1# $FreeBSD$
2#	from: @(#)gettytab	5.14 (Berkeley) 3/27/91
3#
4# Most of the table entries here are just copies of the old getty table,
5# it is by no means certain, or even likely, that any of them are optimal
6# for any purpose whatever.  Nor is it likely that more than a couple are
7# even correct.
8#
9# The default gettytab entry, used to set defaults for all other
10# entries, and in cases where getty is called with no table name.
11#
12# cb, ce and ck are desirable on most crt's.  The non-crt entries need to
13# be changed to turn them off (:cb@:ce@:ck@:).
14#
15# lc should always be on; it's a remainder of some stone age when there
16# have been terminals around not being able of handling lower-case
17# characters. Those terminals aren't supported any longer, but getty is
18# `smart' about them by default.
19#
20# Parity defaults to even, but the Pc entry and all the `std' entries
21# specify no parity.   The different parities are:
22#     (none): same as ep for getty.  login will use terminal as is.
23#     ep:     getty will use raw mode (cs8 -parenb) (unless rw is set) and
24#             fake parity.  login will use even parity (cs7 parenb -parodd).
25#     op:     same as ep except odd parity (cs7 parenb parodd) for login.
26#             getty will fake odd parity as well.
27#     ap:     same as ep except -inpck instead of inpck for login.
28#             ap overrides op and ep.
29#     np:     1. don't fake parity in getty.  The fake parity garbles
30#                characters on non-terminals (like pccons) that don't
31#                support parity.  It would probably better for getty not to
32#                try to fake parity.  It could just use cbreak mode so as
33#                not to force cs8 and let the hardware handle the parity.
34#                login has to be rely on the hardware anyway.
35#             2. set cs8 -parenb -istrip -inpck.
36#     ep:op:  same as ap.
37#
38default:\
39	:cb:ce:ck:lc:fd#1000:im=\r\n%s/%m (%h) (%t)\r\n\r\n:sp#1200:\
40	:if=/etc/issue:
41
42#
43# Fixed speed entries
44#
45#	The "std.NNN" names are known to the special case
46#	portselector code in getty, however they can
47#	be assigned to any table desired.
48#	The "NNN-baud" names are known to the special case
49#	autobaud code in getty, and likewise can
50#	be assigned to any table desired (hopefully the same speed).
51#
52a|std.110|110-baud:\
53	:np:nd#1:cd#1:uc:sp#110:
54b|std.134|134.5-baud:\
55	:np:nd#1:cd#2:ff#1:td#1:sp#134:ht:nl:
561|std.150|150-baud:\
57	:np:nd#1:cd#2:td#1:fd#1:sp#150:ht:nl:lm=\E\72\6\6\17login\72 :
58c|std.300|300-baud:\
59	:np:nd#1:cd#1:sp#300:
60d|std.600|600-baud:\
61	:np:nd#1:cd#1:sp#600:
62f|std.1200|1200-baud:\
63	:np:fd#1:sp#1200:
646|std.2400|2400-baud:\
65	:np:sp#2400:
667|std.4800|4800-baud:\
67	:np:sp#4800:
682|std.9600|9600-baud:\
69	:np:sp#9600:
70g|std.19200|19200-baud:\
71	:np:sp#19200:
72std.38400|38400-baud:\
73	:np:sp#38400:
74std.57600|57600-baud:\
75	:np:sp#57600:
76std.115200|115200-baud:\
77	:np:sp#115200:
78std.230400|230400-baud:\
79	:np:sp#230400:
80
81#
82# Entry specifying explicit device settings.  See termios(4) and
83# /usr/include/termios.h, too.  The entry forces the tty into
84# CLOCAL mode (so no DCD is required), and uses Xon/Xoff flow control.
85#
86# cflags: CLOCAL | HUPCL | CREAD | CS8
87# oflags: OPOST | ONLCR | OXTABS
88# iflags: IXOFF | IXON | ICRNL | IGNPAR
89# lflags: IEXTEN | ICANON | ISIG | ECHOCTL | ECHO | ECHOK | ECHOE | ECHOKE
90#
91# The `0' flags don't have input enabled.  The `1' flags don't echo.
92# (Echoing is done inside getty itself.)
93#
94local.9600|CLOCAL tty @ 9600 Bd:\
95	:c0#0x0000c300:c1#0x0000cb00:c2#0x0000cb00:\
96	:o0#0x00000007:o1#0x00000002:o2#0x00000007:\
97	:i0#0x00000704:i1#0x00000000:i2#0x00000704:\
98	:l0#0x000005cf:l1#0x00000000:l2#0x000005cf:\
99	:sp#9600:np:
100
101#
102# Dial in rotary tables, speed selection via 'break'
103#
1040|d300|Dial-300:\
105	:nx=d1200:cd#2:sp#300:
106d1200|Dial-1200:\
107	:nx=d150:fd#1:sp#1200:
108d150|Dial-150:\
109	:nx=d110:lm@:tc=150-baud:
110d110|Dial-110:\
111	:nx=d300:tc=300-baud:
112
113#
114# Fast dialup terminals, 2400/1200/300 rotary (can start either way)
115#
116D2400|d2400|Fast-Dial-2400:\
117	:nx=D1200:tc=2400-baud:
1183|D1200|Fast-Dial-1200:\
119	:nx=D300:tc=1200-baud:
1205|D300|Fast-Dial-300:\
121	:nx=D2400:tc=300-baud:
122
123#
124#telebit (19200)
125#
126t19200:\
127	:nx=t2400:tc=19200-baud:
128t2400:\
129	:nx=t1200:tc=2400-baud:
130t1200:\
131	:nx=t19200:tc=1200-baud:
132
133#
134#telebit (9600)
135#
136t9600:\
137	:nx=t2400a:tc=9600-baud:
138t2400a:\
139	:nx=t1200a:tc=2400-baud:
140t1200a:\
141	:nx=t9600:tc=1200-baud:
142
143#
144# Odd special case terminals
145#
146-|tty33|asr33|Pity the poor user of this beast:\
147	:tc=110-baud:
148
1494|Console|Console Decwriter II:\
150	:nd@:cd@:rw:tc=300-baud:
151
152e|Console-1200|Console Decwriter III:\
153	:fd@:nd@:cd@:rw:tc=1200-baud:
154
155i|Interdata console:\
156	:uc:sp#0:
157
158l|lsi chess terminal:\
159	:sp#300:
160
161X|Xwindow|X window system:\
162	:fd@:nd@:cd@:rw:sp#9600:
163
164P|Pc|Pc console:\
165	:ht:np:sp#9600:
166
167#
168# Weirdo special case for fast crt's with hardcopy devices
169#
1708|T9600|CRT with hardcopy:\
171	:nx=T300:tc=9600-baud:
1729|T300|CRT with hardcopy (300):\
173	:nx=T9600:tc=300-baud:
174
175#
176# Plugboard, and misc other terminals
177#
178plug-9600|Plugboard-9600:\
179	:pf#1:tc=9600-baud:
180p|P9600|Plugboard-9600-rotary:\
181	:pf#1:nx=P300:tc=9600-baud:
182q|P300|Plugboard-300:\
183	:pf#1:nx=P1200:tc=300-baud:
184r|P1200|Plugboard-1200:\
185	:pf#1:nx=P9600:tc=1200-baud:
186
187#
188# XXXX Port selector
189#
190s|DSW|Port Selector:\
191	:ps:sp#2400:
192
193#
194# Auto-baud speed detect entry for Micom 600.
195# Special code in getty will switch this out
196# to one of the NNN-baud entries.
197#
198A|Auto-baud:\
199	:ab:sp#2400:f0#040:
200
201#
202# autologin - automatically log in as root
203#
204
205autologin|al.9600:\
206	:al=root:tc=std.9600:
207al.19200:\
208	:al=root:tc=std.19200:
209al.38400:\
210	:al=root:tc=std.38400:
211al.57600:\
212	:al=root:tc=std.57600:
213al.115200:\
214	:al=root:tc=std.115200:
215al.230400:\
216	:al=root:tc=std.230400:
217
218#
219# Entries for 3-wire serial terminals.  These don't supply carrier, so
220# clocal needs to be set, and crtscts needs to be unset.
221#
2223wire.9600|9600-3wire:\
223	:np:nc:sp#9600:
2243wire.19200|19200-3wire:\
225	:np:nc:sp#19200:
2263wire.38400|38400-3wire:\
227	:np:nc:sp#38400:
2283wire.57600|57600-3wire:\
229	:np:nc:sp#57600:
2303wire.115200|115200-3wire:\
231	:np:nc:sp#115200:
2323wire.230400|230400-3wire:\
233	:np:nc:sp#230400:
234