net: phy: motorcomm: Add support for YT8511 PHY

The YT8511 ethernet PHYs can be found on e.g. the SOQuartz or
the Quartz64. Add rudimentary support for them.

Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>

net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy

Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on StarFive VisionFive2 board.

Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux

Pull Marvell 10G PHY driver from Linux 6.1.y as of commit
d6d29292640d3 ("net: phy: marvell10g: select host interface configuration")
and heavily adapt to match U-Boot PHY framework. Support for
hwmon is removed as is much other functionality which could
not be tested, this results in much simpler driver which can
only bring the PHY up and set MAC type.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Add an SPL config for atheros

Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split
config.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS

Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Remove extraneous dependencies

With DM_ETH being required now for all drivers, we don't need this
listed on individual drivers as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

phy: add driver for Intel XWAY PHY

Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

net: phy: Add support for TI PHY init

ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

phy: Add support for the NC-SI protocol

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: fix switch vendor name

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add gmiitorgmii converter support

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: realtek: Introduce quirk to mark RXC not stoppable

When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: aquantia: add firmware loading support

Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: migrate CONFIG_PHY_AQUANTIA to Kconfig

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Don't limit phy addresses by default

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move CONFIG_PHY_ADDR to Kconfig

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.

- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.

- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Kconfig: net: phylib: Phylib should depends on NET

There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add Broadcom BCM53xx switch driver

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

net: phy: Add Amlogic Meson GXL Internal PHY support

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Merge git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/net/phy: add fixed-phy / fixed-link support

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

drivers: net: phy: add MV88E6xx options to Kconfig

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Provide Kconfig menu for PHYLIB

Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy

Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on StarFive VisionFive2 board.

Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux

Pull Marvell 10G PHY driver from Linux 6.1.y as of commit
d6d29292640d3 ("net: phy: marvell10g: select host interface configuration")
and heavily adapt to match U-Boot PHY framework. Support for
hwmon is removed as is much other functionality which could
not be tested, this results in much simpler driver which can
only bring the PHY up and set MAC type.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Add an SPL config for atheros

Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split
config.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS

Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Remove extraneous dependencies

With DM_ETH being required now for all drivers, we don't need this
listed on individual drivers as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

phy: add driver for Intel XWAY PHY

Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

net: phy: Add support for TI PHY init

ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

phy: Add support for the NC-SI protocol

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: fix switch vendor name

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add gmiitorgmii converter support

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: realtek: Introduce quirk to mark RXC not stoppable

When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: aquantia: add firmware loading support

Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: migrate CONFIG_PHY_AQUANTIA to Kconfig

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Don't limit phy addresses by default

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move CONFIG_PHY_ADDR to Kconfig

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.

- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.

- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Kconfig: net: phylib: Phylib should depends on NET

There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add Broadcom BCM53xx switch driver

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

net: phy: Add Amlogic Meson GXL Internal PHY support

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Merge git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/net/phy: add fixed-phy / fixed-link support

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

drivers: net: phy: add MV88E6xx options to Kconfig

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Provide Kconfig menu for PHYLIB

Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux

Pull Marvell 10G PHY driver from Linux 6.1.y as of commit
d6d29292640d3 ("net: phy: marvell10g: select host interface configuration")
and heavily adapt to match U-Boot PHY framework. Support for
hwmon is removed as is much other functionality which could
not be tested, this results in much simpler driver which can
only bring the PHY up and set MAC type.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Add an SPL config for atheros

Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split
config.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS

Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Remove extraneous dependencies

With DM_ETH being required now for all drivers, we don't need this
listed on individual drivers as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

phy: add driver for Intel XWAY PHY

Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

net: phy: Add support for TI PHY init

ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

phy: Add support for the NC-SI protocol

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: fix switch vendor name

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add gmiitorgmii converter support

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: realtek: Introduce quirk to mark RXC not stoppable

When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: aquantia: add firmware loading support

Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: migrate CONFIG_PHY_AQUANTIA to Kconfig

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Don't limit phy addresses by default

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move CONFIG_PHY_ADDR to Kconfig

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.

- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.

- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Kconfig: net: phylib: Phylib should depends on NET

There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add Broadcom BCM53xx switch driver

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

net: phy: Add Amlogic Meson GXL Internal PHY support

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Merge git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/net/phy: add fixed-phy / fixed-link support

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

drivers: net: phy: add MV88E6xx options to Kconfig

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Provide Kconfig menu for PHYLIB

Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS

Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: Remove extraneous dependencies

With DM_ETH being required now for all drivers, we don't need this
listed on individual drivers as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

phy: add driver for Intel XWAY PHY

Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

net: phy: Add support for TI PHY init

ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

phy: Add support for the NC-SI protocol

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: fix switch vendor name

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add gmiitorgmii converter support

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: realtek: Introduce quirk to mark RXC not stoppable

When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: aquantia: add firmware loading support

Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: migrate CONFIG_PHY_AQUANTIA to Kconfig

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Don't limit phy addresses by default

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move CONFIG_PHY_ADDR to Kconfig

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.

- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.

- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Kconfig: net: phylib: Phylib should depends on NET

There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add Broadcom BCM53xx switch driver

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

net: phy: Add Amlogic Meson GXL Internal PHY support

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Merge git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/net/phy: add fixed-phy / fixed-link support

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

drivers: net: phy: add MV88E6xx options to Kconfig

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Provide Kconfig menu for PHYLIB

Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: Remove extraneous dependencies

With DM_ETH being required now for all drivers, we don't need this
listed on individual drivers as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

phy: add driver for Intel XWAY PHY

Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

net: phy: Add support for TI PHY init

ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

phy: Add support for the NC-SI protocol

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: fix switch vendor name

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add gmiitorgmii converter support

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: realtek: Introduce quirk to mark RXC not stoppable

When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: aquantia: add firmware loading support

Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: migrate CONFIG_PHY_AQUANTIA to Kconfig

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Don't limit phy addresses by default

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move CONFIG_PHY_ADDR to Kconfig

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.

- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.

- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Kconfig: net: phylib: Phylib should depends on NET

There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add Broadcom BCM53xx switch driver

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

net: phy: Add Amlogic Meson GXL Internal PHY support

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Merge git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/net/phy: add fixed-phy / fixed-link support

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

drivers: net: phy: add MV88E6xx options to Kconfig

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Provide Kconfig menu for PHYLIB

Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

phy: add driver for Intel XWAY PHY

Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

net: phy: Add support for TI PHY init

ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>

phy: Add support for the NC-SI protocol

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: fix switch vendor name

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add gmiitorgmii converter support

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: realtek: Introduce quirk to mark RXC not stoppable

When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: aquantia: add firmware loading support

Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: migrate CONFIG_PHY_AQUANTIA to Kconfig

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Don't limit phy addresses by default

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move CONFIG_PHY_ADDR to Kconfig

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.

- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.

- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Kconfig: net: phylib: Phylib should depends on NET

There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add Broadcom BCM53xx switch driver

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

net: phy: Add Amlogic Meson GXL Internal PHY support

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Merge git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/net/phy: add fixed-phy / fixed-link support

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

drivers: net: phy: add MV88E6xx options to Kconfig

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: Provide Kconfig menu for PHYLIB

Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_FSL_MEMAC et al to Kconfig

This converts the following to Kconfig:
CONFIG_FSL_MEMAC
CONFIG_SYS_MEMAC_LITTLE_ENDIAN

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

phy: adin: add driver for Analog Devices ADIN1300 PHY

The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Convert CONFIG_BITBANGMII_MULTI to Kconfig

This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_PHY_RESET_DELAY to Kconfig

This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

net: phy: Add support for ethernet-phy-id with gpio reset

Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: realtek: Add tx/rx delay config for 8211e

Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.

In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.

Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).

This removes the need for a one-off workaround for the Pine A64+ board.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Kconfig: Remove all default n/no options

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

phy: add nxp tja1103 phy driver

Add nxp tja1103 phy driver.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: ca_phy: Add driver for CAxxxx SoCs

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

net: phy: Add DP8382x phy registration to TI PHY init

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>