1/* $NetBSD: s3c2xx0reg.h,v 1.4 2004/02/12 03:47:29 bsh Exp $ */ 2 3/*- 4 * Copyright (c) 2002, 2003 Fujitsu Component Limited 5 * Copyright (c) 2002, 2003 Genetec Corporation 6 * All rights reserved. 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 1. Redistributions of source code must retain the above copyright 12 * notice, this list of conditions and the following disclaimer. 13 * 2. Redistributions in binary form must reproduce the above copyright 14 * notice, this list of conditions and the following disclaimer in the 15 * documentation and/or other materials provided with the distribution. 16 * 3. Neither the name of The Fujitsu Component Limited nor the name of 17 * Genetec corporation may not be used to endorse or promote products 18 * derived from this software without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY FUJITSU COMPONENT LIMITED AND GENETEC 21 * CORPORATION ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, 22 * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 23 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 24 * DISCLAIMED. IN NO EVENT SHALL FUJITSU COMPONENT LIMITED OR GENETEC 25 * CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 26 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 27 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF 28 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND 29 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 30 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT 31 * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 32 * SUCH DAMAGE. 33 * 34 * $FreeBSD$ 35 */ 36 37/* s3c2410-specific registers */ 38#define UMCON_AFC (1 << 4) /* auto flow control */ 39#define UMSTAT_DCTS (1 << 2) /* CTS change */ 40#define ULCON_IR (1 << 6) 41#define ULCON_PARITY_SHIFT 3 42 43/* 44 * Exynos-specific 45 * 46 * UFSTAT_TXFULL register differs between Exynos and others. 47 * Others have UFSTAT_TXFULL (1 << 9) 48 */ 49#define UFSTAT_TXFULL (1 << 24) 50 51#define SSCOM_UINTM 0x038 52#define SSCOM_UINTP 0x030 53 54/* common for s3c2800 and s3c24x0 */ 55#define SSCOM_ULCON 0x00 /* UART line control */ 56#define ULCON_PARITY_NONE (0 << ULCON_PARITY_SHIFT) 57#define ULCON_PARITY_ODD (4 << ULCON_PARITY_SHIFT) 58#define ULCON_PARITY_EVEN (5 << ULCON_PARITY_SHIFT) 59#define ULCON_PARITY_ONE (6 << ULCON_PARITY_SHIFT) 60#define ULCON_PARITY_ZERO (7 << ULCON_PARITY_SHIFT) 61#define ULCON_STOP (1 << 2) 62#define ULCON_LENGTH_5 0 63#define ULCON_LENGTH_6 1 64#define ULCON_LENGTH_7 2 65#define ULCON_LENGTH_8 3 66#define SSCOM_UCON 0x04 /* UART control */ 67#define UCON_TXINT_TYPE (1 << 9) /* Tx interrupt. 0=pulse,1=level */ 68#define UCON_TXINT_TYPE_LEVEL UCON_TXINT_TYPE 69#define UCON_TXINT_TYPE_PULSE 0 70#define UCON_RXINT_TYPE (1 << 8) /* Rx interrupt */ 71#define UCON_RXINT_TYPE_LEVEL UCON_RXINT_TYPE 72#define UCON_RXINT_TYPE_PULSE 0 73#define UCON_TOINT (1 << 7) /* Rx timeout interrupt */ 74#define UCON_ERRINT (1 << 6) /* receive error interrupt */ 75#define UCON_LOOP (1 << 5) /* loopback */ 76#define UCON_SBREAK (1 << 4) /* send break */ 77#define UCON_TXMODE_DISABLE (0 << 2) 78#define UCON_TXMODE_INT (1 << 2) 79#define UCON_TXMODE_DMA (2 << 2) 80#define UCON_TXMODE_MASK (3 << 2) 81#define UCON_RXMODE_DISABLE (0 << 0) 82#define UCON_RXMODE_INT (1 << 0) 83#define UCON_RXMODE_DMA (2 << 0) 84#define UCON_RXMODE_MASK (3 << 0) 85#define SSCOM_UFCON 0x08 /* FIFO control */ 86#define UFCON_TXTRIGGER_0 (0 << 6) 87#define UFCON_TXTRIGGER_4 (1 << 6) 88#define UFCON_TXTRIGGER_8 (2 << 6) 89#define UFCON_TXTRIGGER_16 (3 << 6) 90#define UFCON_RXTRIGGER_4 (0 << 4) 91#define UFCON_RXTRIGGER_8 (1 << 4) 92#define UFCON_RXTRIGGER_12 (2 << 4) 93#define UFCON_RXTRIGGER_16 (3 << 4) 94#define UFCON_TXFIFO_RESET (1 << 2) 95#define UFCON_RXFIFO_RESET (1 << 1) 96#define UFCON_FIFO_ENABLE (1 << 0) 97#define SSCOM_UMCON 0x0c /* MODEM control */ 98#define UMCON_RTS (1 << 0) /* Request to send */ 99#define SSCOM_UTRSTAT 0x10 /* Status register */ 100#define UTRSTAT_TXSHIFTER_EMPTY ( 1<< 2) 101#define UTRSTAT_TXEMPTY (1 << 1) /* TX fifo or buffer empty */ 102#define UTRSTAT_RXREADY (1 << 0) /* RX fifo or buffer is not empty */ 103#define SSCOM_UERSTAT 0x14 /* Error status register */ 104#define UERSTAT_BREAK (1 << 3) /* Break signal, not 2410 */ 105#define UERSTAT_FRAME (1 << 2) /* Frame error */ 106#define UERSTAT_PARITY (1 << 1) /* Parity error, not 2410 */ 107#define UERSTAT_OVERRUN (1 << 0) /* Overrun */ 108#define UERSTAT_ALL_ERRORS \ 109 (UERSTAT_OVERRUN|UERSTAT_BREAK|UERSTAT_FRAME|UERSTAT_PARITY) 110#define SSCOM_UFSTAT 0x18 /* Fifo status register */ 111#define UFSTAT_RXFULL (1 <<8) /* Rx fifo full */ 112#define UFSTAT_TXCOUNT_SHIFT 4 /* TX FIFO count */ 113#define UFSTAT_TXCOUNT (0x0f << UFSTAT_TXCOUNT_SHIFT) 114#define UFSTAT_RXCOUNT_SHIFT 0 /* RX FIFO count */ 115#define UFSTAT_RXCOUNT (0x0f << UFSTAT_RXCOUNT_SHIFT) 116#define SSCOM_UMSTAT 0x1c /* Modem status register */ 117#define UMSTAT_CTS (1 << 0) /* Clear to send */ 118#if _BYTE_ORDER == _LITTLE_ENDIAN 119#define SSCOM_UTXH 0x20 /* Transmit data register */ 120#define SSCOM_URXH 0x24 /* Receive data register */ 121#else 122#define SSCOM_UTXH 0x23 /* Transmit data register */ 123#define SSCOM_URXH 0x27 /* Receive data register */ 124#endif 125#define SSCOM_UBRDIV 0x28 /* baud-reate divisor */ 126#define SSCOM_SIZE 0x2c 127