Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Acked-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phycore_imx8mp: Use 2GHz RAM timings for PCL-070 from pcb_rev 1

We need to differ between PCL-070 and PCM-070. PCL-070 supports 2GHz RAM
timings from pcb rev 1 or newer. PCM-070 supports 2GHz RAM timings from
pcb rev 3 or newer.

Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>

board: phytec: phycore_imx8mp: Add 4000MTS RAM timings based on PCB rev

Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

board: phytec: phycore-imx8mp: Add EEPROM detection initialisation

Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

imx: phycore_imx8mm/p: clean up board watchdog code

pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>

imx: imx8m[m/p]_phycore: Enable DM_SERIAL

Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>

board: phytec: phycore-imx8mp: Enable DVS1 control

Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V

Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Change debug UART

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: Remove <common.h> and add needed includes

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Acked-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phycore_imx8mp: Use 2GHz RAM timings for PCL-070 from pcb_rev 1

We need to differ between PCL-070 and PCM-070. PCL-070 supports 2GHz RAM
timings from pcb rev 1 or newer. PCM-070 supports 2GHz RAM timings from
pcb rev 3 or newer.

Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>

board: phytec: phycore_imx8mp: Add 4000MTS RAM timings based on PCB rev

Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

board: phytec: phycore-imx8mp: Add EEPROM detection initialisation

Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

imx: phycore_imx8mm/p: clean up board watchdog code

pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>

imx: imx8m[m/p]_phycore: Enable DM_SERIAL

Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>

board: phytec: phycore-imx8mp: Enable DVS1 control

Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V

Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Change debug UART

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phycore_imx8mp: Use 2GHz RAM timings for PCL-070 from pcb_rev 1

We need to differ between PCL-070 and PCM-070. PCL-070 supports 2GHz RAM
timings from pcb rev 1 or newer. PCM-070 supports 2GHz RAM timings from
pcb rev 3 or newer.

Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>

board: phytec: phycore_imx8mp: Add 4000MTS RAM timings based on PCB rev

Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

board: phytec: phycore-imx8mp: Add EEPROM detection initialisation

Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

imx: phycore_imx8mm/p: clean up board watchdog code

pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>

imx: imx8m[m/p]_phycore: Enable DM_SERIAL

Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>

board: phytec: phycore-imx8mp: Enable DVS1 control

Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V

Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Change debug UART

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: phycore_imx8mp: Add 4000MTS RAM timings based on PCB rev

Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

board: phytec: phycore-imx8mp: Add EEPROM detection initialisation

Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>

imx: phycore_imx8mm/p: clean up board watchdog code

pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>

imx: imx8m[m/p]_phycore: Enable DM_SERIAL

Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>

board: phytec: phycore-imx8mp: Enable DVS1 control

Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V

Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Change debug UART

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

imx: phycore_imx8mm/p: clean up board watchdog code

pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>

imx: imx8m[m/p]_phycore: Enable DM_SERIAL

Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>

board: phytec: phycore-imx8mp: Enable DVS1 control

Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V

Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Change debug UART

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: phycore-imx8mp: Enable DVS1 control

Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V

Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

board: phytec: phycore_imx8mp: Change debug UART

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

power: pca9450: add a new parameter for power_pca9450_init

Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

common: Drop asm/global_data.h from common header

Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>