selftests: mlxsw: Add a test for locked port trap

Test that packets received via a locked bridge port whose {SMAC, VID}
does not appear in the bridge's FDB or appears with a different port,
trigger the "locked_port" packet trap.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests: mlxsw: Do not hard code trap group name

It can be derived dynamically from the trap's name, so drop it.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: pass pref and handle to devlink_trap_drop_* helpers

Currently the helpers assume pref 1 and handle 101. Make that explicit
and pass the values from callers.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: devlink: Make devlink_trap_cleanup() more generic

Add proto parameter in order to enable the use of devlink_trap_cleanup()
in tests that use IPv6 protocol.

Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: devlink: Export functions to devlink library

l2_drops_test() is used to check that drop traps are functioning as
intended. Currently it is only used in the layer 2 test, but it is also
useful for the layer 3 test introduced in the subsequent patch.

l2_drops_cleanup() is used to clean configurations and kill mausezahn
proccess.

Export the functions to the common devlink library to allow it to be
re-used by future tests.

Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum: Clear VLAN filters during port initialization

When a port is created, its VLAN filters are not cleared by the
firmware. This causes tagged packets to be later dropped by the ingress
STP filters, which default to DISCARD state.

The above did not matter much until commit b5ce611fd96e ("mlxsw:
spectrum: Add devlink-trap support") where we exposed the drop reason to
users.

Without this patch, the drop reason users will see is not consistent. If
a port is enslaved to a VLAN-aware bridge and a packet with an invalid
VLAN tries to ingress the bridge, it will be dropped due to ingress STP
filter. If the VLAN is later enabled and then disabled, the packet will
be dropped by the ingress VLAN filter despite the above being a
seemingly NOP operation.

Fix this by clearing all the VLAN filters during port initialization.
Adjust the test accordingly.

Fixes: b5ce611fd96e ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add test cases for devlink-trap L2 drops

Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>