Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

board: synquacer: Add DeveloperBox 96boards EE support

Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: socionext: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

board: developerbox: fix mem_map setup timing

The setup of global variable mem_map was moved into enable_caches()
by commit a70c75cabae1 ("board: developerbox: move mem_map setup later")
since U-Boot was directly booted from NOR flash in XIP
and bss is not yet available in dram_init() at that time.
This has a problem, mem_map variable is used by
the get_page_table_size() to calculate the page table size,
but get_page_table_size() is called earlier than enable_caches()
which fills mem_map variable. With that, U-Boot fails to boot when
64GB DIMM is installed.

Currently U-Boot on the Developerbox board is not booted in XIP
and bss is available in dram_init(), let's move mem_map setup
in dram_init().

Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>

board: synquacer: Update the flash image layout

The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>

board: synquacer: set actual gd->ram_top and gd->ram_size

Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c37 ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.

Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>

fwu: DeveloperBox: add support for FWU

Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

efi_loader: add the number of image entries in efi_capsule_update_info

The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.

This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Correct SPL uses of EFI_HAVE_CAPSULE_SUPPORT

This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>

board: developerbox: move mem_map setup later

dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

board: developerbox: use identity mapping for >4GB

Identity-map the second and later memory banks which are located >4GB.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

capsule: board: Add information needed for capsule updates

Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>

Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"

Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.

This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

board: synquacer: developerbox: Don't set gd->env_addr to default_environment

This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: synquacer: Initialize SCBM SMMU at board_init()

Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.

Move the SMMU initialization code into board support
and call it from board_init().

Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>