mellanox/mlxsw/reg.h

82  * Master - if set, then the record describes the master system port.
88  * Note: Must be set for Spectrum.
120  * Controls the Switch aging time. Aging time is able to be set per Switch
459  * For Spectrum this value must be set to 0x1FFF
829  * Should be set to 0 when virtual ports are not enabled on the port.
885  * Priority tagged. If this bit is set, packets forwarded to the port with
886  * untagged VLAN membership (u bit is set) will be tagged with priority tag
894  * the pt bit will NOT be updated. To update the pt bit, pte must be set.
907  * Should be set to 0 when virtual ports are not enabled on the port.
990  * Should be set to 0 when virtual ports are not enabled on the port.
996  * When set, untagged frames on the ingress are allowed (default).
1002  * When set, priority tagged frames on the ingress are allowed (default).
1008  * When set, tagged frames on the ingress are allowed (default).
1390  * LAG hashing configuration. This is a bitmask, in which each set
1514  * Should be set to 0 when virtual ports are not enabled on the port.
1589  * Valid if set.
1609  * Counter set type for flow counters.
1636  * Must not be set for a non enabled RIF.
1721  * When set, the Port Prio Mode is updated with the provided ipprio_mode field.
1729  * When set, the Ingress Port VID Mode is updated with the provided ipvid_mode
1738  * When set, the Egress Port VID Mode is updated with the provided epvid_mode
1862  * router-sub-port local_port. Must not be set for a FID which is not a
1863  * router-sub-port and must be set prior to enabling the relevant RIF.
1894  * If not set, then nve_tunnel_flood_ptr is reserved and considered NULL.
1911  * If not set, then vni is reserved.
1931  * Must not be set for a non valid RIF.
2247  * is set.
2262  * Egress EtherType VLAN to push when SPVID.egr_et_set field set for the packet:
2371 					bool set, bool smpe_valid, u16 smpe)
2376 	mlxsw_reg_smid2_port_set(payload, port, set);
2625  * group - When set, the binding is of an ACL group. When cleared,
2627  * Must be set to 1 for Spectrum.
2633  * ACL/ACL group identifier. If the g bit is set, this field should hold
2786  * Type of action set to be used on this region.
3062  * For a new entry: set if ca=0, clear if ca=1
3079  * Action-set to perform when rule is matched.
3080  * Must be zero padded if action set is shorter.
3171 	 * All R/W fields are relevant for new entry. Activity bit is set
3175 	/* Update action. Only action set will be updated. */
3217  * mask- in the same size as key. A bit that is set directs the TCAM
3226  * ACL action set.
3281  * 0 - The eRP is used only if bloom filter state is set for the given
3416 	 * All R/W fields are relevant for new entry. Activity bit is set
3472  * Delta mask must not be set for reserved fields in the key blocks.
3492  * Note: In Spectrum-2, a region of 8 key blocks must be set to either
3983 	/* Forward and set color to red.
4052  * Should be set to 0 when virtual ports are not enabled on the port.
4569  * Written only when ptsc_we is set.
4703  * MTU value to set port to. Must be smaller or equal to max_mtu.
4705  * MTU is set.
4733  * Note: When set while the link is up, the changes will not take effect
4835  * Extended speed and protocol to set port to.
4841  * Speed and protocol to set port to.
4939  * reserved. HW will set incremental
4996  * 4 - Disabled by system. Can only be set by hardware.
5018  * Event update enable. If this bit is set, event generation will be
5090  * 1 - Enabled. When auto-negotiation is performed, set the Pause policy
5094  * Note: The auto-negotiation advertisement is set according to pptx and
5095  * pprtx. When PFC is set on Tx / Rx, ppan must be set to 0.
5232  * clr bit set.
5250  * for all counters in the counter group. This bit can be set
5265  * Priority for counter set that support per priority, valid values: 0-7.
5266  * Traffic class for counter set that support per traffic class,
5837  * If epsb is set, packets assigned to buffer are allowed to insert the port
5990  * If this bit is set, admin state will be updated based on admin_state field.
5998  * If this bit is set, event generation will be updated based on the e field.
6038 /* Phy local loopback. When set the port's egress traffic is looped back
6139  * Event update enable. If this bit is set, event generation will be updated
6146  * Software ignore enable bit. If this bit is set, the value of swi is used.
6154  * Software ignore. If this bit is set, the device shouldn't generate events
6282  * The register can only be set when the module is disabled by PMAOS register.
6302  * When set, will keep eeprom_override values after plug-out event.
6385  * The register can only be set when the module is disabled by PMAOS register
6616  * If set, then the device will wait for the event it sent to be acknowledged
6647  * Note: Must be set to 0 (forward) for event trap IDs, as they are already
6748  * 0 - Activity will be set when an entry is hit (default).
6749  * 1 - Activity will not be set when an entry is hit.
6886  * If the flag is set then loop-back filter for unicast packets is
6969  * LAG indication. When this bit is set the system_port field holds the
6976  * Port unique indentifier. When lag bit is set, this field holds the
7075 	 *	  same set of counters for the different type of traffic
7294 	 * The write may not succeed if the activity is set. There is not
7297 	 * response to the set command).
7418 	/* IPv4, address set by mlxsw_reg_ratr_ipip_ipv4_udip. */
7420 	/* IPv6, address set by mlxsw_reg_ratr_ipip_ipv6_ptr. */
7455  * Counter set type for flow counters
7570 	 *	  same set of counters for the different type of traffic
7780  * RALST is used to set and query the structure of an LPM tree.
7783  * will refer to. Therefore, bin X refers to a set of entries with prefixes
7914 	 * fields are written for new entry. Activity bit is set
8005  * field must be set.
8199 	 * relevant for new entry. Activity bit is set for new entries.
8271  * Counter set type for flow counters
8624 /* If set, allow decapsulation of IPinIP (without GRE). */
8626 /* If set, allow decapsulation of IPinGREinIP without a key. */
8628 /* If set, allow decapsulation of IPinGREinIP with a key. */
8849  * Note that low-entries must be set if high-entries are set. For
8850  * example: if erif_entry[2].v is set then erif_entry[1].v and
8851  * erif_entry[0].v must be set.
9046 	 * fields are relevant for new entry. Activity bit is set for new
9104  * A bit that is set directs the TCAM to compare the corresponding bit in key. A
9119  * A bit that is set directs the TCAM to compare the corresponding bit in key. A
9127  * ACL action set. The only supported action types in this field and in any
9128  * action-set pointed from here are as follows:
10140  * When set, latency-TLV is supported.
10146  * When set, string-TLV is supported.
10455  * Component properties set.
10670 	/* If set, MCIA supports 128 bytes payloads. Otherwise, 48 bytes. */
10672 	/* If set, MRSR.command=6 is supported. */
10681  * When bit is set, the feature is supported in the device.
10773  * Counter set type.
11386  * Opcode Event Enable. When set a BCTOE event will be sent once the opcode
11567  * When set to '1', each change in the slot_info.provisioned / sr_valid /
11609  * If set, the data in the data field is valid and contain the information
11616  * If set, the INI file is applied and the card is provisioned.
11622  * If set, Shift Register is valid (after being provisioned) and data
11635  * If set, the LC is powered on, matching the INI version and a new FW
11642  * If set, the FW has completed the MDDC.device_enable command.
11702  * If set, the device is the flash owner. Otherwise, a shared flash
11800  * When set, FW is the manager and allowed to program the downstream device.
12116  * The hash is set by LAG hash.
12126  * The hash is set by LAG hash.
12268  * The TNQCR register configures how QoS is set in encapsulation into the
12277  * For encapsulation: How to set DSCP field:
12570  * When set, configures descriptor buffer.
12755  * When this bit is set, max_buff_occupancy field is cleared (and a
12878  * Clear Max Buffer Occupancy. When this bit is set, the max_buff_occupancy
12897  * Indicates which of the ports (for which the relevant bit is set)
12898  * are affected by the set operation. Configuration of any other port
12906  * Indicates which of the priorities (for which the relevant bit is set)
12907  * are affected by the set operation. Configuration of any other priority
12916  * Indicates which of the ports (for which the relevant bit is set)
12917  * are affected by the set operation. Configuration of any other port
12926  * set) are affected by the set operation. Configuration of any other
13194  * 4 - Disabled by system. Can only be set by hardware.