arm: Drop <common.h> from remaining header files

None of these header files need to include <common.h> so we can just
drop that entirely.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm64: zynqmp: Fix debug uart initialization

The commit 0dba45864b2a ("arm: Init the debug UART") calls
debug_uart_init() from crt0.S but it won't work because SOC is not
configured yet. That's why create board_debug_uart_init() which calls
psu_init() via new psu_uboot_init() earlier before the first access to UART
in SPL. In full U-Boot call psu_uboot_init() only when
CONFIG_ZYNQMP_PSU_INIT_ENABLED is enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/878dc2daaa8685346f889989fbfb98b2e44da7fb.1645104518.git.michal.simek@xilinx.com

arm64: zynqmp: Do not assing MIO34 that early on zcu100

MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Move SoC sources to mach-zynqmp

Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.

Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.

Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Fix debug uart initialization

The commit 0dba45864b2a ("arm: Init the debug UART") calls
debug_uart_init() from crt0.S but it won't work because SOC is not
configured yet. That's why create board_debug_uart_init() which calls
psu_init() via new psu_uboot_init() earlier before the first access to UART
in SPL. In full U-Boot call psu_uboot_init() only when
CONFIG_ZYNQMP_PSU_INIT_ENABLED is enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/878dc2daaa8685346f889989fbfb98b2e44da7fb.1645104518.git.michal.simek@xilinx.com

arm64: zynqmp: Do not assing MIO34 that early on zcu100

MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Move SoC sources to mach-zynqmp

Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.

Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.

Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Do not assing MIO34 that early on zcu100

MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Move SoC sources to mach-zynqmp

Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.

Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.

Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Move SoC sources to mach-zynqmp

Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.

Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.

Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>