mtd: nand: Add core infrastructure to support SPI NANDs

Add a SPI NAND framework based on the generic NAND framework and the
spi-mem infrastructure.

In its current state, this framework supports the following features:

- single/dual/quad IO modes
- on-die ECC

Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>

mtd: nand: Add core infrastructure to deal with NAND devices

Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>

mtd: move NAND files into a raw/ subdirectory

NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Convert CONFIG_NAND_DAVINCI to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_DAVINCI

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_NAND_ATMEL to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_ATMEL

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_NAND_LPC32XX_SLC to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_LPC32XX_SLC

Signed-off-by: Adam Ford <aford173@gmail.com>

mtd: nand: mxs_nand: add device tree support

Support driver data from device tree. Also support fsl,use-minimal-ecc
similar to Linux' GPMI NAND driver.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

mtd: nand: mxs_nand: add minimal ECC support

Add support for minimum ECC strength supported by the NAND chip.
This aligns with the behavior when using the fsl,use-minimum-ecc
device tree property in Linux.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

mtd: nand: mxs_nand: use self init

Instead of completing initialization via scan_bbt callback use
NAND self init to initialize the GPMI (MXS) NAND controller.

Suggested-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

sunxi: move the NAND parameters to Kconfig

Move the NAND parameters from defconfig files to Kconfig for SUNXI
architecture only. Fort now only the CHIP pro is migrated.

It would have been better to convert this defconfig entry to Kconfig for
all supported machines/architectures but it has been abandoned due to a
fairly high amount of errors reported by the moveconfig.py tool. This is
due to defines quite often being multiplications of values/other defines
not correctly handled.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

sunxi: make NAND_SUNXI use ARCH_SUNXI as default in Kconfig

Remove NAND_SUNXI from the CHIP pro defconfig to be automatically
selected depending on the state of ARCH_SUNXI.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

sunxi: automatically select SPL_NAND_SUPPORT in Kconfig

Make SUNXI_NAND select SPL_NAND_SUPPORT in Kconfig, this limit the
number of entries to add in defconfig files when adding NAND support.

For now, the only board using it is the CHIP pro.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

sunxi: allow NAND support to be compiled for sun8i platforms

Add some clocks/PLL definitions as well as the dependency on MACH_SUN8I
in Kconfig.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Convert CONFIG_APBH_DMA et al to Kconfig

This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NAND_MXS to Kconfig

This converts CONFIG_NAND_MXS to Kconfig.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

nand: arasan: Select CONFIG_SYS_NAND_SELF_INIT

The Arasan NFC driver requires the self-init mode,
so it should select it.

Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mtd: nand: denali: make NAND_DENALI unconfigurable option

denali.c has no driver entry in itself. It makes sense only when
compiled together with denali_dt.c

Let NAND_DENALI_DT select NAND_DENALI, and hide NAND_DENALI from
the Kconfig menu.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mtd: nand: denali: sync with Linux 4.15-rc1

I largely reworked the Denali NAND controller driver in Linux.
This commit imports the improvements from Linux. The code is
almost synced with Linux 4.15-rc1.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mtd: nand: zynq: Add a config option to use 1st stage bootloader timing

In legacy method, 1st stage bootloader was used to configure the HW
setting such as NAND timing. Hence, adding a config option in Zynq
NAND driver for the compatibility of device that using 1st stage
bootloder instead of U-boot SPL.

This commit is to add config option
CONFIG_NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS that allow NAND driver use
timing values set by the 1st stage bootloader, instead of the hard-coded
values in the Zynq NAND driver.

Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

omap2: nand: Make NAND_OMAP_GPMC_PREFETCH default

This option provides better performance and should really always be
enabled. Make this be default y.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>

Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>

mtd: nand: denali_dt: add a DT driver

A patch for NAND uclass support was proposed about half a year ago:
https://patchwork.ozlabs.org/patch/722282/

It was not merged and I do not see on-going work for this.

Without DM-based probing, we need to set up pinctrl etc. in an ad-hoc
way and give lots of crappy CONFIG options for base addresses and
properties, which are supposed to be specified by DT. This is painful.

This commit just provides a probe hook to retrieve "reg" from DT and
allocate private data in a DM manner. This DT driver is not essentially
a NAND driver, in fact it is (ab)using UCLASS_MISC. Once UCLASS_NAND is
supported, it would be possible to migrate to it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Convert CONFIG_NAND to Kconfig

This converts the following to Kconfig:
CONFIG_NAND

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Sync up a few more, add imply's]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x

There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>

nand: sunxi: Add options for the SPL NAND configuration

The SPL image needs to be built with a different ECC configuration than the
U-Boot binary.

Add Kconfig options with defaults to provide a value that should work for
anyone, but is still configurable if needs be.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mtd: sunxi: Change U-Boot offset

The default U-Boot offset for the Allwinner SoCs was set to 32kB.

This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.

However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).

We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.

It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.

Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mtd: sunxi: Select the U-Boot location config option

We'll need that symbol so that the default offset are defined

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mtd: nand: build MXS driver for MX7 as well

The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).

Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.

Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>

mtd: nand: zynq_nand: Add nand driver support for zynq

Add nand flash controller driver support for zynq SoC.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mtd: nand: Kconfig: Add NAND_MXS entry

Added kconfig for NAND_MXS driver.

Cc: Scott Wood <oss@buserror.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

mtd: nand: Add the sunxi NAND controller driver

We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.

The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

spl: nand: support redundant u-boot image

On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.

Add an extra Kconfig option to specify the offset of the redundant u-boot
image.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>

spl: nand: rework SYS_NAND_U_BOOT_OFFS Kconfig option dependency

The SYS_NAND_U_BOOT_OFFS is quite generic, but the Kconfig entry is forced
to explicitly depend on platforms that are not already defining it in their
include/configs/<board>.h header.

Add the SYS_NAND_U_BOOT_LOCATIONS option, make the SYS_NAND_U_BOOT_OFFS
depends on it, remove the dependency on NAND_SUNXI and make it dependent
on SPL selection.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

zynqmp: nand: Add Nand driver support for zynqmp

Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>

mtd: nand: Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig

Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.

Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>

sunxi_nand_spl: Remove NAND_SUNXI_SPL_SYNDROME_PARTITIONS_END

We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.

Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.

Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXI

We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.

Renaming the Kconfig option now makes things easier when we add full
nand support in the future.

The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi_nand_spl: Auto detect nand configuration parameters

Auto detect the nand configuration parameters, like the BROM does.

This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.

The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.

Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi_nand_spl: Add support for sun4i and sun5i SoCs

Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.

Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessary

Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

mtd: nand: Add mvebu (PXA / AXP / A38x) NAND device driver

Cloned from the Linux driver v4.2.0-rc2. Plus some patches from
Antoine Tenart enabling controller initialization and ONFI timing
support:

http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html

Please note that this driver needs the Linux NAND subsystem sync to v4.1
from Scott to be applied:

https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html

Otherwise it will not compile.

Tested on the Marvell Armada XP DB-MV784MP-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>

sunxi: nand: Add board configuration options

When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.

This commit also introduces the configurable options in Kconfig.

Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

mtd: vf610_nfc: add 32-error correction option for HW ECC

Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).

Signed-off-by: Stefan Agner <stefan@agner.ch>

mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig

This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>

kconfig: remove unneeded dependency on !SPL_BUILD

Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

kconfig: switch to single .config configuration

When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL). There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.

It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:

[1] It is impossible to share CONFIG options across the images.
If you change the configuration of Main image, you often have to
adjust some SPL configurations correspondingly. Currently, we
cannot handle the dependencies between them. It means one of the
biggest advantages of Kconfig is lost.

[2] It is too painful to change both ".config" and "spl/.config".
Sunxi guys started to work around this problem by creating a new
configuration target. Commit cbdd9a9737cc (sunxi: kconfig: Add
%_felconfig rule to enable FEL build of sunxi platforms.) added
"make *_felconfig" to enable CONFIG_SPL_FEL on both images.
Changing the configuration of multiple images in one command is a
generic demand. The current implementation cannot propose any
good solution about this.

[3] Kconfig files are getting ugly and difficult to understand.
Commit b724bd7d6349 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.

[4] The build system got more complicated than it should be.
To adjust Linux-originated Kconfig to U-Boot, the helper script
"scripts/multiconfig.sh" was introduced. Writing a complicated
text processor is a shell script sometimes caused problems.

Now I believe the "single .config" will serve us better. With it,
all the problems above would go away. Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much. Anyway, this is what we do now in
scripts/Makefile.spl.

I admit my mistake with my apology and this commit switches to the
single .config configuration.

It is not so difficult to do that:

- Remove unnecessary processings from scripts/multiconfig.sh
This file will remain for a while to support the current defconfig
format. It will be removed after more cleanups are done.

- Adjust some makefiles and Kconfigs

- Add some entries to include/config_uncmd_spl.h and the new file
scripts/Makefile.uncmd_spl. Some CONFIG options that are not
supported on SPL must be disabled because one .config is shared
between SPL and U-Boot proper going forward. I know this is not
a beautiful solution and I think we can do better, but let's see
how much we will have to describe them.

- update doc/README.kconfig

More cleaning up patches will follow this.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mtd: denali: use CONFIG_SYS_NAND_SELF_INIT

Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().

CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail(). It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux. Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>

mtd: denali: add Denali NAND driver for SPL

The SPL-mode driver for Denali(Cadence) NAND Flash Memory Controller IP.

This driver requires two CONFIG macros:
- CONFIG_SPL_NAND_DENALI
Define to enable this driver.
- CONFIG_SYS_NAND_BAD_BLOCK_POS
Specify bad block mark position in the oob space. Typically 0.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>

mtd: denali: add Denali controller configs to Kconfig

Commit 3eb3e72a3f66 (nand/denali: Adding Denali NAND driver support)
introduced some new options, and some of them were documented by
commit f9860cf081ef (nand/denali: Document CONFIG symbols).

This commit allows users to enable/disable them via Kconfig
with more detailed help docs.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>