arm64: dts: juno: Fix UART frequency

Older versions of the Juno *SoC* TRM [1] recommended that the UART clock
source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more
correct value of 7.3728 MHz. Somehow the wrong value managed to end up in
our DT.

Doing a prime factorisation, a modulo divide by 115200 and trying
to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest
that the old value was actually a typo. The actual UART clock is driven
by a PLL, configured via a parameter in some board.txt file in the
firmware, which reads 7.37 MHz (sic!).

Fix this to correct the baud rate divisor calculation on the Juno board.

[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0515b.b/DDI0515B_b_juno_arm_development_platform_soc_trm.pdf
[2] http://infocenter.arm.com/help/topic/com.arm.doc.100113_0000_07_en/arm_versatile_express_juno_development_platform_(v2m_juno)_technical_reference_manual_100113_0000_07_en.pdf

Fixes: 71f867ec130e ("arm64: Add Juno board device tree.")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

arm64: dts: juno: remove dtsi nesting inside tree structure

Currently juno-clock.dtsi and juno-base.dtsi are nested badly inside
the device tree structure. It's generally good practice to ensure that
individual dtsi stand by themselves at the top of the file.

This patch removes the nesting of the above mentioned dtsi files and
makes them independent.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

arm64: Juno: Fix the GIC node address label and the frequency of FAXI clock.

During the review of the Juno DT files I've noticed that the GIC
node label had two digits swapped leading to a different address
being shown in the /sys/devices fs.

Sudeep also pointed that public revisions of the Juno documentation
list a different frequency for the FAXI system than what the one
I've been using when creating the DT file. Verified with the firmware
people to be the correct value in the shipped systems.

Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>

arm64: juno: Fix misleading name of UART reference clock

The UART reference clock speed is 7273.8 kHz, not 72738 kHz.

Dots aren't usually used in node names even though ePAPR permits
them. However, this can easily be avoided by expressing the
frequency in Hz, not kHz.

This patch changes the name to refclk7273800hz, reflecting the
actual clock speed.

Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

arm64: Add Juno board device tree.

This adds support for ARM's Juno development board (rev 0).
It enables most of the board peripherals: UART, I2C, USB, MMC and
100Mb ethernet. There is no support at the moment for clock setting
and HDLCD driver which depends on it.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>