wifi: cfg80211: Schedule regulatory check on BSS STA channel change

Due to different relaxation policies it may be needed to re-check
channels after a BSS station interface is disconnected or performed a
channel switch.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.1f2f8475bcf1.I1879d259d8d756159c8060f61f4bce172e6d323e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: cfg80211: reg: fix various kernel-doc issues

Clean up the kernel-doc comments in reg.h.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230827135854.36d7b52da0f5.I85fbfb3095613f4a0512493cbbdda881dc31be2c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: avoid holding the RTNL when calling the driver

Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.

Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).

Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.

Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

net: Fix various misspellings of "connect"

Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211: fix scan when operating on DFS channels in ETSI domains

In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.

Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.

Enable scan in mac80211 in these cases.

Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: restore regulatory without calling userspace

Jouni reports that in some cases it is possible that getting
disconnected (or stopping AP, after previous patches) results
in further operations hitting the window within the regulatory
core restoring the regdomain to the defaults. The reason for
this is that we have to call out to CRDA or otherwise do some
asynchronous work, and thus can't do the restore atomically.

However, we've previously seen all the data we need to do the
restore, so we can hang on to that data and use it later for
the restore. This makes the whole thing happen within a single
locked section and thus atomic.

However, we can't *always* do this - there are unfortunately
cases where the restore needs to re-request, because this is
also used (abused?) as an error recovery process, so make the
new behaviour optional and only use it when doing a regular
restore as described above.

Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: implement regdb signature checking

Currently CRDA implements the signature checking, and the previous
commits added the ability to load the whole regulatory database
into the kernel.

However, we really can't lose the signature checking, so implement
it in the kernel by loading a detached signature (regulatory.db.p7s)
and check it against built-in keys.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: support reloading regulatory database

If the regulatory database is loaded, and then updated, it may
be necessary to reload it. Add an nl80211 command to do this.

Note that this just reloads the database, it doesn't re-apply
the rules from it immediately.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Share Channel DFS state across wiphys of same DFS domain

Sharing DFS channel state across multiple wiphys (radios) could
be useful with multiple radios on the system. When one radio
completes CAC and markes the channel available another radio
can use this information and start beaconing without really doing
CAC.

Whenever there is a state change in dfs channel associated to
a particular wiphy the the same state change is propagated to
other wiphys having the same DFS reg domain configuration.
Also when a new wiphy is created the dfs channel state of
other existing wiphys of same DFS domain is copied.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Make pre-CAC results valid only for ETSI domain

DFS requirement for ETSI domain (section 4.7.1.4 in
ETSI EN 301 893 V1.8.1) is the only one which explicitly
states that once DFS channel is marked as available afer
the CAC, this channel will remain in available state even
moving to a different operating channel. But the same is
not explicitly stated in FCC DFS requirement. Also, Pre-CAC
requriements are not explicitly mentioned in FCC requirement.
Current implementation in keeping DFS channel in available
state is same as described in ETSI domain.

For non-ETSI DFS domain, this patch gives a grace period of 2 seconds
since the completion of successful CAC before moving the channel's
DFS state to 'usable' from 'available' state. The same grace period
is checked against the channel's dfs_state_entered timestamp while
deciding if a DFS channel is available for operation. There is a new
radar event, NL80211_RADAR_PRE_CAC_EXPIRED, reported when DFS channel
is moved from available to usable state after the grace period. Also
make sure the DFS channel state is reset to usable once the beaconing
operation on that channel is brought down (like stop_ap, leave_ibss
and leave_mesh) in non-ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: remove enum ieee80211_band

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Stop calling crda if it is not responsive

Patch eeca9fce1d71a4955855ceb0c3b13c1eb9db27c1 (cfg80211: Schedule
timeout for all CRDA call) introduced a regression, where in case
that crda is not installed (or not configured properly etc.), the
regulatory core will needlessly continue to call it, polluting the
log with the following log:

"cfg80211: Calling CRDA to update world regulatory domain"

Fix this by limiting the number of continuous CRDA request failures.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Add API to change the indoor regulatory setting

Previously, the indoor setting configuration assumed that as
long as a station interface is connected, the indoor environment
setting does not change. However, this assumption is problematic
as:

- It is possible that a station interface is connected to a mobile
AP, e.g., softAP or a P2P GO, where it is possible that both the
station and the mobile AP move out of the indoor environment making
the indoor setting invalid. In such a case, user space has no way to
invalidate the setting.
- A station interface disconnection does not necessarily imply that
the device is no longer operating in an indoor environment, e.g.,
it is possible that the station interface is roaming but is still
stays indoor.

To handle the above, extend the indoor configuration API to allow
user space to indicate a change of indoor settings, and allow it to
indicate weather it controls the indoor setting, such that:

1. If the user space process explicitly indicates that it is going
to control the indoor setting, do not clear the indoor setting
internally, unless the socket is released. The user space process
should use the NL80211_ATTR_SOCKET_OWNER attribute in the command
to state that it is going to control the indoor setting.
2. Reset the indoor setting when restoring the regulatory settings in
case it is not owned by a user space process.

Based on the above, a user space tool that continuously monitors the
indoor settings, i.e., tracking power setting, location etc., can
indicate environment changes to the regulatory core.

It should be noted that currently user space is the only provided mechanism
used to hint to the regulatory core over the indoor/outdoor environment --
while the country IEs do have an environment setting this has been completely
ignored by the regulatory core by design for a while now since country IEs
typically can contain bogus data.

Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: ArikX Nemtsov <arik@wizery.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: allow usermode to query wiphy specific regdom

If a wiphy-idx is specified, the kernel will return the wiphy specific
regdomain, if such exists. Otherwise return the global regdom.

When no wiphy-idx is specified, return the global regdomain as well as
all wiphy-specific regulatory domains in the system, via a new nested
list of attributes.

Add a new attribute for each wiphy-specific regdomain, for usermode to
identify it as such.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Enable GO operation on indoor channels

Allow GO operation on a channel marked with IEEE80211_CHAN_INDOOR_ONLY
iff there is a user hint indicating that the platform is operating in
an indoor environment, i.e., the platform is a printer or media center
device.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Add an option to hint indoor operation

Add the option to hint the wireless core that it is operating in an indoor
environment.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Enable GO operation on additional channels

Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.

Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.

It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: regulatory: simplify uevent sending

There's no need for the struct device_type with the uevent function
etc., just fill the country alpha2 when sending the event.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: regulatory introduce maximum bandwidth calculation

In case we will get regulatory request with rule
where max_bandwidth_khz is set to 0 handle this
case as a special one.

If max_bandwidth_khz == 0 we should calculate maximum
available bandwidth base on all frequency contiguous rules.
In case we need auto calculation we just have to set:

country PL: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ AUTO), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS

This mean we will calculate maximum bw for rules where
AUTO (N/A) were set, 160MHz (5330 - 5170) in example above.
So we will get:
(5170 - 5250 @ 160), (N/A, 20)
(5250 - 5330 @ 160), (N/A, 20), DFS

In other case:
country FR: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS

We will get 80MHz (5250 - 5170):
(5170 - 5250 @ 80), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS

Base on this calculations we will set correct channel
bandwidth flags (eg. IEEE80211_CHAN_NO_80MHZ).

We don't need any changes in CRDA or internal regulatory.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[extend nl80211 description a bit, fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: add reg_get_dfs_region()

This can be used outside of the regulatory context for any checks
on the DFS region. The central cfg80211 dfs_region is always used
and if it does not match with the wiphy a debug print is issued.

Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: use enum nl80211_dfs_regions for dfs_region everywhere

u8 was used in some other places, just stick to the enum,
this forces us to express the values that are expected.

Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: check regulatory request alpha2 early

Currently nl80211 allows userspace to send the kernel
a bogus regulatory domain with at most 32 rules set
and it won't reject it until after its allocated
memory. Let's be smart about it and take advantage
that the last_request is now available under RTNL
and check if the alpha2 matches an expected request
and reject any bogus userspace requests prior to
hitting the memory allocator.

Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: rename regulatory_hint_11d() to regulatory_hint_country_ie()

It is incorrect to refer to this as 11d as 802.11d was just a
proposed amendment, 802.11d was merged to the standard so
use proper terminology.

Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

regulatory: use RCU to protect global and wiphy regdomains

To simplify the locking and not require cfg80211_mutex
(which nl80211 uses to access the global regdomain) and
also to make it possible for drivers to access their
wiphy->regd safely, use RCU to protect these pointers.

Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

regulatory: fix reg_is_valid_request handling

There's a bug with the world regulatory domain, it
can be updated any time which is different from all
other regdomains that can only be updated once after
a request for them. Fix this by adding a check for
"processed" to the reg_is_valid_request() function
and clear that when doing a request.

While looking at this I also found another locking
bug, last_request is protected by the reg_mutex not
the cfg80211_mutex so the code in nl80211 is racy.
Remove that code as it only tries to prevent an
allocation in an error case, which isn't necessary.
Then the function can also become static and locking
in nl80211 can have a smaller scope.

Also change __set_regdom() to do the checks earlier
and not different for world/other regdomains.

Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

regulatory: code cleanup

Clean up various things like indentation, extra
parentheses, too many/few line breaks, etc.

Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: fix BSS struct IE access races

When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.

Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: make regulatory_update() static

Now that we have wiphy_regulatory_register() we can
tuck away the core's regulatory_update() call there
and make it static.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: rename reg_device_remove() to wiphy_regulatory_deregister()

This makes it clearer what we're doing. This now makes a bit
more sense given that regardless of the wiphy if the cell
base station hint feature is supported we will be modifying the
way the regulatory core behaves.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: add cellular base station regulatory hint support

Cellular base stations can provide hints to cfg80211 about
where they think we are. This can be done for example on
a cell phone. To enable these hints we simply allow them
through as user regulatory hints but we allow userspace
to clasify the hint as either coming directly from the
user or coming from a cellular base station. This option
is only available when you enable
CONFIG_CFG80211_CERTIFICATION_ONUS.

The base station hints themselves will not be processed
by the core unless at least one device on the system
supports this feature.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: relicense reg.c reg.h and genregdb.awk to ISC

Following the tradition we have had with ath5k, ath9k, CRDA,
wireless-regdb I'd like to license this code under the permissive ISC
license for the code sharing purposes with other OSes, it'd sure be nice
to help the landscape in this area. Although I am %82.89 owner of the
regulatory code I have asked every contributor to the regulatory code
and have receieved positive Acked-bys from everyone except two deceased
entities:

o Frans Pop RIP 2010 [0]
- Frans Pop <elendil@planet.nl>
- Frans Pop <fjp@debian.org>
o Nokia RIP February, 11, 2011 [1], [2]
- ext-yuri.ershov@nokia.com
- kalle.valo@nokia.com

Frans Pop's contribution was a simple patch 55f98938, titled,
"wireless: remove trailing space in messages" which just add a \n
to some printk lines. I'm going to treat these additions as
uncopyrightable.

As for the contributions made by employees on behalf of Nokia
my contact point was Petri Karhula <petri.karhula@nokia.com> but
after one month he noted he had not been able to get traction from the
legal department on this request, as such it I proceeded by replacing
their contributions in previous patches.

The end goal is to help a clean rewrite that starts in userspace
that is shared under ISC license which currently is taking place with
the regulatory simulator [3].

[0] http://lists.debian.org/debian-devel/2011/12/msg00263.html
[1] http://press.nokia.com/2011/02/11/nokia-outlines-new-strategy-introduces-new-leadership-operational-structure/
[2] http://NokiaPlanB.com
[3] git://github.com/mcgrof/regsim.git

Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mihai Moldovan <ionic@ionic.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tony Vroon <tony@linx.net>
Acked-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Pat Erley <pat-lkml@erley.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Joe Perches <joe@perches.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: John Gordon <john@devicescape.com>
Acked-by: Simon Barber <protocolmagic@gmail.com>
Acked-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Jiri Benc <jbenc@upir.cz>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Scott James Remnant <keybuk@google.com>
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: process regulatory DFS region for countries

The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: hold reg_mutex when updating regulatory

The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.

Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.

Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/wireless: add COUNTRY to to regulatory device uevent

Regulatory devices issue change uevents to inform userspace of a need
to call the crda tool; however these can often be sent before udevd is
running, and were not previously included in the results of
udevadm trigger (which requests a new change event using the /uevent
attribute of the sysfs object).

Add a uevent function to the device type which includes the COUNTRY
information from the last request if it has yet to be processed, the
case of multiple requests is already handled in the code by checking
whether an unprocessed one is queued in the same manner and refusing
to queue a new one.

The existing udev rule continues to work as before.

Signed-off-by: Scott James Remnant <keybuk@google.com>
Acked-By: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: move regulatory_init to .init.text

regulatory_init is only called by cfg80211_init which is in .init.text,
too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add regulatory hint disconnect support

This adds a new regulatory hint to be used when we know all
devices have been disconnected and idle. This can happen
when we suspend, for instance. When we disconnect we can
no longer assume the same regulatory rules learned from
a country IE or beacon hints are applicable so restore
regulatory settings to an initial state.

Since driver hints are cached on the wiphy that called
the hint, those hints are not reproduced onto cfg80211
as the wiphy will respect its own wiphy->regd regardless.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: make regulatory_hint_11d() band specific

In practice APs do not send country IE channel triplets for channels
the AP is not operating on and if they were to do so they would have
to use the regulatory extension which we currently do not process.
No AP has been seen in practice that does this though so just drop
those country IEs.

Additionally it has been noted the first series of country IE
channels triplets are specific to the band the AP sends. Propagate
the band on which the country IE was found on reject the country
IE then if the triplets are ever oustide of the band.

Although we now won't process country IE information with multiple
band information we leave the intersection work as is as it is
technically possible for someone to want to eventually process these
type of country IEs with regulatory extensions.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: enable country IE support to all cfg80211 drivers

Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.

Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.

Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix regression on beacon world roaming feature

A regression was added through patch a4ed90d6:

"cfg80211: respect API on orig_flags on channel for beacon hint"

We did indeed respect _orig flags but the intention was not clearly
stated in the commit log. This patch fixes firmware issues picked
up by iwlwifi when we lift passive scan of beaconing restrictions
on channels its EEPROM has been configured to always enable.

By doing so though we also disallowed beacon hints on devices
registering their wiphy with custom world regulatory domains
enabled, this happens to be currently ath5k, ath9k and ar9170.
The passive scan and beacon restrictions on those devices would
never be lifted even if we did find a beacon and the hardware did
support such enhancements when world roaming.

Since Johannes indicates iwlwifi firmware cannot be changed to
allow beacon hinting we set up a flag now to specifically allow
drivers to disable beacon hints for devices which cannot use them.

We enable the flag on iwlwifi to disable beacon hints and by default
enable it for all other drivers. It should be noted beacon hints lift
passive scan flags and beacon restrictions when we receive a beacon from
an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz
band. We don't bother with channels 1-11 as those channels are allowed
world wide.

This should fix world roaming for ath5k, ath9k and ar9170, thereby
improving scan time when we receive the first beacon from any AP,
and also enabling beaconing operation (AP/IBSS/Mesh) on cards which
would otherwise not be allowed to do so. Drivers not using custom
regulatory stuff (wiphy_apply_custom_regulatory()) were not affected
by this as the orig_flags for the channels would have been cleared
upon wiphy registration.

I tested this with a world roaming ath5k card.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: make __regulatory_hint() static

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add AP beacon regulatory hints

When devices are world roaming they cannot beacon or do active scan
on 5 GHz or on channels 12, 13 and 14 on the 2 GHz band. Although
we have a good regulatory API some cards may _always_ world roam, this
is also true when a system does not have CRDA present. Devices doing world
roaming can still passive scan, if they find a beacon from an AP on
one of the world roaming frequencies we make the assumption we can do
the same and we also remove the passive scan requirement.

This adds support for providing beacon regulatory hints based on scans.
This works for devices that do either hardware or software scanning.
If a channel has not yet been marked as having had a beacon present
on it we queue the beacon hint processing into the workqueue.

All wireless devices will benefit from beacon regulatory hints from
any wireless device on a system including new devices connected to
the system at a later time.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: move all regulatory hints to workqueue

All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add get reg command

This lets userspace request to get the currently set
regulatory domain.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: pass more detailed regulatory request information on reg_notifier()

Drivers may need more information than just who set the last regulatory domain,
as such lets just pass the last regulatory_request receipt. To do this we need
to move out to headers struct regulatory_request, and enum environment_cap. While
at it lets add documentation for enum environment_cap.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: Add 802.11d support

This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.

To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.

A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.

In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.

CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: remove struct regdom hinting

The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: remove cfg80211_reg_mutex

This mutex is wrong, we use cfg80211_drv_mutex (which should
possibly be renamed to just cfg80211_mutex) everywhere except
in one place, fix that and get rid of the extra mutex.

Also get rid of a spurious regulatory_requests list definition.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: don't publish __regulatory_hint

This function requires an internal lock to be held, so it cannot
be published to other modules in the kernel.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix regulatory code const

A few pointers and structures in the regulatory code are const,
but because it wasn't done properly a whole bunch of bogus
casts were needed to compile without warning. Mark everything
const properly to avoid that kind of junk code.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: clean up regulatory mess

The recent code from Luis is an #ifdef hell and contains lots of
code that's stuffed into the wrong file making a whole bunch of
things needlessly non-static, and besides, what is it doing in
core.c??

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add new wireless regulatory infrastructure

This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:

* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel

We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.

Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.

Support for world roaming will be added soon for cards capable of
this.

For more information see:

http://wireless.kernel.org/en/developers/Regulatory/CRDA

For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>