1# $FreeBSD$
2#
3# Example configuration file for bsnmpd(1).
4#
5
6#
7# Set some common variables
8#
9location := "Room 200"
10contact := "sysmeister@example.com"
11system := 1	# FreeBSD
12traphost := localhost
13trapport := 162
14
15#
16# Set the SNMP engine ID.
17#
18# The snmpEngineID object required from the SNMPv3 Framework. If not explicitly set via
19# this configuration file, an ID is assigned based on the value of the
20# kern.hostid variable
21# engine := 0x80:0x10:0x08:0x10:0x80:0x25
22# snmpEngineID = $(engine)
23
24# Change this!
25read := "public"
26# Uncomment begemotSnmpdCommunityString.0.2 below that sets the community
27# string to enable write access.
28write := "geheim"
29trap := "mytrap"
30
31#
32# Declarations for SNMP-USER-BASED-SM-MIB authentication and privacy options
33#
34
35NoAuthProtocol		:= 1.3.6.1.6.3.10.1.1.1
36HMACMD5AuthProtocol	:= 1.3.6.1.6.3.10.1.1.2
37HMACSHAAuthProtocol	:= 1.3.6.1.6.3.10.1.1.3
38NoPrivProtocol		:= 1.3.6.1.6.3.10.1.2.1
39DESPrivProtocol		:= 1.3.6.1.6.3.10.1.2.2
40AesCfb128Protocol	:= 1.3.6.1.6.3.10.1.2.4
41
42#
43# Enumerations from SNMP-FRAMEWORK-MIB
44#
45
46# Security models
47securityModelAny	:= 0
48securityModelSNMPv1	:= 1
49securityModelSNMPv2c	:= 2
50securityModelUSM	:= 3
51
52# Message Processing models
53MPmodelSNMPv1		:= 0
54MPmodelSNMPv2c		:= 1
55MPmodelSNMPv3		:= 3
56
57# Security levels
58noAuthNoPriv := 1
59authNoPriv := 2
60authPriv := 3
61
62
63# SNMPv3 USM User definition
64#
65# The localized hex password for a user may be obtained by setting SNMPUSER, SNMPPASSWD,
66# SNMPAUTH and SNMPPRIV environment variables to the desired parameters and invoking
67# 'bsnmpget -v 3 -D -K -o verbose' against the running bsnmpd(1). For other
68# usages refer to the bsnmpget(1) manual page. The following lines define a user "bsnmp"
69# with a private password "bsnmptest", localized for the above engine ID.
70#
71#user1 := "bsnmp"
72#user1passwd := 0x22:0x98:0x1a:0x6e:0x39:0x93:0x16:0x5e:0x6a:0x21:0x1b:0xd8:0xa9:0x81:0x31:0x05:0x16:0x33:0x38:0x60
73
74#
75# Configuration
76#
77%snmpd
78begemotSnmpdDebugDumpPdus	= 2
79begemotSnmpdDebugSyslogPri	= 7
80
81#
82# Set the read and write communities.
83#
84# The default value of the community strings is NULL (note, that this is
85# different from the empty string). This disables both read and write access.
86# To enable read access only the read community string must be set. Setting
87# the write community string enables both read and write access with that
88# string.
89#
90# Be sure to understand the security implications of SNMPv2 - the community
91# strings are readable on the wire!
92#
93begemotSnmpdCommunityString.0.1	= $(read)
94# begemotSnmpdCommunityString.0.2	= $(write)
95begemotSnmpdCommunityDisable	= 1
96
97# open standard SNMP ports
98begemotSnmpdPortStatus.0.0.0.0.161 = 1
99
100# open a unix domain socket
101begemotSnmpdLocalPortStatus."/var/run/snmpd.sock" = 1
102begemotSnmpdLocalPortType."/var/run/snmpd.sock" = 4
103
104# send traps to the traphost
105begemotTrapSinkStatus.[$(traphost)].$(trapport) = 4
106begemotTrapSinkVersion.[$(traphost)].$(trapport) = 2
107begemotTrapSinkComm.[$(traphost)].$(trapport) = $(trap)
108
109sysContact	= $(contact)
110sysLocation	= $(location)
111sysObjectId 	= 1.3.6.1.4.1.12325.1.1.2.1.$(system)
112
113snmpEnableAuthenTraps = 2
114
115#
116# SNMPv3 User-based security module - must be loaded for SNMPv3 USM
117#
118#begemotSnmpdModulePath."usm"	= "/usr/lib/snmp_usm.so"
119
120#
121# SNMPv3 USM User definition.
122#
123
124#%usm
125
126#
127# The following block creates a user with name "bsnmp" and sets privacy
128# and encryption options to SHA256 message digests and AES encryption
129# for this user.
130# 
131# usmUserStatus.$(engine).$(user1) = 5
132# usmUserAuthProtocol.$(engine).$(user1) = $(HMACSHAAuthProtocol)
133# usmUserAuthKeyChange.$(engine).$(user1) = $(user1passwd)
134# usmUserPrivProtocol.$(engine).$(user1) = $(AesCfb128Protocol)
135# usmUserPrivKeyChange.$(engine).$(user1) = $(user1passwd)
136# usmUserStatus.$(engine).$(user1) = 1
137#
138
139#
140# The following block creates a user with name "public" with no authentication
141# or encryption options.
142#
143# usmUserStatus.$(engine).$(read) = 5
144# usmUserAuthProtocol.$(engine).$(read) = $(NoAuthProtocol)
145# usmUserPrivProtocol.$(engine).$(read) = $(NoPrivProtocol)
146# usmUserStatus.$(engine).$(read) = 1
147#
148
149#
150# SNMPv3 View-based Access Control module
151#
152#begemotSnmpdModulePath."vacm"	= "/usr/lib/snmp_vacm.so"
153
154#
155# Definition of view-based access control entries.
156#
157#%vacm
158
159# Definition of a SNMPv1 group
160# vacmSecurityToGroupStatus.$(securityModelSNMPv1).$(read) = 4
161# vacmGroupName.$(securityModelSNMPv1).$(read) = $(read)
162
163# Definition of SNMPv2 group
164# vacmSecurityToGroupStatus.$(securityModelSNMPv2c).$(write) = 4
165# vacmGroupName.$(securityModelSNMPv2c).$(write) = $(write)
166
167# Definition of SNMPv3 group with users "bsnmp" and "public"
168# vacmSecurityToGroupStatus.$(securityModelUSM).$(user1) = 4
169# vacmGroupName.$(securityModelUSM).$(user1) = $(write)
170# vacmSecurityToGroupStatus.$(securityModelUSM).$(read) = 4
171# vacmGroupName.$(securityModelUSM).$(read) = $(write)
172
173# 
174# The OID of the .iso.org.dod.internet subtree
175#
176# internetoid := 1.3.6.1
177# internetoidlen := 4
178
179#
180# Definitions of two views
181#
182# vacmViewTreeFamilyStatus."internet".$(internetoidlen).$(internetoid) = 4
183# vacmViewTreeFamilyStatus."restricted".$(internetoidlen).$(internetoid) = 4
184
185#
186# Access control
187#
188
189#
190# Read-only access for SNMPv1 users
191#
192# vacmAccessStatus.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = 4
193# vacmAccessReadViewName.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = "internet"
194
195#
196# Read-write access for SNMPv2 users 
197#
198# vacmAccessStatus.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = 4
199# vacmAccessReadViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet"
200# vacmAccessWriteViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet"
201
202#
203# Read-write-notify access for SNMPv3 USM users with noAuthNoPriv
204#
205# vacmAccessStatus.$(write)."".3.$(noAuthNoPriv) = 4
206# vacmAccessReadViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet"
207# vacmAccessWriteViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet"
208# vacmAccessNotifyViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet"
209
210#
211#Read-write-notify access to restricted for SNMPv3 USM users with authPriv
212#
213# vacmAccessStatus.$(write)."".3.$(authPriv) = 4
214# vacmAccessReadViewName.$(write)."".3.$(authPriv) = "restricted"
215# vacmAccessWriteViewName.$(write)."".3.$(authPriv) = "restricted"
216# vacmAccessNotifyViewName.$(write)."".3.$(authPriv) = "restricted"
217
218#
219# SNMPv3 Notification Targets
220#
221# begemotSnmpdModulePath."target"	= "/usr/lib/snmp_target.so"
222
223#%target
224# Send notifications to target tag "test"
225# tag		:= "test"
226# snmpNotifyRowStatus.$(tag) = 4
227# snmpNotifyTag.$(tag) = $(tag)
228
229# tagremote		:= "testremote"
230# snmpNotifyRowStatus.$(tagremote) = 4
231# snmpNotifyTag.$(tagremote) = $(tagremote)
232
233#
234# Specify the target parameters for the notifications - send with the credentials
235# of user "bsnmp"
236#
237# snmpTargetParamsRowStatus.$(tag) = 5
238# snmpTargetParamsMPModel.$(tag) = $(MPmodelSNMPv3)
239# snmpTargetParamsSecurityModel.$(tag) = $(securityModelUSM)
240# snmpTargetParamsSecurityName.$(tag) = $(user1)
241# snmpTargetParamsSecurityLevel.$(tag) = $(authPriv)
242# snmpTargetParamsRowStatus.$(tag) = 1
243
244#
245# Define the notifications' target address - port 162 on localhost
246#
247# snmpTargetAddrRowStatus.$(tag) = 5
248# snmpTargetAddrTAddress.$(tag) = 0x7f:0x0:0x0:0x1:0x0:0xa2
249# snmpTargetAddrTagList.$(tag) = "test notification"
250# snmpTargetAddrParams.$(tag) = $(tag)
251# snmpTargetAddrRowStatus.$(tag) = 1
252
253#
254# Define the notifications' target address - port 162 on 10.0.0.1
255#
256# snmpTargetAddrRowStatus.$(tagremote) = 5
257# snmpTargetAddrTAddress.$(tagremote) = 0x0a:0x00:0x00:0x1:0x0:0xa2
258# snmpTargetAddrTagList.$(tagremote) = $(tagremote)
259# snmpTargetAddrParams.$(tagremote) = $(tag)
260# snmpTargetAddrRowStatus.$(tagremote) = 1
261
262#
263# Load MIB-2 module
264#
265begemotSnmpdModulePath."mibII"	= "/usr/lib/snmp_mibII.so"
266
267# Force a polling rate for the 64-bit interface counters in case
268# the automatic computation is wrong (which may be the case if an interface
269# announces the wrong bit rate via its MIB).
270#%mibII
271#begemotIfForcePoll = 2000
272
273
274# Netgraph module
275#
276#begemotSnmpdModulePath."netgraph" = "/usr/lib/snmp_netgraph.so"
277#
278#%netgraph
279#begemotNgControlNodeName = "snmpd"
280
281#
282# pf(4) module
283#
284#begemotSnmpdModulePath."pf"	= "/usr/lib/snmp_pf.so"
285
286#
287# Host resources module
288#  This requires the mibII module.
289#
290#begemotSnmpdModulePath."hostres" = "/usr/lib/snmp_hostres.so"
291
292#
293# Bridge module
294#  This requires the mibII module.
295#
296#begemotSnmpdModulePath."bridge" = "/usr/lib/snmp_bridge.so"
297
298#
299# Wireless module
300#  This requires the mibII module.
301#
302#begemotSnmpdModulePath."wlan" = "/usr/lib/snmp_wlan.so"
303