1/*- 2 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer, 10 * without modification. 11 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 12 * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any 13 * redistribution must be conditioned upon including a substantially 14 * similar Disclaimer requirement for further binary redistribution. 15 * 16 * NO WARRANTY 17 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 18 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 19 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY 20 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL 21 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, 22 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 23 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 24 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER 25 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 26 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 27 * THE POSSIBILITY OF SUCH DAMAGES. 28 */ 29 30#include <sys/cdefs.h> 31__FBSDID("$FreeBSD$"); 32 33/* 34 * Driver for the Atheros Wireless LAN controller. 35 * 36 * This software is derived from work of Atsushi Onoe; his contribution 37 * is greatly appreciated. 38 */ 39 40#include "opt_inet.h" 41#include "opt_ath.h" 42/* 43 * This is needed for register operations which are performed 44 * by the driver - eg, calls to ath_hal_gettsf32(). 45 */ 46#include "opt_ah.h" 47#include "opt_wlan.h" 48 49#include <sys/param.h> 50#include <sys/systm.h> 51#include <sys/sysctl.h> 52#include <sys/mbuf.h> 53#include <sys/malloc.h> 54#include <sys/lock.h> 55#include <sys/mutex.h> 56#include <sys/kernel.h> 57#include <sys/socket.h> 58#include <sys/sockio.h> 59#include <sys/errno.h> 60#include <sys/callout.h> 61#include <sys/bus.h> 62#include <sys/endian.h> 63#include <sys/kthread.h> 64#include <sys/taskqueue.h> 65#include <sys/priv.h> 66#include <sys/module.h> 67#include <sys/ktr.h> 68#include <sys/smp.h> /* for mp_ncpus */ 69 70#include <machine/bus.h> 71 72#include <net/if.h> 73#include <net/if_dl.h> 74#include <net/if_media.h> 75#include <net/if_types.h> 76#include <net/if_arp.h> 77#include <net/ethernet.h> 78#include <net/if_llc.h> 79 80#include <net80211/ieee80211_var.h> 81#include <net80211/ieee80211_regdomain.h> 82#ifdef IEEE80211_SUPPORT_SUPERG 83#include <net80211/ieee80211_superg.h> 84#endif 85#ifdef IEEE80211_SUPPORT_TDMA 86#include <net80211/ieee80211_tdma.h> 87#endif 88 89#include <net/bpf.h> 90 91#ifdef INET 92#include <netinet/in.h> 93#include <netinet/if_ether.h> 94#endif 95 96#include <dev/ath/if_athvar.h> 97#include <dev/ath/ath_hal/ah_devid.h> /* XXX for softled */ 98#include <dev/ath/ath_hal/ah_diagcodes.h> 99 100#include <dev/ath/if_ath_debug.h> 101#include <dev/ath/if_ath_misc.h> 102 103#include <dev/ath/if_ath_led.h> 104 105/* 106 * Software LED driver routines. 107 */ 108 109/* 110 * XXX TODO: move the LED sysctls here. 111 */ 112 113 114/* 115 * Configure the hardware for software and LED blinking. 116 * The user may choose to configure part of each, depending upon the 117 * NIC being used. 118 * 119 * This requires the configuration to be set before this function 120 * is called. 121 */ 122void 123ath_led_config(struct ath_softc *sc) 124{ 125 /* Software LED blinking - GPIO controlled LED */ 126 if (sc->sc_softled) { 127 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_ledpin, 128 HAL_GPIO_OUTPUT_MUX_AS_OUTPUT); 129 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, !sc->sc_ledon); 130 } 131 132 /* Hardware LED blinking - MAC controlled LED */ 133 if (sc->sc_hardled) { 134 /* 135 * Only enable each LED if required. 136 * 137 * Some NICs only have one LED connected; others may 138 * have GPIO1/GPIO2 connected to other hardware. 139 */ 140 if (sc->sc_led_pwr_pin > 0) 141 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_led_pwr_pin, 142 HAL_GPIO_OUTPUT_MUX_MAC_POWER_LED); 143 if (sc->sc_led_net_pin > 0) 144 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_led_net_pin, 145 HAL_GPIO_OUTPUT_MUX_MAC_NETWORK_LED); 146 } 147} 148 149static void 150ath_led_done(void *arg) 151{ 152 struct ath_softc *sc = arg; 153 154 sc->sc_blinking = 0; 155} 156 157/* 158 * Turn the LED off: flip the pin and then set a timer so no 159 * update will happen for the specified duration. 160 */ 161static void 162ath_led_off(void *arg) 163{ 164 struct ath_softc *sc = arg; 165 166 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, !sc->sc_ledon); 167 callout_reset(&sc->sc_ledtimer, sc->sc_ledoff, ath_led_done, sc); 168} 169 170/* 171 * Blink the LED according to the specified on/off times. 172 */ 173static void 174ath_led_blink(struct ath_softc *sc, int on, int off) 175{ 176 DPRINTF(sc, ATH_DEBUG_LED, "%s: on %u off %u\n", __func__, on, off); 177 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, sc->sc_ledon); 178 sc->sc_blinking = 1; 179 sc->sc_ledoff = off; 180 callout_reset(&sc->sc_ledtimer, on, ath_led_off, sc); 181} 182 183void 184ath_led_event(struct ath_softc *sc, int rix) 185{ 186 sc->sc_ledevent = ticks; /* time of last event */ 187 if (sc->sc_blinking) /* don't interrupt active blink */ 188 return; 189 ath_led_blink(sc, sc->sc_hwmap[rix].ledon, sc->sc_hwmap[rix].ledoff); 190} 191