Searched refs:deb_info (Results 1 - 25 of 35) sorted by relevance

12

/linux-master/drivers/media/common/b2c2/
H A Dflexcop-misc.c15 deb_info("found a FlexCopII.\n");
19 deb_info("found a FlexCopIIb.\n");
23 deb_info("found a FlexCopIII.\n");
33 deb_info("this FlexCop has the additional 32 hardware pid filter.\n");
35 deb_info("this FlexCop has the 6 basic main hardware pid filter.\n");
H A Dflexcop.h23 #define deb_info(args...) dprintk(0x01, args) macro
/linux-master/drivers/media/usb/dvb-usb/
H A Daz6027.h10 #define deb_info(args...) dprintk(dvb_usb_az6027_debug, 0x01, args) macro
H A Daf9005-fe.c142 deb_info("rsd counter not ready\n");
195 deb_info("POST abort count %d err count %d rsd packets %d\n",
239 deb_info("viterbi counter not ready\n");
271 deb_info("super frame count 0\n");
315 deb_info("PRE err count %d frame count %d bit count %d\n",
375 deb_info("GET STATISTIC\n");
380 deb_info("fecmon not available\n");
417 deb_info("REFRESH STATE\n");
471 deb_info("adjust for strong signal %d\n", temp);
790 deb_info("powe
[all...]
H A Dgp8psk.h21 #define deb_info(args...) dprintk(dvb_usb_gp8psk_debug,0x01,args) macro
H A Ddtt200u.h17 #define deb_info(args...) dprintk(dvb_usb_dtt200u_debug,0x01,args) macro
H A Dvp7045.c21 #define deb_info(args...) dprintk(dvb_usb_vp7045_debug,0x01,args) macro
132 deb_info("VP7045 EEPROM read (offs: %d, len: %d) : ", offset, i);
133 debug_dump(buf, i, deb_info);
148 deb_info("firmware says: %s ",buf);
152 deb_info("%s ",buf);
156 deb_info("v%s\n",buf);
H A Ddib0700_core.c100 deb_info("ep 0 read error (status = %d)\n",status);
143 deb_info("set the USB xfer len to %i Ts packet\n", nb_ts_packets);
148 deb_info("this firmware does not allow to change the USB xfer len\n");
214 deb_info("i2c read error (status = %d)\n", result);
219 deb_info("buffer too small to fit %d bytes\n",
246 deb_info("i2c message to big: %d\n",
267 deb_info("i2c write error (status = %d)\n", result);
302 deb_info("i2c xfer to big: %d\n",
318 deb_info("I2C read failed on address 0x%02x\n",
325 deb_info("i2
[all...]
H A Dvp702x.h9 #define deb_info(args...) dprintk(dvb_usb_vp702x_debug,0x01,args) macro
H A DcinergyT2.h28 #define deb_info(args...) dprintk(dvb_usb_cinergyt2_debug, 0x001, args) macro
H A Ddvb-usb-common.h18 #define deb_info(args...) dprintk(dvb_usb_debug,0x001,args) macro
H A Ddvb-usb-init.c141 deb_info("state before exiting everything: %x\n", d->state);
145 deb_info("state should be zero now: %x\n", d->state);
220 deb_info("check for cold %x %x\n", props->devices[i].cold_ids[j]->idVendor, props->devices[i].cold_ids[j]->idProduct);
233 deb_info("check for warm %x %x\n", props->devices[i].warm_ids[j]->idVendor, props->devices[i].warm_ids[j]->idProduct);
257 deb_info("power control: %d\n", onoff);
H A Ddib0700.h15 #define deb_info(args...) dprintk(dvb_usb_dib0700_debug,0x01,args) macro
H A Daz6027.c371 deb_info("%s %d", __func__, onoff);
461 deb_info("%s %d", __func__, slot);
516 deb_info("read cam data = %x from 0x%x", b[1], value);
629 deb_info("CAM Ready");
656 deb_info("%s", __func__);
717 deb_info("%s", __func__);
741 deb_info("%s", __func__);
766 deb_info("CI initialized.");
910 deb_info("adap = %p, dev = %p\n", adap, adap->dev);
914 deb_info("foun
[all...]
H A Dttusb2.c38 #define deb_info(args...) dprintk(dvb_usb_ttusb2_debug,0x01,args) macro
458 deb_info("%s: cmd=0x%02x sys=0x%02x\n", __func__, rx[2], rx[3]);
529 deb_info("TDA10086 attach failed\n");
554 deb_info("TDA10023 attach failed\n");
563 deb_info("TDA10048 attach failed\n");
596 deb_info("TDA8263 attach failed\n");
601 deb_info("LNBP21 attach failed\n");
H A Daf9005.c842 /* deb_info("rc_query\n"); */
896 deb_info("pid filter control onoff %d\n", onoff);
914 deb_info("pid filter control ok\n");
923 deb_info("set pid filter, index %d, pid %x, onoff %d\n", index,
929 deb_info("first pid set, enable pid table\n");
949 deb_info("last pid unset, disable pid table\n");
958 deb_info("set pid ok\n");
978 deb_info("result of FW_CONFIG in identify state %d\n", reply);
986 deb_info("Identify state cold = %d\n", *cold);
H A Ddib0700_devices.c801 deb_info("reset: %d", onoff);
810 deb_info("sleep: %d", onoff);
854 deb_info("WBD for DiB7000P: %d\n", offset + dib0070_wbd_offset(fe));
878 deb_info("WBD for DiB7000P: %d\n", offset + dib0070_wbd_offset(fe));
1299 deb_info("WBD for DiB8000: %d\n", offset);
1546 deb_info("AGC control callback: %i\n", restart);
1639 deb_info("PLL ratio=%i rest=%i\n", pll_ratio, rest);
1645 deb_info("optimal PLL ratio=%i\n", optimal_pll_ratio);
1662 deb_info("Warning : Rf frequency (%iHz) is not in the supported range, using VHF switch ", fe->dtv_property_cache.frequency);
1677 deb_info("onl
[all...]
H A Ddvb-usb-dvb.c153 deb_info("dvb_register_adapter failed: error %d", ret);
160 deb_info("dvb_usb_media_device_init failed: error %d", ret);
221 deb_info("unregistering DVB part\n");
/linux-master/drivers/media/dvb-frontends/
H A Dbcm3510.c76 #define deb_info(args...) dprintk(0x01,args) macro
96 deb_info("%s: i2c write error (addr %02x, reg %02x, err == %i)\n",
115 deb_info("%s: i2c read error (addr %02x, reg %02x, err == %i)\n",
165 deb_info("HAB is running already - clearing it.\n");
192 deb_info("waiting for HAB to complete\n");
201 deb_info("send_request execution timed out.\n");
257 deb_info("AP is busy\n");
312 deb_info("real_status: %02x\n",*status);
460 deb_info("%dkHz:",freq);
488 deb_info(" BC1_2_3_
[all...]
H A Dix2505v.c21 #define deb_info(args...) dprintk(0x01, args) macro
156 deb_info("Frq=%d x=%d N=%d A=%d\n", frequency, x, N, A);
200 deb_info("Osc=%x b_w=%x lpf=%x\n", local_osc, b_w, lpf);
201 deb_info("Data 0=[%4phN]\n", data);
222 deb_info("Data 2=[%x%x]\n", data[2], data[3]);
H A Dzl10036.c30 #define deb_info(args...) dprintk(0x01, args) macro
76 deb_info("%s: Power-On-Reset bit enabled - need to initialize the tuner\n",
139 deb_info("%s\n", __func__);
183 deb_info("%s: ftodo=%u fpriv=%u ferr=%d div=%u\n", __func__,
239 deb_info("%s: BW=%d br=%u bf=%u\n", __func__, fbw, br, bf);
290 deb_info("%s: c=%u rfg=%u ba=%u bg=%u\n", __func__, c, rfg, ba, bg);
403 deb_info("%s\n", __func__);
H A Dm88rs2000.c47 #define deb_info(args...) dprintk(0x01, args) macro
66 deb_info("%s: writereg error (reg == 0x%02x, val == 0x%02x, ret == %i)\n",
95 deb_info("%s: readreg error (reg == 0x%02x, ret == %i)\n",
189 deb_info("m88rs2000: m88rs2000_set_symbolrate\n");
200 deb_info("%s\n", __func__);
242 deb_info("%s\n", __func__);
436 deb_info("m88rs2000: init chip\n");
610 deb_info("%s: unsupported delivery system selected (%d)\n",
/linux-master/drivers/media/usb/dvb-usb-v2/
H A Dlmedm04.c86 #define deb_info(level, args...) lme_debug(dvb_usb_lme2510_debug, level, args) macro
88 deb_info(level, name" (%8phN)", p);
188 deb_info(1, "PID Setting Pid %04x", pid_out);
296 deb_info(5, "INT O/S C =%02x C/O=%02x Type =%02x%02x",
310 deb_info(1, "INT Key = 0x%08x", key);
411 deb_info(1, "PID Clearing Filter");
438 deb_info(3, "%s PID=%04x Index=%04x onoff=%02x", __func__,
528 deb_info(1, "i2c transfer failed.");
566 deb_info(1, "STM (%02x)", onoff);
572 deb_info(
[all...]
/linux-master/drivers/media/pci/b2c2/
H A Dflexcop-dma.c120 deb_info("%s\n", __func__);
169 deb_info("%s\n", __func__);
/linux-master/drivers/media/usb/b2c2/
H A Dflexcop-usb.c40 #define deb_info(args...) dprintk(0x01, args) macro
140 deb_info("unsupported request for v8_mem_req %x.\n", req);
204 deb_info("%x\n",
261 deb_info("unsupported function for i2c_req %x\n", func);

Completed in 279 milliseconds

12