ASoC: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Link: https://lore.kernel.org/r/20230425095716.331419-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org

ASoC: rt9120: Make dev PM runtime bind AsoC component PM

RT9120 uses PM runtime autosuspend to decrease the frequently on/off
spent time. This exists one case, when pcm is closed and dev PM is
waiting for autosuspend time expired to enter runtime suspend state.
At the mean time, system is going to enter suspend, dev PM runtime
suspend won't be called. It makes the rt9120 suspend consumption
current not as expected.

This patch can fix the rt9120 dev PM issue during runtime autosuspend
and system suspend by binding dev PM runtime and ASoC component PM.

Fixes: 80b949f332e3 ("ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1672301033-3675-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic

From the datasheet, the only way to meet the lowest power consumption is
to pull low the 'pwdnn' gpio. But if it is low, IC will keep in
reset state, all registers reset to default.

And the power consumption is listed below
1. amp off and 'pwdnn' high => idle state, PVDD = 1mA, DVDD = 7mA
2. amp off and 'pwdnn' low => shutdown state, PVDD < 20uA, DVDD < 15uA

It's the large difference for the consumption current

This fix is to use pm_runtime and regcache to handle 'pwdnn' gpio
control.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1652926418-8519-3-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Fix 3byte read, valule offset typo

For RG 3byte read, the value order is offset [0], [1], and [2].

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1652926418-8519-2-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Add endianness flag in snd_soc_component_driver

The endianness flag is used on the CODEC side to specify an
ambivalence to endian, typically because it is lost over the hardware
link. This device receives audio over an I2S DAI and as such should
have endianness applied.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220504170905.332415-24-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Correct the reg 0x09 size to one byte

Correct the reg 0x09 size to one byte.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1650608810-3829-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Add the compatibility with rt9120s

Use device id reg to be compatible with rt9120 and rt9120s.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1636515921-31694-4-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Fix clock auto sync issue when fs is the multiple of 48

If fs is divided by 48, to make audio clock sync rate correct, internal
sync function have be disabled.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1636515921-31694-3-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Update internal ocp level to the correct value

Update internal ocp level to correct value.

Even the wrong ocp setting can also make the sound output, but the power
cannot match the IC capability.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1636515921-31694-2-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Add rt9210 audio amplifier support

Add Richtek rt9120 audio amplifier support.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1634088519-995-3-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Drop rt9210 audio amplifier support

This drops the rt9210 support due to a race with a new version being
sent out for some incremental changes.

Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt9120: Add rt9210 audio amplifier support

Add Richtek rt9120 audio amplifier support.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
[Fix a Gain->Volume -- broonie]
Message-Id: <1633668612-25524-3-git-send-email-u0084500@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>