sunxi: remove CONFIG_MMC?_CD_PIN

For legacy reasons we were defining the card detect GPIO for all sunxi
boards in each board's defconfig.
There is actually no need for a card-detect check in the SPL code (which
consequently has been removed already), and also in U-Boot proper we
have DM code to query the CD GPIO name from the device tree.

That means we don't have any user of that information left, so can
remove the definitions from the defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>

sunxi: define SYS_MONITOR_LEN in Kconfig, not _defconfig

Commit 08574ed339fb ("Convert CONFIG_SYS_MONITOR_LEN to Kconfig") moved
the definition of said config variable from the common sunxi header to
*every board's* defconfig.
This is a platform choice, not board specific, so remove the variable
from there, instead set the one value for all Allwinner boards in
Kconfig.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: defconfig: drop redundant definitions

When some configuration symbols were converted from header files to
Kconfig, their values were placed into *every* defconfig file.
Since we now have sensible per-SoC defaults defined in Kconfig, those
values are now redundant, and can just be removed.
This affects CONFIG_SPL_STACK, CONFIG_SYS_PBSIZE, CONFIG_SPL_MAX_SIZE,
and CONFIG_SYS_BOOTM_LEN.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_SPEED
CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_MVTWSI to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER

Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.

Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig

We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.

Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: define SYS_MONITOR_LEN in Kconfig, not _defconfig

Commit 08574ed339fb ("Convert CONFIG_SYS_MONITOR_LEN to Kconfig") moved
the definition of said config variable from the common sunxi header to
*every board's* defconfig.
This is a platform choice, not board specific, so remove the variable
from there, instead set the one value for all Allwinner boards in
Kconfig.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: defconfig: drop redundant definitions

When some configuration symbols were converted from header files to
Kconfig, their values were placed into *every* defconfig file.
Since we now have sensible per-SoC defaults defined in Kconfig, those
values are now redundant, and can just be removed.
This affects CONFIG_SPL_STACK, CONFIG_SYS_PBSIZE, CONFIG_SPL_MAX_SIZE,
and CONFIG_SYS_BOOTM_LEN.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_SPEED
CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_MVTWSI to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER

Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.

Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig

We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.

Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: defconfig: drop redundant definitions

When some configuration symbols were converted from header files to
Kconfig, their values were placed into *every* defconfig file.
Since we now have sensible per-SoC defaults defined in Kconfig, those
values are now redundant, and can just be removed.
This affects CONFIG_SPL_STACK, CONFIG_SYS_PBSIZE, CONFIG_SPL_MAX_SIZE,
and CONFIG_SYS_BOOTM_LEN.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_SPEED
CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_MVTWSI to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER

Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.

Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig

We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.

Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: defconfig: drop redundant definitions

When some configuration symbols were converted from header files to
Kconfig, their values were placed into *every* defconfig file.
Since we now have sensible per-SoC defaults defined in Kconfig, those
values are now redundant, and can just be removed.
This affects CONFIG_SPL_STACK, CONFIG_SYS_PBSIZE, CONFIG_SPL_MAX_SIZE,
and CONFIG_SYS_BOOTM_LEN.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_SPEED
CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_MVTWSI to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER

Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.

Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig

We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.

Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Convert CONFIG_SPL_STACK to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_SPEED
CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_MVTWSI to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER

Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.

Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig

We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.

Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_SPEED
CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_MVTWSI to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>

sunxi: Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER

Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.

Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig

We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.

Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

i2c: Rename SPL/TPL_I2C_SUPPORT to I2C

Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Remove no longer needed default options from defconfigs

Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: usb: Switch to Generic host controllers

Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

part: Disable CONFIG_SPL_ISO_PARTITION by default

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

# CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

configs: Migrate all of the existing USB symbols, except fastboot

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_ISO_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_SPL_I2C_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync with savedefconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable a bunch of commands by default on sunxi

Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync HUSH options

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: Enable CMD_GPIO on all sunxi boards

We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.

Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Kconfig: Move CONFIG_FIT and related options to Kconfig

There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>

sunxi: select SYS_NS16550 from Kconfig

Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

common: add CMD_GPIO to Kconfig

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>