABLE_CMD_EEN(tx_en) | 7458 V_FW_VI_ENABLE_CMD_DCB_INFO(dcb_en) | 7459 FW_LEN16(c)); 7460 return t4_wr_mbox_ns(adap, mbox, &c, sizeof(c), NULL); 7461} 7462 7463/** 7464 * t4_enable_vi - enable/disable a virtual interface 7465 * @adap: the adapter 7466 * @mbox: mailbox to use for the FW command 7467 * @viid: the VI id 7468 * @rx_en: 1=enable Rx, 0=disable Rx 7469 * @tx_en: 1=enable Tx, 0=disable Tx 7470 * 7471 * Enables/disables a virtual interface. Note that setting DCB Enable 7472 * only makes sense when enabling a Virtual Interface ... 7473 */ 7474int t4_enable_vi(struct adapter *adap, unsigned int mbox, unsigned int viid, 7475 bool rx_en, bool tx_en) 7476{ 7477 return t4_enable_vi_params(adap, mbox, viid, rx_en, tx_en, 0); 7478} 7479 7480/** 7481 * t4_identify_port - identify a VI's port by blinking its LED 7482 * @adap: the adapter 7483 * @mbox: mailbox to use for the FW command 7484 * @viid: the VI id 7485 * @nblinks: how many times to blink LED at 2.5 Hz 7486 * 7487 * Identifies a VI's port by blinking its LED. 7488 */ 7489int t4_identify_port(struct adapter *adap, unsigned int mbox, unsigned int viid, 7490 unsigned int nblinks) 7491{ 7492 struct fw_vi_enable_cmd c; 7493 7494 memset(&c, 0, sizeof(c)); 7495 c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_ENABLE_CMD) | 7496 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 7497 V_FW_VI_ENABLE_CMD_VIID(viid)); 7498 c.ien_to_len16 = cpu_to_be32(F_FW_VI_ENABLE_CMD_LED | FW_LEN16(c)); 7499 c.blinkdur = cpu_to_be16(nblinks); 7500 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7501} 7502 7503/** 7504 * t4_iq_stop - stop an ingress queue and its FLs 7505 * @adap: the adapter 7506 * @mbox: mailbox to use for the FW command 7507 * @pf: the PF owning the queues 7508 * @vf: the VF owning the queues 7509 * @iqtype: the ingress queue type (FW_IQ_TYPE_FL_INT_CAP, etc.) 7510 * @iqid: ingress queue id 7511 * @fl0id: FL0 queue id or 0xffff if no attached FL0 7512 * @fl1id: FL1 queue id or 0xffff if no attached FL1 7513 * 7514 * Stops an ingress queue and its associated FLs, if any. This causes 7515 * any current or future data/messages destined for these queues to be 7516 * tossed. 7517 */ 7518int t4_iq_stop(struct adapter *adap, unsigned int mbox, unsigned int pf, 7519 unsigned int vf, unsigned int iqtype, unsigned int iqid, 7520 unsigned int fl0id, unsigned int fl1id) 7521{ 7522 struct fw_iq_cmd c; 7523 7524 memset(&c, 0, sizeof(c)); 7525 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_IQ_CMD) | F_FW_CMD_REQUEST | 7526 F_FW_CMD_EXEC | V_FW_IQ_CMD_PFN(pf) | 7527 V_FW_IQ_CMD_VFN(vf)); 7528 c.alloc_to_len16 = cpu_to_be32(F_FW_IQ_CMD_IQSTOP | FW_LEN16(c)); 7529 c.type_to_iqandstindex = cpu_to_be32(V_FW_IQ_CMD_TYPE(iqtype)); 7530 c.iqid = cpu_to_be16(iqid); 7531 c.fl0id = cpu_to_be16(fl0id); 7532 c.fl1id = cpu_to_be16(fl1id); 7533 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7534} 7535 7536/** 7537 * t4_iq_free - free an ingress queue and its FLs 7538 * @adap: the adapter 7539 * @mbox: mailbox to use for the FW command 7540 * @pf: the PF owning the queues 7541 * @vf: the VF owning the queues 7542 * @iqtype: the ingress queue type (FW_IQ_TYPE_FL_INT_CAP, etc.) 7543 * @iqid: ingress queue id 7544 * @fl0id: FL0 queue id or 0xffff if no attached FL0 7545 * @fl1id: FL1 queue id or 0xffff if no attached FL1 7546 * 7547 * Frees an ingress queue and its associated FLs, if any. 7548 */ 7549int t4_iq_free(struct adapter *adap, unsigned int mbox, unsigned int pf, 7550 unsigned int vf, unsigned int iqtype, unsigned int iqid, 7551 unsigned int fl0id, unsigned int fl1id) 7552{ 7553 struct fw_iq_cmd c; 7554 7555 memset(&c, 0, sizeof(c)); 7556 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_IQ_CMD) | F_FW_CMD_REQUEST | 7557 F_FW_CMD_EXEC | V_FW_IQ_CMD_PFN(pf) | 7558 V_FW_IQ_CMD_VFN(vf)); 7559 c.alloc_to_len16 = cpu_to_be32(F_FW_IQ_CMD_FREE | FW_LEN16(c)); 7560 c.type_to_iqandstindex = cpu_to_be32(V_FW_IQ_CMD_TYPE(iqtype)); 7561 c.iqid = cpu_to_be16(iqid); 7562 c.fl0id = cpu_to_be16(fl0id); 7563 c.fl1id = cpu_to_be16(fl1id); 7564 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7565} 7566 7567/** 7568 * t4_eth_eq_free - free an Ethernet egress queue 7569 * @adap: the adapter 7570 * @mbox: mailbox to use for the FW command 7571 * @pf: the PF owning the queue 7572 * @vf: the VF owning the queue 7573 * @eqid: egress queue id 7574 * 7575 * Frees an Ethernet egress queue. 7576 */ 7577int t4_eth_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf, 7578 unsigned int vf, unsigned int eqid) 7579{ 7580 struct fw_eq_eth_cmd c; 7581 7582 memset(&c, 0, sizeof(c)); 7583 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_EQ_ETH_CMD) | 7584 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 7585 V_FW_EQ_ETH_CMD_PFN(pf) | 7586 V_FW_EQ_ETH_CMD_VFN(vf)); 7587 c.alloc_to_len16 = cpu_to_be32(F_FW_EQ_ETH_CMD_FREE | FW_LEN16(c)); 7588 c.eqid_pkd = cpu_to_be32(V_FW_EQ_ETH_CMD_EQID(eqid)); 7589 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7590} 7591 7592/** 7593 * t4_ctrl_eq_free - free a control egress queue 7594 * @adap: the adapter 7595 * @mbox: mailbox to use for the FW command 7596 * @pf: the PF owning the queue 7597 * @vf: the VF owning the queue 7598 * @eqid: egress queue id 7599 * 7600 * Frees a control egress queue. 7601 */ 7602int t4_ctrl_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf, 7603 unsigned int vf, unsigned int eqid) 7604{ 7605 struct fw_eq_ctrl_cmd c; 7606 7607 memset(&c, 0, sizeof(c)); 7608 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_EQ_CTRL_CMD) | 7609 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 7610 V_FW_EQ_CTRL_CMD_PFN(pf) | 7611 V_FW_EQ_CTRL_CMD_VFN(vf)); 7612 c.alloc_to_len16 = cpu_to_be32(F_FW_EQ_CTRL_CMD_FREE | FW_LEN16(c)); 7613 c.cmpliqid_eqid = cpu_to_be32(V_FW_EQ_CTRL_CMD_EQID(eqid)); 7614 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7615} 7616 7617/** 7618 * t4_ofld_eq_free - free an offload egress queue 7619 * @adap: the adapter 7620 * @mbox: mailbox to use for the FW command 7621 * @pf: the PF owning the queue 7622 * @vf: the VF owning the queue 7623 * @eqid: egress queue id 7624 * 7625 * Frees a control egress queue. 7626 */ 7627int t4_ofld_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf, 7628 unsigned int vf, unsigned int eqid) 7629{ 7630 struct fw_eq_ofld_cmd c; 7631 7632 memset(&c, 0, sizeof(c)); 7633 c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_EQ_OFLD_CMD) | 7634 F_FW_CMD_REQUEST | F_FW_CMD_EXEC | 7635 V_FW_EQ_OFLD_CMD_PFN(pf) | 7636 V_FW_EQ_OFLD_CMD_VFN(vf)); 7637 c.alloc_to_len16 = cpu_to_be32(F_FW_EQ_OFLD_CMD_FREE | FW_LEN16(c)); 7638 c.eqid_pkd = cpu_to_be32(V_FW_EQ_OFLD_CMD_EQID(eqid)); 7639 return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); 7640} 7641 7642/** 7643 * t4_link_down_rc_str - return a string for a Link Down Reason Code 7644 * @link_down_rc: Link Down Reason Code 7645 * 7646 * Returns a string representation of the Link Down Reason Code. 7647 */ 7648const char *t4_link_down_rc_str(unsigned char link_down_rc) 7649{ 7650 static const char *reason[] = { 7651 "Link Down", 7652 "Remote Fault", 7653 "Auto-negotiation Failure", 7654 "Reserved3", 7655 "Insufficient Airflow", 7656 "Unable To Determine Reason", 7657 "No RX Signal Detected", 7658 "Reserved7", 7659 }; 7660 7661 if (link_down_rc >= ARRAY_SIZE(reason)) 7662 return "Bad Reason Code"; 7663 7664 return reason[link_down_rc]; 7665} 7666 7667/* 7668 * Updates all fields owned by the common code in port_info and link_config 7669 * based on information provided by the firmware. Does not touch any 7670 * requested_* field. 7671 */ 7672static void handle_port_info(struct port_info *pi, const struct fw_port_info *p) 7673{ 7674 struct link_config *lc = &pi->link_cfg; 7675 int speed; 7676 unsigned char fc, fec; 7677 u32 stat = be32_to_cpu(p->lstatus_to_modtype); 7678 7679 pi->port_type = G_FW_PORT_CMD_PTYPE(stat); 7680 pi->mod_type = G_FW_PORT_CMD_MODTYPE(stat); 7681 pi->mdio_addr = stat & F_FW_PORT_CMD_MDIOCAP ? 7682 G_FW_PORT_CMD_MDIOADDR(stat) : -1; 7683 7684 lc->supported = be16_to_cpu(p->pcap); 7685 lc->advertising = be16_to_cpu(p->acap); 7686 lc->lp_advertising = be16_to_cpu(p->lpacap); 7687 lc->link_ok = (stat & F_FW_PORT_CMD_LSTATUS) != 0; 7688 lc->link_down_rc = G_FW_PORT_CMD_LINKDNRC(stat); 7689 7690 speed = 0; 7691 if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_100M)) 7692 speed = 100; 7693 else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_1G)) 7694 speed = 1000; 7695 else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_10G)) 7696 speed = 10000; 7697 else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_25G)) 7698 speed = 25000; 7699 else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_40G)) 7700 speed = 40000; 7701 else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_100G)) 7702 speed = 100000; 7703 lc->speed = speed; 7704 7705 fc = 0; 7706 if (stat & F_FW_PORT_CMD_RXPAUSE) 7707 fc |= PAUSE_RX; 7708 if (stat & F_FW_PORT_CMD_TXPAUSE) 7709 fc |= PAUSE_TX; 7710 lc->fc = fc; 7711 7712 fec = 0; 7713 if (lc->advertising & FW_PORT_CAP_FEC_RS) 7714 fec |= FEC_RS; 7715 if (lc->advertising & FW_PORT_CAP_FEC_BASER_RS) 7716 fec |= FEC_BASER_RS; 7717 if (lc->advertising & FW_PORT_CAP_FEC_RESERVED) 7718 fec |= FEC_RESERVED; 7719 lc->fec = fec; 7720} 7721 7722/** 7723 * t4_update_port_info - retrieve and update port information if changed 7724 * @pi: the port_info 7725 * 7726 * We issue a Get Port Information Command to the Firmware and, if 7727 * successful, we check to see if anything is different from what we 7728 * last recorded and update things accordingly. 7729 */ 7730 int t4_update_port_info(struct port_info *pi) 7731 { 7732 struct fw_port_cmd port_cmd; 7733 int ret; 7734 7735 memset(&port_cmd, 0, sizeof port_cmd); 7736 port_cmd.op_to_portid = cpu_to_be32(V_FW_CMD_OP(FW_PORT_CMD) | 7737 F_FW_CMD_REQUEST | F_FW_CMD_READ | 7738 V_FW_PORT_CMD_PORTID(pi->tx_chan)); 7739 port_cmd.action_to_len16 = cpu_to_be32( 7740 V_FW_PORT_CMD_ACTION(FW_PORT_ACTION_GET_PORT_INFO) | 7741 FW_LEN16(port_cmd)); 7742 ret = t4_wr_mbox_ns(pi->adapter, pi->adapter->mbox, 7743 &port_cmd, sizeof(port_cmd), &port_cmd); 7744 if (ret) 7745 return ret; 7746 7747 handle_port_info(pi, &port_cmd.u.info); 7748 return 0; 7749} 7750 7751/** 7752 * t4_handle_fw_rpl - process a FW reply message 7753 * @adap: the adapter 7754 * @rpl: start of the FW message 7755 * 7756 * Processes a FW message, such as link state change messages. 7757 */ 7758int t4_handle_fw_rpl(struct adapter *adap, const __be64 *rpl) 7759{ 7760 u8 opcode = *(const u8 *)rpl; 7761 const struct fw_port_cmd *p = (const void *)rpl; 7762 unsigned int action = 7763 G_FW_PORT_CMD_ACTION(be32_to_cpu(p->action_to_len16)); 7764 7765 if (opcode == FW_PORT_CMD && action == FW_PORT_ACTION_GET_PORT_INFO) { 7766 /* link/module state change message */ 7767 int i, old_ptype, old_mtype; 7768 int chan = G_FW_PORT_CMD_PORTID(be32_to_cpu(p->op_to_portid)); 7769 struct port_info *pi = NULL; 7770 struct link_config *lc, *old_lc; 7771 7772 for_each_port(adap, i) { 7773 pi = adap2pinfo(adap, i); 7774 if (pi->tx_chan == chan) 7775 break; 7776 } 7777 7778 lc = &pi->link_cfg; 7779 old_lc = &pi->old_link_cfg; 7780 old_ptype = pi->port_type; 7781 old_mtype = pi->mod_type; 7782 7783 handle_port_info(pi, &p->u.info); 7784 if (old_ptype != pi->port_type || old_mtype != pi->mod_type) { 7785 t4_os_portmod_changed(pi); 7786 } 7787 if (old_lc->link_ok != lc->link_ok || 7788 old_lc->speed != lc->speed || 7789 old_lc->fec != lc->fec || 7790 old_lc->fc != lc->fc) { 7791 t4_os_link_changed(pi); 7792 *old_lc = *lc; 7793 } 7794 } else { 7795 CH_WARN_RATELIMIT(adap, "Unknown firmware reply %d\n", opcode); 7796 return -EINVAL; 7797 } 7798 return 0; 7799} 7800 7801/** 7802 * get_pci_mode - determine a card's PCI mode 7803 * @adapter: the adapter 7804 * @p: where to store the PCI settings 7805 * 7806 * Determines a card's PCI mode and associated parameters, such as speed 7807 * and width. 7808 */ 7809static void get_pci_mode(struct adapter *adapter, 7810 struct pci_params *p) 7811{ 7812 u16 val; 7813 u32 pcie_cap; 7814 7815 pcie_cap = t4_os_find_pci_capability(adapter, PCI_CAP_ID_EXP); 7816 if (pcie_cap) { 7817 t4_os_pci_read_cfg2(adapter, pcie_cap + PCI_EXP_LNKSTA, &val); 7818 p->speed = val & PCI_EXP_LNKSTA_CLS; 7819 p->width = (val & PCI_EXP_LNKSTA_NLW) >> 4; 7820 } 7821} 7822 7823struct flash_desc { 7824 u32 vendor_and_model_id; 7825 u32 size_mb; 7826}; 7827 7828int t4_get_flash_params(struct adapter *adapter) 7829{ 7830 /* 7831 * Table for non-standard supported Flash parts. Note, all Flash 7832 * parts must have 64KB sectors. 7833 */ 7834 static struct flash_desc supported_flash[] = { 7835 { 0x00150201, 4 << 20 }, /* Spansion 4MB S25FL032P */ 7836 }; 7837 7838 int ret; 7839 u32 flashid = 0; 7840 unsigned int part, manufacturer; 7841 unsigned int density, size; 7842 7843 7844 /* 7845 * Issue a Read ID Command to the Flash part. We decode supported 7846 * Flash parts and their sizes from this. There's a newer Query 7847 * Command which can retrieve detailed geometry information but many 7848 * Flash parts don't support it. 7849 */ 7850 ret = sf1_write(adapter, 1, 1, 0, SF_RD_ID); 7851 if (!ret) 7852 ret = sf1_read(adapter, 3, 0, 1, &flashid); 7853 t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ 7854 if (ret < 0) 7855 return ret; 7856 7857 /* 7858 * Check to see if it's one of our non-standard supported Flash parts. 7859 */ 7860 for (part = 0; part < ARRAY_SIZE(supported_flash); part++) 7861 if (supported_flash[part].vendor_and_model_id == flashid) { 7862 adapter->params.sf_size = 7863 supported_flash[part].size_mb; 7864 adapter->params.sf_nsec = 7865 adapter->params.sf_size / SF_SEC_SIZE; 7866 goto found; 7867 } 7868 7869 /* 7870 * Decode Flash part size. The code below looks repetative with 7871 * common encodings, but that's not guaranteed in the JEDEC 7872 * specification for the Read JADEC ID command. The only thing that 7873 * we're guaranteed by the JADEC specification is where the 7874 * Manufacturer ID is in the returned result. After that each 7875 * Manufacturer ~could~ encode things completely differently. 7876 * Note, all Flash parts must have 64KB sectors. 7877 */ 7878 manufacturer = flashid & 0xff; 7879 switch (manufacturer) { 7880 case 0x20: { /* Micron/Numonix */ 7881 /* 7882 * This Density -> Size decoding table is taken from Micron 7883 * Data Sheets. 7884 */ 7885 density = (flashid >> 16) & 0xff; 7886 switch (density) { 7887 case 0x14: size = 1 << 20; break; /* 1MB */ 7888 case 0x15: size = 1 << 21; break; /* 2MB */ 7889 case 0x16: size = 1 << 22; break; /* 4MB */ 7890 case 0x17: size = 1 << 23; break; /* 8MB */ 7891 case 0x18: size = 1 << 24; break; /* 16MB */ 7892 case 0x19: size = 1 << 25; break; /* 32MB */ 7893 case 0x20: size = 1 << 26; break; /* 64MB */ 7894 case 0x21: size = 1 << 27; break; /* 128MB */ 7895 case 0x22: size = 1 << 28; break; /* 256MB */ 7896 7897 default: 7898 CH_ERR(adapter, "Micron Flash Part has bad size, " 7899 "ID = %#x, Density code = %#x\n", 7900 flashid, density); 7901 return -EINVAL; 7902 } 7903 break; 7904 } 7905 7906 case 0xef: { /* Winbond */ 7907 /* 7908 * This Density -> Size decoding table is taken from Winbond 7909 * Data Sheets. 7910 */ 7911 density = (flashid >> 16) & 0xff; 7912 switch (density) { 7913 case 0x17: size = 1 << 23; break; /* 8MB */ 7914 case 0x18: size = 1 << 24; break; /* 16MB */ 7915 7916 default: 7917 CH_ERR(adapter, "Winbond Flash Part has bad size, " 7918 "ID = %#x, Density code = %#x\n", 7919 flashid, density); 7920 return -EINVAL; 7921 } 7922 break; 7923 } 7924 7925 default: 7926 CH_ERR(adapter, "Unsupported Flash Part, ID = %#x\n", flashid); 7927 return -EINVAL; 7928 } 7929 7930 /* 7931 * Store decoded Flash size and fall through into vetting code. 7932 */ 7933 adapter->params.sf_size = size; 7934 adapter->params.sf_nsec = size / SF_SEC_SIZE; 7935 7936 found: 7937 /* 7938 * We should ~probably~ reject adapters with FLASHes which are too 7939 * small but we have some legacy FPGAs with small FLASHes that we'd 7940 * still like to use. So instead we emit a scary message ... 7941 */ 7942 if (adapter->params.sf_size < FLASH_MIN_SIZE) 7943 CH_WARN(adapter, "WARNING: Flash Part ID %#x, size %#x < %#x\n", 7944 flashid, adapter->params.sf_size, FLASH_MIN_SIZE); 7945 7946 return 0; 7947} 7948 7949static void set_pcie_completion_timeout(struct adapter *adapter, 7950 u8 range) 7951{ 7952 u16 val; 7953 u32 pcie_cap; 7954 7955 pcie_cap = t4_os_find_pci_capability(adapter, PCI_CAP_ID_EXP); 7956 if (pcie_cap) { 7957 t4_os_pci_read_cfg2(adapter, pcie_cap + PCI_EXP_DEVCTL2, &val); 7958 val &= 0xfff0; 7959 val |= range ; 7960 t4_os_pci_write_cfg2(adapter, pcie_cap + PCI_EXP_DEVCTL2, val); 7961 } 7962} 7963 7964const struct chip_params *t4_get_chip_params(int chipid) 7965{ 7966 static const struct chip_params chip_params[] = { 7967 { 7968 /* T4 */ 7969 .nchan = NCHAN, 7970 .pm_stats_cnt = PM_NSTATS, 7971 .cng_ch_bits_log = 2, 7972 .nsched_cls = 15, 7973 .cim_num_obq = CIM_NUM_OBQ, 7974 .mps_rplc_size = 128, 7975 .vfcount = 128, 7976 .sge_fl_db = F_DBPRIO, 7977 .mps_tcam_size = NUM_MPS_CLS_SRAM_L_INSTANCES, 7978 }, 7979 { 7980 /* T5 */ 7981 .nchan = NCHAN, 7982 .pm_stats_cnt = PM_NSTATS, 7983 .cng_ch_bits_log = 2, 7984 .nsched_cls = 16, 7985 .cim_num_obq = CIM_NUM_OBQ_T5, 7986 .mps_rplc_size = 128, 7987 .vfcount = 128, 7988 .sge_fl_db = F_DBPRIO | F_DBTYPE, 7989 .mps_tcam_size = NUM_MPS_T5_CLS_SRAM_L_INSTANCES, 7990 }, 7991 { 7992 /* T6 */ 7993 .nchan = T6_NCHAN, 7994 .pm_stats_cnt = T6_PM_NSTATS, 7995 .cng_ch_bits_log = 3, 7996 .nsched_cls = 16, 7997 .cim_num_obq = CIM_NUM_OBQ_T5, 7998 .mps_rplc_size = 256, 7999 .vfcount = 256, 8000 .sge_fl_db = 0, 8001 .mps_tcam_size = NUM_MPS_T5_CLS_SRAM_L_INSTANCES, 8002 }, 8003 }; 8004 8005 chipid -= CHELSIO_T4; 8006 if (chipid < 0 || chipid >= ARRAY_SIZE(chip_params)) 8007 return NULL; 8008 8009 return &chip_params[chipid]; 8010} 8011 8012/** 8013 * t4_prep_adapter - prepare SW and HW for operation 8014 * @adapter: the adapter 8015 * @buf: temporary space of at least VPD_LEN size provided by the caller. 8016 * 8017 * Initialize adapter SW state for the various HW modules, set initial 8018 * values for some adapter tunables, take PHYs out of reset, and 8019 * initialize the MDIO interface. 8020 */ 8021int t4_prep_adapter(struct adapter *adapter, u32 *buf) 8022{ 8023 int ret; 8024 uint16_t device_id; 8025 uint32_t pl_rev; 8026 8027 get_pci_mode(adapter, &adapter->params.pci); 8028 8029 pl_rev = t4_read_reg(adapter, A_PL_REV); 8030 adapter->params.chipid = G_CHIPID(pl_rev); 8031 adapter->params.rev = G_REV(pl_rev); 8032 if (adapter->params.chipid == 0) { 8033 /* T4 did not have chipid in PL_REV (T5 onwards do) */ 8034 adapter->params.chipid = CHELSIO_T4; 8035 8036 /* T4A1 chip is not supported */ 8037 if (adapter->params.rev == 1) { 8038 CH_ALERT(adapter, "T4 rev 1 chip is not supported.\n"); 8039 return -EINVAL; 8040 } 8041 } 8042 8043 adapter->chip_params = t4_get_chip_params(chip_id(adapter)); 8044 if (adapter->chip_params == NULL) 8045 return -EINVAL; 8046 8047 adapter->params.pci.vpd_cap_addr = 8048 t4_os_find_pci_capability(adapter, PCI_CAP_ID_VPD); 8049 8050 ret = t4_get_flash_params(adapter); 8051 if (ret < 0) 8052 return ret; 8053 8054 ret = get_vpd_params(adapter, &adapter->params.vpd, buf); 8055 if (ret < 0) 8056 return ret; 8057 8058 /* Cards with real ASICs have the chipid in the PCIe device id */ 8059 t4_os_pci_read_cfg2(adapter, PCI_DEVICE_ID, &device_id); 8060 if (device_id >> 12 == chip_id(adapter)) 8061 adapter->params.cim_la_size = CIMLA_SIZE; 8062 else { 8063 /* FPGA */ 8064 adapter->params.fpga = 1; 8065 adapter->params.cim_la_size = 2 * CIMLA_SIZE; 8066 } 8067 8068 init_cong_ctrl(adapter->params.a_wnd, adapter->params.b_wnd); 8069 8070 /* 8071 * Default port and clock for debugging in case we can't reach FW. 8072 */ 8073 adapter->params.nports = 1; 8074 adapter->params.portvec = 1; 8075 adapter->params.vpd.cclk = 50000; 8076 8077 /* Set pci completion timeout value to 4 seconds. */ 8078 set_pcie_completion_timeout(adapter, 0xd); 8079 return 0; 8080} 8081 8082/** 8083 * t4_shutdown_adapter - shut down adapter, host & wire 8084 * @adapter: the adapter 8085 * 8086 * Perform an emergency shutdown of the adapter and stop it from 8087 * continuing any further communication on the ports or DMA to the 8088 * host. This is typically used when the adapter and/or firmware 8089 * have crashed and we want to prevent any further accidental 8090 * communication with the rest of the world. This will also force 8091 * the port Link Status to go down -- if register writes work -- 8092 * which should help our peers figure out that we're down. 8093 */ 8094int t4_shutdown_adapter(struct adapter *adapter) 8095{ 8096 int port; 8097 8098 t4_intr_disable(adapter); 8099 t4_write_reg(adapter, A_DBG_GPIO_EN, 0); 8100 for_each_port(adapter, port) { 8101 u32 a_port_cfg = is_t4(adapter) ? 8102 PORT_REG(port, A_XGMAC_PORT_CFG) : 8103 T5_PORT_REG(port, A_MAC_PORT_CFG); 8104 8105 t4_write_reg(adapter, a_port_cfg, 8106 t4_read_reg(adapter, a_port_cfg) 8107 & ~V_SIGNAL_DET(1)); 8108 } 8109 t4_set_reg_field(adapter, A_SGE_CONTROL, F_GLOBALENABLE, 0); 8110 8111 return 0; 8112} 8113 8114/** 8115 * t4_bar2_sge_qregs - return BAR2 SGE Queue register information 8116 * @adapter: the adapter 8117 * @qid: the Queue ID 8118 * @qtype: the Ingress or Egress type for @qid 8119 * @user: true if this request is for a user mode queue 8120 * @pbar2_qoffset: BAR2 Queue Offset 8121 * @pbar2_qid: BAR2 Queue ID or 0 for Queue ID inferred SGE Queues 8122 * 8123 * Returns the BAR2 SGE Queue Registers information associated with the 8124 * indicated Absolute Queue ID. These are passed back in return value 8125 * pointers. @qtype should be T4_BAR2_QTYPE_EGRESS for Egress Queue 8126 * and T4_BAR2_QTYPE_INGRESS for Ingress Queues. 8127 * 8128 * This may return an error which indicates that BAR2 SGE Queue 8129 * registers aren't available. If an error is not returned, then the 8130 * following values are returned: 8131 * 8132 * *@pbar2_qoffset: the BAR2 Offset of the @qid Registers 8133 * *@pbar2_qid: the BAR2 SGE Queue ID or 0 of @qid 8134 * 8135 * If the returned BAR2 Queue ID is 0, then BAR2 SGE registers which 8136 * require the "Inferred Queue ID" ability may be used. E.g. the 8137 * Write Combining Doorbell Buffer. If the BAR2 Queue ID is not 0, 8138 * then these "Inferred Queue ID" register may not be used. 8139 */ 8140int t4_bar2_sge_qregs(struct adapter *adapter, 8141 unsigned int qid, 8142 enum t4_bar2_qtype qtype, 8143 int user, 8144 u64 *pbar2_qoffset, 8145 unsigned int *pbar2_qid) 8146{ 8147 unsigned int page_shift, page_size, qpp_shift, qpp_mask; 8148 u64 bar2_page_offset, bar2_qoffset; 8149 unsigned int bar2_qid, bar2_qid_offset, bar2_qinferred; 8150 8151 /* T4 doesn't support BAR2 SGE Queue registers for kernel 8152 * mode queues. 8153 */ 8154 if (!user && is_t4(adapter)) 8155 return -EINVAL; 8156 8157 /* Get our SGE Page Size parameters. 8158 */ 8159 page_shift = adapter->params.sge.page_shift; 8160 page_size = 1 << page_shift; 8161 8162 /* Get the right Queues per Page parameters for our Queue. 8163 */ 8164 qpp_shift = (qtype == T4_BAR2_QTYPE_EGRESS 8165 ? adapter->params.sge.eq_s_qpp 8166 : adapter->params.sge.iq_s_qpp); 8167 qpp_mask = (1 << qpp_shift) - 1; 8168 8169 /* Calculate the basics of the BAR2 SGE Queue register area: 8170 * o The BAR2 page the Queue registers will be in. 8171 * o The BAR2 Queue ID. 8172 * o The BAR2 Queue ID Offset into the BAR2 page. 8173 */ 8174 bar2_page_offset = ((u64)(qid >> qpp_shift) << page_shift); 8175 bar2_qid = qid & qpp_mask; 8176 bar2_qid_offset = bar2_qid * SGE_UDB_SIZE; 8177 8178 /* If the BAR2 Queue ID Offset is less than the Page Size, then the 8179 * hardware will infer the Absolute Queue ID simply from the writes to 8180 * the BAR2 Queue ID Offset within the BAR2 Page (and we need to use a 8181 * BAR2 Queue ID of 0 for those writes). Otherwise, we'll simply 8182 * write to the first BAR2 SGE Queue Area within the BAR2 Page with 8183 * the BAR2 Queue ID and the hardware will infer the Absolute Queue ID 8184 * from the BAR2 Page and BAR2 Queue ID. 8185 * 8186 * One important censequence of this is that some BAR2 SGE registers 8187 * have a "Queue ID" field and we can write the BAR2 SGE Queue ID 8188 * there. But other registers synthesize the SGE Queue ID purely 8189 * from the writes to the registers -- the Write Combined Doorbell 8190 * Buffer is a good example. These BAR2 SGE Registers are only 8191 * available for those BAR2 SGE Register areas where the SGE Absolute 8192 * Queue ID can be inferred from simple writes. 8193 */ 8194 bar2_qoffset = bar2_page_offset; 8195 bar2_qinferred = (bar2_qid_offset < page_size); 8196 if (bar2_qinferred) { 8197 bar2_qoffset += bar2_qid_offset; 8198 bar2_qid = 0; 8199 } 8200 8201 *pbar2_qoffset = bar2_qoffset; 8202 *pbar2_qid = bar2_qid; 8203 return 0; 8204} 8205 8206/** 8207 * t4_init_devlog_params - initialize adapter->params.devlog 8208 * @adap: the adapter 8209 * @fw_attach: whether we can talk to the firmware 8210 * 8211 * Initialize various fields of the adapter's Firmware Device Log 8212 * Parameters structure. 8213 */ 8214int t4_init_devlog_params(struct adapter *adap, int fw_attach) 8215{ 8216 struct devlog_params *dparams = &adap->params.devlog; 8217 u32 pf_dparams; 8218 unsigned int devlog_meminfo; 8219 struct fw_devlog_cmd devlog_cmd; 8220 int ret; 8221 8222 /* If we're dealing with newer firmware, the Device Log Paramerters 8223 * are stored in a designated register which allows us to access the 8224 * Device Log even if we can't talk to the firmware. 8225 */ 8226 pf_dparams = 8227 t4_read_reg(adap, PCIE_FW_REG(A_PCIE_FW_PF, PCIE_FW_PF_DEVLOG)); 8228 if (pf_dparams) { 8229 unsigned int nentries, nentries128; 8230 8231 dparams->memtype = G_PCIE_FW_PF_DEVLOG_MEMTYPE(pf_dparams); 8232 dparams->start = G_PCIE_FW_PF_DEVLOG_ADDR16(pf_dparams) << 4; 8233 8234 nentries128 = G_PCIE_FW_PF_DEVLOG_NENTRIES128(pf_dparams); 8235 nentries = (nentries128 + 1) * 128; 8236 dparams->size = nentries * sizeof(struct fw_devlog_e); 8237 8238 return 0; 8239 } 8240 8241 /* 8242 * For any failing returns ... 8243 */ 8244 memset(dparams, 0, sizeof *dparams); 8245 8246 /* 8247 * If we can't talk to the firmware, there's really nothing we can do 8248 * at this point. 8249 */ 8250 if (!fw_attach) 8251 return -ENXIO; 8252 8253 /* Otherwise, ask the firmware for it's Device Log Parameters. 8254 */ 8255 memset(&devlog_cmd, 0, sizeof devlog_cmd); 8256 devlog_cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_DEVLOG_CMD) | 8257 F_FW_CMD_REQUEST | F_FW_CMD_READ); 8258 devlog_cmd.retval_len16 = cpu_to_be32(FW_LEN16(devlog_cmd)); 8259 ret = t4_wr_mbox(adap, adap->mbox, &devlog_cmd, sizeof(devlog_cmd), 8260 &devlog_cmd); 8261 if (ret) 8262 return ret; 8263 8264 devlog_meminfo = 8265 be32_to_cpu(devlog_cmd.memtype_devlog_memaddr16_devlog); 8266 dparams->memtype = G_FW_DEVLOG_CMD_MEMTYPE_DEVLOG(devlog_meminfo); 8267 dparams->start = G_FW_DEVLOG_CMD_MEMADDR16_DEVLOG(devlog_meminfo) << 4; 8268 dparams->size = be32_to_cpu(devlog_cmd.memsize_devlog); 8269 8270 return 0; 8271} 8272 8273/** 8274 * t4_init_sge_params - initialize adap->params.sge 8275 * @adapter: the adapter 8276 * 8277 * Initialize various fields of the adapter's SGE Parameters structure. 8278 */ 8279int t4_init_sge_params(struct adapter *adapter) 8280{ 8281 u32 r; 8282 struct sge_params *sp = &adapter->params.sge; 8283 unsigned i, tscale = 1; 8284 8285 r = t4_read_reg(adapter, A_SGE_INGRESS_RX_THRESHOLD); 8286 sp->counter_val[0] = G_THRESHOLD_0(r); 8287 sp->counter_val[1] = G_THRESHOLD_1(r); 8288 sp->counter_val[2] = G_THRESHOLD_2(r); 8289 sp->counter_val[3] = G_THRESHOLD_3(r); 8290 8291 if (chip_id(adapter) >= CHELSIO_T6) { 8292 r = t4_read_reg(adapter, A_SGE_ITP_CONTROL); 8293 tscale = G_TSCALE(r); 8294 if (tscale == 0) 8295 tscale = 1; 8296 else 8297 tscale += 2; 8298 } 8299 8300 r = t4_read_reg(adapter, A_SGE_TIMER_VALUE_0_AND_1); 8301 sp->timer_val[0] = core_ticks_to_us(adapter, G_TIMERVALUE0(r)) * tscale; 8302 sp->timer_val[1] = core_ticks_to_us(adapter, G_TIMERVALUE1(r)) * tscale; 8303 r = t4_read_reg(adapter, A_SGE_TIMER_VALUE_2_AND_3); 8304 sp->timer_val[2] = core_ticks_to_us(adapter, G_TIMERVALUE2(r)) * tscale; 8305 sp->timer_val[3] = core_ticks_to_us(adapter, G_TIMERVALUE3(r)) * tscale; 8306 r = t4_read_reg(adapter, A_SGE_TIMER_VALUE_4_AND_5); 8307 sp->timer_val[4] = core_ticks_to_us(adapter, G_TIMERVALUE4(r)) * tscale; 8308 sp->timer_val[5] = core_ticks_to_us(adapter, G_TIMERVALUE5(r)) * tscale; 8309 8310 r = t4_read_reg(adapter, A_SGE_CONM_CTRL); 8311 sp->fl_starve_threshold = G_EGRTHRESHOLD(r) * 2 + 1; 8312 if (is_t4(adapter)) 8313 sp->fl_starve_threshold2 = sp->fl_starve_threshold; 8314 else if (is_t5(adapter)) 8315 sp->fl_starve_threshold2 = G_EGRTHRESHOLDPACKING(r) * 2 + 1; 8316 else 8317 sp->fl_starve_threshold2 = G_T6_EGRTHRESHOLDPACKING(r) * 2 + 1; 8318 8319 /* egress queues: log2 of # of doorbells per BAR2 page */ 8320 r = t4_read_reg(adapter, A_SGE_EGRESS_QUEUES_PER_PAGE_PF); 8321 r >>= S_QUEUESPERPAGEPF0 + 8322 (S_QUEUESPERPAGEPF1 - S_QUEUESPERPAGEPF0) * adapter->pf; 8323 sp->eq_s_qpp = r & M_QUEUESPERPAGEPF0; 8324 8325 /* ingress queues: log2 of # of doorbells per BAR2 page */ 8326 r = t4_read_reg(adapter, A_SGE_INGRESS_QUEUES_PER_PAGE_PF); 8327 r >>= S_QUEUESPERPAGEPF0 + 8328 (S_QUEUESPERPAGEPF1 - S_QUEUESPERPAGEPF0) * adapter->pf; 8329 sp->iq_s_qpp = r & M_QUEUESPERPAGEPF0; 8330 8331 r = t4_read_reg(adapter, A_SGE_HOST_PAGE_SIZE); 8332 r >>= S_HOSTPAGESIZEPF0 + 8333 (S_HOSTPAGESIZEPF1 - S_HOSTPAGESIZEPF0) * adapter->pf; 8334 sp->page_shift = (r & M_HOSTPAGESIZEPF0) + 10; 8335 8336 r = t4_read_reg(adapter, A_SGE_CONTROL); 8337 sp->sge_control = r; 8338 sp->spg_len = r & F_EGRSTATUSPAGESIZE ? 128 : 64; 8339 sp->fl_pktshift = G_PKTSHIFT(r); 8340 if (chip_id(adapter) <= CHELSIO_T5) { 8341 sp->pad_boundary = 1 << (G_INGPADBOUNDARY(r) + 8342 X_INGPADBOUNDARY_SHIFT); 8343 } else { 8344 sp->pad_boundary = 1 << (G_INGPADBOUNDARY(r) + 8345 X_T6_INGPADBOUNDARY_SHIFT); 8346 } 8347 if (is_t4(adapter)) 8348 sp->pack_boundary = sp->pad_boundary; 8349 else { 8350 r = t4_read_reg(adapter, A_SGE_CONTROL2); 8351 if (G_INGPACKBOUNDARY(r) == 0) 8352 sp->pack_boundary = 16; 8353 else 8354 sp->pack_boundary = 1 << (G_INGPACKBOUNDARY(r) + 5); 8355 } 8356 for (i = 0; i < SGE_FLBUF_SIZES; i++) 8357 sp->sge_fl_buffer_size[i] = t4_read_reg(adapter, 8358 A_SGE_FL_BUFFER_SIZE0 + (4 * i)); 8359 8360 return 0; 8361} 8362 8363/* 8364 * Read and cache the adapter's compressed filter mode and ingress config. 8365 */ 8366static void read_filter_mode_and_ingress_config(struct adapter *adap, 8367 bool sleep_ok) 8368{ 8369 struct tp_params *tpp = &adap->params.tp; 8370 8371 t4_tp_pio_read(adap, &tpp->vlan_pri_map, 1, A_TP_VLAN_PRI_MAP, 8372 sleep_ok); 8373 t4_tp_pio_read(adap, &tpp->ingress_config, 1, A_TP_INGRESS_CONFIG, 8374 sleep_ok); 8375 8376 /* 8377 * Now that we have TP_VLAN_PRI_MAP cached, we can calculate the field 8378 * shift positions of several elements of the Compressed Filter Tuple 8379 * for this adapter which we need frequently ... 8380 */ 8381 tpp->fcoe_shift = t4_filter_field_shift(adap, F_FCOE); 8382 tpp->port_shift = t4_filter_field_shift(adap, F_PORT); 8383 tpp->vnic_shift = t4_filter_field_shift(adap, F_VNIC_ID); 8384 tpp->vlan_shift = t4_filter_field_shift(adap, F_VLAN); 8385 tpp->tos_shift = t4_filter_field_shift(adap, F_TOS); 8386 tpp->protocol_shift = t4_filter_field_shift(adap, F_PROTOCOL); 8387 tpp->ethertype_shift = t4_filter_field_shift(adap, F_ETHERTYPE); 8388 tpp->macmatch_shift = t4_filter_field_shift(adap, F_MACMATCH); 8389 tpp->matchtype_shift = t4_filter_field_shift(adap, F_MPSHITTYPE); 8390 tpp->frag_shift = t4_filter_field_shift(adap, F_FRAGMENTATION); 8391 8392 /* 8393 * If TP_INGRESS_CONFIG.VNID == 0, then TP_VLAN_PRI_MAP.VNIC_ID 8394 * represents the presence of an Outer VLAN instead of a VNIC ID. 8395 */ 8396 if ((tpp->ingress_config & F_VNIC) == 0) 8397 tpp->vnic_shift = -1; 8398} 8399 8400/** 8401 * t4_init_tp_params - initialize adap->params.tp 8402 * @adap: the adapter 8403 * 8404 * Initialize various fields of the adapter's TP Parameters structure. 8405 */ 8406int t4_init_tp_params(struct adapter *adap, bool sleep_ok) 8407{ 8408 int chan; 8409 u32 v; 8410 struct tp_params *tpp = &adap->params.tp; 8411 8412 v = t4_read_reg(adap, A_TP_TIMER_RESOLUTION); 8413 tpp->tre = G_TIMERRESOLUTION(v); 8414 tpp->dack_re = G_DELAYEDACKRESOLUTION(v); 8415 8416 /* MODQ_REQ_MAP defaults to setting queues 0-3 to chan 0-3 */ 8417 for (chan = 0; chan < MAX_NCHAN; chan++) 8418 tpp->tx_modq[chan] = chan; 8419 8420 read_filter_mode_and_ingress_config(adap, sleep_ok); 8421 8422 /* 8423 * Cache a mask of the bits that represent the error vector portion of 8424 * rx_pkt.err_vec. T6+ can use a compressed error vector to make room 8425 * for information about outer encapsulation (GENEVE/VXLAN/NVGRE). 8426 */ 8427 tpp->err_vec_mask = htobe16(0xffff); 8428 if (chip_id(adap) > CHELSIO_T5) { 8429 v = t4_read_reg(adap, A_TP_OUT_CONFIG); 8430 if (v & F_CRXPKTENC) { 8431 tpp->err_vec_mask = 8432 htobe16(V_T6_COMPR_RXERR_VEC(M_T6_COMPR_RXERR_VEC)); 8433 } 8434 } 8435 8436 return 0; 8437} 8438 8439/** 8440 * t4_filter_field_shift - calculate filter field shift 8441 * @adap: the adapter 8442 * @filter_sel: the desired field (from TP_VLAN_PRI_MAP bits) 8443 * 8444 * Return the shift position of a filter field within the Compressed 8445 * Filter Tuple. The filter field is specified via its selection bit 8446 * within TP_VLAN_PRI_MAL (filter mode). E.g. F_VLAN. 8447 */ 8448int t4_filter_field_shift(const struct adapter *adap, int filter_sel) 8449{ 8450 unsigned int filter_mode = adap->params.tp.vlan_pri_map; 8451 unsigned int sel; 8452 int field_shift; 8453 8454 if ((filter_mode & filter_sel) == 0) 8455 return -1; 8456 8457 for (sel = 1, field_shift = 0; sel < filter_sel; sel <<= 1) { 8458 switch (filter_mode & sel) { 8459 case F_FCOE: 8460 field_shift += W_FT_FCOE; 8461 break; 8462 case F_PORT: 8463 field_shift += W_FT_PORT; 8464 break; 8465 case F_VNIC_ID: 8466 field_shift += W_FT_VNIC_ID; 8467 break; 8468 case F_VLAN: 8469 field_shift += W_FT_VLAN; 8470 break; 8471 case F_TOS: 8472 field_shift += W_FT_TOS; 8473 break; 8474 case F_PROTOCOL: 8475 field_shift += W_FT_PROTOCOL; 8476 break; 8477 case F_ETHERTYPE: 8478 field_shift += W_FT_ETHERTYPE; 8479 break; 8480 case F_MACMATCH: 8481 field_shift += W_FT_MACMATCH; 8482 break; 8483 case F_MPSHITTYPE: 8484 field_shift += W_FT_MPSHITTYPE; 8485 break; 8486 case F_FRAGMENTATION: 8487 field_shift += W_FT_FRAGMENTATION; 8488 break; 8489 } 8490 } 8491 return field_shift; 8492} 8493 8494int t4_port_init(struct adapter *adap, int mbox, int pf, int vf, int port_id) 8495{ 8496 u8 addr[6]; 8497 int ret, i, j; 8498 u16 rss_size; 8499 struct port_info *p = adap2pinfo(adap, port_id); 8500 u32 param, val; 8501 8502 for (i = 0, j = -1; i <= p->port_id; i++) { 8503 do { 8504 j++; 8505 } while ((adap->params.portvec & (1 << j)) == 0); 8506 } 8507 8508 if (!(adap->flags & IS_VF) || 8509 adap->params.vfres.r_caps & FW_CMD_CAP_PORT) { 8510 t4_update_port_info(p); 8511 } 8512 8513 ret = t4_alloc_vi(adap, mbox, j, pf, vf, 1, addr, &rss_size); 8514 if (ret < 0) 8515 return ret; 8516 8517 p->vi[0].viid = ret; 8518 if (chip_id(adap) <= CHELSIO_T5) 8519 p->vi[0].smt_idx = (ret & 0x7f) << 1; 8520 else 8521 p->vi[0].smt_idx = (ret & 0x7f); 8522 p->tx_chan = j; 8523 p->mps_bg_map = t4_get_mps_bg_map(adap, j); 8524 p->rx_e_chan_map = t4_get_rx_e_chan_map(adap, j); 8525 p->lport = j; 8526 p->vi[0].rss_size = rss_size; 8527 t4_os_set_hw_addr(p, addr); 8528 8529 param = V_FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) | 8530 V_FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_RSSINFO) | 8531 V_FW_PARAMS_PARAM_YZ(p->vi[0].viid); 8532 ret = t4_query_params(adap, mbox, pf, vf, 1, ¶m, &val); 8533 if (ret) 8534 p->vi[0].rss_base = 0xffff; 8535 else { 8536 /* MPASS((val >> 16) == rss_size); */ 8537 p->vi[0].rss_base = val & 0xffff; 8538 } 8539 8540 return 0; 8541} 8542 8543/** 8544 * t4_read_cimq_cfg - read CIM queue configuration 8545 * @adap: the adapter 8546 * @base: holds the queue base addresses in bytes 8547 * @size: holds the queue sizes in bytes 8548 * @thres: holds the queue full thresholds in bytes 8549 * 8550 * Returns the current configuration of the CIM queues, starting with 8551 * the IBQs, then the OBQs. 8552 */ 8553void t4_read_cimq_cfg(struct adapter *adap, u16 *base, u16 *size, u16 *thres) 8554{ 8555 unsigned int i, v; 8556 int cim_num_obq = adap->chip_params->cim_num_obq; 8557 8558 for (i = 0; i < CIM_NUM_IBQ; i++) { 8559 t4_write_reg(adap, A_CIM_QUEUE_CONFIG_REF, F_IBQSELECT | 8560 V_QUENUMSELECT(i)); 8561 v = t4_read_reg(adap, A_CIM_QUEUE_CONFIG_CTRL); 8562 /* value is in 256-byte units */ 8563 *base++ = G_CIMQBASE(v) * 256; 8564 *size++ = G_CIMQSIZE(v) * 256; 8565 *thres++ = G_QUEFULLTHRSH(v) * 8; /* 8-byte unit */ 8566 } 8567 for (i = 0; i < cim_num_obq; i++) { 8568 t4_write_reg(adap, A_CIM_QUEUE_CONFIG_REF, F_OBQSELECT | 8569 V_QUENUMSELECT(i)); 8570 v = t4_read_reg(adap, A_CIM_QUEUE_CONFIG_CTRL); 8571 /* value is in 256-byte units */ 8572 *base++ = G_CIMQBASE(v) * 256; 8573 *size++ = G_CIMQSIZE(v) * 256; 8574 } 8575} 8576 8577/** 8578 * t4_read_cim_ibq - read the contents of a CIM inbound queue 8579 * @adap: the adapter 8580 * @qid: the queue index 8581 * @data: where to store the queue contents 8582 * @n: capacity of @data in 32-bit words 8583 * 8584 * Reads the contents of the selected CIM queue starting at address 0 up 8585 * to the capacity of @data. @n must be a multiple of 4. Returns < 0 on 8586 * error and the number of 32-bit words actually read on success. 8587 */ 8588int t4_read_cim_ibq(struct adapter *adap, unsigned int qid, u32 *data, size_t n) 8589{ 8590 int i, err, attempts; 8591 unsigned int addr; 8592 const unsigned int nwords = CIM_IBQ_SIZE * 4; 8593 8594 if (qid > 5 || (n & 3)) 8595 return -EINVAL; 8596 8597 addr = qid * nwords; 8598 if (n > nwords) 8599 n = nwords; 8600 8601 /* It might take 3-10ms before the IBQ debug read access is allowed. 8602 * Wait for 1 Sec with a delay of 1 usec. 8603 */ 8604 attempts = 1000000; 8605 8606 for (i = 0; i < n; i++, addr++) { 8607 t4_write_reg(adap, A_CIM_IBQ_DBG_CFG, V_IBQDBGADDR(addr) | 8608 F_IBQDBGEN); 8609 err = t4_wait_op_done(adap, A_CIM_IBQ_DBG_CFG, F_IBQDBGBUSY, 0, 8610 attempts, 1); 8611 if (err) 8612 return err; 8613 *data++ = t4_read_reg(adap, A_CIM_IBQ_DBG_DATA); 8614 } 8615 t4_write_reg(adap, A_CIM_IBQ_DBG_CFG, 0); 8616 return i; 8617} 8618 8619/** 8620 * t4_read_cim_obq - read the contents of a CIM outbound queue 8621 * @adap: the adapter 8622 * @qid: the queue index 8623 * @data: where to store the queue contents 8624 * @n: capacity of @data in 32-bit words 8625 * 8626 * Reads the contents of the selected CIM queue starting at address 0 up 8627 * to the capacity of @data. @n must be a multiple of 4. Returns < 0 on 8628 * error and the number of 32-bit words actually read on success. 8629 */ 8630int t4_read_cim_obq(struct adapter *adap, unsigned int qid, u32 *data, size_t n) 8631{ 8632 int i, err; 8633 unsigned int addr, v, nwords; 8634 int cim_num_obq = adap->chip_params->cim_num_obq; 8635 8636 if ((qid > (cim_num_obq - 1)) || (n & 3)) 8637 return -EINVAL; 8638 8639 t4_write_reg(adap, A_CIM_QUEUE_CONFIG_REF, F_OBQSELECT | 8640 V_QUENUMSELECT(qid)); 8641 v = t4_read_reg(adap, A_CIM_QUEUE_CONFIG_CTRL); 8642 8643 addr = G_CIMQBASE(v) * 64; /* muliple of 256 -> muliple of 4 */ 8644 nwords = G_CIMQSIZE(v) * 64; /* same */ 8645 if (n > nwords) 8646 n = nwords; 8647 8648 for (i = 0; i < n; i++, addr++) { 8649 t4_write_reg(adap, A_CIM_OBQ_DBG_CFG, V_OBQDBGADDR(addr) | 8650 F_OBQDBGEN); 8651 err = t4_wait_op_done(adap, A_CIM_OBQ_DBG_CFG, F_OBQDBGBUSY, 0, 8652 2, 1); 8653 if (err) 8654 return err; 8655 *data++ = t4_read_reg(adap, A_CIM_OBQ_DBG_DATA); 8656 } 8657 t4_write_reg(adap, A_CIM_OBQ_DBG_CFG, 0); 8658 return i; 8659} 8660 8661enum { 8662 CIM_QCTL_BASE = 0, 8663 CIM_CTL_BASE = 0x2000, 8664 CIM_PBT_ADDR_BASE = 0x2800, 8665 CIM_PBT_LRF_BASE = 0x3000, 8666 CIM_PBT_DATA_BASE = 0x3800 8667}; 8668 8669/** 8670 * t4_cim_read - read a block from CIM internal address space 8671 * @adap: the adapter 8672 * @addr: the start address within the CIM address space 8673 * @n: number of words to read 8674 * @valp: where to store the result 8675 * 8676 * Reads a block of 4-byte words from the CIM intenal address space. 8677 */ 8678int t4_cim_read(struct adapter *adap, unsigned int addr, unsigned int n, 8679 unsigned int *valp) 8680{ 8681 int ret = 0; 8682 8683 if (t4_read_reg(adap, A_CIM_HOST_ACC_CTRL) & F_HOSTBUSY) 8684 return -EBUSY; 8685 8686 for ( ; !ret && n--; addr += 4) { 8687 t4_write_reg(adap, A_CIM_HOST_ACC_CTRL, addr); 8688 ret = t4_wait_op_done(adap, A_CIM_HOST_ACC_CTRL, F_HOSTBUSY, 8689 0, 5, 2); 8690 if (!ret) 8691 *valp++ = t4_read_reg(adap, A_CIM_HOST_ACC_DATA); 8692 } 8693 return ret; 8694} 8695 8696/** 8697 * t4_cim_write - write a block into CIM internal address space 8698 * @adap: the adapter 8699 * @addr: the start address within the CIM address space 8700 * @n: number of words to write 8701 * @valp: set of values to write 8702 * 8703 * Writes a block of 4-byte words into the CIM intenal address space. 8704 */ 8705int t4_cim_write(struct adapter *adap, unsigned int addr, unsigned int n, 8706 const unsigned int *valp) 8707{ 8708 int ret = 0; 8709 8710 if (t4_read_reg(adap, A_CIM_HOST_ACC_CTRL) & F_HOSTBUSY) 8711 return -EBUSY; 8712 8713 for ( ; !ret && n--; addr += 4) { 8714 t4_write_reg(adap, A_CIM_HOST_ACC_DATA, *valp++); 8715 t4_write_reg(adap, A_CIM_HOST_ACC_CTRL, addr | F_HOSTWRITE); 8716 ret = t4_wait_op_done(adap, A_CIM_HOST_ACC_CTRL, F_HOSTBUSY, 8717 0, 5, 2); 8718 } 8719 return ret; 8720} 8721 8722static int t4_cim_write1(struct adapter *adap, unsigned int addr, 8723 unsigned int val) 8724{ 8725 return t4_cim_write(adap, addr, 1, &val); 8726} 8727 8728/** 8729 * t4_cim_ctl_read - read a block from CIM control region 8730 * @adap: the adapter 8731 * @addr: the start address within the CIM control region 8732 * @n: number of words to read 8733 * @valp: where to store the result 8734 * 8735 * Reads a block of 4-byte words from the CIM control region. 8736 */ 8737int t4_cim_ctl_read(struct adapter *adap, unsigned int addr, unsigned int n, 8738 unsigned int *valp) 8739{ 8740 return t4_cim_read(adap, addr + CIM_CTL_BASE, n, valp); 8741} 8742 8743/** 8744 * t4_cim_read_la - read CIM LA capture buffer 8745 * @adap: the adapter 8746 * @la_buf: where to store the LA data 8747 * @wrptr: the HW write pointer within the capture buffer 8748 * 8749 * Reads the contents of the CIM LA buffer with the most recent entry at 8750 * the end of the returned data and with the entry at @wrptr first. 8751 * We try to leave the LA in the running state we find it in. 8752 */ 8753int t4_cim_read_la(struct adapter *adap, u32 *la_buf, unsigned int *wrptr) 8754{ 8755 int i, ret; 8756 unsigned int cfg, val, idx; 8757 8758 ret = t4_cim_read(adap, A_UP_UP_DBG_LA_CFG, 1, &cfg); 8759 if (ret) 8760 return ret; 8761 8762 if (cfg & F_UPDBGLAEN) { /* LA is running, freeze it */ 8763 ret = t4_cim_write1(adap, A_UP_UP_DBG_LA_CFG, 0); 8764 if (ret) 8765 return ret; 8766 } 8767 8768 ret = t4_cim_read(adap, A_UP_UP_DBG_LA_CFG, 1, &val); 8769 if (ret) 8770 goto restart; 8771 8772 idx = G_UPDBGLAWRPTR(val); 8773 if (wrptr) 8774 *wrptr = idx; 8775 8776 for (i = 0; i < adap->params.cim_la_size; i++) { 8777 ret = t4_cim_write1(adap, A_UP_UP_DBG_LA_CFG, 8778 V_UPDBGLARDPTR(idx) | F_UPDBGLARDEN); 8779 if (ret) 8780 break; 8781 ret = t4_cim_read(adap, A_UP_UP_DBG_LA_CFG, 1, &val); 8782 if (ret) 8783 break; 8784 if (val & F_UPDBGLARDEN) { 8785 ret = -ETIMEDOUT; 8786 break; 8787 } 8788 ret = t4_cim_read(adap, A_UP_UP_DBG_LA_DATA, 1, &la_buf[i]); 8789 if (ret) 8790 break; 8791 8792 /* address can't exceed 0xfff (UpDbgLaRdPtr is of 12-bits) */ 8793 idx = (idx + 1) & M_UPDBGLARDPTR; 8794 /* 8795 * Bits 0-3 of UpDbgLaRdPtr can be between 0000 to 1001 to 8796 * identify the 32-bit portion of the full 312-bit data 8797 */ 8798 if (is_t6(adap)) 8799 while ((idx & 0xf) > 9) 8800 idx = (idx + 1) % M_UPDBGLARDPTR; 8801 } 8802restart: 8803 if (cfg & F_UPDBGLAEN) { 8804 int r = t4_cim_write1(adap, A_UP_UP_DBG_LA_CFG, 8805 cfg & ~F_UPDBGLARDEN); 8806 if (!ret) 8807 ret = r; 8808 } 8809 return ret; 8810} 8811 8812/** 8813 * t4_tp_read_la - read TP LA capture buffer 8814 * @adap: the adapter 8815 * @la_buf: where to store the LA data 8816 * @wrptr: the HW write pointer within the capture buffer 8817 * 8818 * Reads the contents of the TP LA buffer with the most recent entry at 8819 * the end of the returned data and with the entry at @wrptr first. 8820 * We leave the LA in the running state we find it in. 8821 */ 8822void t4_tp_read_la(struct adapter *adap, u64 *la_buf, unsigned int *wrptr) 8823{ 8824 bool last_incomplete; 8825 unsigned int i, cfg, val, idx; 8826 8827 cfg = t4_read_reg(adap, A_TP_DBG_LA_CONFIG) & 0xffff; 8828 if (cfg & F_DBGLAENABLE) /* freeze LA */ 8829 t4_write_reg(adap, A_TP_DBG_LA_CONFIG, 8830 adap->params.tp.la_mask | (cfg ^ F_DBGLAENABLE)); 8831 8832 val = t4_read_reg(adap, A_TP_DBG_LA_CONFIG); 8833 idx = G_DBGLAWPTR(val); 8834 last_incomplete = G_DBGLAMODE(val) >= 2 && (val & F_DBGLAWHLF) == 0; 8835 if (last_incomplete) 8836 idx = (idx + 1) & M_DBGLARPTR; 8837 if (wrptr) 8838 *wrptr = idx; 8839 8840 val &= 0xffff; 8841 val &= ~V_DBGLARPTR(M_DBGLARPTR); 8842 val |= adap->params.tp.la_mask; 8843 8844 for (i = 0; i < TPLA_SIZE; i++) { 8845 t4_write_reg(adap, A_TP_DBG_LA_CONFIG, V_DBGLARPTR(idx) | val); 8846 la_buf[i] = t4_read_reg64(adap, A_TP_DBG_LA_DATAL); 8847 idx = (idx + 1) & M_DBGLARPTR; 8848 } 8849 8850 /* Wipe out last entry if it isn't valid */ 8851 if (last_incomplete) 8852 la_buf[TPLA_SIZE - 1] = ~0ULL; 8853 8854 if (cfg & F_DBGLAENABLE) /* restore running state */ 8855 t4_write_reg(adap, A_TP_DBG_LA_CONFIG, 8856 cfg | adap->params.tp.la_mask); 8857} 8858 8859/* 8860 * SGE Hung Ingress DMA Warning Threshold time and Warning Repeat Rate (in 8861 * seconds). If we find one of the SGE Ingress DMA State Machines in the same 8862 * state for more than the Warning Threshold then we'll issue a warning about 8863 * a potential hang. We'll repeat the warning as the SGE Ingress DMA Channel 8864 * appears to be hung every Warning Repeat second till the situation clears. 8865 * If the situation clears, we'll note that as well. 8866 */ 8867#define SGE_IDMA_WARN_THRESH 1 8868#define SGE_IDMA_WARN_REPEAT 300 8869 8870/** 8871 * t4_idma_monitor_init - initialize SGE Ingress DMA Monitor 8872 * @adapter: the adapter 8873 * @idma: the adapter IDMA Monitor state 8874 * 8875 * Initialize the state of an SGE Ingress DMA Monitor. 8876 */ 8877void t4_idma_monitor_init(struct adapter *adapter, 8878 struct sge_idma_monitor_state *idma) 8879{ 8880 /* Initialize the state variables for detecting an SGE Ingress DMA 8881 * hang. The SGE has internal counters which count up on each clock 8882 * tick whenever the SGE finds its Ingress DMA State Engines in the 8883 * same state they were on the previous clock tick. The clock used is 8884 * the Core Clock so we have a limit on the maximum "time" they can 8885 * record; typically a very small number of seconds. For instance, 8886 * with a 600MHz Core Clock, we can only count up to a bit more than 8887 * 7s. So we'll synthesize a larger counter in order to not run the 8888 * risk of having the "timers" overflow and give us the flexibility to 8889 * maintain a Hung SGE State Machine of our own which operates across 8890 * a longer time frame. 8891 */ 8892 idma->idma_1s_thresh = core_ticks_per_usec(adapter) * 1000000; /* 1s */ 8893 idma->idma_stalled[0] = idma->idma_stalled[1] = 0; 8894} 8895 8896/** 8897 * t4_idma_monitor - monitor SGE Ingress DMA state 8898 * @adapter: the adapter 8899 * @idma: the adapter IDMA Monitor state 8900 * @hz: number of ticks/second 8901 * @ticks: number of ticks since the last IDMA Monitor call 8902 */ 8903void t4_idma_monitor(struct adapter *adapter, 8904 struct sge_idma_monitor_state *idma, 8905 int hz, int ticks) 8906{ 8907 int i, idma_same_state_cnt[2]; 8908 8909 /* Read the SGE Debug Ingress DMA Same State Count registers. These 8910 * are counters inside the SGE which count up on each clock when the 8911 * SGE finds its Ingress DMA State Engines in the same states they 8912 * were in the previous clock. The counters will peg out at 8913 * 0xffffffff without wrapping around so once they pass the 1s 8914 * threshold they'll stay above that till the IDMA state changes. 8915 */ 8916 t4_write_reg(adapter, A_SGE_DEBUG_INDEX, 13); 8917 idma_same_state_cnt[0] = t4_read_reg(adapter, A_SGE_DEBUG_DATA_HIGH); 8918 idma_same_state_cnt[1] = t4_read_reg(adapter, A_SGE_DEBUG_DATA_LOW); 8919 8920 for (i = 0; i < 2; i++) { 8921 u32 debug0, debug11; 8922 8923 /* If the Ingress DMA Same State Counter ("timer") is less 8924 * than 1s, then we can reset our synthesized Stall Timer and 8925 * continue. If we have previously emitted warnings about a 8926 * potential stalled Ingress Queue, issue a note indicating 8927 * that the Ingress Queue has resumed forward progress. 8928 */ 8929 if (idma_same_state_cnt[i] < idma->idma_1s_thresh) { 8930 if (idma->idma_stalled[i] >= SGE_IDMA_WARN_THRESH*hz) 8931 CH_WARN(adapter, "SGE idma%d, queue %u, " 8932 "resumed after %d seconds\n", 8933 i, idma->idma_qid[i], 8934 idma->idma_stalled[i]/hz); 8935 idma->idma_stalled[i] = 0; 8936 continue; 8937 } 8938 8939 /* Synthesize an SGE Ingress DMA Same State Timer in the Hz 8940 * domain. The first time we get here it'll be because we 8941 * passed the 1s Threshold; each additional time it'll be 8942 * because the RX Timer Callback is being fired on its regular 8943 * schedule. 8944 * 8945 * If the stall is below our Potential Hung Ingress Queue 8946 * Warning Threshold, continue. 8947 */ 8948 if (idma->idma_stalled[i] == 0) { 8949 idma->idma_stalled[i] = hz; 8950 idma->idma_warn[i] = 0; 8951 } else { 8952 idma->idma_stalled[i] += ticks; 8953 idma->idma_warn[i] -= ticks; 8954 } 8955 8956 if (idma->idma_stalled[i] < SGE_IDMA_WARN_THRESH*hz) 8957 continue; 8958 8959 /* We'll issue a warning every SGE_IDMA_WARN_REPEAT seconds. 8960 */ 8961 if (idma->idma_warn[i] > 0) 8962 continue; 8963 idma->idma_warn[i] = SGE_IDMA_WARN_REPEAT*hz; 8964 8965 /* Read and save the SGE IDMA State and Queue ID information. 8966 * We do this every time in case it changes across time ... 8967 * can't be too careful ... 8968 */ 8969 t4_write_reg(adapter, A_SGE_DEBUG_INDEX, 0); 8970 debug0 = t4_read_reg(adapter, A_SGE_DEBUG_DATA_LOW); 8971 idma->idma_state[i] = (debug0 >> (i * 9)) & 0x3f; 8972 8973 t4_write_reg(adapter, A_SGE_DEBUG_INDEX, 11); 8974 debug11 = t4_read_reg(adapter, A_SGE_DEBUG_DATA_LOW); 8975 idma->idma_qid[i] = (debug11 >> (i * 16)) & 0xffff; 8976 8977 CH_WARN(adapter, "SGE idma%u, queue %u, potentially stuck in " 8978 " state %u for %d seconds (debug0=%#x, debug11=%#x)\n", 8979 i, idma->idma_qid[i], idma->idma_state[i], 8980 idma->idma_stalled[i]/hz, 8981 debug0, debug11); 8982 t4_sge_decode_idma_state(adapter, idma->idma_state[i]); 8983 } 8984} 8985 8986/** 8987 * t4_read_pace_tbl - read the pace table 8988 * @adap: the adapter 8989 * @pace_vals: holds the returned values 8990 * 8991 * Returns the values of TP's pace table in microseconds. 8992 */ 8993void t4_read_pace_tbl(struct adapter *adap, unsigned int pace_vals[NTX_SCHED]) 8994{ 8995 unsigned int i, v; 8996 8997 for (i = 0; i < NTX_SCHED; i++) { 8998 t4_write_reg(adap, A_TP_PACE_TABLE, 0xffff0000 + i); 8999 v = t4_read_reg(adap, A_TP_PACE_TABLE); 9000 pace_vals[i] = dack_ticks_to_usec(adap, v); 9001 } 9002} 9003 9004/** 9005 * t4_get_tx_sched - get the configuration of a Tx HW traffic scheduler 9006 * @adap: the adapter 9007 * @sched: the scheduler index 9008 * @kbps: the byte rate in Kbps 9009 * @ipg: the interpacket delay in tenths of nanoseconds 9010 * 9011 * Return the current configuration of a HW Tx scheduler. 9012 */ 9013void t4_get_tx_sched(struct adapter *adap, unsigned int sched, unsigned int *kbps, 9014 unsigned int *ipg, bool sleep_ok) 9015{ 9016 unsigned int v, addr, bpt, cpt; 9017 9018 if (kbps) { 9019 addr = A_TP_TX_MOD_Q1_Q0_RATE_LIMIT - sched / 2; 9020 t4_tp_tm_pio_read(adap, &v, 1, addr, sleep_ok); 9021 if (sched & 1) 9022 v >>= 16; 9023 bpt = (v >> 8) & 0xff; 9024 cpt = v & 0xff; 9025 if (!cpt) 9026 *kbps = 0; /* scheduler disabled */ 9027 else { 9028 v = (adap->params.vpd.cclk * 1000) / cpt; /* ticks/s */ 9029 *kbps = (v * bpt) / 125; 9030 } 9031 } 9032 if (ipg) { 9033 addr = A_TP_TX_MOD_Q1_Q0_TIMER_SEPARATOR - sched / 2; 9034 t4_tp_tm_pio_read(adap, &v, 1, addr, sleep_ok); 9035 if (sched & 1) 9036 v >>= 16; 9037 v &= 0xffff; 9038 *ipg = (10000 * v) / core_ticks_per_usec(adap); 9039 } 9040} 9041 9042/** 9043 * t4_load_cfg - download config file 9044 * @adap: the adapter 9045 * @cfg_data: the cfg text file to write 9046 * @size: text file size 9047 * 9048 * Write the supplied config text file to the card's serial flash. 9049 */ 9050int t4_load_cfg(struct adapter *adap, const u8 *cfg_data, unsigned int size) 9051{ 9052 int ret, i, n, cfg_addr; 9053 unsigned int addr; 9054 unsigned int flash_cfg_start_sec; 9055 unsigned int sf_sec_size = adap->params.sf_size / adap->params.sf_nsec; 9056 9057 cfg_addr = t4_flash_cfg_addr(adap); 9058 if (cfg_addr < 0) 9059 return cfg_addr; 9060 9061 addr = cfg_addr; 9062 flash_cfg_start_sec = addr / SF_SEC_SIZE; 9063 9064 if (size > FLASH_CFG_MAX_SIZE) { 9065 CH_ERR(adap, "cfg file too large, max is %u bytes\n", 9066 FLASH_CFG_MAX_SIZE); 9067 return -EFBIG; 9068 } 9069 9070 i = DIV_ROUND_UP(FLASH_CFG_MAX_SIZE, /* # of sectors spanned */ 9071 sf_sec_size); 9072 ret = t4_flash_erase_sectors(adap, flash_cfg_start_sec, 9073 flash_cfg_start_sec + i - 1); 9074 /* 9075 * If size == 0 then we're simply erasing the FLASH sectors associated 9076 * with the on-adapter Firmware Configuration File. 9077 */ 9078 if (ret || size == 0) 9079 goto out; 9080 9081 /* this will write to the flash up to SF_PAGE_SIZE at a time */ 9082 for (i = 0; i< size; i+= SF_PAGE_SIZE) { 9083 if ( (size - i) < SF_PAGE_SIZE) 9084 n = size - i; 9085 else 9086 n = SF_PAGE_SIZE; 9087 ret = t4_write_flash(adap, addr, n, cfg_data, 1); 9088 if (ret) 9089 goto out; 9090 9091 addr += SF_PAGE_SIZE; 9092 cfg_data += SF_PAGE_SIZE; 9093 } 9094 9095out: 9096 if (ret) 9097 CH_ERR(adap, "config file %s failed %d\n", 9098 (size == 0 ? "clear" : "download"), ret); 9099 return ret; 9100} 9101 9102/** 9103 * t5_fw_init_extern_mem - initialize the external memory 9104 * @adap: the adapter 9105 * 9106 * Initializes the external memory on T5. 9107 */ 9108int t5_fw_init_extern_mem(struct adapter *adap) 9109{ 9110 u32 params[1], val[1]; 9111 int ret; 9112 9113 if (!is_t5(adap)) 9114 return 0; 9115 9116 val[0] = 0xff; /* Initialize all MCs */ 9117 params[0] = (V_FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) | 9118 V_FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_MCINIT)); 9119 ret = t4_set_params_timeout(adap, adap->mbox, adap->pf, 0, 1, params, val, 9120 FW_CMD_MAX_TIMEOUT); 9121 9122 return ret; 9123} 9124 9125/* BIOS boot headers */ 9126typedef struct pci_expansion_rom_header { 9127 u8 signature[2]; /* ROM Signature. Should be 0xaa55 */ 9128 u8 reserved[22]; /* Reserved per processor Architecture data */ 9129 u8 pcir_offset[2]; /* Offset to PCI Data Structure */ 9130} pci_exp_rom_header_t; /* PCI_EXPANSION_ROM_HEADER */ 9131 9132/* Legacy PCI Expansion ROM Header */ 9133typedef struct legacy_pci_expansion_rom_header { 9134 u8 signature[2]; /* ROM Signature. Should be 0xaa55 */ 9135 u8 size512; /* Current Image Size in units of 512 bytes */ 9136 u8 initentry_point[4]; 9137 u8 cksum; /* Checksum computed on the entire Image */ 9138 u8 reserved[16]; /* Reserved */ 9139 u8 pcir_offset[2]; /* Offset to PCI Data Struture */ 9140} legacy_pci_exp_rom_header_t; /* LEGACY_PCI_EXPANSION_ROM_HEADER */ 9141 9142/* EFI PCI Expansion ROM Header */ 9143typedef struct efi_pci_expansion_rom_header { 9144 u8 signature[2]; // ROM signature. The value 0xaa55 9145 u8 initialization_size[2]; /* Units 512. Includes this header */ 9146 u8 efi_signature[4]; /* Signature from EFI image header. 0x0EF1 */ 9147 u8 efi_subsystem[2]; /* Subsystem value for EFI image header */ 9148 u8 efi_machine_type[2]; /* Machine type from EFI image header */ 9149 u8 compression_type[2]; /* Compression type. */ 9150 /* 9151 * Compression type definition 9152 * 0x0: uncompressed 9153 * 0x1: Compressed 9154 * 0x2-0xFFFF: Reserved 9155 */ 9156 u8 reserved[8]; /* Reserved */ 9157 u8 efi_image_header_offset[2]; /* Offset to EFI Image */ 9158 u8 pcir_offset[2]; /* Offset to PCI Data Structure */ 9159} efi_pci_exp_rom_header_t; /* EFI PCI Expansion ROM Header */ 9160 9161/* PCI Data Structure Format */ 9162typedef struct pcir_data_structure { /* PCI Data Structure */ 9163 u8 signature[4]; /* Signature. The string "PCIR" */ 9164 u8 vendor_id[2]; /* Vendor Identification */ 9165 u8 device_id[2]; /* Device Identification */ 9166 u8 vital_product[2]; /* Pointer to Vital Product Data */ 9167 u8 length[2]; /* PCIR Data Structure Length */ 9168 u8 revision; /* PCIR Data Structure Revision */ 9169 u8 class_code[3]; /* Class Code */ 9170 u8 image_length[2]; /* Image Length. Multiple of 512B */ 9171 u8 code_revision[2]; /* Revision Level of Code/Data */ 9172 u8 code_type; /* Code Type. */ 9173 /* 9174 * PCI Expansion ROM Code Types 9175 * 0x00: Intel IA-32, PC-AT compatible. Legacy 9176 * 0x01: Open Firmware standard for PCI. FCODE 9177 * 0x02: Hewlett-Packard PA RISC. HP reserved 9178 * 0x03: EFI Image. EFI 9179 * 0x04-0xFF: Reserved. 9180 */ 9181 u8 indicator; /* Indicator. Identifies the last image in the ROM */ 9182 u8 reserved[2]; /* Reserved */ 9183} pcir_data_t; /* PCI__DATA_STRUCTURE */ 9184 9185/* BOOT constants */ 9186enum { 9187 BOOT_FLASH_BOOT_ADDR = 0x0,/* start address of boot image in flash */ 9188 BOOT_SIGNATURE = 0xaa55, /* signature of BIOS boot ROM */ 9189 BOOT_SIZE_INC = 512, /* image size measured in 512B chunks */ 9190 BOOT_MIN_SIZE = sizeof(pci_exp_rom_header_t), /* basic header */ 9191 BOOT_MAX_SIZE = 1024*BOOT_SIZE_INC, /* 1 byte * length increment */ 9192 VENDOR_ID = 0x1425, /* Vendor ID */ 9193 PCIR_SIGNATURE = 0x52494350 /* PCIR signature */ 9194}; 9195 9196/* 9197 * modify_device_id - Modifies the device ID of the Boot BIOS image 9198 * @adatper: the device ID to write. 9199 * @boot_data: the boot image to modify. 9200 * 9201 * Write the supplied device ID to the boot BIOS image. 9202 */ 9203static void modify_device_id(int device_id, u8 *boot_data) 9204{ 9205 legacy_pci_exp_rom_header_t *header; 9206 pcir_data_t *pcir_header; 9207 u32 cur_header = 0; 9208 9209 /* 9210 * Loop through all chained images and change the device ID's 9211 */ 9212 while (1) { 9213 header = (legacy_pci_exp_rom_header_t *) &boot_data[cur_header]; 9214 pcir_header = (pcir_data_t *) &boot_data[cur_header + 9215 le16_to_cpu(*(u16*)header->pcir_offset)]; 9216 9217 /* 9218 * Only modify the Device ID if code type is Legacy or HP. 9219 * 0x00: Okay to modify 9220 * 0x01: FCODE. Do not be modify 9221 * 0x03: Okay to modify 9222 * 0x04-0xFF: Do not modify 9223 */ 9224 if (pcir_header->code_type == 0x00) { 9225 u8 csum = 0; 9226 int i; 9227 9228 /* 9229 * Modify Device ID to match current adatper 9230 */ 9231 *(u16*) pcir_header->device_id = device_id; 9232 9233 /* 9234 * Set checksum temporarily to 0. 9235 * We will recalculate it later. 9236 */ 9237 header->cksum = 0x0; 9238 9239 /* 9240 * Calculate and update checksum 9241 */ 9242 for (i = 0; i < (header->size512 * 512); i++) 9243 csum += (u8)boot_data[cur_header + i]; 9244 9245 /* 9246 * Invert summed value to create the checksum 9247 * Writing new checksum value directly to the boot data 9248 */ 9249 boot_data[cur_header + 7] = -csum; 9250 9251 } else if (pcir_header->code_type == 0x03) { 9252 9253 /* 9254 * Modify Device ID to match current adatper 9255 */ 9256 *(u16*) pcir_header->device_id = device_id; 9257 9258 } 9259 9260 9261 /* 9262 * Check indicator element to identify if this is the last 9263 * image in the ROM. 9264 */ 9265 if (pcir_header->indicator & 0x80) 9266 break; 9267 9268 /* 9269 * Move header pointer up to the next image in the ROM. 9270 */ 9271 cur_header += header->size512 * 512; 9272 } 9273} 9274 9275/* 9276 * t4_load_boot - download boot flash 9277 * @adapter: the adapter 9278 * @boot_data: the boot image to write 9279 * @boot_addr: offset in flash to write boot_data 9280 * @size: image size 9281 * 9282 * Write the supplied boot image to the card's serial flash. 9283 * The boot image has the following sections: a 28-byte header and the 9284 * boot image. 9285 */ 9286int t4_load_boot(struct adapter *adap, u8 *boot_data, 9287 unsigned int boot_addr, unsigned int size) 9288{ 9289 pci_exp_rom_header_t *header; 9290 int pcir_offset ; 9291 pcir_data_t *pcir_header; 9292 int ret, addr; 9293 uint16_t device_id; 9294 unsigned int i; 9295 unsigned int boot_sector = (boot_addr * 1024 ); 9296 unsigned int sf_sec_size = adap->params.sf_size / adap->params.sf_nsec; 9297 9298 /* 9299 * Make sure the boot image does not encroach on the firmware region 9300 */ 9301 if ((boot_sector + size) >> 16 > FLASH_FW_START_SEC) { 9302 CH_ERR(adap, "boot image encroaching on firmware region\n"); 9303 return -EFBIG; 9304 } 9305 9306 /* 9307 * The boot sector is comprised of the Expansion-ROM boot, iSCSI boot, 9308 * and Boot configuration data sections. These 3 boot sections span 9309 * sectors 0 to 7 in flash and live right before the FW image location. 9310 */ 9311 i = DIV_ROUND_UP(size ? size : FLASH_FW_START, 9312 sf_sec_size); 9313 ret = t4_flash_erase_sectors(adap, boot_sector >> 16, 9314 (boot_sector >> 16) + i - 1); 9315 9316 /* 9317 * If size == 0 then we're simply erasing the FLASH sectors associated 9318 * with the on-adapter option ROM file 9319 */ 9320 if (ret || (size == 0)) 9321 goto out; 9322 9323 /* Get boot header */ 9324 header = (pci_exp_rom_header_t *)boot_data; 9325 pcir_offset = le16_to_cpu(*(u16 *)header->pcir_offset); 9326 /* PCIR Data Structure */ 9327 pcir_header = (pcir_data_t *) &boot_data[pcir_offset]; 9328 9329 /* 9330 * Perform some primitive sanity testing to avoid accidentally 9331 * writing garbage over the boot sectors. We ought to check for 9332 * more but it's not worth it for now ... 9333 */ 9334 if (size < BOOT_MIN_SIZE || size > BOOT_MAX_SIZE) { 9335 CH_ERR(adap, "boot image too small/large\n"); 9336 return -EFBIG; 9337 } 9338 9339#ifndef CHELSIO_T4_DIAGS 9340 /* 9341 * Check BOOT ROM header signature 9342 */ 9343 if (le16_to_cpu(*(u16*)header->signature) != BOOT_SIGNATURE ) { 9344 CH_ERR(adap, "Boot image missing signature\n"); 9345 return -EINVAL; 9346 } 9347 9348 /* 9349 * Check PCI header signature 9350 */ 9351 if (le32_to_cpu(*(u32*)pcir_header->signature) != PCIR_SIGNATURE) { 9352 CH_ERR(adap, "PCI header missing signature\n"); 9353 return -EINVAL; 9354 } 9355 9356 /* 9357 * Check Vendor ID matches Chelsio ID 9358 */ 9359 if (le16_to_cpu(*(u16*)pcir_header->vendor_id) != VENDOR_ID) { 9360 CH_ERR(adap, "Vendor ID missing signature\n"); 9361 return -EINVAL; 9362 } 9363#endif 9364 9365 /* 9366 * Retrieve adapter's device ID 9367 */ 9368 t4_os_pci_read_cfg2(adap, PCI_DEVICE_ID, &device_id); 9369 /* Want to deal with PF 0 so I strip off PF 4 indicator */ 9370 device_id = device_id & 0xf0ff; 9371 9372 /* 9373 * Check PCIE Device ID 9374 */ 9375 if (le16_to_cpu(*(u16*)pcir_header->device_id) != device_id) { 9376 /* 9377 * Change the device ID in the Boot BIOS image to match 9378 * the Device ID of the current adapter. 9379 */ 9380 modify_device_id(device_id, boot_data); 9381 } 9382 9383 /* 9384 * Skip over the first SF_PAGE_SIZE worth of data and write it after 9385 * we finish copying the rest of the boot image. This will ensure 9386 * that the BIOS boot header will only be written if the boot image 9387 * was written in full. 9388 */ 9389 addr = boot_sector; 9390 for (size -= SF_PAGE_SIZE; size; size -= SF_PAGE_SIZE) { 9391 addr += SF_PAGE_SIZE; 9392 boot_data += SF_PAGE_SIZE; 9393 ret = t4_write_flash(adap, addr, SF_PAGE_SIZE, boot_data, 0); 9394 if (ret) 9395 goto out; 9396 } 9397 9398 ret = t4_write_flash(adap, boot_sector, SF_PAGE_SIZE, 9399 (const u8 *)header, 0); 9400 9401out: 9402 if (ret) 9403 CH_ERR(adap, "boot image download failed, error %d\n", ret); 9404 return ret; 9405} 9406 9407/* 9408 * t4_flash_bootcfg_addr - return the address of the flash optionrom configuration 9409 * @adapter: the adapter 9410 * 9411 * Return the address within the flash where the OptionROM Configuration 9412 * is stored, or an error if the device FLASH is too small to contain 9413 * a OptionROM Configuration. 9414 */ 9415static int t4_flash_bootcfg_addr(struct adapter *adapter) 9416{ 9417 /* 9418 * If the device FLASH isn't large enough to hold a Firmware 9419 * Configuration File, return an error. 9420 */ 9421 if (adapter->params.sf_size < FLASH_BOOTCFG_START + FLASH_BOOTCFG_MAX_SIZE) 9422 return -ENOSPC; 9423 9424 return FLASH_BOOTCFG_START; 9425} 9426 9427int t4_load_bootcfg(struct adapter *adap,const u8 *cfg_data, unsigned int size) 9428{ 9429 int ret, i, n, cfg_addr; 9430 unsigned int addr; 9431 unsigned int flash_cfg_start_sec; 9432 unsigned int sf_sec_size = adap->params.sf_size / adap->params.sf_nsec; 9433 9434 cfg_addr = t4_flash_bootcfg_addr(adap); 9435 if (cfg_addr < 0) 9436 return cfg_addr; 9437 9438 addr = cfg_addr; 9439 flash_cfg_start_sec = addr / SF_SEC_SIZE; 9440 9441 if (size > FLASH_BOOTCFG_MAX_SIZE) { 9442 CH_ERR(adap, "bootcfg file too large, max is %u bytes\n", 9443 FLASH_BOOTCFG_MAX_SIZE); 9444 return -EFBIG; 9445 } 9446 9447 i = DIV_ROUND_UP(FLASH_BOOTCFG_MAX_SIZE,/* # of sectors spanned */ 9448 sf_sec_size); 9449 ret = t4_flash_erase_sectors(adap, flash_cfg_start_sec, 9450 flash_cfg_start_sec + i - 1); 9451 9452 /* 9453 * If size == 0 then we're simply erasing the FLASH sectors associated 9454 * with the on-adapter OptionROM Configuration File. 9455 */ 9456 if (ret || size == 0) 9457 goto out; 9458 9459 /* this will write to the flash up to SF_PAGE_SIZE at a time */ 9460 for (i = 0; i< size; i+= SF_PAGE_SIZE) { 9461 if ( (size - i) < SF_PAGE_SIZE) 9462 n = size - i; 9463 else 9464 n = SF_PAGE_SIZE; 9465 ret = t4_write_flash(adap, addr, n, cfg_data, 0); 9466 if (ret) 9467 goto out; 9468 9469 addr += SF_PAGE_SIZE; 9470 cfg_data += SF_PAGE_SIZE; 9471 } 9472 9473out: 9474 if (ret) 9475 CH_ERR(adap, "boot config data %s failed %d\n", 9476 (size == 0 ? "clear" : "download"), ret); 9477 return ret; 9478} 9479 9480/** 9481 * t4_set_filter_mode - configure the optional components of filter tuples 9482 * @adap: the adapter 9483 * @mode_map: a bitmap selcting which optional filter components to enable 9484 * @sleep_ok: if true we may sleep while awaiting command completion 9485 * 9486 * Sets the filter mode by selecting the optional components to enable 9487 * in filter tuples. Returns 0 on success and a negative error if the 9488 * requested mode needs more bits than are available for optional 9489 * components. 9490 */ 9491int t4_set_filter_mode(struct adapter *adap, unsigned int mode_map, 9492 bool sleep_ok) 9493{ 9494 static u8 width[] = { 1, 3, 17, 17, 8, 8, 16, 9, 3, 1 }; 9495 9496 int i, nbits = 0; 9497 9498 for (i = S_FCOE; i <= S_FRAGMENTATION; i++) 9499 if (mode_map & (1 << i)) 9500 nbits += width[i]; 9501 if (nbits > FILTER_OPT_LEN) 9502 return -EINVAL; 9503 t4_tp_pio_write(adap, &mode_map, 1, A_TP_VLAN_PRI_MAP, sleep_ok); 9504 read_filter_mode_and_ingress_config(adap, sleep_ok); 9505 9506 return 0; 9507} 9508 9509/** 9510 * t4_clr_port_stats - clear port statistics 9511 * @adap: the adapter 9512 * @idx: the port index 9513 * 9514 * Clear HW statistics for the given port. 9515 */ 9516void t4_clr_port_stats(struct adapter *adap, int idx) 9517{ 9518 unsigned int i; 9519 u32 bgmap = adap2pinfo(adap, idx)->mps_bg_map; 9520 u32 port_base_addr; 9521 9522 if (is_t4(adap)) 9523 port_base_addr = PORT_BASE(idx); 9524 else 9525 port_base_addr = T5_PORT_BASE(idx); 9526 9527 for (i = A_MPS_PORT_STAT_TX_PORT_BYTES_L; 9528 i <= A_MPS_PORT_STAT_TX_PORT_PPP7_H; i += 8) 9529 t4_write_reg(adap, port_base_addr + i, 0); 9530 for (i = A_MPS_PORT_STAT_RX_PORT_BYTES_L; 9531 i <= A_MPS_PORT_STAT_RX_PORT_LESS_64B_H; i += 8) 9532 t4_write_reg(adap, port_base_addr + i, 0); 9533 for (i = 0; i < 4; i++) 9534 if (bgmap & (1 << i)) { 9535 t4_write_reg(adap, 9536 A_MPS_STAT_RX_BG_0_MAC_DROP_FRAME_L + i * 8, 0); 9537 t4_write_reg(adap, 9538 A_MPS_STAT_RX_BG_0_MAC_TRUNC_FRAME_L + i * 8, 0); 9539 } 9540} 9541 9542/** 9543 * t4_i2c_rd - read I2C data from adapter 9544 * @adap: the adapter 9545 * @port: Port number if per-port device; <0 if not 9546 * @devid: per-port device ID or absolute device ID 9547 * @offset: byte offset into device I2C space 9548 * @len: byte length of I2C space data 9549 * @buf: buffer in which to return I2C data 9550 * 9551 * Reads the I2C data from the indicated device and location. 9552 */ 9553int t4_i2c_rd(struct adapter *adap, unsigned int mbox, 9554 int port, unsigned int devid, 9555 unsigned int offset, unsigned int len, 9556 u8 *buf) 9557{ 9558 u32 ldst_addrspace; 9559 struct fw_ldst_cmd ldst; 9560 int ret; 9561 9562 if (port >= 4 || 9563 devid >= 256 || 9564 offset >= 256 || 9565 len > sizeof ldst.u.i2c.data) 9566 return -EINVAL; 9567 9568 memset(&ldst, 0, sizeof ldst); 9569 ldst_addrspace = V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_I2C); 9570 ldst.op_to_addrspace = 9571 cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 9572 F_FW_CMD_REQUEST | 9573 F_FW_CMD_READ | 9574 ldst_addrspace); 9575 ldst.cycles_to_len16 = cpu_to_be32(FW_LEN16(ldst)); 9576 ldst.u.i2c.pid = (port < 0 ? 0xff : port); 9577 ldst.u.i2c.did = devid; 9578 ldst.u.i2c.boffset = offset; 9579 ldst.u.i2c.blen = len; 9580 ret = t4_wr_mbox(adap, mbox, &ldst, sizeof ldst, &ldst); 9581 if (!ret) 9582 memcpy(buf, ldst.u.i2c.data, len); 9583 return ret; 9584} 9585 9586/** 9587 * t4_i2c_wr - write I2C data to adapter 9588 * @adap: the adapter 9589 * @port: Port number if per-port device; <0 if not 9590 * @devid: per-port device ID or absolute device ID 9591 * @offset: byte offset into device I2C space 9592 * @len: byte length of I2C space data 9593 * @buf: buffer containing new I2C data 9594 * 9595 * Write the I2C data to the indicated device and location. 9596 */ 9597int t4_i2c_wr(struct adapter *adap, unsigned int mbox, 9598 int port, unsigned int devid, 9599 unsigned int offset, unsigned int len, 9600 u8 *buf) 9601{ 9602 u32 ldst_addrspace; 9603 struct fw_ldst_cmd ldst; 9604 9605 if (port >= 4 || 9606 devid >= 256 || 9607 offset >= 256 || 9608 len > sizeof ldst.u.i2c.data) 9609 return -EINVAL; 9610 9611 memset(&ldst, 0, sizeof ldst); 9612 ldst_addrspace = V_FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_I2C); 9613 ldst.op_to_addrspace = 9614 cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 9615 F_FW_CMD_REQUEST | 9616 F_FW_CMD_WRITE | 9617 ldst_addrspace); 9618 ldst.cycles_to_len16 = cpu_to_be32(FW_LEN16(ldst)); 9619 ldst.u.i2c.pid = (port < 0 ? 0xff : port); 9620 ldst.u.i2c.did = devid; 9621 ldst.u.i2c.boffset = offset; 9622 ldst.u.i2c.blen = len; 9623 memcpy(ldst.u.i2c.data, buf, len); 9624 return t4_wr_mbox(adap, mbox, &ldst, sizeof ldst, &ldst); 9625} 9626 9627/** 9628 * t4_sge_ctxt_rd - read an SGE context through FW 9629 * @adap: the adapter 9630 * @mbox: mailbox to use for the FW command 9631 * @cid: the context id 9632 * @ctype: the context type 9633 * @data: where to store the context data 9634 * 9635 * Issues a FW command through the given mailbox to read an SGE context. 9636 */ 9637int t4_sge_ctxt_rd(struct adapter *adap, unsigned int mbox, unsigned int cid, 9638 enum ctxt_type ctype, u32 *data) 9639{ 9640 int ret; 9641 struct fw_ldst_cmd c; 9642 9643 if (ctype == CTXT_EGRESS) 9644 ret = FW_LDST_ADDRSPC_SGE_EGRC; 9645 else if (ctype == CTXT_INGRESS) 9646 ret = FW_LDST_ADDRSPC_SGE_INGC; 9647 else if (ctype == CTXT_FLM) 9648 ret = FW_LDST_ADDRSPC_SGE_FLMC; 9649 else 9650 ret = FW_LDST_ADDRSPC_SGE_CONMC; 9651 9652 memset(&c, 0, sizeof(c)); 9653 c.op_to_addrspace = cpu_to_be32(V_FW_CMD_OP(FW_LDST_CMD) | 9654 F_FW_CMD_REQUEST | F_FW_CMD_READ | 9655 V_FW_LDST_CMD_ADDRSPACE(ret)); 9656 c.cycles_to_len16 = cpu_to_be32(FW_LEN16(c)); 9657 c.u.idctxt.physid = cpu_to_be32(cid); 9658 9659 ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); 9660 if (ret == 0) { 9661 data[0] = be32_to_cpu(c.u.idctxt.ctxt_data0); 9662 data[1] = be32_to_cpu(c.u.idctxt.ctxt_data1); 9663 data[2] = be32_to_cpu(c.u.idctxt.ctxt_data2); 9664 data[3] = be32_to_cpu(c.u.idctxt.ctxt_data3); 9665 data[4] = be32_to_cpu(c.u.idctxt.ctxt_data4); 9666 data[5] = be32_to_cpu(c.u.idctxt.ctxt_data5); 9667 } 9668 return ret; 9669} 9670 9671/** 9672 * t4_sge_ctxt_rd_bd - read an SGE context bypassing FW 9673 * @adap: the adapter 9674 * @cid: the context id 9675 * @ctype: the context type 9676 * @data: where to store the context data 9677 * 9678 * Reads an SGE context directly, bypassing FW. This is only for 9679 * debugging when FW is unavailable. 9680 */ 9681int t4_sge_ctxt_rd_bd(struct adapter *adap, unsigned int cid, enum ctxt_type ctype, 9682 u32 *data) 9683{ 9684 int i, ret; 9685 9686 t4_write_reg(adap, A_SGE_CTXT_CMD, V_CTXTQID(cid) | V_CTXTTYPE(ctype)); 9687 ret = t4_wait_op_done(adap, A_SGE_CTXT_CMD, F_BUSY, 0, 3, 1); 9688 if (!ret) 9689 for (i = A_SGE_CTXT_DATA0; i <= A_SGE_CTXT_DATA5; i += 4) 9690 *data++ = t4_read_reg(adap, i); 9691 return ret; 9692} 9693 9694int t4_sched_config(struct adapter *adapter, int type, int minmaxen, 9695 int sleep_ok) 9696{ 9697 struct fw_sched_cmd cmd; 9698 9699 memset(&cmd, 0, sizeof(cmd)); 9700 cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_SCHED_CMD) | 9701 F_FW_CMD_REQUEST | 9702 F_FW_CMD_WRITE); 9703 cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); 9704 9705 cmd.u.config.sc = FW_SCHED_SC_CONFIG; 9706 cmd.u.config.type = type; 9707 cmd.u.config.minmaxen = minmaxen; 9708 9709 return t4_wr_mbox_meat(adapter,adapter->mbox, &cmd, sizeof(cmd), 9710 NULL, sleep_ok); 9711} 9712 9713int t4_sched_params(struct adapter *adapter, int type, int level, int mode, 9714 int rateunit, int ratemode, int channel, int cl, 9715 int minrate, int maxrate, int weight, int pktsize, 9716 int sleep_ok) 9717{ 9718 struct fw_sched_cmd cmd; 9719 9720 memset(&cmd, 0, sizeof(cmd)); 9721 cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_SCHED_CMD) | 9722 F_FW_CMD_REQUEST | 9723 F_FW_CMD_WRITE); 9724 cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); 9725 9726 cmd.u.params.sc = FW_SCHED_SC_PARAMS; 9727 cmd.u.params.type = type; 9728 cmd.u.params.level = level; 9729 cmd.u.params.mode = mode; 9730 cmd.u.params.ch = channel; 9731 cmd.u.params.cl = cl; 9732 cmd.u.params.unit = rateunit; 9733 cmd.u.params.rate = ratemode; 9734 cmd.u.params.min = cpu_to_be32(minrate); 9735 cmd.u.params.max = cpu_to_be32(maxrate); 9736 cmd.u.params.weight = cpu_to_be16(weight); 9737 cmd.u.params.pktsize = cpu_to_be16(pktsize); 9738 9739 return t4_wr_mbox_meat(adapter,adapter->mbox, &cmd, sizeof(cmd), 9740 NULL, sleep_ok); 9741} 9742 9743int t4_sched_params_ch_rl(struct adapter *adapter, int channel, int ratemode, 9744 unsigned int maxrate, int sleep_ok) 9745{ 9746 struct fw_sched_cmd cmd; 9747 9748 memset(&cmd, 0, sizeof(cmd)); 9749 cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_SCHED_CMD) | 9750 F_FW_CMD_REQUEST | 9751 F_FW_CMD_WRITE); 9752 cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); 9753 9754 cmd.u.params.sc = FW_SCHED_SC_PARAMS; 9755 cmd.u.params.type = FW_SCHED_TYPE_PKTSCHED; 9756 cmd.u.params.level = FW_SCHED_PARAMS_LEVEL_CH_RL; 9757 cmd.u.params.ch = channel; 9758 cmd.u.params.rate = ratemode; /* REL or ABS */ 9759 cmd.u.params.max = cpu_to_be32(maxrate);/* % or kbps */ 9760 9761 return t4_wr_mbox_meat(adapter,adapter->mbox, &cmd, sizeof(cmd), 9762 NULL, sleep_ok); 9763} 9764 9765int t4_sched_params_cl_wrr(struct adapter *adapter, int channel, int cl, 9766 int weight, int sleep_ok) 9767{ 9768 struct fw_sched_cmd cmd; 9769 9770 if (weight < 0 || weight > 100) 9771 return -EINVAL; 9772 9773 memset(&cmd, 0, sizeof(cmd)); 9774 cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_SCHED_CMD) | 9775 F_FW_CMD_REQUEST | 9776 F_FW_CMD_WRITE); 9777 cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); 9778 9779 cmd.u.params.sc = FW_SCHED_SC_PARAMS; 9780 cmd.u.params.type = FW_SCHED_TYPE_PKTSCHED; 9781 cmd.u.params.level = FW_SCHED_PARAMS_LEVEL_CL_WRR; 9782 cmd.u.params.ch = channel; 9783 cmd.u.params.cl = cl; 9784 cmd.u.params.weight = cpu_to_be16(weight); 9785 9786 return t4_wr_mbox_meat(adapter,adapter->mbox, &cmd, sizeof(cmd), 9787 NULL, sleep_ok); 9788} 9789 9790int t4_sched_params_cl_rl_kbps(struct adapter *adapter, int channel, int cl, 9791 int mode, unsigned int maxrate, int pktsize, int sleep_ok) 9792{ 9793 struct fw_sched_cmd cmd; 9794 9795 memset(&cmd, 0, sizeof(cmd)); 9796 cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_SCHED_CMD) | 9797 F_FW_CMD_REQUEST | 9798 F_FW_CMD_WRITE); 9799 cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); 9800 9801 cmd.u.params.sc = FW_SCHED_SC_PARAMS; 9802 cmd.u.params.type = FW_SCHED_TYPE_PKTSCHED; 9803 cmd.u.params.level = FW_SCHED_PARAMS_LEVEL_CL_RL; 9804 cmd.u.params.mode = mode; 9805 cmd.u.params.ch = channel; 9806 cmd.u.params.cl = cl; 9807 cmd.u.params.unit = FW_SCHED_PARAMS_UNIT_BITRATE; 9808 cmd.u.params.rate = FW_SCHED_PARAMS_RATE_ABS; 9809 cmd.u.params.max = cpu_to_be32(maxrate); 9810 cmd.u.params.pktsize = cpu_to_be16(pktsize); 9811 9812 return t4_wr_mbox_meat(adapter,adapter->mbox, &cmd, sizeof(cmd), 9813 NULL, sleep_ok); 9814} 9815 9816/* 9817 * t4_config_watchdog - configure (enable/disable) a watchdog timer 9818 * @adapter: the adapter 9819 * @mbox: mailbox to use for the FW command 9820 * @pf: the PF owning the queue 9821 * @vf: the VF owning the queue 9822 * @timeout: watchdog timeout in ms 9823 * @action: watchdog timer / action 9824 * 9825 * There are separate watchdog timers for each possible watchdog 9826 * action. Configure one of the watchdog timers by setting a non-zero 9827 * timeout. Disable a watchdog timer by using a timeout of zero. 9828 */ 9829int t4_config_watchdog(struct adapter *adapter, unsigned int mbox, 9830 unsigned int pf, unsigned int vf, 9831 unsigned int timeout, unsigned int action) 9832{ 9833 struct fw_watchdog_cmd wdog; 9834 unsigned int ticks; 9835 9836 /* 9837 * The watchdog command expects a timeout in units of 10ms so we need 9838 * to convert it here (via rounding) and force a minimum of one 10ms 9839 * "tick" if the timeout is non-zero but the conversion results in 0 9840 * ticks. 9841 */ 9842 ticks = (timeout + 5)/10; 9843 if (timeout && !ticks) 9844 ticks = 1; 9845 9846 memset(&wdog, 0, sizeof wdog); 9847 wdog.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_WATCHDOG_CMD) | 9848 F_FW_CMD_REQUEST | 9849 F_FW_CMD_WRITE | 9850 V_FW_PARAMS_CMD_PFN(pf) | 9851 V_FW_PARAMS_CMD_VFN(vf)); 9852 wdog.retval_len16 = cpu_to_be32(FW_LEN16(wdog)); 9853 wdog.timeout = cpu_to_be32(ticks); 9854 wdog.action = cpu_to_be32(action); 9855 9856 return t4_wr_mbox(adapter, mbox, &wdog, sizeof wdog, NULL); 9857} 9858 9859int t4_get_devlog_level(struct adapter *adapter, unsigned int *level) 9860{ 9861 struct fw_devlog_cmd devlog_cmd; 9862 int ret; 9863 9864 memset(&devlog_cmd, 0, sizeof(devlog_cmd)); 9865 devlog_cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_DEVLOG_CMD) | 9866 F_FW_CMD_REQUEST | F_FW_CMD_READ); 9867 devlog_cmd.retval_len16 = cpu_to_be32(FW_LEN16(devlog_cmd)); 9868 ret = t4_wr_mbox(adapter, adapter->mbox, &devlog_cmd, 9869 sizeof(devlog_cmd), &devlog_cmd); 9870 if (ret) 9871 return ret; 9872 9873 *level = devlog_cmd.level; 9874 return 0; 9875} 9876 9877int t4_set_devlog_level(struct adapter *adapter, unsigned int level) 9878{ 9879 struct fw_devlog_cmd devlog_cmd; 9880 9881 memset(&devlog_cmd, 0, sizeof(devlog_cmd)); 9882 devlog_cmd.op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_DEVLOG_CMD) | 9883 F_FW_CMD_REQUEST | 9884 F_FW_CMD_WRITE); 9885 devlog_cmd.level = level; 9886 devlog_cmd.retval_len16 = cpu_to_be32(FW_LEN16(devlog_cmd)); 9887 return t4_wr_mbox(adapter, adapter->mbox, &devlog_cmd, 9888 sizeof(devlog_cmd), &devlog_cmd); 9889} 9890