Convert CONFIG_SYS_MAX_FLASH_SECT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_FLASH_SECT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_EMPTY_INFO to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_EMPTY_INFO

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_CFI_WIDTH to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_CFI_WIDTH

Signed-off-by: Tom Rini <trini@konsulko.com>

mips: octeon: ebb7304: Enable ethernet support

This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:

=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)

Signed-off-by: Stefan Roese <sr@denx.de>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

Signed-off-by: Stefan Roese <sr@denx.de>

Convert CONFIG_SYS_FLASH_CFI_WIDTH to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_CFI_WIDTH

Signed-off-by: Tom Rini <trini@konsulko.com>

mips: octeon: ebb7304: Enable ethernet support

This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:

=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)

Signed-off-by: Stefan Roese <sr@denx.de>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

Signed-off-by: Stefan Roese <sr@denx.de>

mips: octeon: ebb7304: Enable ethernet support

This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:

=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)

Signed-off-by: Stefan Roese <sr@denx.de>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

Signed-off-by: Stefan Roese <sr@denx.de>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

Signed-off-by: Stefan Roese <sr@denx.de>

mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

Signed-off-by: Stefan Roese <sr@denx.de>