arm64: dts: freescale: Fix pca954x i2c-mux node names

"make dtbs_check":

arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: $nodename:0: 'pca9547@77' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@4' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...

Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa-rdb: fix errata E-00013

Specify a channel zero in idle state to avoid enterring tri-stated state
for PCA9547.

Some information about E-00013:
- Description: I2C1 and I2C3 buses are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus will float.
This makes the I2C bus and its associated downstream devices
inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1 and resistors
R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
driver(PCA954x always on enable status, specify a channel zero in dts to
fix the errata E-00013).

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: align SPI NOR node name with dtschema

The node names should be generic and SPI NOR dtschema expects "flash".

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa-rdb: add interrupt line for RTC node

Add interrupt line for RTC node on ls208xa-rdb

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa: Update qspi node properties for LS2088ARDB

LS2088ADB has one spansion flash s25fs512s of size 64M.

Add qspi dts entry for the board using compatibles as "jedec,spi-nor" to
probe flash successfully. Also, align properties with other board dts
properties.

Use dt-bindings constants in interrupts instead of using numbers.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: Update to use SPDX identifiers

Replace license text with corresponding SPDX identifiers and update the
format of existing SPDX identifiers to follow the new guideline
Documentation/process/license-rules.rst.

Note that some of the files mentioned X11 license previously but the
license text actually matches MIT license.

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa-rdb: Pass unit name to SPI flash node

Pass unit name to SPI flash node to match its 'reg' value and
also avoid the following DTC warnings:

arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dtb: Warning (unit_address_vs_reg): /soc/dspi@2100000/n25q512a: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dtb: Warning (unit_address_vs_reg): /soc/dspi@2100000/n25q512a: node has a reg or ranges property, but no unit name

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa: add power monitor chip node

Ina220 chip was used on ls208xardb platform to monitor power
comsumption. So add ina220 chip node in dts to enable power
consumption monitor feature.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa: disable SD UHS-I modes by default on RDB

Currently SD UHS-I modes were enabled by default on LS208xARDB boards,
but the new LS2088ARDB RevF board didn't support them any more since SDHC
circuit had been reworked. This patch is to disable SD UHS-I modes by default
in case of any issue on LS2088ARDB RevF

Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa: support SD UHS-I on RDB and eMMC HS200 on QDS

This patch is to enable SD UHS-I mode on LS208xRDB and eMMC HS200
mode on LS208xQDS in dts. Also, the eSDHC peripheral clock must be
used instead of platform clock to support these modes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: update the copyright claims

Update the copyright claims to comply with company policy.

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: ls2080a: Split devicetree for code resuability

LS2088A and LS2080A are similar SoCs with a few differences like
ARM cores etc.

Reorganize the LS2080A device tree to move the common nodes to:
- fsl-ls208xa.dtsi
- fsl-ls208xa-rdb.dtsi
- fsl-ls208xa-qds.dtsi

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>