| /u-boot/drivers/mmc/ |
| H A D | nexell_dw_mmc.c | 82 unsigned int delay; local
86 delay = NX_MMC_CLK_DELAY(priv->d_delay,
89 writel(delay, (host->ioaddr + DWMCI_CLKCTRL));
|
| /u-boot/drivers/net/ |
| H A D | ravb.c | 21 #include <linux/delay.h>
371 unsigned int delay; local
399 if (!dev_read_u32(dev, "rx-internal-delay-ps", &delay)) {
401 if (delay) {
407 if (!dev_read_u32(dev, "tx-internal-delay-ps", &delay)) {
409 if (delay) {
636 .delay = ravb_bb_delay,
|
| H A D | mdio_mux_meson_gxl.c | 14 #include <linux/delay.h>
|
| /u-boot/drivers/spi/ |
| H A D | davinci_spi.c | 21 #include <linux/delay.h>
79 dv_reg delay; /* 0x48 */ member in struct:davinci_spi_regs
243 * Including a minor delay. No science here. Should be good even with
244 * no delay
247 (50 << SPI_T2CDELAY_SHIFT), &ds->regs->delay);
|
| /u-boot/drivers/net/phy/ |
| H A D | dp83867.c | 190 /* Existing behavior was to use default pin strapping delay in rgmii
191 * mode, but rgmii should have meant no delay. Warn existing users.
207 /* RX delay *must* be specified if internal delay of RX is used. */
210 ret = ofnode_read_u32(node, "ti,rx-internal-delay",
213 pr_debug("ti,rx-internal-delay must be specified\n");
217 pr_debug("ti,rx-internal-delay value of %u out of range\n",
223 /* TX delay *must* be specified if internal delay of RX is used. */
226 ret = ofnode_read_u32(node, "ti,tx-internal-delay",
256 int val, delay, cfg2; local
[all...] |
| /u-boot/arch/arm/mach-uniphier/clk/ |
| H A D | pll-pro4.c | 7 #include <linux/delay.h>
|
| H A D | pll-base-ld20.c | 9 #include <linux/delay.h>
|
| /u-boot/drivers/usb/phy/ |
| H A D | twl4030.c | 27 #include <linux/delay.h>
|
| /u-boot/arch/arm/mach-uniphier/dram/ |
| H A D | ddrphy-training.c | 8 #include <linux/delay.h>
|
| /u-boot/drivers/net/octeontx/ |
| H A D | xcv.c | 17 #include <linux/delay.h>
|
| /u-boot/arch/arm/mach-uniphier/ |
| H A D | micro-support-card.c | 11 #include <linux/delay.h>
|
| /u-boot/arch/arm/mach-uniphier/arm32/ |
| H A D | psci.c | 9 #include <linux/delay.h>
|
| /u-boot/arch/mips/mach-octeon/include/mach/ |
| H A D | cvmx-l2c-defs.h | 162 int delay; member in struct:rlevel_byte_data
|
| /u-boot/board/udoo/ |
| H A D | udoo.c | 17 #include <linux/delay.h>
114 /* Need 100ms delay to exit from reset. */
|
| /u-boot/arch/mips/mach-octeon/ |
| H A D | cvmx-helper-fpa.c | 11 #include <linux/delay.h>
|
| /u-boot/drivers/watchdog/ |
| H A D | max6370_wdt.c | 7 #include <linux/delay.h>
|
| H A D | bcm2835_wdt.c | 12 #include <linux/delay.h>
|
| H A D | npcm_wdt.c | 11 #include <linux/delay.h>
|
| /u-boot/drivers/serial/ |
| H A D | serial_octeon_bootcmd.c | 17 #include <linux/delay.h>
|
| /u-boot/board/imgtec/malta/ |
| H A D | malta.c | 18 #include <linux/delay.h>
|
| /u-boot/drivers/power/ |
| H A D | twl4030.c | 27 #include <linux/delay.h>
165 mdelay(100); /* ramp-up delay from Linux code */
173 mdelay(100); /* ramp-up delay from Linux code */
|
| /u-boot/arch/m68k/lib/ |
| H A D | time.c | 13 #include <linux/delay.h>
|
| /u-boot/board/cssi/cmpc885/ |
| H A D | sdram.c | 9 #include <linux/delay.h>
|
| /u-boot/lib/ |
| H A D | time.c | 19 #include <linux/delay.h>
|
| /u-boot/board/renesas/lager/ |
| H A D | lager.c | 25 #include <linux/delay.h>
|