powerpc/mpc85xx: use board env file for socrates board

as Tom suggested get rid of CFG_EXTRA_ENV_SETTINGS and
enable CONFIG_ENV_SOURCE_FILE and use text file

board/socrates/socrates.env

which contains the default environment. While at it,
cleanup the default Environment.

Signed-off-by: Heiko Schocher <hs@denx.de>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

powerpc/mpc85xx: socrates: enable protected Environment

enable protected Environment on socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>

powerpc/mpc85xx: socrates: drop second flash bank

drop second flash bank, as not used anymore.

Signed-off-by: Heiko Schocher <hs@denx.de>

powerpc/mpc85xx: socrates: add initrd_high default environment variable

we need to set initrd_high to get fitimage booting.

Without, U-Boot drops when booting fitimage:

ERROR: Failed to allocate 0x59a0b6 bytes below 0x800000.
ramdisk - allocation error
bootm - boot application image from memory

Signed-off-by: Heiko Schocher <hs@denx.de>

powerpc/mpc85xx: socrates: add MTD partitioning support

setup MTD partitioning through mtdparts variable
and set it to:

mtdparts=fe0000000.nor:13312k(system1),13312k(system2),5120k(data),128k(env),128k(env-red),768k(u-boot)

and pass this to linux per kernel commandline.

Signed-off-by: Heiko Schocher <hs@denx.de>

global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFG

Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_L2_CACHE to Kconfig

This converts the following to Kconfig:
CONFIG_L2_CACHE

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Remove unused CONFIG symbols

This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM

And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

net: tsec: Remove non-DM_ETH support code

As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPD_EEPROM to Kconfig

This converts the following to Kconfig:
CONFIG_SPD_EEPROM

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_PCI* to CFG_SYS_PCI*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Remove unused symbols

This commit removes the following unused symbols:
CONFIG_SYS_NVRAM_BASE_ADDR
CONFIG_SYS_NVRAM_SIZE
CONFIG_SYS_PAXE_BASE
CONFIG_SYS_PCCNT
CONFIG_SYS_PCDAT
CONFIG_SYS_PCDDR
CONFIG_SYS_PCI1_ADDR
CONFIG_SYS_PCI2_ADDR
CONFIG_SYS_PCI1_IO_BUS
CONFIG_SYS_PCI1_IO_SIZE
CONFIG_SYS_PCI1_MEM_BUS
CONFIG_SYS_PCI1_MEM_SIZE
CONFIG_SYS_PCIE3_ADDR
CONFIG_SYS_PCIE4_ADDR
CONFIG_SYS_PCIE3_IO_PHYS
CONFIG_SYS_PCIE3_IO_VIRT
CONFIG_SYS_PCIE4_IO_PHYS
CONFIG_SYS_PCIE4_IO_VIRT
CONFIG_SYS_PLL_SETTLING_TIME
CONFIG_SYS_QMAN_CENA_BASE
CONFIG_SYS_QMAN_SP_CENA_SIZE
CONFIG_SYS_RCAR_I2C0_BASE
CONFIG_SYS_RCAR_I2C1_BASE
CONFIG_SYS_RCAR_I2C2_BASE
CONFIG_SYS_RCAR_I2C3_BASE
CONFIG_SYS_SATA
CONFIG_SYS_SDRAM_BASE2
CONFIG_SYS_SGMII_REFCLK_MHZ
CONFIG_SYS_SGMII_LINERATE_MHZ
CONFIG_SYS_SGMII_RATESCALE
CONFIG_SYS_SH_SDHI0_BASE
CONFIG_SYS_SH_SDHI0_BASE
CONFIG_SYS_SH_SDHI1_BASE
CONFIG_SYS_SH_SDHI2_BASE
CONFIG_SYS_SH_SDHI3_BASE
CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
CONFIG_SYS_SPI_U_BOOT_SIZE
CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR
CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN
CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT
CONFIG_SYS_VCXK_BASE
CONFIG_SYS_VCXK_DEFAULT_LINEALIGN
CONFIG_SYS_VCXK_DOUBLEBUFFERED
CONFIG_SYS_VCXK_ENABLE_DDR
CONFIG_SYS_VCXK_ENABLE_PIN
CONFIG_SYS_VCXK_ENABLE_PORT
CONFIG_SYS_VCXK_INVERT_DDR
CONFIG_SYS_VCXK_INVERT_PIN
CONFIG_SYS_VCXK_INVERT_PORT
CONFIG_SYS_VCXK_REQUEST_DDR
CONFIG_SYS_VCXK_REQUEST_PIN
CONFIG_SYS_VCXK_REQUEST_PORT
CONFIG_SYS_VSC7385_BR_PRELIM
CONFIG_SYS_VSC7385_OR_PRELIM

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NAND_* to CFG_SYS_NAND_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MAX_NAND_DEVICE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_LOADS_BAUD_CHANGE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_LOADS_BAUD_CHANGE
CONFIG_LOADS_ECHO

As part of this, we move CMD_SAVES to be after CMD_LOADS as they are
logically related (load or save an s-record format file) and this makes
grouping of CONFIG_SYS_LOADS_BAUD_CHANGE easier.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Remove unused symbols CONFIG_SYS_JFFS2_FIRST_BANK et al

This removes the following symbols:
CONFIG_RTC_MCFRRTC
CONFIG_SYS_JFFS2_FIRST_BANK
CONFIG_SYS_JFFS2_FIRST_SECTOR
CONFIG_SYS_JFFS2_NUM_BANKS
CONFIG_SYS_LBC_CACHE_BASE
CONFIG_SYS_LIME_SIZE
CONFIG_SYS_MAMR
CONFIG_SYS_MCFRRTC_BASE
CONFIG_SYS_MONITOR_SEC

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_INIT_RAM_LOCK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_INIT_RAM_LOCK

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Remove CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR et al

This removes the following symbols:
CONFIG_SYS_FSL_DSPI_BE
CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR
CONFIG_SYS_FSL_DSP_CCSR_DDR_OFFSET
CONFIG_SYS_FSL_DSP_DDR_ADDR
CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
CONFIG_SYS_FSL_ERRATUM_A008751
CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
CONFIG_SYS_FSL_ESDHC_NUM
CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK
CONFIG_SYS_FSL_FM1_RX0_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX1_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX2_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX3_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX4_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX5_1G_OFFSET
CONFIG_SYS_FSL_ISBC_VER
CONFIG_SYS_FSL_QSPI_LE
CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR
CONFIG_SYS_FSL_SCFG_IODSECR1_OFFSET
CONFIG_SYS_FSL_SCFG_PIXCLKCR_OFFSET
CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR
CONFIG_SYS_FSL_SRDS_NUM_PLLS
CONFIG_SYS_FSL_WDOG_BE
CONFIG_SYS_GP1DIR
CONFIG_SYS_GP1ODR
CONFIG_SYS_GP2DIR
CONFIG_SYS_GP2ODR
CONFIG_SYS_HALT_BEFOR_RAM_JUMP
CONFIG_SYS_HMI_BASE
FSL_QSPI_FLASH_NUM
FSL_QSPI_FLASH_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_QUIET_TEST to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_QUIET_TEST

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MAX_FLASH_SECT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_FLASH_SECT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_ERASE_TOUT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT

In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_CHECKSUM to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_CHECKSUM

Signed-off-by: Tom Rini <trini@konsulko.com>

usb: ohci-hcd: Remove some unused legacy code

At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USB_OHCI_NEW et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW

Signed-off-by: Tom Rini <trini@konsulko.com>

socrates: Rework CONFIG_PCI_CLK_FREQ

The symbol CONFIG_PCI_CLK_FREQ is local to this board. Provide equal
clarity in the code by referencing the numeric value directly and move
the explanatory comment to the code, just prior to use.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_SPD_BUS_NUM to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPD_BUS_NUM

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENABLE_36BIT_PHYS to Kconfig

This converts the following to Kconfig:
CONFIG_ENABLE_36BIT_PHYS

Signed-off-by: Tom Rini <trini@konsulko.com>

Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>

powerpc: Switch to using CONFIG_SYS_INIT_SP_OFFSET from CONFIG_SYS_GBL_DATA_OFFSET

In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_DIMM_SLOTS_PER_CTLR to Kconfig

This converts the following to Kconfig:
CONFIG_DIMM_SLOTS_PER_CTLR

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ETHPRIME to Kconfig

This converts the following to Kconfig:
CONFIG_ETHPRIME

This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.

Signed-off-by: Tom Rini <trini@konsulko.com>

Remove CONFIG_HAS_ETH0 et al symbols

This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3

This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.

Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CHIP_SELECTS_PER_CTRL to Kconfig

This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL

Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BTB to Kconfig

This converts the following to Kconfig:
CONFIG_BTB

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_TIMESTAMP to Kconfig

This converts the following to Kconfig:
CONFIG_TIMESTAMP

Signed-off-by: Simon Glass <sjg@chromium.org>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_WATCHDOG, HW_WATCHDOG and WDT to Kconfig

Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.

For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.

For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_BR0_PRELIM et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM

This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig

This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>

kgdb: Remove unused serial related options

We have a few CONFIG options for KGDB that are not referenced, remove
them.

Signed-off-by: Tom Rini <trini@konsulko.com>

WS cleanup: remove SPACE(s) followed by TAB

Signed-off-by: Wolfgang Denk <wd@denx.de>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

nxp: Migrate a number of DDR related symbols to Kconfig

- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Remove unused or unnecessary CONFIG symbols related to DDR

These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

treewide: mem: Move mtest related defines to Kconfig

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mpc85xx, socrates: add DM PCI support

add DM PCI support on the socrates board.
use PCIE_FSL now.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: enable DM serial

switch to DM_SERIAL support.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: enable DM I2C

enable DM I2C support for the socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: disable VIDEO

disable video, as not really needed longer.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: add DM support

enable CONFIG_DM for the socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: suppress unknown flash warning

suppress warning:
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOT

In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be
defined for each board. To prepare for conversion to Kconfig, add this.

Signed-off-by: Simon Glass <sjg@chromium.org>

rtc: move RTC_RX8025 to Kconfig

move RTC_RX8025 to Kconfig and fixup board configs.

Signed-off-by: Heiko Schocher <hs@denx.de>

configs: fsl: move DDR specific defines to Kconfig

Moves below DDR specific defines to Kconfig:

CONFIG_FSL_DDR_BIST
CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
CONFIG_FSL_DDR_INTERACTIVE
CONFIG_FSL_DDR_SYNC_REFRESH

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MISC_INIT_R to Kconfig

This converts the following to Kconfig:
CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

treewide: Migrate CONFIG_TSEC_ENET to Kconfig

Migrate the CONFIG_TSEC_ENET option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to Kconfig

Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

include/configs: remove numerous CONFIG_SYS_BARGSIZE definitions

This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
equal to CONFIG_SYS_CBSIZE in numerous configuration files.

We remove such definitions in two situations:

- CONFIG_SYS_CBSIZE is otherwise not defined in the board
configuration file, which means the default value of
CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
larger.

- CONFIG_SYS_CBSIZE is defined in the board configuration file, but
to a value equal or less than 512. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
is equal or larger.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_PBSIZE

Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_CMD_REGINFO to Kconfig

This patch converts CONFIG_CMD_REGINFO to Kconfig

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_CMD_PCI to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

configs: Finish migration of PHY_GIGE

Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Convert CONFIG_ENV_IS_IN_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_CMD_EEPROM et al to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>

Drop digital thermometer and thermostat (DTT) drivers

This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

cmd: add Kconfig option for 'date' command

Signed-off-by: Chris Packham <judge.packham@gmail.com>
[trini: default y if DM_RTC, re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_BMP to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_BMP

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig

Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl_ddr: Move DDR config options to driver Kconfig

Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.

Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>

powerpc: E500: Move CONFIG_E500 and CONFIG_E500MC to Kconfig

Use Kconfig option for E500 and E500MC macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc85xx: Move CONFIG_FSL_LAW to Kconfig

Some header files have this macro defined conditionally and
redefined unconditionally. Remove all existing definitions.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: MPC8544: Move CONFIG_MPC8544 to Kconfig option

Replace CONFIG_MPC8544 with ARCH_MPC8544 in Kconfig.

Signed-off-by: York Sun <york.sun@nxp.com>

pci: Move CONFIG_PCI_PNP to Kconfig

Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/pci/Kconfig: Add PCI

Add 'PCI' as a menu option and migrate all existing users.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

Convert CONFIG_CONSOLE_EXTRA_INFO to Kconfig

This converts the following to Kconfig:
CONFIG_CONSOLE_EXTRA_INFO

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_VIDEO_SW_CURSOR to Kconfig

This converts the following to Kconfig:
CONFIG_VIDEO_SW_CURSOR

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-convert, find all the cases where this is off]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_VGA_AS_SINGLE_DEVICE to Kconfig

This converts the following to Kconfig:
CONFIG_VGA_AS_SINGLE_DEVICE

Once we migrate to driver model for video, we should be able to drop this
option.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_CFB_CONSOLE to Kconfig

This converts the following to Kconfig:
CONFIG_CFB_CONSOLE

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_VIDEO to Kconfig

This converts the following to Kconfig:
CONFIG_VIDEO

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

common: Add DISPLAY_BOARDINFO

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_USB_STORAGE

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

include/configs: Whitespace fixup

A number of moveconfig.py runs have left a instances of multiple empty
lines in a row. Correct this to a single empty line.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

powerpc: socrates: convert to generic board

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: York Sun <yorksun@freescale.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

powerpc: mpc85xx: move CONFIG_MPC85xx definition to CPU config.mk

Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

kgdb: configs: remove obsolete CONFIG_KGDB_SER_INDEX

The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
care about this parameter or it should be gone completely.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

config: remove platform CONFIG_SYS_HZ definition part 2/2

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Coding Style cleanup: remove trailing white space

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

i2c, fsl_i2c: switch to new multibus/multiadapter support

- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>

i2c, soft-i2c: switch to new multibus/multiadapter support

- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>

pci: introduce CONFIG_PCI_INDIRECT_BRIDGE option

The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.

Introduce a new CONFIG_PCI_INDIRECT_BRIDGE
config option and only compile indirect PCI
bridge support if this options is enabled.

Also add the new option into the configuration
files of the boards which needs that.

Compile tested for powerpc, x86, arm and nds32.
MAKEALL results:

powerpc:
--------------------- SUMMARY ----------------------------
Boards compiled: 641
Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB )
----------------------------------------------------------
Note: the warnings for ELPPC and MPC8323ERDB are present even
without the actual patch.

x86:
--------------------- SUMMARY ----------------------------
Boards compiled: 1
----------------------------------------------------------

arm:
--------------------- SUMMARY ----------------------------
Boards compiled: 311
----------------------------------------------------------

nds32:
--------------------- SUMMARY ----------------------------
Boards compiled: 3
----------------------------------------------------------

Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>

board configs: drop NET_MULTI references

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros

Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE

CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken. Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

powerpc: Cleanup BOOTFLAG_* references

Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Makefile: move all Power Architecture boards into boards.cfg

Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE

The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature

This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

powerpc/85xx: configure autocompletion support

because it's convenient.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

mpc85xx: Add reginfo command

The new command dumps the TLBCAM, the LAWs, and the BR/OR regs.
Add CONFIG_CMD_REGINFO to the config for all MPC85xx parts.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx/socrates: Remove NFS support to fit image size.

This fixes an overflow during the link phase.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>

video: mb862xx: add option VIDEO_FB_16BPP_WORD_SWAP for IPEK01

In 16 bpp mode, the new IPEK01 board only requires swapping of D16 words
for D32 accesses due to the diffferent connecting to the GDC bus. This
patch introduces the configuration option VIDEO_FB_16BPP_WORD_SWAP,
which should be set for all board using the mb862xx in 16 bpp mode. For
the IPEK01, VIDEO_FB_16BPP_PIXEL_SWAP should not be set.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>

video: mb862xx: add option CONFIG_VIDEO_MB862xx_ACCEL for 32bpp mode

The new IPEK01 board can use the 32 bpp mode for the Lime graphics
controller. For this mode, video accelaration does not work. This patch
makes the accelaration configurable via CONFIG_VIDEO_MB862xx_ACCEL,
which is enabled for the lwmon5 and the socrates board for backward
compatibility.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>

video: mb862xx: improve board-specific Lime configuration

To avoid board-specific code accessing the mb862xx registers directly,
the public function mb862xx_probe() has been introduced. Furthermore,
the "Change of Clock Frequency" and "Set Memory I/F Mode" registers
are now defined by CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx__MMR,
respectively. The BSPs for the socrates and lwmon5 boards have been
adapted accordingly.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>

NAND: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...

Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>

i2c: Remove deprecated individual i2c commands

The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.

The functionality of the individual commands is still available via
the 'i2c' command.

This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS

This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Remove unused CONFIG_ADDR_STREAMING defines

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Removed unused CONFIG_L1_INIT_RAM symbol.

Prevent further viral propogation of the unused
symbol CONFIG_L1_INIT_RAM by just removing it.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE references

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

socrates: change default mtest address range

Running mtest command on socrates without specifying
an address range crashes the board. This patch changes
default mtest address range to prevent this behavior.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

socrates: fix SPD EEPROM address

Commit be0bd8234b9777ecd63c4c686f72af070d886517
changed SPD EEPROM address to 0x51 and DDR SDRAM
detection stopped working. Change this address
back to 0x50.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

85xx: socrates: Add support for new image format.

Signed-off-by: Detlev Zundel <dzu@denx.de>

rename CFG_ENV macros to CONFIG_ENV

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

85xx: socrates: Enable Lime support.

This patch adds Lime GDC support together with support for the PWM
backlight control through the w83782d chip. The reset pin of the
latter is attached to GPIO, so we need to reset it in
early_board_init_r.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

85xx: Socrates: Major code update.

- Update the local bus ranges in the FDT for Linux for the various
devices connected to the local bus via chip-select.

- Set the LCRR_DBYP bit in the LCRR for local bus frequencies
lower than 66 MHz and uses I/O accessor functions consequently.

- UPM data update.

- Update of default environment and configuration. Use I2C multibus
as we do have two I2C buses. Also enable sdram and ext2 commands.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>

USB EHCI: reset root hub

Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>

FSL DDR: Convert socrates to new DDR code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

drivers/mtd: Move conditional compilation to Makefile

rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Socrates: NAND support added. Changed the U-Boot base address and

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Socrates: Added FPGA mapping. LAWs and TLBs cleanup.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Socrates: config file cleanup.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Socrates: Fix PCI bus frequency report

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Merge branch 'master' of /home/wd/git/u-boot/custodians

Conflicts:

include/configs/socrates.h

Signed-off-by: Wolfgang Denk <wd@denx.de>

Socrates: Added USB support.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Socrates: add support for DS75 Digital Thermo Sensor on I2C bus.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Socrates: Config file cleanup.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

USB: add support for multiple PCI OHCI controllers

Add new configuration variable CONFIG_PCI_OHCI_DEVNO.
In case of several PCI USB controllers on a board this variable
specifys which controller to use.

Also add USB support for sokrates board.

See doc/README.generic_usb_ohci for details.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>

socrates: fix second TSEC configuration (it is actually TSEC3)

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

socrates: changes to support FDT

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>

Initial support for "Socrates" board

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFG

Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_L2_CACHE to Kconfig

This converts the following to Kconfig:
CONFIG_L2_CACHE

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Remove unused CONFIG symbols

This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM

And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

net: tsec: Remove non-DM_ETH support code

As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPD_EEPROM to Kconfig

This converts the following to Kconfig:
CONFIG_SPD_EEPROM

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_PCI* to CFG_SYS_PCI*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Remove unused symbols

This commit removes the following unused symbols:
CONFIG_SYS_NVRAM_BASE_ADDR
CONFIG_SYS_NVRAM_SIZE
CONFIG_SYS_PAXE_BASE
CONFIG_SYS_PCCNT
CONFIG_SYS_PCDAT
CONFIG_SYS_PCDDR
CONFIG_SYS_PCI1_ADDR
CONFIG_SYS_PCI2_ADDR
CONFIG_SYS_PCI1_IO_BUS
CONFIG_SYS_PCI1_IO_SIZE
CONFIG_SYS_PCI1_MEM_BUS
CONFIG_SYS_PCI1_MEM_SIZE
CONFIG_SYS_PCIE3_ADDR
CONFIG_SYS_PCIE4_ADDR
CONFIG_SYS_PCIE3_IO_PHYS
CONFIG_SYS_PCIE3_IO_VIRT
CONFIG_SYS_PCIE4_IO_PHYS
CONFIG_SYS_PCIE4_IO_VIRT
CONFIG_SYS_PLL_SETTLING_TIME
CONFIG_SYS_QMAN_CENA_BASE
CONFIG_SYS_QMAN_SP_CENA_SIZE
CONFIG_SYS_RCAR_I2C0_BASE
CONFIG_SYS_RCAR_I2C1_BASE
CONFIG_SYS_RCAR_I2C2_BASE
CONFIG_SYS_RCAR_I2C3_BASE
CONFIG_SYS_SATA
CONFIG_SYS_SDRAM_BASE2
CONFIG_SYS_SGMII_REFCLK_MHZ
CONFIG_SYS_SGMII_LINERATE_MHZ
CONFIG_SYS_SGMII_RATESCALE
CONFIG_SYS_SH_SDHI0_BASE
CONFIG_SYS_SH_SDHI0_BASE
CONFIG_SYS_SH_SDHI1_BASE
CONFIG_SYS_SH_SDHI2_BASE
CONFIG_SYS_SH_SDHI3_BASE
CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
CONFIG_SYS_SPI_U_BOOT_SIZE
CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR
CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN
CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT
CONFIG_SYS_VCXK_BASE
CONFIG_SYS_VCXK_DEFAULT_LINEALIGN
CONFIG_SYS_VCXK_DOUBLEBUFFERED
CONFIG_SYS_VCXK_ENABLE_DDR
CONFIG_SYS_VCXK_ENABLE_PIN
CONFIG_SYS_VCXK_ENABLE_PORT
CONFIG_SYS_VCXK_INVERT_DDR
CONFIG_SYS_VCXK_INVERT_PIN
CONFIG_SYS_VCXK_INVERT_PORT
CONFIG_SYS_VCXK_REQUEST_DDR
CONFIG_SYS_VCXK_REQUEST_PIN
CONFIG_SYS_VCXK_REQUEST_PORT
CONFIG_SYS_VSC7385_BR_PRELIM
CONFIG_SYS_VSC7385_OR_PRELIM

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NAND_* to CFG_SYS_NAND_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MAX_NAND_DEVICE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_LOADS_BAUD_CHANGE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_LOADS_BAUD_CHANGE
CONFIG_LOADS_ECHO

As part of this, we move CMD_SAVES to be after CMD_LOADS as they are
logically related (load or save an s-record format file) and this makes
grouping of CONFIG_SYS_LOADS_BAUD_CHANGE easier.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Remove unused symbols CONFIG_SYS_JFFS2_FIRST_BANK et al

This removes the following symbols:
CONFIG_RTC_MCFRRTC
CONFIG_SYS_JFFS2_FIRST_BANK
CONFIG_SYS_JFFS2_FIRST_SECTOR
CONFIG_SYS_JFFS2_NUM_BANKS
CONFIG_SYS_LBC_CACHE_BASE
CONFIG_SYS_LIME_SIZE
CONFIG_SYS_MAMR
CONFIG_SYS_MCFRRTC_BASE
CONFIG_SYS_MONITOR_SEC

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_INIT_RAM_LOCK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_INIT_RAM_LOCK

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Remove CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR et al

This removes the following symbols:
CONFIG_SYS_FSL_DSPI_BE
CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR
CONFIG_SYS_FSL_DSP_CCSR_DDR_OFFSET
CONFIG_SYS_FSL_DSP_DDR_ADDR
CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
CONFIG_SYS_FSL_ERRATUM_A008751
CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
CONFIG_SYS_FSL_ESDHC_NUM
CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK
CONFIG_SYS_FSL_FM1_RX0_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX1_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX2_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX3_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX4_1G_OFFSET
CONFIG_SYS_FSL_FM1_RX5_1G_OFFSET
CONFIG_SYS_FSL_ISBC_VER
CONFIG_SYS_FSL_QSPI_LE
CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR
CONFIG_SYS_FSL_SCFG_IODSECR1_OFFSET
CONFIG_SYS_FSL_SCFG_PIXCLKCR_OFFSET
CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR
CONFIG_SYS_FSL_SRDS_NUM_PLLS
CONFIG_SYS_FSL_WDOG_BE
CONFIG_SYS_GP1DIR
CONFIG_SYS_GP1ODR
CONFIG_SYS_GP2DIR
CONFIG_SYS_GP2ODR
CONFIG_SYS_HALT_BEFOR_RAM_JUMP
CONFIG_SYS_HMI_BASE
FSL_QSPI_FLASH_NUM
FSL_QSPI_FLASH_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_QUIET_TEST to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_QUIET_TEST

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MAX_FLASH_SECT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_FLASH_SECT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_ERASE_TOUT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT

In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_CHECKSUM to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_CHECKSUM

Signed-off-by: Tom Rini <trini@konsulko.com>

usb: ohci-hcd: Remove some unused legacy code

At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USB_OHCI_NEW et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW

Signed-off-by: Tom Rini <trini@konsulko.com>

socrates: Rework CONFIG_PCI_CLK_FREQ

The symbol CONFIG_PCI_CLK_FREQ is local to this board. Provide equal
clarity in the code by referencing the numeric value directly and move
the explanatory comment to the code, just prior to use.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_SPD_BUS_NUM to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPD_BUS_NUM

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENABLE_36BIT_PHYS to Kconfig

This converts the following to Kconfig:
CONFIG_ENABLE_36BIT_PHYS

Signed-off-by: Tom Rini <trini@konsulko.com>

Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>

powerpc: Switch to using CONFIG_SYS_INIT_SP_OFFSET from CONFIG_SYS_GBL_DATA_OFFSET

In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_DIMM_SLOTS_PER_CTLR to Kconfig

This converts the following to Kconfig:
CONFIG_DIMM_SLOTS_PER_CTLR

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ETHPRIME to Kconfig

This converts the following to Kconfig:
CONFIG_ETHPRIME

This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.

Signed-off-by: Tom Rini <trini@konsulko.com>

Remove CONFIG_HAS_ETH0 et al symbols

This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3

This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.

Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CHIP_SELECTS_PER_CTRL to Kconfig

This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL

Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BTB to Kconfig

This converts the following to Kconfig:
CONFIG_BTB

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_TIMESTAMP to Kconfig

This converts the following to Kconfig:
CONFIG_TIMESTAMP

Signed-off-by: Simon Glass <sjg@chromium.org>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_WATCHDOG, HW_WATCHDOG and WDT to Kconfig

Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.

For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.

For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_BR0_PRELIM et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM

This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig

This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>

kgdb: Remove unused serial related options

We have a few CONFIG options for KGDB that are not referenced, remove
them.

Signed-off-by: Tom Rini <trini@konsulko.com>

WS cleanup: remove SPACE(s) followed by TAB

Signed-off-by: Wolfgang Denk <wd@denx.de>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

nxp: Migrate a number of DDR related symbols to Kconfig

- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Remove unused or unnecessary CONFIG symbols related to DDR

These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

treewide: mem: Move mtest related defines to Kconfig

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mpc85xx, socrates: add DM PCI support

add DM PCI support on the socrates board.
use PCIE_FSL now.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: enable DM serial

switch to DM_SERIAL support.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: enable DM I2C

enable DM I2C support for the socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: disable VIDEO

disable video, as not really needed longer.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: add DM support

enable CONFIG_DM for the socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

mpc85xx, socrates: suppress unknown flash warning

suppress warning:
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOT

In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be
defined for each board. To prepare for conversion to Kconfig, add this.

Signed-off-by: Simon Glass <sjg@chromium.org>

rtc: move RTC_RX8025 to Kconfig

move RTC_RX8025 to Kconfig and fixup board configs.

Signed-off-by: Heiko Schocher <hs@denx.de>

configs: fsl: move DDR specific defines to Kconfig

Moves below DDR specific defines to Kconfig:

CONFIG_FSL_DDR_BIST
CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
CONFIG_FSL_DDR_INTERACTIVE
CONFIG_FSL_DDR_SYNC_REFRESH

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MISC_INIT_R to Kconfig

This converts the following to Kconfig:
CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

treewide: Migrate CONFIG_TSEC_ENET to Kconfig

Migrate the CONFIG_TSEC_ENET option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to Kconfig

Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

include/configs: remove numerous CONFIG_SYS_BARGSIZE definitions

This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
equal to CONFIG_SYS_CBSIZE in numerous configuration files.

We remove such definitions in two situations:

- CONFIG_SYS_CBSIZE is otherwise not defined in the board
configuration file, which means the default value of
CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
larger.

- CONFIG_SYS_CBSIZE is defined in the board configuration file, but
to a value equal or less than 512. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
is equal or larger.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_PBSIZE

Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_CMD_REGINFO to Kconfig

This patch converts CONFIG_CMD_REGINFO to Kconfig

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_CMD_PCI to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

configs: Finish migration of PHY_GIGE

Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Convert CONFIG_ENV_IS_IN_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_CMD_EEPROM et al to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>

Drop digital thermometer and thermostat (DTT) drivers

This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

cmd: add Kconfig option for 'date' command

Signed-off-by: Chris Packham <judge.packham@gmail.com>
[trini: default y if DM_RTC, re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_BMP to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_BMP

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig

Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl_ddr: Move DDR config options to driver Kconfig

Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.

Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>

powerpc: E500: Move CONFIG_E500 and CONFIG_E500MC to Kconfig

Use Kconfig option for E500 and E500MC macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc85xx: Move CONFIG_FSL_LAW to Kconfig

Some header files have this macro defined conditionally and
redefined unconditionally. Remove all existing definitions.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: MPC8544: Move CONFIG_MPC8544 to Kconfig option

Replace CONFIG_MPC8544 with ARCH_MPC8544 in Kconfig.

Signed-off-by: York Sun <york.sun@nxp.com>

pci: Move CONFIG_PCI_PNP to Kconfig

Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/pci/Kconfig: Add PCI

Add 'PCI' as a menu option and migrate all existing users.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

Convert CONFIG_CONSOLE_EXTRA_INFO to Kconfig

This converts the following to Kconfig:
CONFIG_CONSOLE_EXTRA_INFO

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_VIDEO_SW_CURSOR to Kconfig

This converts the following to Kconfig:
CONFIG_VIDEO_SW_CURSOR

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-convert, find all the cases where this is off]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_VGA_AS_SINGLE_DEVICE to Kconfig

This converts the following to Kconfig:
CONFIG_VGA_AS_SINGLE_DEVICE

Once we migrate to driver model for video, we should be able to drop this
option.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_CFB_CONSOLE to Kconfig

This converts the following to Kconfig:
CONFIG_CFB_CONSOLE

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_VIDEO to Kconfig

This converts the following to Kconfig:
CONFIG_VIDEO

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

common: Add DISPLAY_BOARDINFO

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_USB_STORAGE

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

include/configs: Whitespace fixup

A number of moveconfig.py runs have left a instances of multiple empty
lines in a row. Correct this to a single empty line.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

powerpc: socrates: convert to generic board

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: York Sun <yorksun@freescale.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

powerpc: mpc85xx: move CONFIG_MPC85xx definition to CPU config.mk

Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

kgdb: configs: remove obsolete CONFIG_KGDB_SER_INDEX

The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
care about this parameter or it should be gone completely.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

config: remove platform CONFIG_SYS_HZ definition part 2/2

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Coding Style cleanup: remove trailing white space

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

i2c, fsl_i2c: switch to new multibus/multiadapter support

- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>

i2c, soft-i2c: switch to new multibus/multiadapter support

- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>

pci: introduce CONFIG_PCI_INDIRECT_BRIDGE option

The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.

Introduce a new CONFIG_PCI_INDIRECT_BRIDGE
config option and only compile indirect PCI
bridge support if this options is enabled.

Also add the new option into the configuration
files of the boards which needs that.

Compile tested for powerpc, x86, arm and nds32.
MAKEALL results:

powerpc:
--------------------- SUMMARY ----------------------------
Boards compiled: 641
Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB )
----------------------------------------------------------
Note: the warnings for ELPPC and MPC8323ERDB are present even
without the actual patch.

x86:
--------------------- SUMMARY ----------------------------
Boards compiled: 1
----------------------------------------------------------

arm:
--------------------- SUMMARY ----------------------------
Boards compiled: 311
----------------------------------------------------------

nds32:
--------------------- SUMMARY ----------------------------
Boards compiled: 3
----------------------------------------------------------

Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>

board configs: drop NET_MULTI references

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros

Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE

CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken. Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

powerpc: Cleanup BOOTFLAG_* references

Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Makefile: move all Power Architecture boards into boards.cfg

Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE

The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>