selftests: net: Correct couple of spelling mistakes

Changes :
- "excercise" is corrected to "exercise" in drivers/net/mlxsw/spectrum-2/tc_flower.sh
- "mutliple" is corrected to "multiple" in drivers/net/netdevsim/ethtool-fec.sh

Signed-off-by: Prabhav Kumar Vaish <pvkumar5749404@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240228120701.422264-1-pvkumar5749404@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: spectrum_acl_tcam: Fix stack corruption

When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.

One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.

In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.

Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.

Add a test case to make sure the machine does not crash when this
condition is hit.

[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b

Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: spectrum_acl_erp: Fix error flow of pool allocation failure

Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.

The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.

Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.

gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.

Fix this by changing erp_table->base_index only in case of a successful
allocation.

Add a test case for such a scenario. Without this fix it causes
segmentation fault:

$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null

[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
<TASK>
__mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
objagg_obj_root_destroy+0x18/0x80 [objagg]
objagg_obj_destroy+0x12c/0x130 [objagg]
mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
tc_setup_cb_destroy+0xc1/0x180
fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
__fl_delete+0x1ac/0x1c0 [cls_flower]
fl_destroy+0xc2/0x150 [cls_flower]
tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion

Fixes: f465261aa105 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests: forwarding: devlink_lib: Avoid double sourcing of lib.sh

Don't source lib.sh twice and make the script work with ifnames passed
on the command line.

Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: spectrum-2: Add massive delta rehash test

Do insertions and removal of filters during rehash in higher volumes.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: spectrum-2: Check migrate end trace

Add checking of newly added trace.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: spectrum-2: Add IPv6 variant of simple delta rehash test

Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints. Use IPv6 addresses.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: spectrum-2: Add simple delta rehash test

Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: spectrum-2: Add delta two masks one key test

Ensure that the bug is fixed and we no longer have C-TCAM spill for two
keys that differ only in delta.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: spectrum-2: Fix multiple_masks_test

With recent fix in C-TCAM spillage for delta masks, the test stops to be
falsely positive. So fix it not to use delta by adding src_ip bits to the
masks. Alongside with that, use C-TCAM spill trace to see when the
spillage actually happens.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: spectrum-2: Extend and move trace helpers

Allow to specify number of trace hits and move helpers
to the beginning of the file.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add Bloom delta test

The eRP table is active when there is more than a single rule
pattern. It may be that the patterns are close enough and use delta
mechanism. Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} where the rule delta bits must be
cleared.

Add a test that exercises Bloom filter with delta mechanism.
Configure rules within delta range and pass a packet which is
supposed to hit the correct rule.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add Bloom filter complex test

Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} and the computation also varies
according to the region key size.

Add a test that exercises the possible combinations by creating
multiple chains using different key sizes and then pass a frame that
is supposed to to produce a hit on all of the regions.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add Bloom filter simple test

Add a test that exercises Bloom filter code.
Activate eRP table in the region by adding multiple rule patterns which
with very high probability use different entries in the Bloom filter.
Then send packets in order to check lookup hits on all relevant rules.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: spectrum-2: Add simple delta test

Track the basic codepaths of delta handling, using objagg tracepoints.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: Adjust spectrum-2 ctcam_two_atcam_masks_test

In order for this to behave as required with delta bits, change the mask
for rule with handle 103.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: Adjust spectrum-2 two_mask_test

In order for this to behave as required with delta bits, change the mask
for rule with handle 103.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add TC flower test for Spectrum-2

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>