Searched hist:1064 (Results 1 - 20 of 20) sorted by relevance
/freebsd-10.2-release/sys/dev/cxgbe/ | ||
H A D | t4_netmap.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) 266757 Tue May 27 18:24:51 MDT 2014 np cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... Relnotes: Yes Sponsored by: Chelsio Communications. |
H A D | t4_tracer.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | offload.h | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | t4_sge.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | adapter.h | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | t4_main.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/modules/cxgbe/iw_cxgbe/ | ||
H A D | Makefile | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/modules/cxgbe/t4_firmware/ | ||
H A D | Makefile | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/modules/cxgbe/t5_firmware/ | ||
H A D | Makefile | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/modules/cxgbe/tom/ | ||
H A D | Makefile | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/dev/cxgbe/tom/ | ||
H A D | t4_ddp.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | t4_cpl_io.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | t4_tom.h | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/modules/cxgbe/ | ||
H A D | Makefile | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/modules/cxgbe/if_cxgbe/ | ||
H A D | Makefile | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/dev/cxgbe/common/ | ||
H A D | common.h | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
H A D | t4_hw.c | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
/freebsd-10.2-release/sys/i386/conf/ | ||
H A D | NOTES | diff 1064 Tue Feb 01 08:34:16 MST 1994 ache Add FADE_SAVER option from new syscons. |
/freebsd-10.2-release/sys/conf/ | ||
H A D | NOTES | diff 1064 Tue Feb 01 08:34:16 MST 1994 ache Add FADE_SAVER option from new syscons. |
H A D | files | diff 270297 Thu Aug 21 20:04:07 MDT 2014 np MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411, r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe portion of r270063. r266571: cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet. r266757: cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards. Netmap gets its own hardware-assisted virtual interface and won't take over or disrupt the "normal" interface in any way. You can use both simultaneously. For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface (note the 'n' prefix) in the hardware to accompany each cxl<N> interface. These two ifnet's per port share the same wire but really are separate interfaces in the hardware and software. Each gets its own L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You should run netmap on the 'n' interfaces only, that's what they are for. With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now. Single port receive is at 33Mpps but this is very much a work in progress. I expect it to be closer to 40Mpps once done. In any case the current effort can already saturate multiple 10G ports of a T5 card at the smallest legal packet size. T4 gear is totally untested. trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef 881.952141 main [1621] interface is ncxl0 881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0 881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0 881.962540 main [1804] mapped 334980KB at 0x801dff000 Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus. 10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef) 881.962562 main [1882] Sending 512 packets every 0.000000000 s 881.962563 main [1884] Wait 2 secs for phy reset 884.088516 main [1886] Ready... 884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1 884.088607 sender_body [996] start 884.093246 sender_body [1064] drop copy 885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec) 886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec) 887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec) 888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec) 889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec) 890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec) 891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec) 892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec) 893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec) 894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec) 895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec) 896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec) ... r268536: cxgbe(4): Add an iSCSI softc to the adapter structure. r269076: Some hooks in cxgbe(4) for the offloaded iSCSI driver. r269364: Improve compliance with style.Makefile(5). r269366: List one file per line in the Makefiles. This makes it easier to read diffs when a file is added or removed. r269411: cxgbe(4): minor optimizations in ingress queue processing. Reorganize struct sge_iq. Make the iq entry size a compile time constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly. r269413: cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell address of an egress queue. r269428: cxgbe(4): some optimizations in freelist handling. r269440: cxgbe(4): Remove an unused version of t4_enable_vi. r269537: cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global mutex around ifpromisc in at least the bpf_dtor path. r269644: cxgbe(4): Let caller specify whether it's ok to sleep in t4_sched_config and t4_sched_params. r269731: cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa). Relnotes: Yes (native netmap support for Chelsio T4/T5 cards) |
Completed in 1153 milliseconds