arm64: dts: allwinner: h700: Add RG35XX-H DTS

The RG35XX-H adds thumbsticks, a stereo speaker, and a second USB port to
the RG35XX-Plus, and has a horizontal form factor.

Enabled in this DTS:
- Thumbsticks
- Second USB port

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240427110225.727472-8-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h700: Add RG35XX-Plus DTS

The RG35XX-Plus adds a RTL8221CS SDIO Wifi/BT chip to the RG35XX (2024).

Enabled in this DTS:
- WiFi
- Bluetooth
- Supporting power sequence and GPIOs

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240427110225.727472-7-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h700: Add RG35XX 2024 DTS

The base model RG35XX (2024) is a handheld gaming device based on an
Allwinner H700 chip.

The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
GPU) which exposes RGB LCD and NMI pins.

Device features:
- Allwinner H700 @ 1.5GHz
- 1GB LPDDR4 DRAM
- X-Powers AXP717 PMIC
- 3.5" 640x480 RGB LCD
- Two microSD slots
- Mini-HDMI out
- GPIO keypad
- 3.5mm headphone jack
- USB-C charging port

Enabled in this DTS:
- AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
controller
- Power LED (charge LED on device controlled directly by PMIC)
- Serial UART (accessible from headers on the board)
- First SD slot (SD2 appears to have a GPIO-switched regulator for 1.8v
low-voltage signalling, this is not yet modeled. Enablement with a
switched regulator will be confirmed and posted in a follow-up patch).

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240427110225.727472-6-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: Add Tanix TX1 support

The Tanix TX1 is a tiny TV box with the Allwinner H313 SoC. The box
features no Ethernet or an SD card slot, which makes booting from it
somewhat interesting: Pressing the hidden FEL button and using a USB-A
to USB-A cable to upload code from a host PC is one way to run mainline.
The box features:
- Allwinner H313 SoC (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- SCI S9082H WiFi chip
- HDMI port
- one USB 2.0 port
- 3.5mm AV port
- barrel plug 5V DC input via barrel plug

The devicetree covers most peripherals.
The eMMC did not work properly in HS200 speed mode, so this mode property
is omitted. HS-DDR seems to work fine.
The blue LED is connected to the same GPIO pin as the red LED, just
using the opposite polarity. Apparently there is no way of describing
this in DT, so the red LED is omitted.
Next to the FEL button is a hidden button, that can be pushed by using
something like a paperclip, through the ventilation vents of the case.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240418104942.1556914-3-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h616: Add Sipeed Longan SoM 3H and Pi 3H board support

The Sipeed Longan SoM 3H is a system on module based on the Allwinner
H618 SoC. The SoM features:

- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2/4 GiB LPDDR4 DRAM SoMs
- AXP313a PMIC
- eMMC

The Sipeed Longan PI 3H is a development board based on the above SoM.
The board features:
- Longan SoM 3H
- Raspberry-Pi-1 compatible GPIO header
- 2 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- 1Gbps Ethernet port (via RTL8211 PHY)
- HDMI port
- WiFi/BT chip

Add the devicetree file describing the currently supported features,
namely PMIC, LEDs, UART, SD card, eMMC, USB and Ethernet.

Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240211081739.395-3-jszhang@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: Add Jide Remix Mini PC support

The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
- RTL8723BS WiFi & Bluetooth chip
- HDMI port
- two USB 2.0 ports
- 3.5mm AV port
- microSD card slot

The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.
The eMMC did not work with the MMC DDR speed mode, so this mode property
is omitted.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240209114018.3580370-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h616: Add Orange Pi Zero 2W to Makefile

Orange Pi Zero 2W dts file is not included in Makefile. Fix this.

Fixes: c505ee1eae18 ("arm64: dts: allwinner: h616: add Orange Pi Zero 2W support")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240222211326.114955-1-jernej.skrabec@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h618: add Transpeed 8K618-T TV box

This is a Chinese TV box, probably very similar if not identical to
various other cheap TV boxes with the same specs:
- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
- 2 or 4GiB DDR3L DRAM
- 32, 64, or 128 GiB eMMC flash
- AXP313a PMIC
- 100 Mbit/s Ethernet (using yet unsupported internal PHY)
- HDMI port
- 2 * USB 2.0 ports
- microSD card slot
- 3.5mm A/V port
- 7-segment display
- 5V barrel plug power supply

The PCB provides holes for soldering a UART header or cable, this is
connected to the debug UART0. UART1 is used for the Bluetooth chip,
although this isn't working yet.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231214015312.17363-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h616: Add BigTreeTech Pi support

The BigTreeTech Pi is an H616 based board based on CB1.
Just in Rpi format board.

It features the same internals as BTT CB1 but adds:
- Fan port
- IR receiver
- ADXL345 Accelerometer connector via SPI
- 24V DC power supply via terminal plugs
- USB to CAN module connector (External Module)

List of currently working things is same as BTT CB1 but also:
- IR receiver
- ADXL345 connector

Signed-off-by: Martin Botka <martin@biqu3d.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230912-b4-cb1-v6-4-bb11238f3a9c@somainline.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h616: Add BigTreeTech CB1 SoM & boards support

CB1 is Compute Module style board that plugs into Rpi board style adapter or
Manta 3D printer boards (M4P/M8P).

The SoM features:
- H616 SoC
- 1GiB of RAM
- AXP313A PMIC
- RTL8189FTV WiFi

Boards feature:
- 4x USB via USB2 hub (usb1 on SoM).
- SDcard slot for loading images.
- Ethernet port wired to the internal PHY. (100M)
- 2x HDMI 2.0. (Only 1 usable on CB1)
- Power and Status LEDs. (Only Status LED usable on CB1)
- 40 pin GPIO header

Currently working:
- Booting
- USB
- UART
- MMC
- Status LED
- WiFi (RTL8189FS via out of tree driver)

I didnt want to duplicate things so the manta DTS can also be used on BTT pi4b adapter.
CB1 SoM has its own DTSI file in case other boards shows up that accept this SoM.

Signed-off-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230912-b4-cb1-v6-3-bb11238f3a9c@somainline.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The board itself is a
slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features,
namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at
the moment, though the basic functionality works.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230804170856.1237202-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arm64: dts: allwinner: h616: Add X96 Mate TV box support

The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-8-andre.przywara@arm.com

arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-7-andre.przywara@arm.com

arm64: dts: allwinner: h6: Add Tanix TX6 mini dts

Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.

Basic specs:
- H6 SoC
- 2 GiB DDR3 RAM
- HDMI
- SPDIF
- 2x USB
- analogue audio
- CVBS
- SD card
- IR remote
- LED display
- fast ethernet
- XR819 wifi
- 16 GiB eMMC

Currently supported features doesn't differ that much from Tanix TX6,
but that will change soon.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h5: Add NanoPi R1S H5 support

The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:

- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn

arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab

PineTabs since Early Adopter batch will use a new LCD panel.

Add device tree for PineTab with the new panel.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201224024001.19248-2-icenowy@aosc.io

arm64: allwinner: A100: add support for Allwinner Perf1 board

A100 perf1 is an Allwinner A100-based SBC, with the following features:

- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- on-board Nand flash
- ···

Adds initial support for it, including UART and PMU.

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/30f4a3fc6ac84d05094e2c3b89d1dddc8ff6b7fc.1595572867.git.frank@allwinnertech.com

arm64: dts: allwinner: Add support for PinePhone revision 1.2

Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.

Interrupt to the magnetometer is routed correctly, in this revision.

The bulk of the changes are in how modem and the USB-C HDMI bridge
chip is powered and where the signals from the modem are connected.

Also backlight intensity seemingly behaves differently, than on the
1.1 and 1.0 boards, and the PWM duty cycle where backlight starts
to work is 10% (as tested on 2 1.2 PinePhones I have access to).

Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20200703194842.111845-3-megous@megous.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: Add initial support for Pine64 PinePhone

At the moment PinePhone comes in two slightly incompatible variants:

- 1.0: Early Developer Batch
- 1.1: Braveheart Batch

There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.

The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.

This is a basic DT that includes only features that are already
supported by mainline drivers.

Co-developed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: a64: add support for PineTab

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board

The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed

Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.

eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s

Changes:

v3: Separate dts for eMMC variants

v2: Fix descriptions for VCC and VCCQ

Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: Introduce Tanix TX6 board

Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: Add Orange Pi 3 DTS

Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:

- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe

Add basic support for the board.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: Introduce Beelink GS1 board

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support

Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: h6: Add OrangePi Lite2 initial support

OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: new board - Emlid Neutis N5

Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis n5 dtsi file for SoM needs
- add neutis devboard dts file
- add neutis devboard target to dtb makefile

Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees

Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.

This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5

The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.

Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: h6: Add OrangePi One Plus initial support

OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: a64: Add Pine64-LTS device tree file

The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: add support for Pinebook

Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:

USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.

Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.

Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.

Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.

Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.

This commit adds basical support for it.

[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: a64: Add Amarula A64-Relic initial support

Amarula A64-Relic is Allwinner A64 based IoT device, which support
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 1GB DDR3 RAM
- 8GB eMMC
- AP6330 Wifi/BLE
- MIPI-DSI
- CSI: OV5640 sensor
- USB OTG
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.

The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.

This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.

Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: Sort dtb entries in Makefile

The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.

Move them so the list is properly sorted.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus

The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG

This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: a64: Add support for TERES-I laptop

The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.

Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: h6: add support for Pine H64 board

Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port

Adds initial support for it, including the UART on the Expansion pin
header.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib

If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.

Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.

One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.

Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.

As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>

kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile

We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.

Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: allwinner: h5: add NanoPi NEO Plus2 DT support

Add initial DT for NanoPi NEO Plus2 by FriendlyARM
- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
- 1 GB DDR3 RAM
- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
- micro SD card slot
- Gigabit Ethernet (external RTL8211E-VB-CG chip)
- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
- 2x USB 2.0 host ports & 2x USB via headers

Signed-off-by: Antony Antony <antony@phenome.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: a64: Add A64-OLinuXino initial support

OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.

OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: allwinner: a64: Add initial NanoPi A64 support

NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.

Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: allwinner: h5: Add initial Orangepi Zero Plus 2 support

Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: a64: Add initial Orangepi Win/WinPlus support

Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.

A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: a64: add device tree for SoPine with baseboard

Pine64 have made an official baseboard when SoPine SoM is out.

The official baseboard is like the original Pine64 -- but with SD card
slot replaced with Pine64's eMMC module slot.

Add a device tree for SoPine with the baseboard.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: h5: add support for NanoPi NEO2 board

NanoPi NEO2 is a board with the same size factor with the original
NanoPi NEO by FriendlyELEC.

It has a H5 instead of H3 on NanoPi NEO, and the ethernet is upgraded to
1Gbps (with external RTL8211E PHY).

Add support for this board.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: h5: add support for Orange Pi Prime board

Orange Pi Prime is a new Allwinner H5-based SBC by Xunlong.

It's like a Orange Pi Plus 2E with H3 replaced with H5, eMMC replaced
with onboard SPI NOR Flash and wireless card changed to Realtek
RTL8723BS (with Bluetooth functionality).

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: h5: add support for the Orange Pi PC 2 board

The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.

Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.

Reviewed-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm64: allwinner: add BananaPi-M64 support

The Banana Pi M64 board is a typical single board computer based on the
Allwinner A64 SoC. Aside from the usual peripherals it features eMMC
storage, which is connected to the 8-bit capable SDHC2 controller.
Also it has a soldered WiFi/Bluetooth chip, so we enable UART1 and SDHC1
as those two interfaces are connected to it.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: add Pine64 support

The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Maxime: Removed the common DTSI and include directly the pine64 DTS]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>