arm64: dts: renesas: ebisu: Document Ebisu-4D support

Document properly that Ebisu-support includes the Ebisu-4D variant, so
there won't be confusion what happened with support for this board.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231004152751.3917-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Factor out Ebisu board support

Move the common parts for the Renesas Ebisu board to ebisu.dtsi, to
avoid future duplication of board descriptions.

Change a reference in a comment from "r8a77990" to "R-Car E3(e)", to
prepare for the advent of "R-Car E3e".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/df275772dea0a4fa88d1bffa96ce048eaa7d5308.1628766192.git.geert+renesas@glider.be

arm64: dts: renesas: rcar-gen3: Add SoC model to comment headers

Make sure the R-Car Gen3 SoC model present is documented in the comment
header of each board DTS, on a single line. This makes it easier to
identify boards that are available with different SoC or SiP options.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/251569665d7d4f4ed4bbab7267ce2ddccdef33e5.1626261816.git.geert+renesas@glider.be

arm64: dts: renesas: r8a77990: ebisu: Add I2C EEPROM for PMIC

Add a device node for the I2C EEPROM which serves as external storage
for the PMIC setup, as a backup of the internal OTP configuration.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/32443cd203ce2787d9a719d06a473b9e9cd508c2.1625489160.git.geert+renesas@glider.be

arm64: dts: renesas: r8a77990: ebisu: Add SW4 support

Add support for SW4 via "gpio-keys" on the R-Car E3 Ebisu board.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Link: https://lore.kernel.org/r/162416649714.11444.12659951671817146236.sendpatchset@octo
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Add port@0 node for all CSI-2 nodes to dtsi

The port@0 is a mandatory port, add or move the declaration to the CSI-2
nodes top declared in dtsi files instead of depending on dts files
adding them when describing the external connection.

This fixes validation warnings for DTB outputs that do not connect all
CSI-2 receivers to transmitters and thus declaring all port@0 nodes in
dts files.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210421150221.3202955-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Add mmc aliases into board dts files

After the commit 7320915c8861 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in v4.14"), the order of /dev/mmcblkN
was not fixed in some SoCs which have multiple sdhi controllers.
So, we were hard to use an sdhi device as rootfs by using
the kernel parameter like "root=/dev/mmcblkNpM".

According to the discussion on a mainling list [1], we can add
mmc aliases to fix the issue. So, add such aliases into Renesas
arm64 board dts files. Notes that mmc0 is an eMMC channel if
available.

[1]
https://lore.kernel.org/linux-arm-kernel/CAPDyKFptyEQNJu8cqzMt2WRFZcwEdjDiytMBp96nkoZyprTgmA@mail.gmail.com/

Fixes: 7320915c8861 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1614596786-22326-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Group tuples in pin control properties

To improve human readability and enable automatic validation, the tuples
in "pinctrl-*" properties should be grouped using angle brackets.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210204130517.1647073-6-geert+renesas@glider.be

arm64: dts: renesas: Group tuples in playback and capture properties

To improve human readability and enable automatic validation, the tuples
in "playback" and "capture" properties in sound device nodes should be
grouped using angle brackets.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210204130517.1647073-5-geert+renesas@glider.be

arm64: dts: renesas: Disable SD functions for plain eMMC

Some SDHI instances are solely used for eMMC. Disable SD and SDIO
for faster initialization.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adam Ford <aford173@gmail.com> (beacon)
Link: https://lore.kernel.org/r/20210119133322.87289-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Drop superfluous pin configuration containers

As the pin configuration child nodes for EtherAVB on the Draak and Ebisu
boards contain only a single configuration, there is no need to wrap
them in additional grandchild containers. Hence remove the superfluous
level.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819123910.19606-1-geert+renesas@glider.be

arm64: dts: renesas: add full-pwr-cycle-in-suspend into eMMC nodes

Add full-pwr-cycle-in-suspend property to do a graceful shutdown of
the eMMC device in system suspend.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594382612-13664-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Make hdmi encoder nodes compliant with DT bindings

Small fixes to make these DTs compliant with the adi,adv7511w binding.

r8a77970-eagle.dts,
r8a77970-v3msk.dts,
r8a77980-condor.dts,
r8a77980-v3hsk.dts,
r8a77990-ebisu.dts:
Remove the adi,input-style and adi,input-justification properties.

r8a77995-draak.dts:
Reorder the I2C slave addresses of the hdmi-encoder@39 node and
remove the adi,input-style and adi,input-justification properties.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-2-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound

rcar_sound doesn't support clkout-lr-synchronous in upstream.
It was supported under out-of-tree rcar_sound.
upstream rcar_sound is supporting
- clkout-lr-synchronous
+ clkout-lr-asynchronous

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mubt3tux.wl-kuninori.morimoto.gx@renesas.com
Fixes: 56629fcba94c698d ("arm64: dts: renesas: ebisu: Enable Audio")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: Group tuples in regulator-gpio states properties

To improve human readability and enable automatic validation, the tuples
in the "states" properties of device nodes compatible with
"regulator-gpio" should be grouped, as reported by "make dtbs_check":

$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dt.yaml: regulator-vccq-sdhi0: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dt.yaml: regulator-vccq-sdhi0: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dt.yaml: regulator-vccq-sdhi3: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dt.yaml: regulator-vccq-sdhi3: states:0: [3300000, 1, 1800000, 0] is too long
...

Fix this by grouping the tuples using angle brackets.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-6-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>

arm64: dts: renesas: ebisu, draak: Limit EtherAVB to 100Mbps

* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).

* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.

Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.

Based on work by Kazuya Mizuguchi.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: r8a77990: ebisu: Sort nodes

Sort nodes.

If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically

This should not have any run-time effect.

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Sort sound child nodes]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: ebisu: Remove renesas, no-ether-link property

It is incorrect to specify the no-ether-link property for the AVB device on
the Ebisu board. This is because the property should only be used when a
board does not provide a proper AVB_LINK signal. However, the Ebisu board
does provide this signal.

As per 87c059e9c39d ("arm64: dts: renesas: salvator-x: Remove renesas,
no-ether-link property") this fixes a bug:

Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.

As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.

Choosing to keep or remove the "renesas,no-ether-link" option will have
impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since the
RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).

In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.

Fixes: 8441ef643d7d ("arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: Use ip=on for bootargs

Convert bootargs from ip=dhcp to ip=on

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: Update Ebisu and Draak bootargs

Update Ebisu and Draak bootargs to match other boards

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ebisu: Add PMIC DDR0 Backup Power config

On Ebisu the DDR0 power rail needs to be kept powered when backup mode is
enabled. Reflect this in the "rohm,ddr-backup-power" property for the
BD9571MWV PMIC node.

The accessory power switch (SW23) is a toggle switch, hence specify
"rohm,rstbmode-level".

Based on advice from Geert Uytterhoeven.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: r8a77990-ebisu: Add BD9571 PMIC

This patch adds the regulator definition required for operation of
S2RAM.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: ebisu: Enable VIN5

Both VIN4 and VIN5 are connected to CSI40 and can be configured at
runtime to use the single video source connected to CSI40. Enable VIN5
to allow it to be used in this fashion.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Niklas: rewrite commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ebisu: Fix adv7482 hexadecimal register address

The register address used for the reg property of the adv7482 node in
other Renesas device trees are decimal not hex, change this for Ebisu to
align it with the others.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Niklas: rewrite commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Enable LVDS1 encoder

The LVDS1 encoder must supply a pixel clock to the DU for the DPAD
output when the LVDS0 encoder is used. Enable it despite its output not
being connected.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Fix SPDX license identifier style

According to Documentation/process/license-rules.rst, SPDX license
identifiers in DTS files should use C++ style comments.

Fixes: f37a7767f6c4ec66 ("arm64: dts: renesas: Add Renesas R8A77990 SoC support")
Fixes: 77049191b24b4586 ("arm64: dts: renesas: Add Renesas Ebisu board support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Add GPIO expander

Describe the ON Semiconductor PCA9654 I/O expander on the first I2C
bus, which provides 8 extra GPIOs.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Enable HS400 of SDHI3

Enable HS400 of SDHI3 using the corresponding DT property.
No further changes are required.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

arm64: dts: renesas: r8a77990: ebisu: Fix backlight regulator numbering

There are two regulator1 nodes in the Ebisu DTS right now, one 3.3V for
the eMMC and one 12V for the backlight. This causes one to be overwritten
by the other, ultimatelly resulting in inoperable eMMC, which depends on
the former. Fix this by renumbering the backlight regulator to regulator2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 9d16c4a10e07 ("arm64: dts: renesas: r8a77990: ebisu: Add backlight")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990-ebisu: use simple-audio-card

Current Ebisu board is using simple-scu-audio-card
which is used for Sampling Rate Convert, or MIXer, etc.
But, Ebisu is not using such feature.
Then, simple-audio-card is very enough.
This patch fixup it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Fix EthernetAVB phy mode to rgmii

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode doesn't support
on R-Car E3. This patch fixes EthernetAVB phy mode to rgmii.

This is achieved by simply dropping the phy-mode property from
r8a77990-ebisu.dts as the default property for this for r8a77990,
as set in r8a77990.dtsi, is "rgmii".

Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>

arm64: dts: renesas: r8a77990: ebisu: Add backlight

Add the backlight device for the LVDS1 output, in preparation for panel
support.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Add and enable CAN,FD device nodes

This patch adds CAN0,1 and CANFD device nodes for the r8a77990 SoC
and enables CANFD connected to CN10 on the E3 Ebisu board using the
R8A77990 SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Add and enable PCIe device node

This patch adds PCI express channel 0 device node to the R8A77990 SoC
and enables PCIEC0 PCI express controller on the Ebisu board.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ebisu: Add and enable SDHI device nodes

This patch adds SDHI{0,1,3} device nodes for the r8a77990 SoC
and enables SD card slot connected to SDHI0, micro SD card slot
connected to SDHI1 and eMMC connected to SDHI3 on the Ebisu board
using the R8A77990 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ebisu: Add serial console pins

This patch adds pin control for SCIF2 on R8A77990 E3 Ebisu.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ebisu: Enable Audio

This patch enables Audio for the Ebisu board on R8A77990 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7799{0|5}: add/enable USB2.0 peripheral

This patch adds/enables USB2.0 peripheral for R-Car [DE]3 boards.

R-Car E3 Ebisu board connects the ID pin to the SoC, so this adds
a group "usb0_id" into usb0_pins node. Also, to use SW15 pin 3 side,
this patch adds vbus0_usb2 node on r8a77990-ebisu.dts.

R-Car D3 Draak board doesn't connect the ID pin, so this adds
"renesas,no-otg-pins" property into usb2_phy0 node.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: add/enable USB3.0 peripheral device node

This patch adds/enables USB3.0 peripheral device node for r8a77990
ebisu board.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Enable VGA and HDMI outputs

Add the LVDS decoder, HDMI encoder, VGA encoder and HDMI and VGA
connectors, and wire up the display-related nodes with clocks, pinmux
and regulators.

The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Ebisu
board, hook them up in DT.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ebisu: Add HDMI and CVBS input

Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.

Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Enable PWM for Ebisu board

This patch adds PWM device nodes and enables PWM3 and PWM5 for
R-Car E3 Ebisu board. These devices are used for backlight control.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Enable USB3.0 host for Ebisu board

This patch adds and USB3.0 host device node and enable it for
R-Car E3 Ebisu board.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Enable USB2.0 Host for Ebisu board

This patch adds USB2.0 PHY and Host(EHCI/OHCI) nodes and
enables them for R-Car E3 Ebisu board.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Enable watchdog timer

Add a device node for the Watchdog Timer (WDT) controller on the
R8A77990 SoC, and enable the watchdog on the Ebisu board.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed 2 commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB

This patch enables EthernetAVB for r8a77990 Ebisu board.

Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: Add Renesas Ebisu board support

Basic support for the Renesas Ebisu board based on R-Car E3:
- Memory,
- Main crystal,
- Serial console,

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>