- Copy stable/10@285827 to releng/10.2 in preparation for 10.2-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.2.
- Update default pkg(8) configuration to use the quarterly branch.[1]

Discussed with: re, portmgr [1]
Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411,
r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe
portion of r270063.

r266571:
cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet.

r266757:
cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards.
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.

For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.

With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.

trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...

r268536:
cxgbe(4): Add an iSCSI softc to the adapter structure.

r269076:
Some hooks in cxgbe(4) for the offloaded iSCSI driver.

r269364:
Improve compliance with style.Makefile(5).

r269366:
List one file per line in the Makefiles. This makes it easier to read
diffs when a file is added or removed.

r269411:
cxgbe(4): minor optimizations in ingress queue processing.

Reorganize struct sge_iq. Make the iq entry size a compile time
constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly.

r269413:
cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell
address of an egress queue.

r269428:
cxgbe(4): some optimizations in freelist handling.

r269440:
cxgbe(4): Remove an unused version of t4_enable_vi.

r269537:
cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when
IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global
mutex around ifpromisc in at least the bpf_dtor path.

r269644:
cxgbe(4): Let caller specify whether it's ok to sleep in
t4_sched_config and t4_sched_params.

r269731:
cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa).

Relnotes: Yes (native netmap support for Chelsio T4/T5 cards)

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

cxgbe(4): Updates to the hardware L2 table management code.

- Add full support for IPv6 addresses.

- Read the size of the L2 table during attach. Do not assume that PCIe
physical function 4 of the card has all of the table to itself.

- Use FNV instead of Jenkins to hash L3 addresses and drop the private
copy of jhash.h from the driver.

MFC after: 1 week

Support for TCP DDP (Direct Data Placement) in the T4 TOE module.

Basically, this is automatic rx zero copy when feasible. TCP payload is
DMA'd directly into the userspace buffer described by the uio submitted
in soreceive by an application.

- Works with sockets that are being handled by the TCP offload engine
of a T4 chip (you need t4_tom.ko module loaded after cxgbe, and an
"ifconfig +toe" on the cxgbe interface).
- Does not require any modification to the application.
- Not enabled by default. Use hw.t4nex.<X>.toe.ddp="1" to enable it.

Assume INET, INET6, and TCP_OFFLOAD when the driver is built out of tree and
KERNBUILDDIR is not set.

MFC after: 2 weeks

- Updated TOE support in the kernel.

- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.

- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.

Build-tested with make universe.

30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE

Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe

Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe

Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)