#
636da203 |
|
05-Feb-2023 |
Safae Ouajih <souajih@baylibre.com> |
android: boot: support boot image header version 3 and 4 Enable the support for boot image header version 3 and 4 using abootimg command. In order to use version 3 or 4: 1- Vendor boot image address should be given to abootimg cmd. abootimg addr $1 $vendor_boot_load_addr 2- "ramdisk_addr_r" env variable (ramdisk address) should be set to host the ramdisk : generic ramdisk + vendor ramdisk Replace "struct andr_boot_img_hdr_v0*" by "void *" in some functions since v3 and v4 are now supported as well. Signed-off-by: Safae Ouajih <souajih@baylibre.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> |
#
e058176b |
|
05-Feb-2023 |
Safae Ouajih <souajih@baylibre.com> |
android: boot: add vendor boot image to prepare for v3, v4 support Introduce vendor boot image for version 3 and 4 of boot image header. The vendor boot image will hold extra information about kernel, dtb and ramdisk. This is done to prepare for boot image version 3 and 4 support. Signed-off-by: Safae Ouajih <souajih@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> |
#
607b0755 |
|
05-Feb-2023 |
Safae Ouajih <souajih@baylibre.com> |
android: boot: move to andr_image_data structure Move from andr_boot_img_hdr_v0 to andr_image_data structure to prepare for boot image header version 3 and 4. Signed-off-by: Safae Ouajih <souajih@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> |
#
734cb47d |
|
05-Feb-2023 |
Safae Ouajih <souajih@baylibre.com> |
android: boot: replace android_image_check_header With the new vendor boot image introduced in versions 3 and 4 of boot image header, the header check must be done for both boot image and vendor boot image. Thus, replace android_image_check_header() by is_android_boot_image_header() to only refer to boot image header check. Signed-off-by: Safae Ouajih <souajih@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> |
#
86b62947 |
|
05-Feb-2023 |
Safae Ouajih <souajih@baylibre.com> |
android: boot: support vendor boot image in abootimg Vendor boot image is introduced in boot image header version 3 and 4. Please check [1] for more details. To prepare for boot image v3/v4 support, allow the abootimg command to store the vendor_boot image address. Full support for this new format will be done in a future patch. Link:[1] https://source.android.com/docs/core/architecture/bootloader/partitions/vendor-boot-partitions Signed-off-by: Safae Ouajih <souajih@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> |
#
d71a732a |
|
05-Feb-2023 |
Safae Ouajih <souajih@baylibre.com> |
android: boot: rename andr_img_hdr -> andr_boot_img_hdr_v0 Android introduced boot header version 3 or 4. The header structure change with version 3 and 4 to support the new updates such as: - Introducing Vendor boot image: with a vendor ramdisk - Bootconfig feature (v4) Change andr_img_hdr struct name to maintain support for version v0, v1 and v2 while introducing version 3 and 4. Signed-off-by: Safae Ouajih <souajih@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> |
#
7e5f460e |
|
24-Jul-2021 |
Simon Glass <sjg@chromium.org> |
global: Convert simple_strtoul() with hex to hextoul() It is a pain to have to specify the value 16 in each call. Add a new hextoul() function and update the code to use it. Add a proper comment to simple_strtoul() while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> |
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org> |
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org> |
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> |
#
7e5f460e |
|
24-Jul-2021 |
Simon Glass <sjg@chromium.org> |
global: Convert simple_strtoul() with hex to hextoul() It is a pain to have to specify the value 16 in each call. Add a new hextoul() function and update the code to use it. Add a proper comment to simple_strtoul() while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> |
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org> |
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org> |
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> |
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
09140113 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
command: Remove the cmd_tbl_t typedef We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
4d72caa5 |
|
10-May-2020 |
Simon Glass <sjg@chromium.org> |
common: Drop image.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
#
94f6d0d1 |
|
24-Jan-2020 |
Sam Protsenko <joe.skb7@gmail.com> |
cmd: abootimg: Add abootimg command This command can be used to extract fields and image payloads from Android Boot Image. It can be used for example to implement boot flow where dtb is taken from boot.img (as v2 incorporated dtb inside of boot.img). Using this command, one can obtain needed dtb blob from boot.img in scripting manner, and then apply needed dtbo's (from "dtbo" partition) on top of that, providing then the resulting image to bootm command in order to boot the Android. Also right now this command has the sub-command to get an address and size of recovery dtbo from recovery image (for non-A/B devices only, see [1,2] for details). It can be tested like this: => mmc dev 1 => part start mmc 1 boot_a boot_start => part size mmc 1 boot_a boot_size => mmc read $loadaddr $boot_start $boot_size => abootimg get ver => abootimg dump dtb [1] https://source.android.com/devices/bootloader/boot-image-header [2] https://source.android.com/devices/architecture/dto/partitions Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|