modules: Build `ipl` module only if MKIPFILTER is enabled

make owtemp a module

add compat_100 module setlist entries

Split the BMP280 / BME280 driver into common code and create I2C and
SPI attachments.

A driver for the Bosch BMP280 / BME280 temperature, humidity and
atmospheric pressure sensor. This is an inexpensive to moderately
expensive chip available from a large number of places. The driver
supports all aspects of the two chips, except for the repeating read
mode which would allow for sub-second queries, such as fall detection
or perhaps even as an altimeter. This driver also only supports the
I2C interface and not the SPI interface.

The BME280, the one with humidity, is not fully tested at this point,
awaiting upon a breakout board and may not show proper humidity.

A driver for the Aosong AHT20 temperature and humidity sensor. While
slow for an I2C sensor it is inexpensive and should work well enough
in most indoor conditions. All features of the chip are supported.

Add sets-lists entries for the new combined midi_seq module

Add the new scsi_subr module to sets lists.

Create a loaable adiantum module, and make cgd require it.

This enablees use of a loadable cgd module, rather thtan requiring
it to be built-in.

Partially resolves kern/56772

Split i2c_subr.c into a separate module rather than including it in
the iic module. There are valid configurations where i2c_subr code
can be both built-in and part of a loaded module (eg, piixpm is in
the kernel, but the iic module is loaded later). This causes the
in-kernel linker to detect a duplicate symbol.

A driver and user land utility for the Sparkfun Serial Controlled Motor
Driver module as illustrated here:

https://www.sparkfun.com/products/13911

A SCMD module is a ARM SOC simular to a Arduino in front of a motor
driver chip. The single SCMD module can control two motors and up to
16 additional modules can be chained together using an internal I2C
bus. One can interface with the SCMD using tty uart commands, SPI or
I2C. The driver in this commit adds a kernel driver for the I2C and
SPI interfaces. The command line utility provides a set of
convenience commands that support most of the functions of the SCMD
and is able to use the tty uart mode, SPI user land or the included
kernel driver in a uniform manor.

The use of the SCMD module is mostly for small robots and the like,
but it can control anything that is controllable by voltage.

Driver for the Sensirion SHT30/SHT31/SHT35 temperature and humidity
sensor such as:

https://www.adafruit.com/product/2857

This is a higher priced sensor with a lot of features, including the
ability to do sub-second periodic updates. The driver supports
everything about the sensor except for the alert pin.

A driver for the Sensirion SGP40 MOx gas sensor. An example of this
chip from Adafruit is:

https://www.adafruit.com/product/4829

This is a moderately priced gas sensor that can detect volatile
organic compounds in the air. The driver uses the 3-clause BSD
licensed VOC algorithm provided by Sensirion to turn the raw sensor
metric into a VOC index which can indicate the quality of the air in a
particular indoor environment. All published functions of the chip
are supported and one unpublished feature.

A driver for the Sensirion SHT40/SHT41/SHT45 temperature and humidity
sensor. An example of this chip is:

https://www.adafruit.com/product/4885

This is a lower cost chip that provides higher then usual precision
according to the data sheet. This driver supports all of the published
functions that the chip has.

Build and install the if_run module. run(4) is not necessarily included
in all GENERIC kernels (as reported on libera IRC).

modules for if_wg, blake2s, libsodium

Add a new link-aggregation pseudo interface named lagg(4)

- FreeBSD's lagg(4) based implementation
- MP-safe and MP-scalable

branches: 1.143.2;
don't restrict pad module to i386 and amd64.

- module build tested on amiga, vax, i386, amd64, evbarm.
- build.sh release tested on i386.
- pad module functionality tested on aarch64.

branches: 1.142.2;
Add HAVE_NVMM and use it to control the build of NVMM related components.
Defined to "yes" on amd64, "no" everywhere else.

Remove if_iavf

Add if_iavf

Sort and deduplicate set lists.

Remove stale comments.

Add -unknown- to "./netbsd" in modules/mi to fix "build.sh syspkgs" failure

Infrastructure for putting kernel+modules in /netbsd/kernel and
/netbsd/modules respectively instead of /netbsd and
/stand/<arch>/<version>/modules. This is only supported for x86,
and is turned off by default. To try it, add KERNEL_DIR=yes in your
/mk.conf and install a system from that build.

remove SMBFS and nsmb/netsmb - userland part

if_ixl is MD

Make ixl(4) be able to build as a module

PR misc/46937: add modules package, from Lloyd Parkes.

Split the compat_50 module into two, separating the QUOTA-related
stuff from the rest of the module. This allows loading of the
(main) compat_50 module on kernels that don't include ``options
QUOTA''.

Welcome to 9.99.40 !

Addresses PR kern/54875

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

Ported driver for Intel Ethernet 700 series

reviewed by msaitoh and knakahara

Move dtrace_syscall_linux out of mi set list

Disable filemon.

It isn't suited for general use (that is, it poses security risks),
but the existence of the module means it is auto-loaded when /dev/filemon
is opened, which can be done by any user.

Thanks Ilja van Sprundel for the heads up.

Add a new member to struct vfsstat and grow the unused members
The new member is caled f_mntfromlabel and it is the dkw_wname
of the corresponding wedge. This is now used by df -W to display
the mountpoint name as NAME=

enable building modules for if_aue(4), if_cdce(4), if_cue(4),
if_kue(4), if_upl(4), if_url(4), and if_urndis(4)

Build an if_udav module (untested)

introduce a library of common code / backends to share code between
USB ethernet drivers.

usbnet.h introduces a new set of APIs to provide common solutions
for these driver features:
- USB endpoint pipe handling
- rx and tx chain handling
- generic handlers or support for several struct ifnet callbacks
- MII bus locking
- interrupt handling
- partial autoconf handling: much of attach, and detach/activate
can use common versions directly.

currently, only axen(4) and cdce(4) are converted. the reductions
in these drivers are quite significant: if_cdce.c is reduced from
1000 lines to 320 lines, and if_axen is reduced from 1902 lines
to 1021 lines.

add a "usbnet" module and make the if_axen module depend upon it.

branches: 1.122.2;
Update sets lists for new ufs module

Now that the if_srt module has a chance of working (ie, it now
actually attaches/detaches the cdevsw!), add the required srt
module to allow module autoload triggered by opening /dev/srtN

XXX As noted in the recent commit to if_srt.c, someone(tm) needs
XXX to create the /dev/srt* device nodes with major 179. :)

Add a loadable module for tap(4).

The code was already modularized, we simply didn't build the loadable
module.

Note also that since the tap(4) device can be reasonably accessed by
either creating a device instance (using ifconfig(8)) or by opening
/dev/tap, we need to create both if_tap.kmod and tap.kmod (similar to
what is done with tun(4)).

Add ure(4): RealTek RTL8152/RTL8153 10/100/Gigabit USB Ethernet device.
Ported from OpenBSD. Support for RX/TX checksum offload added by myself.

Merge the [pgoyette-compat] branch

Add mue(4), driver for Microchip LAN75xx/LAN78xx known as internal NIC of
Raspberry Pi 3 B+, from OpenBSD.

Tested on Raspberry Pi 3 B+ (LAN7800) and Z-TEK ZE582 (LAN7500).

* BUGS/TODO

- If the media type is set to something other than 1000baseT-FDX, data
transmission becomes quite unstable. Also, ukphy(4) recognize 1000baseT as
a supported media type, but it is not in fact.

- Catch up with changes made to usmsc(4) in nick-nhusb branch, i.e.,
make the driver MP-safe.

- Support RX/VLAN/TX chekcsum offloading.

branches: 1.116.2;
Add a 1PPS-over-GPIO driver, originally by Brad Spencer, with changes by
me to adapt to the new GPIO interrupt interface and support a wider variety
of GPIO pin configuations.

PR kern/51676

Add an example "gpioirq" driver that demonstrates interrupts on GPIO
pins. Will be enhanced in the future to support sending events to
user space on edge-triggered interrupt events.

Based on initial work by Brad Spencer.
PR kern/51676

branches: 1.114.2;
Merge autofs support from: Tomohiro Kusumi
XXX: Does not work yet

add new drivers, sort.

Split ip_ecn code into its own module, so it can be shared between
gif(4), stf(4), and ipsec(4). Without this, loading the if_gif
module can result in redefined global symbols if either ipsec(4) or
stf(4) but not gif(4) is built into the kernel.

Fixes PR kern/52795 (as reported by martin@ via irc).

XXX pullup to netbsd-8

Add new wsbell(4) module to the sets list.

branches: 1.110.2;
Update sets lists for new modules

Modularize ualea(4).

Unclear why we have a separate xyz.ioconf for module and XYZ.ioconf
for rump component, but at least xyz_modcmd obviates the need for
xyz_component.c (though evidently the latter could have been replaced
anyway by RUMP_COMPONENT=ioconf in the rump component Makefile).

add l2tp(4) L2TPv3 interface.

originally implemented by IIJ SEIL team.

branches: 1.107.2;
PR/51773: Yorick Hardy: drvctl module is not part of lvm

More sets list sorting (maybe this time they're really all done)

Restore the obsolete entries for spkr_synth, and mark the new spkr
module as not-obsolete.

Update for the new "universal" spkr module.

Note that entries in the md.i386 and md.amd64 lists are actually deleted
(rather than being marked "obsolete" as directed in the comments). This
is OK, since there is now a new module in the mi list to replace them.

delete spkr_synth

Create a new module for the synthesized speaker(4).

XXX Device module autoload (invoked when the /dev/speaker is opened, and
XXX no driver exists) will not find this module. On i386 and amd64, the
XXX autoload will find the spkr module (spkr0 at pcppi0) and that module
XXX will be autoloaded. For other architectures, either include the
XXX "spkr0 at audio0" in your config file, or manually load this new
XXX spkr_synth module using modload(8).

Update sets lists for new bufq_* modules

Update sets lists for new ptrace{,_common} modules

Missed the mlx_pci module in previous commit (to disable)

For now, disable all the newly-created ld(4) related modules. We need
to come up with a better way to handle attachment-specific modules, and
possibly a better directory structure for modules in general, as the
current mechanism doesn't scale.

Update sets lists for all the new modules (for l4(4) and its attachments)

Fix sets lists for nvme module. Since it is being built only for the
i386 and amd64 platforms, the entries belong in the md.xxx lists, not
in the mi list.

Add the new nvme module to the sets lists.

Update sets for new dummy "tun" module.

Sets for new modules

Modularize the pppoe driver

Modularize the sppp_subr stuff so it can be shared by pppoe and lmc
drivers as they get modularized.

sets for slip and strip

rename the ppp module so that it autoloads.

Modularize the ppp driver, and adjust dependencies of the compressor
modules.

For now, this is still included as a built-in module in GENERIC kernels.

Update sets lists for new slcompress module

branches: 1.86.2;
Update sets lists for new ipl (aka ipfilter) module.

Re-sort

Update sets for new i2c_bitbang and bpf_filter modules.

Descend into new raid module, and update sets lists.

Modularize drvctl(4)

Modularize the clockctl pseudo-device and link to the build.

Update sets list for merge of compat_sysv --> sysv_ipc

Add the newly-created wapbl module to the sets list.

Update sets lists for new sysv_ipc module

Additional commentary for where other duplicate entries might need to
be made (amd64-xen, i386-xen, and i386-xen-pae).

Update sets lists for new compat_sysv module.

Update sets lists for new sysmon modules

Update sets lists for new swwdog module

Add missing entries for dtrace modules to set lists.

add dtrace_lockstat

i2c devices don't actually have a dependency on "iic" (the bus driver)
but on "i2cexec". Create an i2cexec module (i2c_exec.c) to mirror the
dependencies in files.i2c and switch device drivers to depend on "i2cexec"
module instead.

A kernel with a USB stack and no I2C controller / bus attachment would spit
out a bunch of "WARNING: module error: can't find builtin dependency `iic'"
messages at boot. This change solves that problem.

Per the wiki roadmap, rename the three dtrace modules to have
a "dtrace_" prefix.
amd64 build tested, other set list changes done the same way.

branches: 1.69.2;
add hythygtemp module to set lists

sort

branches: 1.67.2;
Re-sort, and update md.evbppc for new crypto modules

Add new modules for opencrypto

Add new crypto algorithm modules to sets list

Add new zlib module

Add entries for new ccd module

Update sets lists for new modules.

Do not remove luacore entries, mark them as obsolete instead.

renamed luacore to luasystm

ubsec is not a MI buildable module. disable it for now.

Make ubsec(4) loadable as kmod.

Build a module for usmsc(4).

linke pmf(9l) to the build

link core(9l) (docs pending) to the build

link the lua(4) module to the build

Add driver for ASIX AX88178a and AX88179 Ethernet interface.
Ported from OpenBSD.

Sort entries in strcmp order.

more npf sets lossage.

Add entries for "cylic" and "profile" modules which are part of DTrace.

Add NPF "rndblock" extension to randomly drop packets (using a random function
with a percentage or modulo operation). This is a demo module, although it can
be used for packet loss simulation. Example of a procedure in npf.conf:

procedure "somedrop" {
# Drop 1.9% of the traffic
rndblock: percentage 1.9
}

Implement dynamic NPF extensions interface. An extension consists of
dynamically loaded module (.so) supplementing npfctl(8) and a kernel
module. Move normalisation and logging functionality into their own
extensions. More improvements to come.

branches: 1.47.2;
The hdaudio and hdafg modules are not MI (they at least require PCI)

Build hdaudio and hdafg modules.

Add distrib entries for new uatp module.

Hello, riastradh!

add vcoda module

Actually create the if_axe module - driver was modularized a while ago.

Actually create the dbcool(4) module. Driver was modularized a while ago.

Create the module for sdtemp (driver itself was modularized some time ago)

P1003_1B_SEMAPHORE is no longer optional.

branches: 1.39.2;
Set list fix...

add chfs.kmod

Build and install new in-kernel iscsi initiator kernel module and associated
binaries (iscsid, iscsictl) if MKISCSI != no. Initiator can also be built
into a kernel by adding 'pseudo-device iscsi' in kernel configuration.

Add entries for "npf_alg_icmp" kernel module.

Add "npf" kernel module.

branches: 1.34.2;
Build iic(4) and gpioiic(4) as modules.

Add filemon to the modules we build.

Link the gpioow(4) and onewire(4) modules to the build and add them to the
lists.

gpio(4) and gpiosim(4) can now be built and used as modules. While here,
make some functions static.

pwdog is not mi, but it only in the lists we build it for.

Fix a typo.

Add the pwdog module to md.evbppc as well and take a note in mi that
module have to be added in md.evbppc as well (and why that is so).

pwdog(4) is a device driver for QUANCOM Electronic PWDOG1 PCI
attached watchdog timers.

add dtv_math module

Ooopppsss - there were some other modules here that should not have been
committed. Remove them.

Add new spdmem(4) module

Add "v7fs" kernel module.

build dtv module

Import the Flash and NAND subsytem code contributed by the University
of Szeged, Hungary.

The commit includes:
- Flash layer, which gives a common API to access flash devices
- NAND controller subsystem for the flash layer
- An example OMAP driver which is used on BeagleBoard or alike ARM boards

branches: 1.20.2;
some platforms don't have bus_dma, so only build these modules on x86

hook xc5k, au8522, and auvitek into build

Build the new swsensor(4) device and add to set lists

Extract MIIVERBOSE into a kernel module. The module can be builtin
by defining 'options MIIVERBOSE' in the kernel config file (no change
from current behavior), or it can be loaded at boot time on those
architectures that support the boot loader's "load" command.

Extract SCSIVERBOSE into a kernel module. The module can be builtin
by defining 'options SCSIVERBOSE' in the kernel config file (no change
from current behavior), or it can be loaded at boot time on those
architectures that support the boot loader's "load" command.

The module is built for all architectures, whether or not SCSI or
atapi support exists.

Extract USBVERBOSE into a kernel module. The module can be builtin
by defining 'options USBVERBOSE' in the kernel config file (no change
from current behavior), or it can be loaded at boot time on those
architectures that support the boot loader's "load" command.

The module is built for all architectures, whether or not USB support
exists.

Extract the vendor/product tables and related access routines into a
separate kernel module. Update pci bus attach routine to load the
module (if available) when we're about to start scanning the bus, and
unload the module after the scan is finished.

On architectures which support loading of modules by the boot loader,
the 'pciverbose' module can be loaded and executed without needing to
rebuild the kernel. On all architectures, using 'options PCIVERBOSE'
in the kernel configuration file will create a 'builtin' module which
is functionally equivalent to previous behavior.

XXX Although not nearly as large as the vendor and product tables,
XXX the PCI class and subclass tables might also be offloaded into
XXX the module at a future time.

XXX Cardbus (and possibly other) drivers should also be modified to
XXX load the module before scanning/attaching devices.

Add pf to the module set list.

DTrace: Add the Function Boundary Trace (FBT) provider moduile. This
module instruments every function in the kernel with entry and exit
probes. These probes are true zero-effect probes in that they don't
exist in the code until they are enabled. The probes are enabled by
directly patching the function entry and exit points to make jumps into
the dtrace framework.
This gives us over 29,000 trace points in the kernel.

"dtrace,zfs" means "MKDTRACE=yes" *and* "MKZFS=yes" which is not what
we want. Invent a flag "solaris" which is the or of those two flags.

The directory "modules/solaris" depends on ZFS as well.

The "solaris" kernel module also gets build if ZFS is enabled.

DTrace: Add an SDT (Statically Defined Tracing) provider framework, and
implement most of the proc provider. Adds proc:::create, exec,
exec_success, exec_faillure, signal_send, signal_discard, signal_handle,
lwp_create, lwp_start, lwp_exit.

Add DTrace to sets.

add bpf kmod

Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Add zfs sets and needed veriables to hook zfs into the build. ZFS on i386
need still one fix othervise it should be ready for testing.

First part of secmodel cleanup and other misc. changes:

- Separate the suser part of the bsd44 secmodel into its own secmodel
and directory, pending even more cleanups. For revision history
purposes, the original location of the files was

src/sys/secmodel/bsd44/secmodel_bsd44_suser.c
src/sys/secmodel/bsd44/suser.h

- Add a man-page for secmodel_suser(9) and update the one for
secmodel_bsd44(9).

- Add a "secmodel" module class and use it. Userland program and
documentation updated.

- Manage secmodel count (nsecmodels) through the module framework.
This eliminates the need for secmodel_{,de}register() calls in
secmodel code.

- Prepare for secmodel modularization by adding relevant module bits.
The secmodels don't allow auto unload. The bsd44 secmodel depends
on the suser and securelevel secmodels. The overlay secmodel depends
on the bsd44 secmodel. As the module class is only cosmetic, and to
prevent ambiguity, the bsd44 and overlay secmodels are prefixed with
"secmodel_".

- Adapt the overlay secmodel to recent changes (mainly vnode scope).

- Stop using link-sets for the sysctl node(s) creation.

- Keep sysctl variables under nodes of their relevant secmodels. In
other words, don't create duplicates for the suser/securelevel
secmodels under the bsd44 secmodel, as the latter is merely used
for "grouping".

- For the suser and securelevel secmodels, "advertise presence" in
relevant sysctl nodes (sysctl.security.models.{suser,securelevel}).

- Get rid of the LKM preprocessor stuff.

- As secmodels are now modules, there's no need for an explicit call
to secmodel_start(); it's handled by the module framework. That
said, the module framework was adjusted to properly load secmodels
early during system startup.

- Adapt rump to changes: Instead of using empty stubs for securelevel,
simply use the suser secmodel. Also replace secmodel_start() with a
call to secmodel_suser_start().

- 5.99.20.

Testing was done on i386 ("release" build). Spearated module_init()
changes were tested on sparc and sparc64 as well by martin@ (thanks!).

Mailing list reference:

http://mail-index.netbsd.org/tech-kern/2009/09/25/msg006135.html

add ./etc/mtree/set.modules so that modules.tgz is created with
actual files in it, rather than a 20 byte .gz file (ie, empty file.)


HI JNEMETH!

Create a modules.tgz set and move kernel modules into it.

make owtemp a module

add compat_100 module setlist entries

Split the BMP280 / BME280 driver into common code and create I2C and
SPI attachments.

A driver for the Bosch BMP280 / BME280 temperature, humidity and
atmospheric pressure sensor. This is an inexpensive to moderately
expensive chip available from a large number of places. The driver
supports all aspects of the two chips, except for the repeating read
mode which would allow for sub-second queries, such as fall detection
or perhaps even as an altimeter. This driver also only supports the
I2C interface and not the SPI interface.

The BME280, the one with humidity, is not fully tested at this point,
awaiting upon a breakout board and may not show proper humidity.

A driver for the Aosong AHT20 temperature and humidity sensor. While
slow for an I2C sensor it is inexpensive and should work well enough
in most indoor conditions. All features of the chip are supported.

Add sets-lists entries for the new combined midi_seq module

Add the new scsi_subr module to sets lists.

Create a loaable adiantum module, and make cgd require it.

This enablees use of a loadable cgd module, rather thtan requiring
it to be built-in.

Partially resolves kern/56772

Split i2c_subr.c into a separate module rather than including it in
the iic module. There are valid configurations where i2c_subr code
can be both built-in and part of a loaded module (eg, piixpm is in
the kernel, but the iic module is loaded later). This causes the
in-kernel linker to detect a duplicate symbol.

A driver and user land utility for the Sparkfun Serial Controlled Motor
Driver module as illustrated here:

https://www.sparkfun.com/products/13911

A SCMD module is a ARM SOC simular to a Arduino in front of a motor
driver chip. The single SCMD module can control two motors and up to
16 additional modules can be chained together using an internal I2C
bus. One can interface with the SCMD using tty uart commands, SPI or
I2C. The driver in this commit adds a kernel driver for the I2C and
SPI interfaces. The command line utility provides a set of
convenience commands that support most of the functions of the SCMD
and is able to use the tty uart mode, SPI user land or the included
kernel driver in a uniform manor.

The use of the SCMD module is mostly for small robots and the like,
but it can control anything that is controllable by voltage.

Driver for the Sensirion SHT30/SHT31/SHT35 temperature and humidity
sensor such as:

https://www.adafruit.com/product/2857

This is a higher priced sensor with a lot of features, including the
ability to do sub-second periodic updates. The driver supports
everything about the sensor except for the alert pin.

A driver for the Sensirion SGP40 MOx gas sensor. An example of this
chip from Adafruit is:

https://www.adafruit.com/product/4829

This is a moderately priced gas sensor that can detect volatile
organic compounds in the air. The driver uses the 3-clause BSD
licensed VOC algorithm provided by Sensirion to turn the raw sensor
metric into a VOC index which can indicate the quality of the air in a
particular indoor environment. All published functions of the chip
are supported and one unpublished feature.

A driver for the Sensirion SHT40/SHT41/SHT45 temperature and humidity
sensor. An example of this chip is:

https://www.adafruit.com/product/4885

This is a lower cost chip that provides higher then usual precision
according to the data sheet. This driver supports all of the published
functions that the chip has.

Build and install the if_run module. run(4) is not necessarily included
in all GENERIC kernels (as reported on libera IRC).

modules for if_wg, blake2s, libsodium

Add a new link-aggregation pseudo interface named lagg(4)

- FreeBSD's lagg(4) based implementation
- MP-safe and MP-scalable

branches: 1.143.2;
don't restrict pad module to i386 and amd64.

- module build tested on amiga, vax, i386, amd64, evbarm.
- build.sh release tested on i386.
- pad module functionality tested on aarch64.

branches: 1.142.2;
Add HAVE_NVMM and use it to control the build of NVMM related components.
Defined to "yes" on amd64, "no" everywhere else.

Remove if_iavf

Add if_iavf

Sort and deduplicate set lists.

Remove stale comments.

Add -unknown- to "./netbsd" in modules/mi to fix "build.sh syspkgs" failure

Infrastructure for putting kernel+modules in /netbsd/kernel and
/netbsd/modules respectively instead of /netbsd and
/stand/<arch>/<version>/modules. This is only supported for x86,
and is turned off by default. To try it, add KERNEL_DIR=yes in your
/mk.conf and install a system from that build.

remove SMBFS and nsmb/netsmb - userland part

if_ixl is MD

Make ixl(4) be able to build as a module

PR misc/46937: add modules package, from Lloyd Parkes.

Split the compat_50 module into two, separating the QUOTA-related
stuff from the rest of the module. This allows loading of the
(main) compat_50 module on kernels that don't include ``options
QUOTA''.

Welcome to 9.99.40 !

Addresses PR kern/54875

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

Ported driver for Intel Ethernet 700 series

reviewed by msaitoh and knakahara

Move dtrace_syscall_linux out of mi set list

Disable filemon.

It isn't suited for general use (that is, it poses security risks),
but the existence of the module means it is auto-loaded when /dev/filemon
is opened, which can be done by any user.

Thanks Ilja van Sprundel for the heads up.

Add a new member to struct vfsstat and grow the unused members
The new member is caled f_mntfromlabel and it is the dkw_wname
of the corresponding wedge. This is now used by df -W to display
the mountpoint name as NAME=

enable building modules for if_aue(4), if_cdce(4), if_cue(4),
if_kue(4), if_upl(4), if_url(4), and if_urndis(4)

Build an if_udav module (untested)

introduce a library of common code / backends to share code between
USB ethernet drivers.

usbnet.h introduces a new set of APIs to provide common solutions
for these driver features:
- USB endpoint pipe handling
- rx and tx chain handling
- generic handlers or support for several struct ifnet callbacks
- MII bus locking
- interrupt handling
- partial autoconf handling: much of attach, and detach/activate
can use common versions directly.

currently, only axen(4) and cdce(4) are converted. the reductions
in these drivers are quite significant: if_cdce.c is reduced from
1000 lines to 320 lines, and if_axen is reduced from 1902 lines
to 1021 lines.

add a "usbnet" module and make the if_axen module depend upon it.

branches: 1.122.2;
Update sets lists for new ufs module

Now that the if_srt module has a chance of working (ie, it now
actually attaches/detaches the cdevsw!), add the required srt
module to allow module autoload triggered by opening /dev/srtN

XXX As noted in the recent commit to if_srt.c, someone(tm) needs
XXX to create the /dev/srt* device nodes with major 179. :)

Add a loadable module for tap(4).

The code was already modularized, we simply didn't build the loadable
module.

Note also that since the tap(4) device can be reasonably accessed by
either creating a device instance (using ifconfig(8)) or by opening
/dev/tap, we need to create both if_tap.kmod and tap.kmod (similar to
what is done with tun(4)).

Add ure(4): RealTek RTL8152/RTL8153 10/100/Gigabit USB Ethernet device.
Ported from OpenBSD. Support for RX/TX checksum offload added by myself.

Merge the [pgoyette-compat] branch

Add mue(4), driver for Microchip LAN75xx/LAN78xx known as internal NIC of
Raspberry Pi 3 B+, from OpenBSD.

Tested on Raspberry Pi 3 B+ (LAN7800) and Z-TEK ZE582 (LAN7500).

* BUGS/TODO

- If the media type is set to something other than 1000baseT-FDX, data
transmission becomes quite unstable. Also, ukphy(4) recognize 1000baseT as
a supported media type, but it is not in fact.

- Catch up with changes made to usmsc(4) in nick-nhusb branch, i.e.,
make the driver MP-safe.

- Support RX/VLAN/TX chekcsum offloading.

branches: 1.116.2;
Add a 1PPS-over-GPIO driver, originally by Brad Spencer, with changes by
me to adapt to the new GPIO interrupt interface and support a wider variety
of GPIO pin configuations.

PR kern/51676

Add an example "gpioirq" driver that demonstrates interrupts on GPIO
pins. Will be enhanced in the future to support sending events to
user space on edge-triggered interrupt events.

Based on initial work by Brad Spencer.
PR kern/51676

branches: 1.114.2;
Merge autofs support from: Tomohiro Kusumi
XXX: Does not work yet

add new drivers, sort.

Split ip_ecn code into its own module, so it can be shared between
gif(4), stf(4), and ipsec(4). Without this, loading the if_gif
module can result in redefined global symbols if either ipsec(4) or
stf(4) but not gif(4) is built into the kernel.

Fixes PR kern/52795 (as reported by martin@ via irc).

XXX pullup to netbsd-8

Add new wsbell(4) module to the sets list.

branches: 1.110.2;
Update sets lists for new modules

Modularize ualea(4).

Unclear why we have a separate xyz.ioconf for module and XYZ.ioconf
for rump component, but at least xyz_modcmd obviates the need for
xyz_component.c (though evidently the latter could have been replaced
anyway by RUMP_COMPONENT=ioconf in the rump component Makefile).

add l2tp(4) L2TPv3 interface.

originally implemented by IIJ SEIL team.

branches: 1.107.2;
PR/51773: Yorick Hardy: drvctl module is not part of lvm

More sets list sorting (maybe this time they're really all done)

Restore the obsolete entries for spkr_synth, and mark the new spkr
module as not-obsolete.

Update for the new "universal" spkr module.

Note that entries in the md.i386 and md.amd64 lists are actually deleted
(rather than being marked "obsolete" as directed in the comments). This
is OK, since there is now a new module in the mi list to replace them.

delete spkr_synth

Create a new module for the synthesized speaker(4).

XXX Device module autoload (invoked when the /dev/speaker is opened, and
XXX no driver exists) will not find this module. On i386 and amd64, the
XXX autoload will find the spkr module (spkr0 at pcppi0) and that module
XXX will be autoloaded. For other architectures, either include the
XXX "spkr0 at audio0" in your config file, or manually load this new
XXX spkr_synth module using modload(8).

Update sets lists for new bufq_* modules

Update sets lists for new ptrace{,_common} modules

Missed the mlx_pci module in previous commit (to disable)

For now, disable all the newly-created ld(4) related modules. We need
to come up with a better way to handle attachment-specific modules, and
possibly a better directory structure for modules in general, as the
current mechanism doesn't scale.

Update sets lists for all the new modules (for l4(4) and its attachments)

Fix sets lists for nvme module. Since it is being built only for the
i386 and amd64 platforms, the entries belong in the md.xxx lists, not
in the mi list.

Add the new nvme module to the sets lists.

Update sets for new dummy "tun" module.

Sets for new modules

Modularize the pppoe driver

Modularize the sppp_subr stuff so it can be shared by pppoe and lmc
drivers as they get modularized.

sets for slip and strip

rename the ppp module so that it autoloads.

Modularize the ppp driver, and adjust dependencies of the compressor
modules.

For now, this is still included as a built-in module in GENERIC kernels.

Update sets lists for new slcompress module

branches: 1.86.2;
Update sets lists for new ipl (aka ipfilter) module.

Re-sort

Update sets for new i2c_bitbang and bpf_filter modules.

Descend into new raid module, and update sets lists.

Modularize drvctl(4)

Modularize the clockctl pseudo-device and link to the build.

Update sets list for merge of compat_sysv --> sysv_ipc

Add the newly-created wapbl module to the sets list.

Update sets lists for new sysv_ipc module

Additional commentary for where other duplicate entries might need to
be made (amd64-xen, i386-xen, and i386-xen-pae).

Update sets lists for new compat_sysv module.

Update sets lists for new sysmon modules

Update sets lists for new swwdog module

Add missing entries for dtrace modules to set lists.

add dtrace_lockstat

i2c devices don't actually have a dependency on "iic" (the bus driver)
but on "i2cexec". Create an i2cexec module (i2c_exec.c) to mirror the
dependencies in files.i2c and switch device drivers to depend on "i2cexec"
module instead.

A kernel with a USB stack and no I2C controller / bus attachment would spit
out a bunch of "WARNING: module error: can't find builtin dependency `iic'"
messages at boot. This change solves that problem.

Per the wiki roadmap, rename the three dtrace modules to have
a "dtrace_" prefix.
amd64 build tested, other set list changes done the same way.

branches: 1.69.2;
add hythygtemp module to set lists

sort

branches: 1.67.2;
Re-sort, and update md.evbppc for new crypto modules

Add new modules for opencrypto

Add new crypto algorithm modules to sets list

Add new zlib module

Add entries for new ccd module

Update sets lists for new modules.

Do not remove luacore entries, mark them as obsolete instead.

renamed luacore to luasystm

ubsec is not a MI buildable module. disable it for now.

Make ubsec(4) loadable as kmod.

Build a module for usmsc(4).

linke pmf(9l) to the build

link core(9l) (docs pending) to the build

link the lua(4) module to the build

Add driver for ASIX AX88178a and AX88179 Ethernet interface.
Ported from OpenBSD.

Sort entries in strcmp order.

more npf sets lossage.

Add entries for "cylic" and "profile" modules which are part of DTrace.

Add NPF "rndblock" extension to randomly drop packets (using a random function
with a percentage or modulo operation). This is a demo module, although it can
be used for packet loss simulation. Example of a procedure in npf.conf:

procedure "somedrop" {
# Drop 1.9% of the traffic
rndblock: percentage 1.9
}

Implement dynamic NPF extensions interface. An extension consists of
dynamically loaded module (.so) supplementing npfctl(8) and a kernel
module. Move normalisation and logging functionality into their own
extensions. More improvements to come.

branches: 1.47.2;
The hdaudio and hdafg modules are not MI (they at least require PCI)

Build hdaudio and hdafg modules.

Add distrib entries for new uatp module.

Hello, riastradh!

add vcoda module

Actually create the if_axe module - driver was modularized a while ago.

Actually create the dbcool(4) module. Driver was modularized a while ago.

Create the module for sdtemp (driver itself was modularized some time ago)

P1003_1B_SEMAPHORE is no longer optional.

branches: 1.39.2;
Set list fix...

add chfs.kmod

Build and install new in-kernel iscsi initiator kernel module and associated
binaries (iscsid, iscsictl) if MKISCSI != no. Initiator can also be built
into a kernel by adding 'pseudo-device iscsi' in kernel configuration.

Add entries for "npf_alg_icmp" kernel module.

Add "npf" kernel module.

branches: 1.34.2;
Build iic(4) and gpioiic(4) as modules.

Add filemon to the modules we build.

Link the gpioow(4) and onewire(4) modules to the build and add them to the
lists.

gpio(4) and gpiosim(4) can now be built and used as modules. While here,
make some functions static.

pwdog is not mi, but it only in the lists we build it for.

Fix a typo.

Add the pwdog module to md.evbppc as well and take a note in mi that
module have to be added in md.evbppc as well (and why that is so).

pwdog(4) is a device driver for QUANCOM Electronic PWDOG1 PCI
attached watchdog timers.

add dtv_math module

Ooopppsss - there were some other modules here that should not have been
committed. Remove them.

Add new spdmem(4) module

Add "v7fs" kernel module.

build dtv module

Import the Flash and NAND subsytem code contributed by the University
of Szeged, Hungary.

The commit includes:
- Flash layer, which gives a common API to access flash devices
- NAND controller subsystem for the flash layer
- An example OMAP driver which is used on BeagleBoard or alike ARM boards

branches: 1.20.2;
some platforms don't have bus_dma, so only build these modules on x86

hook xc5k, au8522, and auvitek into build

Build the new swsensor(4) device and add to set lists

Extract MIIVERBOSE into a kernel module. The module can be builtin
by defining 'options MIIVERBOSE' in the kernel config file (no change
from current behavior), or it can be loaded at boot time on those
architectures that support the boot loader's "load" command.

Extract SCSIVERBOSE into a kernel module. The module can be builtin
by defining 'options SCSIVERBOSE' in the kernel config file (no change
from current behavior), or it can be loaded at boot time on those
architectures that support the boot loader's "load" command.

The module is built for all architectures, whether or not SCSI or
atapi support exists.

Extract USBVERBOSE into a kernel module. The module can be builtin
by defining 'options USBVERBOSE' in the kernel config file (no change
from current behavior), or it can be loaded at boot time on those
architectures that support the boot loader's "load" command.

The module is built for all architectures, whether or not USB support
exists.

Extract the vendor/product tables and related access routines into a
separate kernel module. Update pci bus attach routine to load the
module (if available) when we're about to start scanning the bus, and
unload the module after the scan is finished.

On architectures which support loading of modules by the boot loader,
the 'pciverbose' module can be loaded and executed without needing to
rebuild the kernel. On all architectures, using 'options PCIVERBOSE'
in the kernel configuration file will create a 'builtin' module which
is functionally equivalent to previous behavior.

XXX Although not nearly as large as the vendor and product tables,
XXX the PCI class and subclass tables might also be offloaded into
XXX the module at a future time.

XXX Cardbus (and possibly other) drivers should also be modified to
XXX load the module before scanning/attaching devices.

Add pf to the module set list.

DTrace: Add the Function Boundary Trace (FBT) provider moduile. This
module instruments every function in the kernel with entry and exit
probes. These probes are true zero-effect probes in that they don't
exist in the code until they are enabled. The probes are enabled by
directly patching the function entry and exit points to make jumps into
the dtrace framework.
This gives us over 29,000 trace points in the kernel.

"dtrace,zfs" means "MKDTRACE=yes" *and* "MKZFS=yes" which is not what
we want. Invent a flag "solaris" which is the or of those two flags.

The directory "modules/solaris" depends on ZFS as well.

The "solaris" kernel module also gets build if ZFS is enabled.

DTrace: Add an SDT (Statically Defined Tracing) provider framework, and
implement most of the proc provider. Adds proc:::create, exec,
exec_success, exec_faillure, signal_send, signal_discard, signal_handle,
lwp_create, lwp_start, lwp_exit.

Add DTrace to sets.

add bpf kmod

Remove the portalfs kernel file system driver. Replace mount_portal(8)
with a version based on puffs. User functionality remains the same.

Add zfs sets and needed veriables to hook zfs into the build. ZFS on i386
need still one fix othervise it should be ready for testing.

First part of secmodel cleanup and other misc. changes:

- Separate the suser part of the bsd44 secmodel into its own secmodel
and directory, pending even more cleanups. For revision history
purposes, the original location of the files was

src/sys/secmodel/bsd44/secmodel_bsd44_suser.c
src/sys/secmodel/bsd44/suser.h

- Add a man-page for secmodel_suser(9) and update the one for
secmodel_bsd44(9).

- Add a "secmodel" module class and use it. Userland program and
documentation updated.

- Manage secmodel count (nsecmodels) through the module framework.
This eliminates the need for secmodel_{,de}register() calls in
secmodel code.

- Prepare for secmodel modularization by adding relevant module bits.
The secmodels don't allow auto unload. The bsd44 secmodel depends
on the suser and securelevel secmodels. The overlay secmodel depends
on the bsd44 secmodel. As the module class is only cosmetic, and to
prevent ambiguity, the bsd44 and overlay secmodels are prefixed with
"secmodel_".

- Adapt the overlay secmodel to recent changes (mainly vnode scope).

- Stop using link-sets for the sysctl node(s) creation.

- Keep sysctl variables under nodes of their relevant secmodels. In
other words, don't create duplicates for the suser/securelevel
secmodels under the bsd44 secmodel, as the latter is merely used
for "grouping".

- For the suser and securelevel secmodels, "advertise presence" in
relevant sysctl nodes (sysctl.security.models.{suser,securelevel}).

- Get rid of the LKM preprocessor stuff.

- As secmodels are now modules, there's no need for an explicit call
to secmodel_start(); it's handled by the module framework. That
said, the module framework was adjusted to properly load secmodels
early during system startup.

- Adapt rump to changes: Instead of using empty stubs for securelevel,
simply use the suser secmodel. Also replace secmodel_start() with a
call to secmodel_suser_start().

- 5.99.20.

Testing was done on i386 ("release" build). Spearated module_init()
changes were tested on sparc and sparc64 as well by martin@ (thanks!).

Mailing list reference:

http://mail-index.netbsd.org/tech-kern/2009/09/25/msg006135.html

add ./etc/mtree/set.modules so that modules.tgz is created with
actual files in it, rather than a 20 byte .gz file (ie, empty file.)


HI JNEMETH!

Create a modules.tgz set and move kernel modules into it.

add compat_100 module setlist entries

Split the BMP280 / BME280 driver into common code and create I2C and
SPI attachments.

A driver for the Bosch BMP280 / BME280 temperature, humidity and
atmospheric pressure sensor. This is an inexpensive to moderately
expensive chip available from a large number of places. The driver
supports all aspects of the two chips, except for the repeating read
mode which would allow for sub-second queries, such as fall detection
or perhaps even as an altimeter. This driver also only supports the
I2C interface and not the SPI interface.

The BME280, the one with humidity, is not fully tested at this point,
awaiting upon a breakout board and may not show proper humidity.

A driver for the Aosong AHT20 temperature and humidity sensor. While
slow for an I2C sensor it is inexpensive and should work well enough
in most indoor conditions. All features of the chip are supported.

Add sets-lists entries for the new combined midi_seq module

Add the new scsi_subr module to sets lists.

Create a loaable adiantum module, and make cgd require it.

This enablees use of a loadable cgd module, rather thtan requiring
it to be built-in.

Partially resolves kern/56772

Split i2c_subr.c into a separate module rather than including it in
the iic module. There are valid configurations where i2c_subr code
can be both built-in and part of a loaded module (eg, piixpm is in
the kernel, but the iic module is loaded later). This causes the
in-kernel linker to detect a duplicate symbol.

A driver and user land utility for the Sparkfun Serial Controlled Motor
Driver module as illustrated here:

https://www.sparkfun.com/products/13911

A SCMD module is a ARM SOC simular to a Arduino in front of a motor
driver chip. The single SCMD module can control two motors and up to
16 additional modules can be chained together using an internal I2C
bus. One can interface with the SCMD using tty uart commands, SPI or
I2C. The driver in this commit adds a kernel driver for the I2C and
SPI interfaces. The command line utility provides a set of
convenience commands that support most of the functions of the SCMD
and is able to use the tty uart mode, SPI user land or the included
kernel driver in a uniform manor.

The use of the SCMD module is mostly for small robots and the like,
but it can control anything that is controllable by voltage.

Driver for the Sensirion SHT30/SHT31/SHT35 temperature and humidity
sensor such as:

https://www.adafruit.com/product/2857

This is a higher priced sensor with a lot of features, including the
ability to do sub-second periodic updates. The driver supports
everything about the sensor except for the alert pin.

A driver for the Sensirion SGP40 MOx gas sensor. An example of this
chip from Adafruit is:

https://www.adafruit.com/product/4829

This is a moderately priced gas sensor that can detect volatile
organic compounds in the air. The driver uses the 3-clause BSD
licensed VOC algorithm provided by Sensirion to turn the raw sensor
metric into a VOC index which can indicate the quality of the air in a
particular indoor environment. All published functions of the chip
are supported and one unpublished feature.

A driver for the Sensirion SHT40/SHT41/SHT45 temperature and humidity
sensor. An example of this chip is:

https://www.adafruit.com/product/4885

This is a lower cost chip that provides higher then usual precision
according to the data sheet. This driver supports all of the published
functions that the chip has.

Build and install the if_run module. run(4) is not necessarily included
in all GENERIC kernels (as reported on libera IRC).

modules for if_wg, blake2s, libsodium

Add a new link-aggregation pseudo interface named lagg(4)

- FreeBSD's lagg(4) based implementation
- MP-safe and MP-scalable

branches: 1.143.2;
don't restrict pad module to i386 and amd64.

- module build tested on amiga, vax, i386, amd64, evbarm.
- build.sh release tested on i386.
- pad module functionality tested on aarch64.

branches: 1.142.2;
Add HAVE_NVMM and use it to control the build of NVMM related components.
Defined to "yes" on amd64, "no" everywhere else.

Remove if_iavf

Add if_iavf

Sort and deduplicate set lists.

Remove stale comments.

Add -unknown- to "./netbsd" in modules/mi to fix "build.sh syspkgs" failure

Infrastructure for putting kernel+modules in /netbsd/kernel and
/netbsd/modules respectively instead of /netbsd and
/stand/<arch>/<version>/modules. This is only supported for x86,
and is turned off by default. To try it, add KERNEL_DIR=yes in your
/mk.conf and install a system from that build.

remove SMBFS and nsmb/netsmb - userland part

if_ixl is MD

Make ixl(4) be able to build as a module

PR misc/46937: add modules package, from Lloyd Parkes.

Split the compat_50 module into two, separating the QUOTA-related
stuff from the rest of the module. This allows loading of the
(main) compat_50 module on kernels that don't include ``options
QUOTA''.

Welcome to 9.99.40 !

Addresses PR kern/54875

Remove the strip(4) - Starmode Radio IP - pseudo-device driver. It is
long since obsolete.

Ported driver for Intel Ethernet 700 series

reviewed by msaitoh and knakahara

Move dtrace_syscall_linux out of mi set list

Disable filemon.

It isn't suited for general use (that is, it poses security risks),
but the existence of the module means it is auto-loaded when /dev/filemon
is opened, which can be done by any user.

Thanks Ilja van Sprundel for the heads up.

Add a new member to struct vfsstat and grow the unused members
The new member is caled f_mntfromlabel and it is the dkw_wname
of the corresponding wedge. This is now used by df -W to display
the mountpoint name as NAME=

enable building modules for if_aue(4), if_cdce(4), if_cue(4),
if_kue(4), if_upl(4), if_url(4), and if_urndis(4)

Build an if_udav module (untested)

introduce a library of common code / backends to share code between
USB ethernet drivers.

usbnet.h introduces a new set of APIs to provide common solutions
for these driver features:
- USB endpoint pipe handling
- rx and tx chain handling
- generic handlers or support for several struct ifnet callbacks
- MII bus locking
- interrupt handling
- partial autoconf handling: much of attach, and detach/activate
can use common versions directly.

currently, only axen(4) and cdce(4) are converted. the reductions
in these drivers are quite significant: if_cdce.c is reduced from
1000 lines to 320 lines, and if_axen is reduced from 1902 lines
to 1021 lines.

add a "usbnet" module and make the if_axen module depend upon it.

branches: 1.122.2;
Update sets lists for new ufs module

Now that the if_srt module has a chance of working (ie, it now
actually attaches/detaches the cdevsw!), add the required srt
module to allow module autoload triggered by opening /dev/srtN

XXX As noted in the recent commit to if_srt.c, someone(tm) needs
XXX to create the /dev/srt* device nodes with major 179. :)

Add a loadable module for tap(4).

The code was already modularized, we simply didn't build the loadable
module.

Note also that since the tap(4) device can be reasonably accessed by
either creating a device instance (using ifconfig(8)) or by opening
/dev/tap, we need to create both if_tap.kmod and tap.kmod (similar to
what is done with tun(4)).

Add ure(4): RealTek RTL8152/RTL8153 10/100/Gigabit USB Ethernet device.
Ported from OpenBSD. Support for RX/TX checksum offload added by myself.

Merge the [pgoyette-compat] branch

Add mue(4), driver for Microchip LAN75xx/LAN78xx known as internal NIC of
Raspberry Pi 3 B+, from OpenBSD.

Tested on Raspberry Pi 3 B+ (LAN7800) and Z-TEK ZE582 (LAN7500).

* BUGS/TODO

- If the media type is set to something other than 1000baseT-FDX, data
transmission becomes quite unstable. Also, ukphy(4) recognize 1000baseT as
a supported media type, but it is not in fact.

- Catch up with changes made to usmsc(4) in nick-nhusb branch, i.e.,
make the driver MP-safe.

- Support RX/VLAN/TX chekcsum offloading.

branches: 1.116.2;
Add a 1PPS-over-GPIO driver, originally by Brad Spencer, with changes by
me to adapt to the new GPIO interrupt interface and support a wider variety
of GPIO pin configuations.

PR kern/51676

Add an example "gpioirq" driver that demonstrates interrupts on GPIO
pins. Will be enhanced in the future to support sending events to
user space on edge-triggered interrupt events.

Based on initial work by Brad Spencer.
PR kern/51676

branches: 1.114.2;
Merge autofs support from: Tomohiro Kusumi
XXX: Does not work yet

add new drivers, sort.

Split ip_ecn code into its own module, so it can be shared between
gif(4), stf(4), and ipsec(4). Without this, loading the if_gif
module can result in redefined global symbols if either ipsec(4) or
stf(4) but not gif(4) is built into the kernel.

Fixes PR kern/52795 (as reported by martin@ via irc).

XXX pullup to netbsd-8

Add new wsbell(4) module to the sets list.

branches: 1.110.2;
Update sets lists for new modules

Modularize ualea(4).

Unclear why we have a separate xyz.ioconf for module and XYZ.ioconf
for rump component, but at least xyz_modcmd obviates the need for
xyz_component.c (though evidently the latter could have been replaced
anyway by RUMP_COMPONENT=ioconf in the rump component Makefile).

add l2tp(4) L2TPv3 interface.

originally implemented by IIJ SEIL team.

branches: 1.107.2;
PR/51773: Yorick Hardy: drvctl module is not part of lvm

More sets list sorting (maybe this time they're really all done)

Restore the obsolete entries for spkr_synth, and mark the new spkr
module as not-obsolete.

Update for the new "universal" spkr module.

Note that entries in the md.i386 and md.amd64 lists are actually deleted
(rather than being marked "obsolete" as directed in the comments). This
is OK, since there is now a new module in the mi list to replace them.

delete spkr_synth

Create a new module for the synthesized speaker(4).

XXX Device module autoload (invoked when the /dev/speaker is opened, and
XXX no driver exists) will not find this module. On i386 and amd64, the
XXX autoload will find the spkr module (spkr0 at pcppi0) and that module
XXX will be autoloaded. For other architectures, either include the
XXX "spkr0 at audio0" in your config file, or manually load this new
XXX spkr_synth module using modload(8).

Update sets lists for new bufq_* modules

Update sets lists for new ptrace{,_common} modules

Missed the mlx_pci module in previous commit (to disable)

For now, disable all the newly-created ld(4) related modules. We need
to come up with a better way to handle attachment-specific modules, and
possibly a better directory structure for modules in general, as the
current mechanism doesn't scale.

Update sets lists for all the new modules (for l4(4) and its attachments)

Fix sets lists for nvme module. Since it is being built only for the
i386 and amd64 platforms, the entries belong in the md.xxx lists, not
in the mi list.

Add the new nvme module to the sets lists.

Update sets for new dummy "tun" module.

Sets for new modules

Modularize the pppoe driver

Modularize the sppp_subr stuff so it can be shared by pppoe and lmc
drivers as they get modularized.

sets for slip and strip

rename the ppp module so that it autoloads.

Modularize the ppp driver, and adjust dependencies of the compressor
modules.

For now, this is still included as a built-in module in GENERIC kernels.

Update sets lists for new slcompress module

branches: 1.86.2;
Update sets lists for new ipl (aka ipfilter) module.

Re-sort

Update sets for new i2c_bitbang and bpf_filter modules.

Descend into new raid module, and update sets lists.

Modularize drvctl(4)

Modularize the clockctl pseudo-device and link to the build.

Update sets list for merge of compat_sysv --> sysv_ipc

Add the newly-created wapbl module to the sets list.

Update sets lists for new sysv_ipc module

Additional commentary for where other duplicate entries might need to
be made (amd64-xen, i386-xen, and i386-xen-pae).

Update sets lists for new compat_sysv module.

Update sets lists for new sysmon modules

Update sets lists for new swwdog module

Add missing entries for dtrace modules to set lists.

add dtrace_lockstat

i2c devices don't actually have a dependency on "iic" (the bus driver)
but on "i2cexec". Create an i2cexec module (i2c_exec.c) to mirror the
dependencies in files.i2c and switch device drivers to depend on "i2cexec"
module instead.

A kernel with a USB stack and no I2C controller / bus attachment would spit
out a bunch of "WARNING: module error: can't find builtin dependency `iic'"
messages at boot. This change solves that problem.

Per the wiki roadmap, rename the three dtrace modules to have
a "dtrace_" prefix.
amd64 build tested, other set list changes done the same way.

branches: 1.69.2;
add hythygtemp module to set lists

sort

branches: 1.67.2;
Re-sort, and update md.evbppc for new crypto modules

Add new modules for opencrypto

Add new crypto algorithm modules to sets list

Add new zlib module

Add entries for new ccd module

Update sets lists for new modules.

Do not remove luacore entries, mark them as obsolete instead.

renamed luacore to luasystm

ubsec is not a MI buildable module. disable it for now.

Make ubsec(4) loadable as kmod.

Build a module for usmsc(4).

linke pmf(9l) to the build

link core(9l) (docs pending) to the build

link the lua(4) module to the build

Add driver for ASIX AX88178a and AX88179 Ethernet interface.
Ported from OpenBSD.

Sort entries in strcmp order.

more npf sets lossage.

Add entries for "cylic" and "profile" modules which are part of DTrace.

Add NPF "rndblock" extension to randomly drop packets (using a random function
with a percentage or modulo operation). This is a demo module, although it can
be used for packet loss simulation. Example of a procedure in npf.conf:

procedure "somedrop" {
# Drop 1.9% of the traffic
rndblock: percentage 1.9
}

Implement dynamic NPF extensions interface. An extension consists of
dynamically loaded module (.so) supplementing npfctl(8) and a kernel
module. Move normalisation and logging functionality into their own
extensions. More improvements to come.

branches: 1.47.2;
The hdaudio and hdafg modules are not MI (they at least require PCI)

Build hdaudio and hdafg modules.

Add distrib entries for new uatp module.

Hello, riastradh!

add vcoda module

Actually create the if_axe module - driver was modularized a while ago.

Actually create the dbcool(4) module. Driver was modularized a while ago.

Create the module for sdtemp (driver itself was modularized some time ago)

P1003_1B_SEMAPHORE is no longer optional.

branches: 1.39.2;
Set list fix...

add chfs.kmod

Build and install new in-kernel iscsi initiator kernel module and associated
binaries (iscsid, iscsictl) if MKISCSI != no. Initiator can also be built
into a kernel by adding 'pseudo-device iscsi' in kernel configuration.

Add entries for "npf_alg_icmp" kernel module.

Add "npf" kernel module.