1/* 2 * include/linux/mfd/asic3.h 3 * 4 * Compaq ASIC3 headers. 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9 * 10 * Copyright 2001 Compaq Computer Corporation. 11 * Copyright 2007-2008 OpenedHand Ltd. 12 */ 13 14#ifndef __ASIC3_H__ 15#define __ASIC3_H__ 16 17#include <linux/types.h> 18 19struct asic3_platform_data { 20 u16 *gpio_config; 21 unsigned int gpio_config_num; 22 23 unsigned int irq_base; 24 25 unsigned int gpio_base; 26}; 27 28#define ASIC3_NUM_GPIO_BANKS 4 29#define ASIC3_GPIOS_PER_BANK 16 30#define ASIC3_NUM_GPIOS 64 31#define ASIC3_NR_IRQS ASIC3_NUM_GPIOS + 6 32 33#define ASIC3_IRQ_LED0 64 34#define ASIC3_IRQ_LED1 65 35#define ASIC3_IRQ_LED2 66 36#define ASIC3_IRQ_SPI 67 37#define ASIC3_IRQ_SMBUS 68 38#define ASIC3_IRQ_OWM 69 39 40#define ASIC3_TO_GPIO(gpio) (NR_BUILTIN_GPIO + (gpio)) 41 42#define ASIC3_GPIO_BANK_A 0 43#define ASIC3_GPIO_BANK_B 1 44#define ASIC3_GPIO_BANK_C 2 45#define ASIC3_GPIO_BANK_D 3 46 47#define ASIC3_GPIO(bank, gpio) \ 48 ((ASIC3_GPIOS_PER_BANK * ASIC3_GPIO_BANK_##bank) + (gpio)) 49#define ASIC3_GPIO_bit(gpio) (1 << (gpio & 0xf)) 50/* All offsets below are specified with this address bus shift */ 51#define ASIC3_DEFAULT_ADDR_SHIFT 2 52 53#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg) 54#define ASIC3_GPIO_OFFSET(base, reg) \ 55 (ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg) 56 57#define ASIC3_GPIO_A_BASE 0x0000 58#define ASIC3_GPIO_B_BASE 0x0100 59#define ASIC3_GPIO_C_BASE 0x0200 60#define ASIC3_GPIO_D_BASE 0x0300 61 62#define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4) 63#define ASIC3_GPIO_TO_BIT(gpio) ((gpio) - \ 64 (ASIC3_GPIOS_PER_BANK * ((gpio) >> 4))) 65#define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio)) 66#define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100)) 67#define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100)) 68 69#define ASIC3_GPIO_MASK 0x00 /* R/W 0:don't mask */ 70#define ASIC3_GPIO_DIRECTION 0x04 /* R/W 0:input */ 71#define ASIC3_GPIO_OUT 0x08 /* R/W 0:output low */ 72#define ASIC3_GPIO_TRIGGER_TYPE 0x0c /* R/W 0:level */ 73#define ASIC3_GPIO_EDGE_TRIGGER 0x10 /* R/W 0:falling */ 74#define ASIC3_GPIO_LEVEL_TRIGGER 0x14 /* R/W 0:low level detect */ 75#define ASIC3_GPIO_SLEEP_MASK 0x18 /* R/W 0:don't mask in sleep mode */ 76#define ASIC3_GPIO_SLEEP_OUT 0x1c /* R/W level 0:low in sleep mode */ 77#define ASIC3_GPIO_BAT_FAULT_OUT 0x20 /* R/W level 0:low in batt_fault */ 78#define ASIC3_GPIO_INT_STATUS 0x24 /* R/W 0:none, 1:detect */ 79#define ASIC3_GPIO_ALT_FUNCTION 0x28 /* R/W 1:LED register control */ 80#define ASIC3_GPIO_SLEEP_CONF 0x2c /* 81 * R/W bit 1: autosleep 82 * 0: disable gposlpout in normal mode, 83 * enable gposlpout in sleep mode. 84 */ 85#define ASIC3_GPIO_STATUS 0x30 /* R Pin status */ 86 87/* 88 * ASIC3 GPIO config 89 * 90 * Bits 0..6 gpio number 91 * Bits 7..13 Alternate function 92 * Bit 14 Direction 93 * Bit 15 Initial value 94 * 95 */ 96#define ASIC3_CONFIG_GPIO_PIN(config) ((config) & 0x7f) 97#define ASIC3_CONFIG_GPIO_ALT(config) (((config) & (0x7f << 7)) >> 7) 98#define ASIC3_CONFIG_GPIO_DIR(config) ((config & (1 << 14)) >> 14) 99#define ASIC3_CONFIG_GPIO_INIT(config) ((config & (1 << 15)) >> 15) 100#define ASIC3_CONFIG_GPIO(gpio, alt, dir, init) (((gpio) & 0x7f) \ 101 | (((alt) & 0x7f) << 7) | (((dir) & 0x1) << 14) \ 102 | (((init) & 0x1) << 15)) 103#define ASIC3_CONFIG_GPIO_DEFAULT(gpio, dir, init) \ 104 ASIC3_CONFIG_GPIO((gpio), 0, (dir), (init)) 105#define ASIC3_CONFIG_GPIO_DEFAULT_OUT(gpio, init) \ 106 ASIC3_CONFIG_GPIO((gpio), 0, 1, (init)) 107 108/* 109 * Alternate functions 110 */ 111#define ASIC3_GPIOA11_PWM0 ASIC3_CONFIG_GPIO(11, 1, 1, 0) 112#define ASIC3_GPIOA12_PWM1 ASIC3_CONFIG_GPIO(12, 1, 1, 0) 113#define ASIC3_GPIOA15_CONTROL_CX ASIC3_CONFIG_GPIO(15, 1, 1, 0) 114#define ASIC3_GPIOC0_LED0 ASIC3_CONFIG_GPIO(32, 1, 1, 0) 115#define ASIC3_GPIOC1_LED1 ASIC3_CONFIG_GPIO(33, 1, 1, 0) 116#define ASIC3_GPIOC2_LED2 ASIC3_CONFIG_GPIO(34, 1, 1, 0) 117#define ASIC3_GPIOC3_SPI_RXD ASIC3_CONFIG_GPIO(35, 1, 0, 0) 118#define ASIC3_GPIOC4_CF_nCD ASIC3_CONFIG_GPIO(36, 1, 0, 0) 119#define ASIC3_GPIOC4_SPI_TXD ASIC3_CONFIG_GPIO(36, 1, 1, 0) 120#define ASIC3_GPIOC5_SPI_CLK ASIC3_CONFIG_GPIO(37, 1, 1, 0) 121#define ASIC3_GPIOC5_nCIOW ASIC3_CONFIG_GPIO(37, 1, 1, 0) 122#define ASIC3_GPIOC6_nCIOR ASIC3_CONFIG_GPIO(38, 1, 1, 0) 123#define ASIC3_GPIOC7_nPCE_1 ASIC3_CONFIG_GPIO(39, 1, 0, 0) 124#define ASIC3_GPIOC8_nPCE_2 ASIC3_CONFIG_GPIO(40, 1, 0, 0) 125#define ASIC3_GPIOC9_nPOE ASIC3_CONFIG_GPIO(41, 1, 0, 0) 126#define ASIC3_GPIOC10_nPWE ASIC3_CONFIG_GPIO(42, 1, 0, 0) 127#define ASIC3_GPIOC11_PSKTSEL ASIC3_CONFIG_GPIO(43, 1, 0, 0) 128#define ASIC3_GPIOC12_nPREG ASIC3_CONFIG_GPIO(44, 1, 0, 0) 129#define ASIC3_GPIOC13_nPWAIT ASIC3_CONFIG_GPIO(45, 1, 1, 0) 130#define ASIC3_GPIOC14_nPIOIS16 ASIC3_CONFIG_GPIO(46, 1, 1, 0) 131#define ASIC3_GPIOC15_nPIOR ASIC3_CONFIG_GPIO(47, 1, 0, 0) 132#define ASIC3_GPIOD11_nCIOIS16 ASIC3_CONFIG_GPIO(59, 1, 0, 0) 133#define ASIC3_GPIOD12_nCWAIT ASIC3_CONFIG_GPIO(60, 1, 0, 0) 134#define ASIC3_GPIOD15_nPIOW ASIC3_CONFIG_GPIO(63, 1, 0, 0) 135 136 137#define ASIC3_SPI_Base 0x0400 138#define ASIC3_SPI_Control 0x0000 139#define ASIC3_SPI_TxData 0x0004 140#define ASIC3_SPI_RxData 0x0008 141#define ASIC3_SPI_Int 0x000c 142#define ASIC3_SPI_Status 0x0010 143 144#define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */ 145 146#define ASIC3_PWM_0_Base 0x0500 147#define ASIC3_PWM_1_Base 0x0600 148#define ASIC3_PWM_TimeBase 0x0000 149#define ASIC3_PWM_PeriodTime 0x0004 150#define ASIC3_PWM_DutyTime 0x0008 151 152#define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */ 153#define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */ 154 155#define ASIC3_LED_0_Base 0x0700 156#define ASIC3_LED_1_Base 0x0800 157#define ASIC3_LED_2_Base 0x0900 158#define ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */ 159#define ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */ 160#define ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */ 161#define ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */ 162 163/* LED TimeBase bits - match ASIC2 */ 164#define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */ 165 /* Note: max = 5 on hx4700 */ 166 /* 0: maximum time base */ 167 /* 1: maximum time base / 2 */ 168 /* n: maximum time base / 2^n */ 169 170#define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */ 171#define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */ 172#define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */ 173 174#define ASIC3_CLOCK_BASE 0x0A00 175#define ASIC3_CLOCK_CDEX 0x00 176#define ASIC3_CLOCK_SEL 0x04 177 178#define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */ 179#define CLOCK_CDEX_SOURCE0 (1 << 0) 180#define CLOCK_CDEX_SOURCE1 (1 << 1) 181#define CLOCK_CDEX_SPI (1 << 2) 182#define CLOCK_CDEX_OWM (1 << 3) 183#define CLOCK_CDEX_PWM0 (1 << 4) 184#define CLOCK_CDEX_PWM1 (1 << 5) 185#define CLOCK_CDEX_LED0 (1 << 6) 186#define CLOCK_CDEX_LED1 (1 << 7) 187#define CLOCK_CDEX_LED2 (1 << 8) 188 189/* Clocks settings: 1 for 24.576 MHz, 0 for 12.288Mhz */ 190#define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source */ 191#define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source ctrl */ 192#define CLOCK_CDEX_SMBUS (1 << 11) 193#define CLOCK_CDEX_CONTROL_CX (1 << 12) 194 195#define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */ 196#define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */ 197 198#define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select */ 199#define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select */ 200 201/* R/W: INT clock source control (32.768 kHz) */ 202#define CLOCK_SEL_CX (1 << 2) 203 204 205#define ASIC3_INTR_BASE 0x0B00 206 207#define ASIC3_INTR_INT_MASK 0x00 /* Interrupt mask control */ 208#define ASIC3_INTR_P_INT_STAT 0x04 /* Peripheral interrupt status */ 209#define ASIC3_INTR_INT_CPS 0x08 /* Interrupt timer clock pre-scale */ 210#define ASIC3_INTR_INT_TBS 0x0c /* Interrupt timer set */ 211 212#define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */ 213#define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */ 214#define ASIC3_INTMASK_MASK0 (1 << 2) 215#define ASIC3_INTMASK_MASK1 (1 << 3) 216#define ASIC3_INTMASK_MASK2 (1 << 4) 217#define ASIC3_INTMASK_MASK3 (1 << 5) 218#define ASIC3_INTMASK_MASK4 (1 << 6) 219#define ASIC3_INTMASK_MASK5 (1 << 7) 220 221#define ASIC3_INTR_PERIPHERAL_A (1 << 0) 222#define ASIC3_INTR_PERIPHERAL_B (1 << 1) 223#define ASIC3_INTR_PERIPHERAL_C (1 << 2) 224#define ASIC3_INTR_PERIPHERAL_D (1 << 3) 225#define ASIC3_INTR_LED0 (1 << 4) 226#define ASIC3_INTR_LED1 (1 << 5) 227#define ASIC3_INTR_LED2 (1 << 6) 228#define ASIC3_INTR_SPI (1 << 7) 229#define ASIC3_INTR_SMBUS (1 << 8) 230#define ASIC3_INTR_OWM (1 << 9) 231 232#define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */ 233#define ASIC3_INTR_CPS_SET (1 << 4) /* Time base enable */ 234 235 236/* Basic control of the SD ASIC */ 237#define ASIC3_SDHWCTRL_BASE 0x0E00 238#define ASIC3_SDHWCTRL_SDCONF 0x00 239 240#define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */ 241#define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */ 242#define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */ 243#define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* SD card detection: 0:low */ 244 245/* SD card write protection: 0=high */ 246#define ASIC3_SDHWCTRL_LEVWP (1 << 4) 247#define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 0=disable */ 248 249/* SD card power supply ctrl 1=enable */ 250#define ASIC3_SDHWCTRL_SDPWR (1 << 6) 251 252#define ASIC3_EXTCF_BASE 0x1100 253 254#define ASIC3_EXTCF_SELECT 0x00 255#define ASIC3_EXTCF_RESET 0x04 256 257#define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */ 258#define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */ 259#define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */ 260#define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */ 261#define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */ 262#define ASIC3_EXTCF_OWM_RESET (1 << 6) /* ?? used by OWM and CF */ 263#define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state */ 264#define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state */ 265#define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */ 266#define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */ 267#define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */ 268#define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */ 269#define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14) 270#define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */ 271 272/********************************************* 273 * The Onewire interface (DS1WM) is handled 274 * by the ds1wm driver. 275 * 276 *********************************************/ 277 278#define ASIC3_OWM_BASE 0xC00 279 280/***************************************************************************** 281 * The SD configuration registers are at a completely different location 282 * in memory. They are divided into three sets of registers: 283 * 284 * SD_CONFIG Core configuration register 285 * SD_CTRL Control registers for SD operations 286 * SDIO_CTRL Control registers for SDIO operations 287 * 288 *****************************************************************************/ 289#define ASIC3_SD_CONFIG_BASE 0x0400 /* Assumes 32 bit addressing */ 290#define ASIC3_SD_CTRL_BASE 0x1000 291#define ASIC3_SDIO_CTRL_BASE 0x1200 292 293#define ASIC3_MAP_SIZE_32BIT 0x2000 294#define ASIC3_MAP_SIZE_16BIT 0x1000 295 296#endif /* __ASIC3_H__ */ 297