Searched hist:172313 (Results 1 - 2 of 2) sorted by relevance
| /freebsd-9.3-release/sys/modules/acpi/acpi/ | ||
| H A D | Makefile | diff 172313 Mon Sep 24 14:59:06 MDT 2007 njl Rewrite the EC driver event model. The main goal is to avoid polling/interrupt-driven fallback and instead use polling only during boot and pure interrupt-driven mode after boot. Polled mode could be relegated completely to a legacy role if we could enable interrupts during boot. Polled mode can be forced after boot by setting debug.acpi.ec.polled="1", i.e. if there are timeouts. - Use polling only during boot, shutdown, or if requested by the user. Otherwise, use a generation count of GPEs, incremented atomically. This prevents an old status value from being used if the EC is really slow and the same condition (i.e. multiple IBEs for a write transaction) is being checked. - Check for and run the query handler directly if the SCI bit is set in the status register during boot. Previously, the query handler wouldn't run until interrupts were finally enabled late in boot. - During boot and after starting a command, check if the event appears to already have occurred before we even start waiting. If so, it's possible the EC is very slow and we might accept an old status value. Print a warning in this case. Once we've booted, interrupt-driven mode should work just fine but polled mode could be unreliable. There's not much more we can do about this until interrupts are enabled during boot. - In the above case, we also do one final check if the interrupt-driven mode gets a timeout. If the status is complete, it will force the system back into polled mode since interrupt mode doesn't work. For polled mode during boot, if the status appears to be already complete before beginning the check loop, it waits 10 us before actually checking the status, just in case the EC is really slow and hasn't gotten to work on the new request yet. - Use upper-case hex for the _Qxx method - Use device_printf for errors, don't hide them under verbose - Increase default total timeout to 750 ms and decrease polling interval to 5 us. - Don't pass the status value via the softc. Just read it directly. - Remove the mutex. We use the sx lock for transaction serialization with the query handler. - Remove the Intel copyright notice as no code of theirs was ever present in this file (verified against rev 1.1) - Allow KTR module-only builds for ease of testing Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing. Approved by: re MFC after: 2 weeks |
| /freebsd-9.3-release/sys/dev/acpica/ | ||
| H A D | acpi_ec.c | diff 172313 Mon Sep 24 14:59:06 MDT 2007 njl Rewrite the EC driver event model. The main goal is to avoid polling/interrupt-driven fallback and instead use polling only during boot and pure interrupt-driven mode after boot. Polled mode could be relegated completely to a legacy role if we could enable interrupts during boot. Polled mode can be forced after boot by setting debug.acpi.ec.polled="1", i.e. if there are timeouts. - Use polling only during boot, shutdown, or if requested by the user. Otherwise, use a generation count of GPEs, incremented atomically. This prevents an old status value from being used if the EC is really slow and the same condition (i.e. multiple IBEs for a write transaction) is being checked. - Check for and run the query handler directly if the SCI bit is set in the status register during boot. Previously, the query handler wouldn't run until interrupts were finally enabled late in boot. - During boot and after starting a command, check if the event appears to already have occurred before we even start waiting. If so, it's possible the EC is very slow and we might accept an old status value. Print a warning in this case. Once we've booted, interrupt-driven mode should work just fine but polled mode could be unreliable. There's not much more we can do about this until interrupts are enabled during boot. - In the above case, we also do one final check if the interrupt-driven mode gets a timeout. If the status is complete, it will force the system back into polled mode since interrupt mode doesn't work. For polled mode during boot, if the status appears to be already complete before beginning the check loop, it waits 10 us before actually checking the status, just in case the EC is really slow and hasn't gotten to work on the new request yet. - Use upper-case hex for the _Qxx method - Use device_printf for errors, don't hide them under verbose - Increase default total timeout to 750 ms and decrease polling interval to 5 us. - Don't pass the status value via the softc. Just read it directly. - Remove the mutex. We use the sx lock for transaction serialization with the query handler. - Remove the Intel copyright notice as no code of theirs was ever present in this file (verified against rev 1.1) - Allow KTR module-only builds for ease of testing Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing. Approved by: re MFC after: 2 weeks |
Completed in 66 milliseconds