Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Remove <common.h> and add needed includes

Remove <common.h> from this driver directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Finish CONFIG -> CFG migration

At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace

Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Make bank_addr_bits reflect actual bits

In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.

There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.

Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ppc: Remove MPC8555CDS boards

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ppc: Remove MPC8541CDS board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

common: Drop linux/bitops.h from common header

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: Drop log.h from common header

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "drivers/ddr/fsl: Dual-license DDR driver"

Upon further review, not all code authors are in favour of this change.
This reverts commit ee3556bcafbb05e59aabdc31368984e76acaabc4.

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/ddr/fsl: Dual-license DDR driver

To make this driver easier to be reused, dual-license DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/ddr/fsl: Add calculation of register control words

DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Add 3DS RDIMM support

On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Fix DDR4 RDIMM support

For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.

Signed-off-by: York Sun <york.sun@nxp.com>

common: arm: freescale: layerscape: Move header files out of common.h

We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: freescale: Move arch-specific declarations

The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS

These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl/ddr: Add erratum_a009942_check_cpo and clean related erratum

- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>

powerpc: MPC8555: Remove macro CONFIG_MPC8555

Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc8541: Remove macro CONFIG_MPC8541

Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Fix timing_cfg_2

Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>

Various, unrelated tree-wide typo fixes.

Fix a number of typos, including:

* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

drivers/ddr/fsl: Fix timing_cfg_2 register

Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl

The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete

Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Update timing config for heavy load

In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update MR5 RTT park

For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update DDR4 MR6 for Vref range

MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl_ddr: Make SR_IE configurable

SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix driver to support empty first slot

CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl: Update DDR driver for DDR4

Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.

Signed-off-by: York Sun <yorksun@freescale.com>

MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT register

According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.

>From section 9.4.1.8 of that manual:

Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.

0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.

In addition, Freescale application note AN2805 is also very clear that
this bit must be set.

This patch reverts a change introduced by commit
457caecdbca3df21a93abff19eab12dbc61b7897.

Testing Done:

Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:

fff9b774: 65 29 80 00 oris r9,r9,32768

Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.

Booted an image on a MPC8541 based board successfully.

Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix a typo in timing_cfg_8 calculation

wwt_bg should match rrt_bg. It was a typo in driver.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support for multiple DDR clocks

Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust CAS to preamble override for emulator

On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.

These should be set before MEM_EN is set.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix MRC_CYC calculation for DDR3

For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.

DDR4 is not affected by this change.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots

Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>

linux/kernel.h: sync min, max, min3, max3 macros with Linux

U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>

driver/ddr/fsl: Fix DDR4 driver

When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.

Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix tXP and tCKE

The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support of overriding chip select write leveling

JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/freescale: Add support of accumulate ECC

If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Fix DDR register timing_cfg_8

The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr: Fix possible out of bounds error

This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add DDR4 support to Freescale DDR driver

Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Add 256 byte interleaving support

Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Change Freescale ARM DDR driver to support both big and little endian

Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc8xxx: Extend DDR registers' fields

Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx

Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

ddr: Remove <common.h> and add needed includes

Remove <common.h> from this driver directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Finish CONFIG -> CFG migration

At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace

Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Make bank_addr_bits reflect actual bits

In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.

There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.

Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ppc: Remove MPC8555CDS boards

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ppc: Remove MPC8541CDS board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

common: Drop linux/bitops.h from common header

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: Drop log.h from common header

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "drivers/ddr/fsl: Dual-license DDR driver"

Upon further review, not all code authors are in favour of this change.
This reverts commit ee3556bcafbb05e59aabdc31368984e76acaabc4.

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/ddr/fsl: Dual-license DDR driver

To make this driver easier to be reused, dual-license DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/ddr/fsl: Add calculation of register control words

DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Add 3DS RDIMM support

On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Fix DDR4 RDIMM support

For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.

Signed-off-by: York Sun <york.sun@nxp.com>

common: arm: freescale: layerscape: Move header files out of common.h

We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: freescale: Move arch-specific declarations

The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS

These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl/ddr: Add erratum_a009942_check_cpo and clean related erratum

- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>

powerpc: MPC8555: Remove macro CONFIG_MPC8555

Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc8541: Remove macro CONFIG_MPC8541

Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Fix timing_cfg_2

Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>

Various, unrelated tree-wide typo fixes.

Fix a number of typos, including:

* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

drivers/ddr/fsl: Fix timing_cfg_2 register

Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl

The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete

Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Update timing config for heavy load

In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update MR5 RTT park

For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update DDR4 MR6 for Vref range

MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl_ddr: Make SR_IE configurable

SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix driver to support empty first slot

CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl: Update DDR driver for DDR4

Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.

Signed-off-by: York Sun <yorksun@freescale.com>

MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT register

According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.

>From section 9.4.1.8 of that manual:

Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.

0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.

In addition, Freescale application note AN2805 is also very clear that
this bit must be set.

This patch reverts a change introduced by commit
457caecdbca3df21a93abff19eab12dbc61b7897.

Testing Done:

Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:

fff9b774: 65 29 80 00 oris r9,r9,32768

Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.

Booted an image on a MPC8541 based board successfully.

Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix a typo in timing_cfg_8 calculation

wwt_bg should match rrt_bg. It was a typo in driver.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support for multiple DDR clocks

Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust CAS to preamble override for emulator

On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.

These should be set before MEM_EN is set.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix MRC_CYC calculation for DDR3

For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.

DDR4 is not affected by this change.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots

Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>

linux/kernel.h: sync min, max, min3, max3 macros with Linux

U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>

driver/ddr/fsl: Fix DDR4 driver

When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.

Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix tXP and tCKE

The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support of overriding chip select write leveling

JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/freescale: Add support of accumulate ECC

If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Fix DDR register timing_cfg_8

The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr: Fix possible out of bounds error

This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add DDR4 support to Freescale DDR driver

Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Add 256 byte interleaving support

Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Change Freescale ARM DDR driver to support both big and little endian

Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc8xxx: Extend DDR registers' fields

Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx

Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

global: Finish CONFIG -> CFG migration

At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace

Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Make bank_addr_bits reflect actual bits

In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.

There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.

Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ppc: Remove MPC8555CDS boards

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ppc: Remove MPC8541CDS board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

common: Drop linux/bitops.h from common header

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: Drop log.h from common header

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "drivers/ddr/fsl: Dual-license DDR driver"

Upon further review, not all code authors are in favour of this change.
This reverts commit ee3556bcafbb05e59aabdc31368984e76acaabc4.

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/ddr/fsl: Dual-license DDR driver

To make this driver easier to be reused, dual-license DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/ddr/fsl: Add calculation of register control words

DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Add 3DS RDIMM support

On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Fix DDR4 RDIMM support

For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.

Signed-off-by: York Sun <york.sun@nxp.com>

common: arm: freescale: layerscape: Move header files out of common.h

We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: freescale: Move arch-specific declarations

The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS

These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl/ddr: Add erratum_a009942_check_cpo and clean related erratum

- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>

powerpc: MPC8555: Remove macro CONFIG_MPC8555

Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc8541: Remove macro CONFIG_MPC8541

Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Fix timing_cfg_2

Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>

Various, unrelated tree-wide typo fixes.

Fix a number of typos, including:

* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

drivers/ddr/fsl: Fix timing_cfg_2 register

Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl

The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete

Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Update timing config for heavy load

In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update MR5 RTT park

For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update DDR4 MR6 for Vref range

MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl_ddr: Make SR_IE configurable

SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix driver to support empty first slot

CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl: Update DDR driver for DDR4

Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.

Signed-off-by: York Sun <yorksun@freescale.com>

MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT register

According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.

>From section 9.4.1.8 of that manual:

Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.

0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.

In addition, Freescale application note AN2805 is also very clear that
this bit must be set.

This patch reverts a change introduced by commit
457caecdbca3df21a93abff19eab12dbc61b7897.

Testing Done:

Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:

fff9b774: 65 29 80 00 oris r9,r9,32768

Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.

Booted an image on a MPC8541 based board successfully.

Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix a typo in timing_cfg_8 calculation

wwt_bg should match rrt_bg. It was a typo in driver.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support for multiple DDR clocks

Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust CAS to preamble override for emulator

On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.

These should be set before MEM_EN is set.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix MRC_CYC calculation for DDR3

For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.

DDR4 is not affected by this change.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots

Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>

linux/kernel.h: sync min, max, min3, max3 macros with Linux

U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>

driver/ddr/fsl: Fix DDR4 driver

When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.

Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix tXP and tCKE

The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support of overriding chip select write leveling

JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/freescale: Add support of accumulate ECC

If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Fix DDR register timing_cfg_8

The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr: Fix possible out of bounds error

This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add DDR4 support to Freescale DDR driver

Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Add 256 byte interleaving support

Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Change Freescale ARM DDR driver to support both big and little endian

Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc8xxx: Extend DDR registers' fields

Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx

Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace

Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Make bank_addr_bits reflect actual bits

In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.

There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.

Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ppc: Remove MPC8555CDS boards

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ppc: Remove MPC8541CDS board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

common: Drop linux/bitops.h from common header

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: Drop log.h from common header

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "drivers/ddr/fsl: Dual-license DDR driver"

Upon further review, not all code authors are in favour of this change.
This reverts commit ee3556bcafbb05e59aabdc31368984e76acaabc4.

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/ddr/fsl: Dual-license DDR driver

To make this driver easier to be reused, dual-license DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/ddr/fsl: Add calculation of register control words

DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Add 3DS RDIMM support

On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Fix DDR4 RDIMM support

For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.

Signed-off-by: York Sun <york.sun@nxp.com>

common: arm: freescale: layerscape: Move header files out of common.h

We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: freescale: Move arch-specific declarations

The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS

These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl/ddr: Add erratum_a009942_check_cpo and clean related erratum

- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>

powerpc: MPC8555: Remove macro CONFIG_MPC8555

Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc8541: Remove macro CONFIG_MPC8541

Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Fix timing_cfg_2

Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>

Various, unrelated tree-wide typo fixes.

Fix a number of typos, including:

* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

drivers/ddr/fsl: Fix timing_cfg_2 register

Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl

The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete

Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Update timing config for heavy load

In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update MR5 RTT park

For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update DDR4 MR6 for Vref range

MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl_ddr: Make SR_IE configurable

SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix driver to support empty first slot

CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl: Update DDR driver for DDR4

Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.

Signed-off-by: York Sun <yorksun@freescale.com>

MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT register

According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.

>From section 9.4.1.8 of that manual:

Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.

0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.

In addition, Freescale application note AN2805 is also very clear that
this bit must be set.

This patch reverts a change introduced by commit
457caecdbca3df21a93abff19eab12dbc61b7897.

Testing Done:

Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:

fff9b774: 65 29 80 00 oris r9,r9,32768

Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.

Booted an image on a MPC8541 based board successfully.

Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix a typo in timing_cfg_8 calculation

wwt_bg should match rrt_bg. It was a typo in driver.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support for multiple DDR clocks

Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust CAS to preamble override for emulator

On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.

These should be set before MEM_EN is set.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix MRC_CYC calculation for DDR3

For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.

DDR4 is not affected by this change.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots

Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>

linux/kernel.h: sync min, max, min3, max3 macros with Linux

U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>

driver/ddr/fsl: Fix DDR4 driver

When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.

Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix tXP and tCKE

The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support of overriding chip select write leveling

JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/freescale: Add support of accumulate ECC

If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Fix DDR register timing_cfg_8

The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr: Fix possible out of bounds error

This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add DDR4 support to Freescale DDR driver

Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Add 256 byte interleaving support

Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Change Freescale ARM DDR driver to support both big and little endian

Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc8xxx: Extend DDR registers' fields

Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx

Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace

Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ddr: fsl: Make bank_addr_bits reflect actual bits

In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.

There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.

Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ppc: Remove MPC8555CDS boards

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ppc: Remove MPC8541CDS board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

common: Drop linux/bitops.h from common header

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: Drop log.h from common header

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "drivers/ddr/fsl: Dual-license DDR driver"

Upon further review, not all code authors are in favour of this change.
This reverts commit ee3556bcafbb05e59aabdc31368984e76acaabc4.

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/ddr/fsl: Dual-license DDR driver

To make this driver easier to be reused, dual-license DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/ddr/fsl: Add calculation of register control words

DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Add 3DS RDIMM support

On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Fix DDR4 RDIMM support

For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.

Signed-off-by: York Sun <york.sun@nxp.com>

common: arm: freescale: layerscape: Move header files out of common.h

We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: freescale: Move arch-specific declarations

The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS

These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl/ddr: Add erratum_a009942_check_cpo and clean related erratum

- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>

powerpc: MPC8555: Remove macro CONFIG_MPC8555

Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc8541: Remove macro CONFIG_MPC8541

Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Fix timing_cfg_2

Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>

Various, unrelated tree-wide typo fixes.

Fix a number of typos, including:

* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

drivers/ddr/fsl: Fix timing_cfg_2 register

Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl

The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete

Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Update timing config for heavy load

In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update MR5 RTT park

For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update DDR4 MR6 for Vref range

MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl_ddr: Make SR_IE configurable

SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix driver to support empty first slot

CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl: Update DDR driver for DDR4

Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.

Signed-off-by: York Sun <yorksun@freescale.com>

MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT register

According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.

>From section 9.4.1.8 of that manual:

Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.

0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.

In addition, Freescale application note AN2805 is also very clear that
this bit must be set.

This patch reverts a change introduced by commit
457caecdbca3df21a93abff19eab12dbc61b7897.

Testing Done:

Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:

fff9b774: 65 29 80 00 oris r9,r9,32768

Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.

Booted an image on a MPC8541 based board successfully.

Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix a typo in timing_cfg_8 calculation

wwt_bg should match rrt_bg. It was a typo in driver.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support for multiple DDR clocks

Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust CAS to preamble override for emulator

On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.

These should be set before MEM_EN is set.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix MRC_CYC calculation for DDR3

For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.

DDR4 is not affected by this change.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots

Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>

linux/kernel.h: sync min, max, min3, max3 macros with Linux

U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>

driver/ddr/fsl: Fix DDR4 driver

When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.

Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix tXP and tCKE

The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support of overriding chip select write leveling

JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/freescale: Add support of accumulate ECC

If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Fix DDR register timing_cfg_8

The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr: Fix possible out of bounds error

This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add DDR4 support to Freescale DDR driver

Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Add 256 byte interleaving support

Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Change Freescale ARM DDR driver to support both big and little endian

Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc8xxx: Extend DDR registers' fields

Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx

Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

ddr: fsl: Make bank_addr_bits reflect actual bits

In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.

There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.

Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ppc: Remove MPC8555CDS boards

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ppc: Remove MPC8541CDS board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

common: Drop linux/bitops.h from common header

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: Drop log.h from common header

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "drivers/ddr/fsl: Dual-license DDR driver"

Upon further review, not all code authors are in favour of this change.
This reverts commit ee3556bcafbb05e59aabdc31368984e76acaabc4.

Signed-off-by: Tom Rini <trini@konsulko.com>

drivers/ddr/fsl: Dual-license DDR driver

To make this driver easier to be reused, dual-license DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/ddr/fsl: Add calculation of register control words

DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Add 3DS RDIMM support

On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Fix DDR4 RDIMM support

For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.

Signed-off-by: York Sun <york.sun@nxp.com>

common: arm: freescale: layerscape: Move header files out of common.h

We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

common: freescale: Move arch-specific declarations

The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>

ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS

These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

fsl/ddr: Add erratum_a009942_check_cpo and clean related erratum

- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>

powerpc: MPC8555: Remove macro CONFIG_MPC8555

Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

powerpc: mpc8541: Remove macro CONFIG_MPC8541

Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Fix timing_cfg_2

Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>

Various, unrelated tree-wide typo fixes.

Fix a number of typos, including:

* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

drivers/ddr/fsl: Fix timing_cfg_2 register

Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>

drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl

The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete

Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver/ddr/fsl: Update timing config for heavy load

In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update MR5 RTT park

For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Update DDR4 MR6 for Vref range

MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl_ddr: Make SR_IE configurable

SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix driver to support empty first slot

CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr/fsl: Update DDR driver for DDR4

Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.

Signed-off-by: York Sun <yorksun@freescale.com>

MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT register

According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.

>From section 9.4.1.8 of that manual:

Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.

0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.

In addition, Freescale application note AN2805 is also very clear that
this bit must be set.

This patch reverts a change introduced by commit
457caecdbca3df21a93abff19eab12dbc61b7897.

Testing Done:

Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:

fff9b774: 65 29 80 00 oris r9,r9,32768

Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.

Booted an image on a MPC8541 based board successfully.

Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix a typo in timing_cfg_8 calculation

wwt_bg should match rrt_bg. It was a typo in driver.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support for multiple DDR clocks

Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust CAS to preamble override for emulator

On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.

These should be set before MEM_EN is set.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix MRC_CYC calculation for DDR3

For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.

DDR4 is not affected by this change.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots

Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>

linux/kernel.h: sync min, max, min3, max3 macros with Linux

U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>

driver/ddr/fsl: Fix DDR4 driver

When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.

Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Fix tXP and tCKE

The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add support of overriding chip select write leveling

JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr/freescale: Add support of accumulate ECC

If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Fix DDR register timing_cfg_8

The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

drivers/ddr: Fix possible out of bounds error

This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

driver/ddr/fsl: Add DDR4 support to Freescale DDR driver

Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Add 256 byte interleaving support

Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.

Signed-off-by: York Sun <yorksun@freescale.com>

driver/ddr: Change Freescale ARM DDR driver to support both big and little endian

Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/mpc8xxx: Extend DDR registers' fields

Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx

Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>