global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NAND_* to CFG_SYS_NAND_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_NAND_DBW_8 et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_DBW_8
CONFIG_SYS_NAND_DBW_16

Note that all instances of the code check for CONFIG_SYS_NAND_DBW_16
being defined, and then "else" to CONFIG_SYS_NAND_DBW_8 whereas all of
the configs set CONFIG_SYS_NAND_DBW_8. So we introduce
CONFIG_SYS_NAND_DBW_16 as an option.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MAX_NAND_DEVICE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

video: Drop LCD_BPP

This is used by the old LCD implementation which is to be removed.
Drop it and LCD_OUTPUT_BPP also.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START

We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_BSS_START_ADDR to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_BSS_START_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_PAD_TO et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE

Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_FS_LOAD_PAYLOAD_NAME et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_RAW_ONLY et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_RAW_ONLY
CONFIG_SPL_NAND_SOFTECC

Signed-off-by: Tom Rini <trini@konsulko.com>

include: configs: at91/sam: remove stray #ifdef/#else

With the commit that moves the BOOTCOMMAND to Kconfig:

970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")

some stray ifdefs have been left in the header files which
are now useless.
Clean up the include files to remove these lines.

Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

atmel: Remove CONFIG_SPL_ATMEL_SIZE

This seems to be unused in the code, remove it.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

lcd: Remove LCD_TEST_PATTERN code

This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_LCD_INFO et al to Kconfig

This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ATMEL_LCD et al to Kconfig

This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_RESET_PHY_R to Kconfig

This converts the following to Kconfig:
CONFIG_RESET_PHY_R

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_AT91_WANTS_COMMON_PHY to Kconfig

This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ATMEL_LEGACY to Kconfig

This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

atmel: Remove CONFIG_AT91SAM9G45_LCD_BASE

This variable is used once and is noted as board-specific. Use the
value directly with a comment.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

atmel: Remove CONFIG_AT91SAM9G45EKES

This symbol is used only once, and in comparison with an unset symbol,
so drop it.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig

This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_U_BOOT_LOCATIONS
CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_5_ADDR_CYCLE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_5_ADDR_CYCLE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_PAGE_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_LOAD et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_SPL_NAND_BASE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_BASE
CONFIG_SPL_NAND_IDENT

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE

Signed-off-by: Adam Ford <aford173@gmail.com>

treewide: mem: Move mtest related defines to Kconfig

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NAND_ATMEL to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_ATMEL

Signed-off-by: Adam Ford <aford173@gmail.com>

configs: at91: Adjust CONFIG_ENV_OFFSET to match sama5 address

In order to have a single ENV_OFFSET to manage, use the same as the sama5 one.
This address matches our NAND flash map available at:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com: rework on latest version of u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment

To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

ARM: at91: Remove hardware.h included in configs

As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.

#include <asm/hardware.h>

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

spl: moveconfig: remove SPL_LDSCRIPT definitions for header-files

With the hierarchical defaults set up, we remove these from the header
files. To do so, I've run moveconfig on SPL_LDSCRIPT and this commits
the changes.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

env: Migrate CONFIG_ENV_IS_IN_FAT options to Kconfig

We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_IS_IN_FAT to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FAT

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: at91sam9m10g45ek: Update to support DM/DT

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_WHITE_ON_BLACK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_WHITE_ON_BLACK

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mmc: move CONFIG_GENERIC_MMC to Kconfig

Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.

Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.

I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig

They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.

Anyway, this is the output of the moveconfig tool.

This commit was created as follows:

[1] create a config entry in drivers/mmc/Kconfig

[2] tools/moveconfig.py -r HEAD GENERIC_MMC

[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

mmc: complete unfinished move of CONFIG_MMC

Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.

We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.

I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.

This commit was created as follows:

[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)

[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

spl: Remove CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS

This option isn't used for anything, so get rid of it.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to Kconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Fix sniper and kc1 migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_LCD to Kconfig

This converts the following to Kconfig:
CONFIG_LCD

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

common/Kconfig: Add DISPLAY_CPUINFO

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_NAND_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_MMC_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_GPIO_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_FAT_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Migrate CONFIG_USB_STORAGE

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: atmel: boards: use default CONFIG_SYS_PBSIZE

Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE
into the console and hitting enter afterwards, causes a hang in the
system because CONFIG_SYS_PBSIZE is not capable of storing the extra
characters of the error message:
"Unknown command '' - try 'help'".

Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h
to solve this problem.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>

arm: at91: mpddr: allow multiple DDR controllers

The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).

Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

kconfig: add config option for shell prompt

Add option to set shell prompt string from menuconfig and migrate
boards globally.

The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: atmel: at91sam9m10g45ek: enable spl support

Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.

As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.

Signed-off-by: Bo Shen <voice.shen@atmel.com>

env_fat: use get_device_and_partition() during env save and load

Use get_device_and_partition() is better since:
1. It will call the device initialize function internally. So we can
remove the mmc intialization code to save many lines.
2. It is used by fatls/fatload/fatwrite. So saveenv & load env should
use it too.
3. It can parse the "D:P", "D", "D:", "D:auto" string to get correct
device and partition information by run-time.

Also we remove the FAT_ENV_DEVICE and FAT_ENV_PART. We use a string:
FAT_ENV_DEVICE_AND_PART.
For at91sam9m10g45ek, it is "0". That means use device 0 and if:
a)device 0 has no partition table, use the whole device as a FAT file
system.
b)device 0 has partittion table, use the partition #1.

Refer to the commit: 10a37fd7a4 for details of device & partition string.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

ARM: at91sam9m10g45ek: add mmc environment configuration support

In this configuration the environment will save in file: uboot.env of
mmc card.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: at91sam9m10g45ek: enable mci0 support

Also we enable the mmc command in configuration file.

As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91: remove redundant AT91FAMILY definition in board config file

Now the AT91FAMILY is already defined in the at91 SoC header. The at91
board config file will include the SoC header file.

So we can remove the redundant AT91FAMILY definition in at91 board
config files.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: at91sam9m10g45ek: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: atmel: sam9m10g45ek: let CONFIG_SYS_NO_FLASH at proper position

In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.

So move CONFIG_SYS_NO_FLASH definition to proper position.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm926ejs, at91: add common phy_reset function

add common phy reset code into a common function.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Jens Scharsig <esw@bus-elektronik.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Markus Hubig <mhubig@imko.de>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91sam9m10g45ek: remove unused CONFIG_AT91_LEGACY

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>

config: remove platform CONFIG_SYS_HZ definition part 2/2

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

arm: atmel: remove the config.mk file

remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

ARM: at91: change nand flash table

Change nand flash partition table according to www.at91.com/linux4sam

more information: http://www.at91.com/linux4sam/bin/view/Linux4SAM/GettingStarted#Linux4SAM_NandFlash_demo_Memory

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[minor commit message changes]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: at91/configs: add bootz to configuration

Support to boot zImage

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Add bootz for at91rm9200, at91sam9263, at91sam9rl]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Atmel: sam9g10/9m10/9x5: Add support to boot DT kernel

The mainline linux kernel is moving to flatten device tree support
Add the CONFIG_OF_LIBFDT option to support booting DT linux kernel

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: sam9g10/sam9m10g45: remove CONFIG_ARCH_CPU_INIT

Remove CONFIG_ARCH_CPU_INIT for at91sam9g10ek and at91sam9m10g45ek

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: Remove unused stack and irq config defines

CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.

IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

AT91: at91sam9m10g45ek : Enable EHCI instead OHCI

Enable EHCI support instead OHCI

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>

CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>

CMD: Remove CMD_AUTOSCRIPT, it's not used

$ git grep AUTOSCRIPT
include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT
include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPT

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Anatolij Gustschin <agust@denx.de>

NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS

NAND_MAX_CHIPS has been replaced by CONFIG_SYS_NAND_MAX_CHIPS,
and the latter defaults to 1.

Signed-off-by: Scott Wood <scottwood@freescale.com>

Fix Stelian's email address

Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

board configs: drop NET_MULTI references

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

atmel: Update support of board AT91SAM9M10G45-EK to new style

Based on earlier work by Alex Waterman <awaterman@dawning.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

Drop support for CONFIG_SKIP_RELOCATE_UBOOT

For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().

With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

ARM change name of defines for AT91 arm926ejs

Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:

AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK

Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>

add a new AT91 GPIO driver

* add a real AT91 GPIO driver instead of header inline code
* resolve the mixing of port and pins
* change board config files to use new driver
* add macros to gpio to realize backward compatibility

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>

add new CONFIG_AT91_LEGACY

* add's the new temporary CONFIG_AT91_LEGACY to all board configs
This will need for backward compatiblity, while change the SoC access
to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated
SoC is used.

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>

common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>

Update the mtd driver name in bootargs for at91-based boards

The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>

AT91: factor out ROUND() macro

A large number of boards (all AT91 based) duplicated the ROUND()
macro in their board specific config files. Add the definition to
include/common.h and clean up the board config files.

Signed-off-by: Wolfgang Denk <wd@denx.de>

NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...

Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.

This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).

Signed-off-by: Wolfgang Denk <wd@denx.de>

at91: Introduction of at91sam9g45 SOC.

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MAX_NAND_DEVICE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

video: Drop LCD_BPP

This is used by the old LCD implementation which is to be removed.
Drop it and LCD_OUTPUT_BPP also.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START

We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_BSS_START_ADDR to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_BSS_START_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_PAD_TO et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE

Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_FS_LOAD_PAYLOAD_NAME et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_RAW_ONLY et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_RAW_ONLY
CONFIG_SPL_NAND_SOFTECC

Signed-off-by: Tom Rini <trini@konsulko.com>

include: configs: at91/sam: remove stray #ifdef/#else

With the commit that moves the BOOTCOMMAND to Kconfig:

970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")

some stray ifdefs have been left in the header files which
are now useless.
Clean up the include files to remove these lines.

Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

atmel: Remove CONFIG_SPL_ATMEL_SIZE

This seems to be unused in the code, remove it.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

lcd: Remove LCD_TEST_PATTERN code

This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_LCD_INFO et al to Kconfig

This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ATMEL_LCD et al to Kconfig

This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_RESET_PHY_R to Kconfig

This converts the following to Kconfig:
CONFIG_RESET_PHY_R

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_AT91_WANTS_COMMON_PHY to Kconfig

This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ATMEL_LEGACY to Kconfig

This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

atmel: Remove CONFIG_AT91SAM9G45_LCD_BASE

This variable is used once and is noted as board-specific. Use the
value directly with a comment.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

atmel: Remove CONFIG_AT91SAM9G45EKES

This symbol is used only once, and in comparison with an unset symbol,
so drop it.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig

This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_U_BOOT_LOCATIONS
CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_5_ADDR_CYCLE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_5_ADDR_CYCLE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_PAGE_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_LOAD et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_SPL_NAND_BASE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_BASE
CONFIG_SPL_NAND_IDENT

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE

Signed-off-by: Adam Ford <aford173@gmail.com>

treewide: mem: Move mtest related defines to Kconfig

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NAND_ATMEL to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_ATMEL

Signed-off-by: Adam Ford <aford173@gmail.com>

configs: at91: Adjust CONFIG_ENV_OFFSET to match sama5 address

In order to have a single ENV_OFFSET to manage, use the same as the sama5 one.
This address matches our NAND flash map available at:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com: rework on latest version of u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment

To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

ARM: at91: Remove hardware.h included in configs

As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.

#include <asm/hardware.h>

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

spl: moveconfig: remove SPL_LDSCRIPT definitions for header-files

With the hierarchical defaults set up, we remove these from the header
files. To do so, I've run moveconfig on SPL_LDSCRIPT and this commits
the changes.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

env: Migrate CONFIG_ENV_IS_IN_FAT options to Kconfig

We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_IS_IN_FAT to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FAT

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: at91sam9m10g45ek: Update to support DM/DT

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_WHITE_ON_BLACK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_WHITE_ON_BLACK

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mmc: move CONFIG_GENERIC_MMC to Kconfig

Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.

Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.

I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig

They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.

Anyway, this is the output of the moveconfig tool.

This commit was created as follows:

[1] create a config entry in drivers/mmc/Kconfig

[2] tools/moveconfig.py -r HEAD GENERIC_MMC

[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

mmc: complete unfinished move of CONFIG_MMC

Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.

We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.

I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.

This commit was created as follows:

[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)

[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

spl: Remove CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS

This option isn't used for anything, so get rid of it.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to Kconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Fix sniper and kc1 migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_LCD to Kconfig

This converts the following to Kconfig:
CONFIG_LCD

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

common/Kconfig: Add DISPLAY_CPUINFO

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_NAND_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_MMC_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_GPIO_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_FAT_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Migrate CONFIG_USB_STORAGE

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: atmel: boards: use default CONFIG_SYS_PBSIZE

Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE
into the console and hitting enter afterwards, causes a hang in the
system because CONFIG_SYS_PBSIZE is not capable of storing the extra
characters of the error message:
"Unknown command '' - try 'help'".

Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h
to solve this problem.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>

arm: at91: mpddr: allow multiple DDR controllers

The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).

Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

kconfig: add config option for shell prompt

Add option to set shell prompt string from menuconfig and migrate
boards globally.

The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: atmel: at91sam9m10g45ek: enable spl support

Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.

As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.

Signed-off-by: Bo Shen <voice.shen@atmel.com>

env_fat: use get_device_and_partition() during env save and load

Use get_device_and_partition() is better since:
1. It will call the device initialize function internally. So we can
remove the mmc intialization code to save many lines.
2. It is used by fatls/fatload/fatwrite. So saveenv & load env should
use it too.
3. It can parse the "D:P", "D", "D:", "D:auto" string to get correct
device and partition information by run-time.

Also we remove the FAT_ENV_DEVICE and FAT_ENV_PART. We use a string:
FAT_ENV_DEVICE_AND_PART.
For at91sam9m10g45ek, it is "0". That means use device 0 and if:
a)device 0 has no partition table, use the whole device as a FAT file
system.
b)device 0 has partittion table, use the partition #1.

Refer to the commit: 10a37fd7a4 for details of device & partition string.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

ARM: at91sam9m10g45ek: add mmc environment configuration support

In this configuration the environment will save in file: uboot.env of
mmc card.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: at91sam9m10g45ek: enable mci0 support

Also we enable the mmc command in configuration file.

As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91: remove redundant AT91FAMILY definition in board config file

Now the AT91FAMILY is already defined in the at91 SoC header. The at91
board config file will include the SoC header file.

So we can remove the redundant AT91FAMILY definition in at91 board
config files.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: at91sam9m10g45ek: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: atmel: sam9m10g45ek: let CONFIG_SYS_NO_FLASH at proper position

In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.

So move CONFIG_SYS_NO_FLASH definition to proper position.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm926ejs, at91: add common phy_reset function

add common phy reset code into a common function.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Jens Scharsig <esw@bus-elektronik.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Markus Hubig <mhubig@imko.de>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91sam9m10g45ek: remove unused CONFIG_AT91_LEGACY

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>

config: remove platform CONFIG_SYS_HZ definition part 2/2

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

arm: atmel: remove the config.mk file

remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

ARM: at91: change nand flash table

Change nand flash partition table according to www.at91.com/linux4sam

more information: http://www.at91.com/linux4sam/bin/view/Linux4SAM/GettingStarted#Linux4SAM_NandFlash_demo_Memory

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[minor commit message changes]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: at91/configs: add bootz to configuration

Support to boot zImage

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Add bootz for at91rm9200, at91sam9263, at91sam9rl]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Atmel: sam9g10/9m10/9x5: Add support to boot DT kernel

The mainline linux kernel is moving to flatten device tree support
Add the CONFIG_OF_LIBFDT option to support booting DT linux kernel

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: sam9g10/sam9m10g45: remove CONFIG_ARCH_CPU_INIT

Remove CONFIG_ARCH_CPU_INIT for at91sam9g10ek and at91sam9m10g45ek

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: Remove unused stack and irq config defines

CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.

IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

AT91: at91sam9m10g45ek : Enable EHCI instead OHCI

Enable EHCI support instead OHCI

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>

CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>

CMD: Remove CMD_AUTOSCRIPT, it's not used

$ git grep AUTOSCRIPT
include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT
include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPT

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Anatolij Gustschin <agust@denx.de>

NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS

NAND_MAX_CHIPS has been replaced by CONFIG_SYS_NAND_MAX_CHIPS,
and the latter defaults to 1.

Signed-off-by: Scott Wood <scottwood@freescale.com>

Fix Stelian's email address

Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

board configs: drop NET_MULTI references

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

atmel: Update support of board AT91SAM9M10G45-EK to new style

Based on earlier work by Alex Waterman <awaterman@dawning.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

Drop support for CONFIG_SKIP_RELOCATE_UBOOT

For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().

With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

ARM change name of defines for AT91 arm926ejs

Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:

AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK

Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>

add a new AT91 GPIO driver

* add a real AT91 GPIO driver instead of header inline code
* resolve the mixing of port and pins
* change board config files to use new driver
* add macros to gpio to realize backward compatibility

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>

add new CONFIG_AT91_LEGACY

* add's the new temporary CONFIG_AT91_LEGACY to all board configs
This will need for backward compatiblity, while change the SoC access
to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated
SoC is used.

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>

common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>

Update the mtd driver name in bootargs for at91-based boards

The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>

AT91: factor out ROUND() macro

A large number of boards (all AT91 based) duplicated the ROUND()
macro in their board specific config files. Add the definition to
include/common.h and clean up the board config files.

Signed-off-by: Wolfgang Denk <wd@denx.de>

NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...

Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.

This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).

Signed-off-by: Wolfgang Denk <wd@denx.de>

at91: Introduction of at91sam9g45 SOC.

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>

video: Drop LCD_BPP

This is used by the old LCD implementation which is to be removed.
Drop it and LCD_OUTPUT_BPP also.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START

We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_BSS_START_ADDR to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_BSS_START_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_PAD_TO et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE

Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_FS_LOAD_PAYLOAD_NAME et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_RAW_ONLY et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_RAW_ONLY
CONFIG_SPL_NAND_SOFTECC

Signed-off-by: Tom Rini <trini@konsulko.com>

include: configs: at91/sam: remove stray #ifdef/#else

With the commit that moves the BOOTCOMMAND to Kconfig:

970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")

some stray ifdefs have been left in the header files which
are now useless.
Clean up the include files to remove these lines.

Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

atmel: Remove CONFIG_SPL_ATMEL_SIZE

This seems to be unused in the code, remove it.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

lcd: Remove LCD_TEST_PATTERN code

This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_LCD_INFO et al to Kconfig

This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ATMEL_LCD et al to Kconfig

This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_RESET_PHY_R to Kconfig

This converts the following to Kconfig:
CONFIG_RESET_PHY_R

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_AT91_WANTS_COMMON_PHY to Kconfig

This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ATMEL_LEGACY to Kconfig

This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

atmel: Remove CONFIG_AT91SAM9G45_LCD_BASE

This variable is used once and is noted as board-specific. Use the
value directly with a comment.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

atmel: Remove CONFIG_AT91SAM9G45EKES

This symbol is used only once, and in comparison with an unset symbol,
so drop it.

Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig

This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_U_BOOT_LOCATIONS
CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_5_ADDR_CYCLE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_5_ADDR_CYCLE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_PAGE_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_LOAD et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_SPL_NAND_BASE et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_BASE
CONFIG_SPL_NAND_IDENT

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE

Signed-off-by: Adam Ford <aford173@gmail.com>

treewide: mem: Move mtest related defines to Kconfig

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NAND_ATMEL to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_ATMEL

Signed-off-by: Adam Ford <aford173@gmail.com>

configs: at91: Adjust CONFIG_ENV_OFFSET to match sama5 address

In order to have a single ENV_OFFSET to manage, use the same as the sama5 one.
This address matches our NAND flash map available at:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com: rework on latest version of u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment

To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

ARM: at91: Remove hardware.h included in configs

As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.

#include <asm/hardware.h>

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

spl: moveconfig: remove SPL_LDSCRIPT definitions for header-files

With the hierarchical defaults set up, we remove these from the header
files. To do so, I've run moveconfig on SPL_LDSCRIPT and this commits
the changes.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

env: Migrate CONFIG_ENV_IS_IN_FAT options to Kconfig

We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_IS_IN_FAT to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FAT

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: at91sam9m10g45ek: Update to support DM/DT

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_WHITE_ON_BLACK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_WHITE_ON_BLACK

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mmc: move CONFIG_GENERIC_MMC to Kconfig

Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.

Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.

I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig

They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.

Anyway, this is the output of the moveconfig tool.

This commit was created as follows:

[1] create a config entry in drivers/mmc/Kconfig

[2] tools/moveconfig.py -r HEAD GENERIC_MMC

[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>