PR/57889: Ricardo Branco: ext2fs does not have user immutable and append
file flags, only system ones. Restrict those to the superuser. Before
the behavior was controlled by EXT2FS_SYSTEM_FLAGS. Make that behavior the
default.

UFS/LFS dirhash:
- Enable UFS_DIRHASH if the architecture or kernel model specific config
file can use 128MB of RAM or more.
- Remove experimental tag from UFS_DIRHASH; it's been with RUMP kernel
and by a number of NetBSD developers for years.
- Add LFS_DIRHASH if LFS was enabled.
- Be somewhat consistent with FS options order.

Comment out HZ=512. This was only intended to be enabled for profiling.

Correct the comment at the top of these config files identifying what
they run on.

branches: 1.30.2;
Fix outdated or misleading comments for MEMORY_DISK_ROOT_SIZE.
No functional changes.

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

branches: 1.28.4;
Enable BUFQ_PRIOCSCAN, CARP, Veriexec by default in GENERIC kernel configs.
On ports without a GENERIC kernel config enable in individul files, e.g evbmips.
Omit on:
atari, dreamcast, emips, epoc32, evbppc/VIRTEX*, ia64, luna68x, mvme68k,
mvmeppc, playstation2, riscv, sun2, sun3, x68k, zaurus due to resource
constraints or port infancy.

Enable the per-priority cyclical scan buffer queue strategy on evbmips kernels.

time results of a Lemote Fuloong 2F extracting the pkgsrc tree
brick$ time tar -jxf pkgsrc.tar.bz2
priocscan + log
612.90 real 103.45 user 194.98 sys
priocscan nolog
1345.48 real 103.57 user 274.32 sys
fcfs + log
736.02 real 101.71 user 192.95 sys
fcfs nolog
1475.16 real 103.06 user 271.14 sys

remove the 'wd* at umass?' for the non-standardized and rare (extinct?)
In-System Design ATA protocol over Bulk-Only devices from most kernels,
leave only in i386/amd64 ALL; it's unmaintained and likely currently broken,
lack of test hardware makes it impossible to support

Unreference IPF/PF from all the config files, and enable NPF instead when
wanted. This also fixes some inconsistencies I saw in several files (eg
IPF options while IPF was not compiled, IPF+PF enabled by default, etc).

Remove comment mentioning an i386 problem from non-x86 kernel configs.
(they all say BROKEN in the next comment too)

branches: 1.23.2; 1.23.4;
clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

branches: 1.21.6;
PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

UFS/LFS dirhash:
- Enable UFS_DIRHASH if the architecture or kernel model specific config
file can use 128MB of RAM or more.
- Remove experimental tag from UFS_DIRHASH; it's been with RUMP kernel
and by a number of NetBSD developers for years.
- Add LFS_DIRHASH if LFS was enabled.
- Be somewhat consistent with FS options order.

Comment out HZ=512. This was only intended to be enabled for profiling.

Correct the comment at the top of these config files identifying what
they run on.

branches: 1.30.2;
Fix outdated or misleading comments for MEMORY_DISK_ROOT_SIZE.
No functional changes.

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

branches: 1.28.4;
Enable BUFQ_PRIOCSCAN, CARP, Veriexec by default in GENERIC kernel configs.
On ports without a GENERIC kernel config enable in individul files, e.g evbmips.
Omit on:
atari, dreamcast, emips, epoc32, evbppc/VIRTEX*, ia64, luna68x, mvme68k,
mvmeppc, playstation2, riscv, sun2, sun3, x68k, zaurus due to resource
constraints or port infancy.

Enable the per-priority cyclical scan buffer queue strategy on evbmips kernels.

time results of a Lemote Fuloong 2F extracting the pkgsrc tree
brick$ time tar -jxf pkgsrc.tar.bz2
priocscan + log
612.90 real 103.45 user 194.98 sys
priocscan nolog
1345.48 real 103.57 user 274.32 sys
fcfs + log
736.02 real 101.71 user 192.95 sys
fcfs nolog
1475.16 real 103.06 user 271.14 sys

remove the 'wd* at umass?' for the non-standardized and rare (extinct?)
In-System Design ATA protocol over Bulk-Only devices from most kernels,
leave only in i386/amd64 ALL; it's unmaintained and likely currently broken,
lack of test hardware makes it impossible to support

Unreference IPF/PF from all the config files, and enable NPF instead when
wanted. This also fixes some inconsistencies I saw in several files (eg
IPF options while IPF was not compiled, IPF+PF enabled by default, etc).

Remove comment mentioning an i386 problem from non-x86 kernel configs.
(they all say BROKEN in the next comment too)

branches: 1.23.2; 1.23.4;
clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

branches: 1.21.6;
PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

Comment out HZ=512. This was only intended to be enabled for profiling.

Correct the comment at the top of these config files identifying what
they run on.

Fix outdated or misleading comments for MEMORY_DISK_ROOT_SIZE.
No functional changes.

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

branches: 1.28.4;
Enable BUFQ_PRIOCSCAN, CARP, Veriexec by default in GENERIC kernel configs.
On ports without a GENERIC kernel config enable in individul files, e.g evbmips.
Omit on:
atari, dreamcast, emips, epoc32, evbppc/VIRTEX*, ia64, luna68x, mvme68k,
mvmeppc, playstation2, riscv, sun2, sun3, x68k, zaurus due to resource
constraints or port infancy.

Enable the per-priority cyclical scan buffer queue strategy on evbmips kernels.

time results of a Lemote Fuloong 2F extracting the pkgsrc tree
brick$ time tar -jxf pkgsrc.tar.bz2
priocscan + log
612.90 real 103.45 user 194.98 sys
priocscan nolog
1345.48 real 103.57 user 274.32 sys
fcfs + log
736.02 real 101.71 user 192.95 sys
fcfs nolog
1475.16 real 103.06 user 271.14 sys

remove the 'wd* at umass?' for the non-standardized and rare (extinct?)
In-System Design ATA protocol over Bulk-Only devices from most kernels,
leave only in i386/amd64 ALL; it's unmaintained and likely currently broken,
lack of test hardware makes it impossible to support

Unreference IPF/PF from all the config files, and enable NPF instead when
wanted. This also fixes some inconsistencies I saw in several files (eg
IPF options while IPF was not compiled, IPF+PF enabled by default, etc).

Remove comment mentioning an i386 problem from non-x86 kernel configs.
(they all say BROKEN in the next comment too)

branches: 1.23.2; 1.23.4;
clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

branches: 1.21.6;
PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

Fix outdated or misleading comments for MEMORY_DISK_ROOT_SIZE.
No functional changes.

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

branches: 1.28.4;
Enable BUFQ_PRIOCSCAN, CARP, Veriexec by default in GENERIC kernel configs.
On ports without a GENERIC kernel config enable in individul files, e.g evbmips.
Omit on:
atari, dreamcast, emips, epoc32, evbppc/VIRTEX*, ia64, luna68x, mvme68k,
mvmeppc, playstation2, riscv, sun2, sun3, x68k, zaurus due to resource
constraints or port infancy.

Enable the per-priority cyclical scan buffer queue strategy on evbmips kernels.

time results of a Lemote Fuloong 2F extracting the pkgsrc tree
brick$ time tar -jxf pkgsrc.tar.bz2
priocscan + log
612.90 real 103.45 user 194.98 sys
priocscan nolog
1345.48 real 103.57 user 274.32 sys
fcfs + log
736.02 real 101.71 user 192.95 sys
fcfs nolog
1475.16 real 103.06 user 271.14 sys

remove the 'wd* at umass?' for the non-standardized and rare (extinct?)
In-System Design ATA protocol over Bulk-Only devices from most kernels,
leave only in i386/amd64 ALL; it's unmaintained and likely currently broken,
lack of test hardware makes it impossible to support

Unreference IPF/PF from all the config files, and enable NPF instead when
wanted. This also fixes some inconsistencies I saw in several files (eg
IPF options while IPF was not compiled, IPF+PF enabled by default, etc).

Remove comment mentioning an i386 problem from non-x86 kernel configs.
(they all say BROKEN in the next comment too)

branches: 1.23.2; 1.23.4;
clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

branches: 1.21.6;
PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

Enable BUFQ_PRIOCSCAN, CARP, Veriexec by default in GENERIC kernel configs.
On ports without a GENERIC kernel config enable in individul files, e.g evbmips.
Omit on:
atari, dreamcast, emips, epoc32, evbppc/VIRTEX*, ia64, luna68x, mvme68k,
mvmeppc, playstation2, riscv, sun2, sun3, x68k, zaurus due to resource
constraints or port infancy.

Enable the per-priority cyclical scan buffer queue strategy on evbmips kernels.

time results of a Lemote Fuloong 2F extracting the pkgsrc tree
brick$ time tar -jxf pkgsrc.tar.bz2
priocscan + log
612.90 real 103.45 user 194.98 sys
priocscan nolog
1345.48 real 103.57 user 274.32 sys
fcfs + log
736.02 real 101.71 user 192.95 sys
fcfs nolog
1475.16 real 103.06 user 271.14 sys

remove the 'wd* at umass?' for the non-standardized and rare (extinct?)
In-System Design ATA protocol over Bulk-Only devices from most kernels,
leave only in i386/amd64 ALL; it's unmaintained and likely currently broken,
lack of test hardware makes it impossible to support

Unreference IPF/PF from all the config files, and enable NPF instead when
wanted. This also fixes some inconsistencies I saw in several files (eg
IPF options while IPF was not compiled, IPF+PF enabled by default, etc).

Remove comment mentioning an i386 problem from non-x86 kernel configs.
(they all say BROKEN in the next comment too)

branches: 1.23.2; 1.23.4;
clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

branches: 1.21.6;
PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

Enable BUFQ_PRIOCSCAN, CARP, Veriexec by default in GENERIC kernel configs.
On ports without a GENERIC kernel config enable in individul files, e.g evbmips.
Omit on:
atari, dreamcast, emips, epoc32, evbppc/VIRTEX*, ia64, luna68x, mvme68k,
mvmeppc, playstation2, riscv, sun2, sun3, x68k, zaurus due to resource
constraints or port infancy.

Enable the per-priority cyclical scan buffer queue strategy on evbmips kernels.

time results of a Lemote Fuloong 2F extracting the pkgsrc tree
brick$ time tar -jxf pkgsrc.tar.bz2
priocscan + log
612.90 real 103.45 user 194.98 sys
priocscan nolog
1345.48 real 103.57 user 274.32 sys
fcfs + log
736.02 real 101.71 user 192.95 sys
fcfs nolog
1475.16 real 103.06 user 271.14 sys

remove the 'wd* at umass?' for the non-standardized and rare (extinct?)
In-System Design ATA protocol over Bulk-Only devices from most kernels,
leave only in i386/amd64 ALL; it's unmaintained and likely currently broken,
lack of test hardware makes it impossible to support

Unreference IPF/PF from all the config files, and enable NPF instead when
wanted. This also fixes some inconsistencies I saw in several files (eg
IPF options while IPF was not compiled, IPF+PF enabled by default, etc).

Remove comment mentioning an i386 problem from non-x86 kernel configs.
(they all say BROKEN in the next comment too)

branches: 1.23.2;
clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

branches: 1.21.6;
PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

clean up COMPAT_* options for native netbsd code:
- new series of files that are useful for saying "i want everything
since netbsd 1.4", etc.
- use the fact COMPAT_* options have future dependancies to remove
many redundant options.

removes about 3000 lines total across kernel configuration files.
tested about 30 random kernels in the changed list.

Remove TCP_COMPAT_42 from the config files. Pass 2.

PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

Remove TCP_COMPAT_42 from the config files. Pass 2.

PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

branches: 1.20.2; 1.20.4;
Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.

PR kern/51208
Add DISKLABEL_EI option (and also FFS_EI if missing), commented out except for
ALL on amd64 and i386.

Remove the KMEMSTATS option. It no longer exists.

branches: 1.19.2;
Systematize (and in many cases, fix) the comments on options COMPAT_NN.

There are quite a few configs that are missing some COMPAT_NN options
in ways that don't make sense; this should probably get cleaned up
too, but for the time being I've not added or removed anything.

Reorganize symbol table embedding. The existing option SYMTAB_SPACE is
replaced by the make option COPY_SYMTAB set to any value. The copy of
the symbol table is no longer put into a buffer in kern_ksyms.o, but a
small helper object. This object is build first with a dummy size, then
the kernel is linked to compute the real dimension of the symbol table
buffer. After that, the helper object is rebuild and the kernel linked
again.

Add commented out bpfjit options to mips kernels.
While here, add 2 missing RCS ids.

branches: 1.16.4;
G/C PFIL_HOOKS from the kernel configs.

branches: 1.15.2;
remove obsolete networking options

more bogus number removal

the bogus number police

Under FAST_IPSEC, IPSEC_ESP is mandatory; GC it.

Retire OSI network stack. OK core@

branches: 1.10.8;

The rnd pseudo-device is not really optional, because it is in the same
source file as the entropy-pool code itself. Move it to std. This
will be cleaned up more when I split the sources up as they should be.

This fixes build breaks on several ports. Thanks to Havard Eidnes for
pointing them out.

branches: 1.9.2;
dependant -> dependent

eliminate obsolete option SOSEND_LOAN

merge the bouyer-quota2 branch. This adds a new on-disk format
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.

See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.

Merge forward from matt-nb5-mips64.

branches: 1.5.2; 1.5.4;
Remove unused count from pseudo-device md.

branches: 1.4.4;
Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Remove softdep, pass 1. We are focused on improving journalling.

Proposed on tech-kern@.

branches: 1.2.2; 1.2.8; 1.2.20; 1.2.40; 1.2.44; 1.2.50; 1.2.52; 1.2.58;
Add extio and gpio so that this compiles again.

branches: 1.1.2;
Add a port to the Infineon ADM5120.

Basics: the ADM5120 is a 175 MHz MIPS32 4Kc processor featuring a
6-port ethernet 10/100 switch with Auto MDI/X, a PCI controller,
USB 1.1 controller, UART, watchdog timer, eight GPIO pins, and a
multiport memory controller with both NOR and NAND flash support.
This code supports most of the devices on the ADM5120, including
the 6-port switch (each port attaches as an ethernet, admsw0 through
admsw5), the PCI controller, USB controller, GPIO, watchdog, and
UART.

Remaining work: the port includes no NOR/NAND flash drivers. No
bootloader is included. I have only tested the PCI bus driver with
the use of one PCI slot on the RouterBOARD 153. It is not possible
to exploit the capabilities of the ethernet switch using bridge(4).
I have only netbooted the ADM5120 on the RB153. Booting other
boards, and booting from flash memory, remains to be done.

Hardware availability: many low-cost routers, including the
RouterBOARD 100 series at RouterBOARD.com, use the Infineon ADM5120
processor.

Credits: Ruslan Ermilov and Vsevolod Lobko ported to the ADM5120,
and they wrote device drivers for the UART, USB controller, and
10/100 switch. Matt Isaacs brought the port up-to-date with
NetBSD-current, made it compile, and ran it first on the RB153.
I added drivers for the PCI controller, GPIO, and watchdog timer.
I produced the bus attachment for the CompactFlash slot with advice
from Mikrotik technical support and from Matt Thomas.