#
2db68ddb |
|
20-Dec-2023 |
Cristian Ciocaltea <cristian.ciocaltea@collabora.com> |
riscv: dts: starfive: beaglev-starlight: Setup phy reset gpio The BeagleV Starlight SBC uses a Microchip KSZ9031RNXCA PHY supporting RGMII-ID which doesn't require any particular setup, other than defining a reset gpio, as opposed to VisionFive V1 for which the RX internal delay had to be adjusted. Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
#
5076da2a |
|
17-Oct-2022 |
Cristian Ciocaltea <cristian.ciocaltea@collabora.com> |
riscv: dts: starfive: Add common DT for JH7100 based boards In preparation for adding initial device tree support for the StarFive VisionFive board, which is similar with BeagleV Starlight, move most of the content from jh7100-beaglev-starlight.dts to a new file, to be shared between the two boards. Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
#
ba99b756 |
|
30-Sep-2022 |
Jianlong Huang <jianlong.huang@starfivetech.com> |
pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100" Add the SoC name to make it more clear. Also the next generation StarFive SoCs will use "pinctrl-starfive" as the core of StarFive pinctrl driver. No functional change. Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com> Signed-off-by: Hal Feng <hal.feng@linux.starfivetech.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220930061404.5418-1-hal.feng@linux.starfivetech.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
#
a4367627 |
|
10-Oct-2021 |
Emil Renner Berthing <kernel@esmil.dk> |
RISC-V: Add BeagleV Starlight Beta device tree Add initial device tree for the BeagleV Starlight Beta board. About 300 of these boards were sent out as part of a now cancelled BeagleBoard.org project. I2C timing data is based on the device tree in the vendor u-boot port. Heartbeat LED added by Geert. Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Co-developed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
|