Bluetooth: hci_sync: Use advertised PHYs on hci_le_ext_create_conn_sync

The extended advertising reports do report the PHYs so this store then
in hci_conn so it can be later used in hci_le_ext_create_conn_sync to
narrow the PHYs to be scanned since the controller will also perform a
scan having a smaller set of PHYs shall reduce the time it takes to
find and connect peers.

Fixes: 288c90224eec ("Bluetooth: Enable all supported LE PHY by default")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Fix overwriting request callback

In a few cases the stack may generate commands as responses to events
which would happen to overwrite the sent_cmd, so this attempts to store
the request in req_skb so even if sent_cmd is replaced with a new
command the pending request will remain in stored in req_skb.

Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Add hcon for listening bis sk

This creates a hcon instance at bis listen, before the PA sync
procedure is started.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Attempt to dequeue connection attempt

If connection is still queued/pending in the cmd_sync queue it means no
command has been generated and it should be safe to just dequeue the
callback when it is being aborted.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix UAF Write in __hci_acl_create_connection_sync

This fixes the UAF on __hci_acl_create_connection_sync caused by
connection abortion, it uses the same logic as to LE_LINK which uses
hci_cmd_sync_cancel to prevent the callback to run if the connection is
abort prematurely.

Reported-by: syzbot+3f0a39be7a2035700868@syzkaller.appspotmail.com
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Always use sk_timeo as conn_timeout

This aligns the use socket sk_timeo as conn_timeout when initiating a
connection and then use it when scheduling the resulting HCI command,
that way the command is actually aborted synchronously thus not
blocking commands generated by hci_abort_conn_sync to inform the
controller the connection is to be aborted.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Remove pending ACL connection attempts

With the last commit we moved to using the hci_sync queue for "Create
Connection" requests, removing the need for retrying the paging after
finished/failed "Create Connection" requests and after the end of
inquiries.

hci_conn_check_pending() was used to trigger this retry, we can remove it
now.

Note that we can also remove the special handling for COMMAND_DISALLOWED
errors in the completion handler of "Create Connection", because "Create
Connection" requests are now always serialized.

This is somewhat reverting commit 4c67bc74f016 ("[Bluetooth] Support
concurrent connect requests").

With this, the BT_CONNECT2 state of ACL hci_conn objects should now be
back to meaning only one thing: That we received a "Connection Request"
from another device (see hci_conn_request_evt), but the response to that
is going to be deferred.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Only do ACL connections sequentially

Pretty much all bluetooth chipsets only support paging a single device at
a time, and if they don't reject a secondary "Create Connection" request
while another is still ongoing, they'll most likely serialize those
requests in the firware.

With commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect
requests") we started adding some serialization of our own in case the
adapter returns "Command Disallowed" HCI error.

This commit was using the BT_CONNECT2 state for the serialization, this
state is also used for a few more things (most notably to indicate we're
waiting for an inquiry to cancel) and therefore a bit unreliable. Also
not all BT firwares would respond with "Command Disallowed" on too many
connection requests, some will also respond with "Hardware Failure"
(BCM4378), and others will error out later and send a "Connect Complete"
event with error "Rejected Limited Resources" (Marvell 88W8897).

We can clean things up a bit and also make the serialization more reliable
by using our hci_sync machinery to always do "Create Connection" requests
in a sequential manner.

This is very similar to what we're already doing for establishing LE
connections, and it works well there.

Note that this causes a test failure in mgmt-tester (test "Pair Device
- Power off 1") because the hci_abort_conn_sync() changes the error we
return on timeout of the "Create Connection". We'll fix this on the
mgmt-tester side by adjusting the expected error for the test.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Remove BT_HS

High Speed, Alternate MAC and PHY (AMP) extension, has been removed from
Bluetooth Core specification on 5.3:

https://www.bluetooth.com/blog/new-core-specification-v5-3-feature-enhancements/

Fixes: 244bc377591c ("Bluetooth: Add BT_HS config option")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Check non NULL function before calling for HFP offload

For some controllers such as QCA2066, it does not need to send
HCI_Configure_Data_Path to configure non-HCI data transport path to support
HFP offload, their device drivers may set hdev->get_codec_config_data as
NULL, so Explicitly add this non NULL checking before calling the function.

Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix bogus check for re-auth no supported with non-ssp

This reverts 19f8def031bfa50c579149b200bfeeb919727b27
"Bluetooth: Fix auth_complete_evt for legacy units" which seems to be
working around a bug on a broken controller rather then any limitation
imposed by the Bluetooth spec, in fact if there ws not possible to
re-auth the command shall fail not succeed.

Fixes: 19f8def031bf ("Bluetooth: Fix auth_complete_evt for legacy units")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Reassociate a socket with an active BIS

For ISO Broadcast, all BISes from a BIG have the same lifespan - they
cannot be created or terminated independently from each other.

This links together all BIS hcons that are part of the same BIG, so all
hcons are kept alive as long as the BIG is active.

If multiple BIS sockets are opened for a BIG handle, and only part of
them are closed at some point, the associated hcons will be marked as
open. If new sockets will later be opened for the same BIG, they will
be reassociated with the open BIS hcons.

All BIS hcons will be cleaned up and the BIG will be terminated when
the last BIS socket is closed from userspace.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix double free in hci_conn_cleanup

syzbot reports a slab use-after-free in hci_conn_hash_flush [1].
After releasing an object using hci_conn_del_sysfs in the
hci_conn_cleanup function, releasing the same object again
using the hci_dev_put and hci_conn_put functions causes a double free.
Here's a simplified flow:

hci_conn_del_sysfs:
hci_dev_put
put_device
kobject_put
kref_put
kobject_release
kobject_cleanup
kfree_const
kfree(name)

hci_dev_put:
...
kfree(name)

hci_conn_put:
put_device
...
kfree(name)

This patch drop the hci_dev_put and hci_conn_put function
call in hci_conn_cleanup function, because the object is
freed in hci_conn_del_sysfs function.

This patch also fixes the refcounting in hci_conn_add_sysfs() and
hci_conn_del_sysfs() to take into account device_add() failures.

This fixes CVE-2023-28464.

Link: https://syzkaller.appspot.com/bug?id=1bb51491ca5df96a5f724899d1dbb87afda61419 [1]

Signed-off-by: ZhengHan Wang <wzhmmmmm@gmail.com>
Co-developed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Make handle of hci_conn be unique

The handle of new hci_conn is always HCI_CONN_HANDLE_MAX + 1 if
the handle of the first hci_conn entry in hci_dev->conn_hash->list
is not HCI_CONN_HANDLE_MAX + 1. Use ida to manage the allocation of
hci_conn->handle to make it be unique.

Fixes: 9f78191cc9f1 ("Bluetooth: hci_conn: Always allocate unique handles")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Fix bcast listener cleanup

This fixes the cleanup callback for slave bis and pa sync hcons.

Closing all bis hcons will trigger BIG Terminate Sync, while closing
all bises and the pa sync hcon will also trigger PA Terminate Sync.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Match QoS adv handle with BIG handle

In case the user binds multiple sockets for the same BIG, the BIG
handle should be matched with the associated adv handle, if it has
already been allocated previously.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Allow binding a bcast listener to 0 bises

This makes it possible to bind a broadcast listener to a broadcaster
address without asking for any BIS indexes to sync with.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Pass BIG encryption info through QoS

This enables a broadcast sink to be informed if the PA
it has synced with is associated with an encrypted BIG,
by retrieving the socket QoS and checking the encryption
field.

After PA sync has been successfully established and the
first BIGInfo advertising report is received, a new hcon
is added and notified to the ISO layer. The ISO layer
sets the encryption field of the socket and hcon QoS
according to the encryption parameter of the BIGInfo
advertising report event.

After that, the userspace is woken up, and the QoS of the
new PA sync socket can be read, to inspect the encryption
field and follow up accordingly.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Fix BIS cleanup

This fixes the master BIS cleanup procedure - as opposed to CIS cleanup,
no HCI disconnect command should be issued. A master BIS should only be
terminated by disabling periodic and extended advertising, and terminating
the BIG.

In case of a Broadcast Receiver, all BIS and PA connections can be
cleaned up by calling hci_conn_failed, since it contains all function
calls that are necessary for successful cleanup.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Reject connection with the device which has same BD_ADDR

This change is used to relieve CVE-2020-26555. The description of
the CVE:

Bluetooth legacy BR/EDR PIN code pairing in Bluetooth Core Specification
1.0B through 5.2 may permit an unauthenticated nearby device to spoof
the BD_ADDR of the peer device to complete pairing without knowledge
of the PIN. [1]

The detail of this attack is in IEEE paper:
BlueMirror: Reflections on Bluetooth Pairing and Provisioning Protocols
[2]

It's a reflection attack. The paper mentioned that attacker can induce
the attacked target to generate null link key (zero key) without PIN
code. In BR/EDR, the key generation is actually handled in the controller
which is below HCI.

A condition of this attack is that attacker should change the
BR_ADDR of his hacking device (Host B) to equal to the BR_ADDR with
the target device being attacked (Host A).

Thus, we reject the connection with device which has same BD_ADDR
both on HCI_Create_Connection and HCI_Connection_Request to prevent
the attack. A similar implementation also shows in btstack project.
[3][4]

Cc: stable@vger.kernel.org
Link: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2020-26555 [1]
Link: https://ieeexplore.ieee.org/abstract/document/9474325/authors#authors [2]
Link: https://github.com/bluekitchen/btstack/blob/master/src/hci.c#L3523 [3]
Link: https://github.com/bluekitchen/btstack/blob/master/src/hci.c#L7297 [4]
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Avoid redundant authentication

While executing the Android 13 CTS Verifier Secure Server test on a
ChromeOS device, it was observed that the Bluetooth host initiates
authentication for an RFCOMM connection after SSP completes.
When this happens, some Intel Bluetooth controllers, like AC9560, would
disconnect with "Connection Rejected due to Security Reasons (0x0e)".

Historically, BlueZ did not mandate this authentication while an
authenticated combination key was already in use for the connection.
This behavior was changed since commit 7b5a9241b780
("Bluetooth: Introduce requirements for security level 4").
So, this patch addresses the aforementioned disconnection issue by
restoring the previous behavior.

Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: fail SCO/ISO via hci_conn_failed if ACL gone early

Not calling hci_(dis)connect_cfm before deleting conn referred to by a
socket generally results to use-after-free.

When cleaning up SCO connections when the parent ACL is deleted too
early, use hci_conn_failed to do the connection cleanup properly.

We also need to clean up ISO connections in a similar situation when
connecting has started but LE Create CIS is not yet sent, so do it too
here.

Fixes: ca1fd42e7dbf ("Bluetooth: Fix potential double free caused by hci_conn_unlink")
Reported-by: syzbot+cf54c1da6574b6c1b049@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/00000000000013b93805fbbadc50@google.com/
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Use defer setup to separate PA sync and BIG sync

This commit implements defer setup support for the Broadcast Sink
scenario: By setting defer setup on a broadcast socket before calling
listen, the user is able to trigger the PA sync and BIG sync procedures
separately.

This is useful if the user first wants to synchronize to the periodic
advertising transmitted by a Broadcast Source, and trigger the BIG sync
procedure later on.

If defer setup is set, once a PA sync established event arrives, a new
hcon is created and notified to the ISO layer. A child socket associated
with the PA sync connection will be added to the accept queue of the
listening socket.

Once the accept call returns the fd for the PA sync child socket, the
user should call read on that fd. This will trigger the BIG create sync
procedure, and the PA sync socket will become a listening socket itself.

When the BIG sync established event is notified to the ISO layer, the
bis connections will be added to the accept queue of the PA sync parent.
The user should call accept on the PA sync socket to get the final bis
connections.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix sending BT_HCI_CMD_LE_CREATE_CONN_CANCEL

This fixes sending BT_HCI_CMD_LE_CREATE_CONN_CANCEL when
hci_le_create_conn_sync has not been called because HCI_CONN_SCANNING
has been clear too early before its cmd_sync callback has been run.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: avoid checking uninitialized CIG/CIS ids

The CIS/CIG ids of ISO connections are defined only when the connection
is unicast.

Fix the lookup functions to check for unicast first. Ensure CIG/CIS
IDs have valid value also in state BT_OPEN.

Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Introduce PTR_UINT/UINT_PTR macros

This introduces PTR_UINT/UINT_PTR macros and replace the use of
PTR_ERR/ERR_PTR.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix hci_le_set_cig_params

When running with concurrent task only one CIS was being assigned so
this attempts to rework the way the PDU is constructed so it is handled
later at the callback instead of in place.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix not allowing valid CIS ID

Only the number of CIS shall be limited to 0x1f, the CIS ID in the
other hand is up to 0xef.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix modifying handle while aborting

This introduces hci_conn_set_handle which takes care of verifying the
conditions where the hci_conn handle can be modified, including when
hci_conn_abort has been called and also checks that the handles is
valid as well.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: handle bound CIS cleanup via hci_conn

Calling hci_conn_del in __iso_sock_close is invalid. It needs
hdev->lock, but it cannot be acquired there due to lock ordering.

Fix this by doing cleanup via hci_conn_drop.

Return hci_conn with refcount 1 from hci_bind_cis and hci_connect_cis,
so that the iso_conn always holds one reference. This also fixes
refcounting when error handling.

Since hci_conn_abort shall handle termination of connections in any
state properly, we can handle BT_CONNECT socket state in the same way as
BT_CONNECTED.

Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Notify user space about failed bis connections

Some use cases require the user to be informed if BIG synchronization
fails. This commit makes it so that even if the BIG sync established
event arrives with error status, a new hconn is added for each BIS,
and the iso layer is notified about the failed connections.

Unsuccesful bis connections will be marked using the
HCI_CONN_BIG_SYNC_FAILED flag. From the iso layer, the POLLERR event
is triggered on the newly allocated bis sockets, before adding them
to the accept list of the parent socket.

From user space, a new fd for each failed bis connection will be
obtained by calling accept. The user should check for the POLLERR
event on the new socket, to determine if the connection was successful
or not.

The HCI_CONN_BIG_SYNC flag has been added to mark whether the BIG sync
has been successfully established. This flag is checked at bis cleanup,
so the HCI LE BIG Terminate Sync command is only issued if needed.

The BT_SK_BIG_SYNC flag indicates if BIG create sync has been called
for a listening socket, to avoid issuing the command everytime a BIGInfo
advertising report is received.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Always allocate unique handles

This attempts to always allocate a unique handle for connections so they
can be properly aborted by the likes of hci_abort_conn, so this uses the
invalid range as a pool of unset handles that way if userspace is trying
to create multiple connections at once each will be given a unique
handle which will be considered unset.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Fix not handling ISO_LINK in hci_abort_conn_sync

ISO_LINK connections where not being handled properly on
hci_abort_conn_sync which sometimes resulted in sending the wrong
commands, or in case of having the reject command being sent by the
socket code (iso.c) which is sort of a layer violation.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Consolidate code for aborting connections

This consolidates code for aborting connections using
hci_cmd_sync_queue so it is synchronized with other threads, but
because of the fact that some commands may block the cmd_sync_queue
while waiting specific events this attempt to cancel those requests by
using hci_cmd_sync_cancel.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Support multiple BIGs

This adds support for creating multiple BIGs. According to
spec, each BIG shall have an unique handle, and each BIG should
be associated with a different advertising handle. Otherwise,
the LE Create BIG command will fail, with error code
Command Disallowed (for reusing a BIG handle), or
Unknown Advertising Identifier (for reusing an advertising
handle).

The btmon snippet below shows an exercise for creating two BIGs
for the same controller, by opening two isotest instances with
the following command:
tools/isotest -i hci0 -s 00:00:00:00:00:00

< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x00
Advertising Handle: 0x01
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000

> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)

> HCI Event: LE Meta Event (0x3e) plen 21
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x00
BIG Synchronization Delay: 912 us (0x000390)
Transport Latency: 912 us (0x000390)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10

< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068)
Handle: 0x01
Advertising Handle: 0x02
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000

> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: do not emit new LE Create CIS if previous is pending

LE Create CIS command shall not be sent before all CIS Established
events from its previous invocation have been processed. Currently it is
sent via hci_sync but that only waits for the first event, but there can
be multiple.

Make it wait for all events, and simplify the CIS creation as follows:

Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been
sent for the connection but it is not yet completed.

Make BT_CONNECT state to mean the connection wants Create CIS.

On events after which new Create CIS may need to be sent, send it if
possible and some connections need it. These events are:
hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis,
hci_le_cis_estabilished_evt.

The Create CIS status/completion events shall queue new Create CIS only
if at least one of the connections transitions away from BT_CONNECT, so
that we don't loop if controller is sending bogus events.

This fixes sending multiple CIS Create for the same CIS in the
"ISO AC 6(i) - Success" BlueZ test case:

< HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0]
Number of CIS: 2
CIS Handle: 257
ACL Handle: 42
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #130 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 257
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0]
...
> HCI Event: Command Complete (0x0e) plen 6 #133 [hci0]
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
...
< HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0]
Number of CIS: 1
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #135 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: ACL Connection Already Exists (0x0b)
> HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 258
...

Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Add support for connecting multiple BISes

It is required for some configurations to have multiple BISes as part
of the same BIG.

Similar to the flow implemented for unicast, DEFER_SETUP will also be
used to bind multiple BISes for the same BIG, before starting Periodic
Advertising and creating the BIG.

The user will have to open a new socket for each BIS. By setting the
BT_DEFER_SETUP socket option and calling connect, a new connection
will be added for the BIG and advertising handle set by the socket
QoS parameters. Since all BISes will be bound for the same BIG and
advertising handle, the socket QoS options and base parameters should
match for all connections.

By calling connect on a socket that does not have the BT_DEFER_SETUP
option set, periodic advertising will be started and the BIG will
be created, with a BIS for each previously bound connection. Since
a BIG cannot be reconfigured with additional BISes after creation,
no more connections can be bound for the BIG after the start periodic
advertising and create BIG commands have been queued.

The bis_cleanup function has also been updated, so that the advertising
set and the BIG will not be terminated unless there are no more
bound or connected BISes.

The HCI_CONN_BIG_CREATED connection flag has been added to indicate
that the BIG has been successfully created. This flag is checked at
bis_cleanup, so that the BIG is only terminated if the
HCI_LE_Create_BIG_Complete has been received.

This implementation has been tested on hardware, using the "isotest"
tool with an additional command line option, to specify the number of
BISes to create as part of the desired BIG:

tools/isotest -i hci0 -s 00:00:00:00:00:00 -N 2 -G 1 -T 1

The btmon log shows that a BIG containing 2 BISes has been created:

< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x01
Advertising Handle: 0x01
Number of BIS: 2
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000

> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)

> HCI Event: LE Meta Event (0x3e) plen 23
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x01
BIG Synchronization Delay: 1974 us (0x0007b6)
Transport Latency: 1974 us (0x0007b6)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10
Connection Handle #1: 11

< HCI Command: LE Setup Isochronous Data Path (0x08|0x006e) plen 13
Handle: 10
Data Path Direction: Input (Host to Controller) (0x00)
Data Path: HCI (0x00)
Coding Format: Transparent (0x03)
Company Codec ID: Ericsson Technology Licensing (0)
Vendor Codec ID: 0
Controller Delay: 0 us (0x000000)
Codec Configuration Length: 0
Codec Configuration:

> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 10

< HCI Command: LE Setup Isochronous Data Path (0x08|0x006e) plen 13
Handle: 11
Data Path Direction: Input (Host to Controller) (0x00)
Data Path: HCI (0x00)
Coding Format: Transparent (0x03)
Company Codec ID: Ericsson Technology Licensing (0)
Vendor Codec ID: 0
Controller Delay: 0 us (0x000000)
Codec Configuration Length: 0
Codec Configuration:

> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 11

< ISO Data TX: Handle 10 flags 0x02 dlen 44

< ISO Data TX: Handle 11 flags 0x02 dlen 44

> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 10
Count: 1

> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 11
Count: 1

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: return ERR_PTR instead of NULL when there is no link

hci_connect_sco currently returns NULL when there is no link (i.e. when
hci_conn_link() returns NULL).

sco_connect() expects an ERR_PTR in case of any error (see line 266 in
sco.c). Thus, hcon set as NULL passes through to sco_conn_add(), which
tries to get hcon->hdev, resulting in dereferencing a NULL pointer as
reported by syzkaller.

The same issue exists for iso_connect_cis() calling hci_connect_cis().

Thus, make hci_connect_sco() and hci_connect_cis() return ERR_PTR
instead of NULL.

Reported-and-tested-by: syzbot+37acd5d80d00d609d233@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=37acd5d80d00d609d233
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync

hci_update_accept_list_sync iterates over hdev->pend_le_conns and
hdev->pend_le_reports, and waits for controller events in the loop body,
without holding hdev lock.

Meanwhile, these lists and the items may be modified e.g. by
le_scan_cleanup. This can invalidate the list cursor or any other item
in the list, resulting to invalid behavior (eg use-after-free).

Use RCU for the hci_conn_params action lists. Since the loop bodies in
hci_sync block and we cannot use RCU or hdev->lock for the whole loop,
copy list items first and then iterate on the copy. Only the flags field
is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we
read valid values.

Free params everywhere with hci_conn_params_free so the cleanup is
guaranteed to be done properly.

This fixes the following, which can be triggered e.g. by BlueZ new
mgmt-tester case "Add + Remove Device Nowait - Success", or by changing
hci_le_set_cig_params to always return false, and running iso-tester:

==================================================================
BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32

Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107)
print_report (mm/kasan/report.c:320 mm/kasan/report.c:430)
? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65)
? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
kasan_report (mm/kasan/report.c:538)
? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780)
? mutex_lock (kernel/locking/mutex.c:282)
? __pfx_mutex_lock (kernel/locking/mutex.c:282)
? __pfx_mutex_unlock (kernel/locking/mutex.c:538)
? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861)
hci_cmd_sync_work (net/bluetooth/hci_sync.c:306)
process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538)
? __pfx_worker_thread (kernel/workqueue.c:2480)
kthread (kernel/kthread.c:376)
? __pfx_kthread (kernel/kthread.c:331)
ret_from_fork (arch/x86/entry/entry_64.S:314)
</TASK>

Allocated by task 31:
kasan_save_stack (mm/kasan/common.c:46)
kasan_set_track (mm/kasan/common.c:52)
__kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383)
hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277)
hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589)
hci_connect_cis (net/bluetooth/hci_conn.c:2266)
iso_connect_cis (net/bluetooth/iso.c:390)
iso_sock_connect (net/bluetooth/iso.c:899)
__sys_connect (net/socket.c:2003 net/socket.c:2020)
__x64_sys_connect (net/socket.c:2027)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)

Freed by task 15:
kasan_save_stack (mm/kasan/common.c:46)
kasan_set_track (mm/kasan/common.c:52)
kasan_save_free_info (mm/kasan/generic.c:523)
__kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244)
__kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800)
hci_conn_params_del (net/bluetooth/hci_core.c:2323)
le_scan_cleanup (net/bluetooth/hci_conn.c:202)
process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:314)
==================================================================

Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Use kmemdup() to replace kzalloc + memcpy

Use kmemdup rather than duplicating its implementation.

./net/bluetooth/hci_conn.c:1880:7-14: WARNING opportunity for kmemdup.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5597
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Bluetooth: ISO: Rework sync_interval to be sync_factor

This rework sync_interval to be sync_factor as having sync_interval in
the order of seconds is sometimes not disarable.

Wit sync_factor the application can tell how many SDU intervals it wants
to send an announcement with PA, the EA interval is set to 2 times that
so a factor of 24 of BIG SDU interval of 10ms would look like the
following:

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 480.000 msec (0x0300)
Max advertising interval: 480.000 msec (0x0300)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x00
Scan request notifications: Disabled (0x00)
< HCI Command: LE Set Periodic Advertising Parameters (0x08|0x003e) plen 7
Handle: 1
Min interval: 240.00 msec (0x00c0)
Max interval: 240.00 msec (0x00c0)
Properties: 0x0000

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Bluetooth: ISO: use hci_sync for setting CIG parameters

When reconfiguring CIG after disconnection of the last CIS, LE Remove
CIG shall be sent before LE Set CIG Parameters. Otherwise, it fails
because CIG is in the inactive state and not configurable (Core v5.3
Vol 6 Part B Sec. 4.5.14.3). This ordering is currently wrong under
suitable timing conditions, because LE Remove CIG is sent via the
hci_sync queue and may be delayed, but Set CIG Parameters is via
hci_send_cmd.

Make the ordering well-defined by sending also Set CIG Parameters via
hci_sync.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Bluetooth: ISO: don't try to remove CIG if there are bound CIS left

Consider existing BOUND & CONNECT state CIS to block CIG removal.
Otherwise, under suitable timing conditions we may attempt to remove CIG
while Create CIS is pending, which fails.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Fix CIG auto-allocation to select configurable CIG

Make CIG auto-allocation to select the first CIG_ID that is still
configurable. Also use correct CIG_ID range (see Core v5.3 Vol 4 Part E
Sec 7.8.97 p.2553).

Previously, it would always select CIG_ID 0 regardless of anything,
because cis_list with data.cis == 0xff (BT_ISO_QOS_CIS_UNSET) would not
count any CIS. Since we are not adding CIS here, use find_cis instead.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: consider right CIS when removing CIG at cleanup

When looking for CIS blocking CIG removal, consider only the CIS with
the right CIG ID. Don't try to remove CIG with unset CIG ID.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Unlink CISes when LE disconnects in hci_conn_del

Currently, hci_conn_del calls hci_conn_unlink for BR/EDR, (e)SCO, and
CIS connections, i.e., everything except LE connections. However, if
(e)SCO connections are unlinked when BR/EDR disconnects, CIS connections
should also be unlinked when LE disconnects.

In terms of disconnection behavior, CIS and (e)SCO connections are not
too different. One peculiarity of CIS is that when CIS connections are
disconnected, the CIS handle isn't deleted, as per [BLUETOOTH CORE
SPECIFICATION Version 5.4 | Vol 4, Part E] 7.1.6 Disconnect command:

All SCO, eSCO, and CIS connections on a physical link should be
disconnected before the ACL connection on the same physical
connection is disconnected. If it does not, they will be
implicitly disconnected as part of the ACL disconnection.
...
Note: As specified in Section 7.7.5, on the Central, the handle
for a CIS remains valid even after disconnection and, therefore,
the Host can recreate a disconnected CIS at a later point in
time using the same connection handle.

Since hci_conn_link invokes both hci_conn_get and hci_conn_hold,
hci_conn_unlink should perform both hci_conn_put and hci_conn_drop as
well. However, currently it performs only hci_conn_put.

This patch makes hci_conn_unlink call hci_conn_drop as well, which
simplifies the logic in hci_conn_del a bit and may benefit future users
of hci_conn_unlink. But it is noted that this change additionally
implies that hci_conn_unlink can queue disc_work on conn itself, with
the following call stack:

hci_conn_unlink(conn) [conn->parent == NULL]
-> hci_conn_unlink(child) [child->parent == conn]
-> hci_conn_drop(child->parent)
-> queue_delayed_work(&conn->disc_work)

Queued disc_work after hci_conn_del can be spurious, so during the
process of hci_conn_del, it is necessary to make the call to
cancel_delayed_work(&conn->disc_work) after invoking hci_conn_unlink.

Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix UAF in hci_conn_hash_flush again

Commit 06149746e720 ("Bluetooth: hci_conn: Add support for linking
multiple hcon") reintroduced a previously fixed bug [1] ("KASAN:
slab-use-after-free Read in hci_conn_hash_flush"). This bug was
originally fixed by commit 5dc7d23e167e ("Bluetooth: hci_conn: Fix
possible UAF").

The hci_conn_unlink function was added to avoid invalidating the link
traversal caused by successive hci_conn_del operations releasing extra
connections. However, currently hci_conn_unlink itself also releases
extra connections, resulted in the reintroduced bug.

This patch follows a more robust solution for cleaning up all
connections, by repeatedly removing the first connection until there are
none left. This approach does not rely on the inner workings of
hci_conn_del and ensures proper cleanup of all connections.

Meanwhile, we need to make sure that hci_conn_del never fails. Indeed it
doesn't, as it now always returns zero. To make this a bit clearer, this
patch also changes its return type to void.

Reported-by: syzbot+8bb72f86fc823817bc5d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/000000000000aa920505f60d25ad@google.com/
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Refcnt drop must be placed last in hci_conn_unlink

If hci_conn_put(conn->parent) reduces conn->parent's reference count to
zero, it can immediately deallocate conn->parent. At the same time,
conn->link->list has its head in conn->parent, causing use-after-free
problems in the latter list_del_rcu(&conn->link->list).

This problem can be easily solved by reordering the two operations,
i.e., first performing the list removal with list_del_rcu and then
decreasing the refcnt with hci_conn_put.

Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Closes: https://lore.kernel.org/linux-bluetooth/CABBYNZ+1kce8_RJrLNOXd_8=Mdpb=2bx4Nto-hFORk=qiOkoCg@mail.gmail.com/
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix potential double free caused by hci_conn_unlink

The hci_conn_unlink function is being called by hci_conn_del, which
means it should not call hci_conn_del with the input parameter conn
again. If it does, conn may have already been released when
hci_conn_unlink returns, leading to potential UAF and double-free
issues.

This patch resolves the problem by modifying hci_conn_unlink to release
only conn's child links when necessary, but never release conn itself.

Reported-by: syzbot+690b90b14f14f43f4688@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/000000000000484a8205faafe216@google.com/
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reported-by: syzbot+690b90b14f14f43f4688@syzkaller.appspotmail.com
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reported-by: syzbot+8bb72f86fc823817bc5d@syzkaller.appspotmail.com

Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED

When submitting HCI_OP_LE_CREATE_CIS the code shall wait for
HCI_EVT_LE_CIS_ESTABLISHED thus enforcing the serialization of
HCI_OP_LE_CREATE_CIS as the Core spec does not allow to send them in
parallel:

BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E page 2566:

If the Host issues this command before all the HCI_LE_CIS_Established
events from the previous use of the command have been generated, the
Controller shall return the error code Command Disallowed (0x0C).

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix not matching by CIS ID

This fixes only matching CIS by address which prevents creating new hcon
if upper layer is requesting a specific CIS ID.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Add support for linking multiple hcon

Since it is required for some configurations to have multiple CIS with
the same peer which is now covered by iso-tester in the following test
cases:

ISO AC 6(i) - Success
ISO AC 7(i) - Success
ISO AC 8(i) - Success
ISO AC 9(i) - Success
ISO AC 11(i) - Success

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: remove extra line in hci_le_big_create_sync

Remove extra line setting the broadcast code parameter of the
hci_cp_le_create_big struct to 0. The broadcast code is copied
from the QoS struct.

Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Split bt_iso_qos into dedicated structures

Split bt_iso_qos into dedicated unicast and broadcast
structures and add additional broadcast parameters.

Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix possible UAF

This fixes the following trace:

==================================================================
BUG: KASAN: slab-use-after-free in hci_conn_del+0xba/0x3a0
Write of size 8 at addr ffff88800208e9c8 by task iso-tester/31

CPU: 0 PID: 31 Comm: iso-tester Not tainted 6.3.0-rc2-g991aa4a69a47
#4716
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.1-2.fc36
04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x1d/0x70
print_report+0xce/0x610
? __virt_addr_valid+0xd4/0x150
? hci_conn_del+0xba/0x3a0
kasan_report+0xdd/0x110
? hci_conn_del+0xba/0x3a0
hci_conn_del+0xba/0x3a0
hci_conn_hash_flush+0xf2/0x120
hci_dev_close_sync+0x388/0x920
hci_unregister_dev+0x122/0x260
vhci_release+0x4f/0x90
__fput+0x102/0x430
task_work_run+0xf1/0x160
? __pfx_task_work_run+0x10/0x10
? mark_held_locks+0x24/0x90
exit_to_user_mode_prepare+0x170/0x180
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x4e/0x90
entry_SYSCALL_64_after_hwframe+0x70/0xda

Fixes: 0f00cd322d22 ("Bluetooth: Free potentially unfreed SCO connection")
Link: https://syzkaller.appspot.com/bug?extid=8bb72f86fc823817bc5d
Cc: <stable@vger.kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix printing errors if LE Connection times out

This fixes errors like bellow when LE Connection times out since that
is actually not a controller error:

Bluetooth: hci0: Opcode 0x200d failed: -110
Bluetooth: hci0: request failed to create LE connection: err -110

Instead the code shall properly detect if -ETIMEDOUT is returned and
send HCI_OP_LE_CREATE_CONN_CANCEL to give up on the connection.

Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60de ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix not cleaning up on LE Connection failure

hci_connect_le_scan_cleanup shall always be invoked to cleanup the
states and re-enable passive scanning if necessary, otherwise it may
cause the pending action to stay active causing multiple attempts to
connect.

Fixes: 9b3628d79b46 ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Make sure LE create conn cancel is sent when timeout

When sending LE create conn command, we set a timer with a duration of
HCI_LE_CONN_TIMEOUT before timing out and calling
create_le_conn_complete. Additionally, when receiving the command
complete, we also set a timer with the same duration to call
le_conn_timeout.

Usually the latter will be triggered first, which then sends a LE
create conn cancel command. However, due to the nature of racing, it
is possible for the former to be called first, thereby calling the
chain hci_conn_failed -> hci_conn_del -> cancel_delayed_work, thereby
preventing LE create conn cancel to be sent. In this situation, the
controller will be stuck in trying the LE connection.

This patch flushes le_conn_timeout on create_le_conn_complete to make
sure we always send LE create connection cancel, if necessary.

Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Free potentially unfreed SCO connection

It is possible to initiate a SCO connection while deleting the
corresponding ACL connection, e.g. in below scenario:

(1) < hci setup sync connect command
(2) > hci disconn complete event (for the acl connection)
(3) > hci command complete event (for(1), failure)

When it happens, hci_cs_setup_sync_conn won't be able to obtain the
reference to the SCO connection, so it will be stuck and potentially
hinder subsequent connections to the same device.

This patch prevents that by also deleting the SCO connection if it is
still not established when the corresponding ACL connection is deleted.

Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Refactor hci_bind_bis() since it always succeeds

The compiler thinks "conn" might be NULL after a call to hci_bind_bis(),
which cannot happen. Avoid any confusion by just making it not return a
value since it cannot fail. Fixes the warnings seen with GCC 13:

In function 'arch_atomic_dec_and_test',
inlined from 'atomic_dec_and_test' at ../include/linux/atomic/atomic-instrumented.h:576:9,
inlined from 'hci_conn_drop' at ../include/net/bluetooth/hci_core.h:1391:6,
inlined from 'hci_connect_bis' at ../net/bluetooth/hci_conn.c:2124:3:
../arch/x86/include/asm/rmwcc.h:37:9: warning: array subscript 0 is outside array bounds of 'atomic_t[0]' [-Warray-bounds=]
37 | asm volatile (fullop CC_SET(cc) \
| ^~~
...
In function 'hci_connect_bis':
cc1: note: source object is likely at address zero

Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix memory leaks

When hci_cmd_sync_queue() failed in hci_le_terminate_big() or
hci_le_big_terminate(), the memory pointed by variable d is not freed,
which will cause memory leak. Add release process to error path.

Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix crash on hci_create_cis_sync

When attempting to connect multiple ISO sockets without using
DEFER_SETUP may result in the following crash:

BUG: KASAN: null-ptr-deref in hci_create_cis_sync+0x18b/0x2b0
Read of size 2 at addr 0000000000000036 by task kworker/u3:1/50

CPU: 0 PID: 50 Comm: kworker/u3:1 Not tainted
6.0.0-rc7-02243-gb84a13ff4eda #4373
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009),
BIOS 1.16.0-1.fc36 04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl+0x19/0x27
kasan_report+0xbc/0xf0
? hci_create_cis_sync+0x18b/0x2b0
hci_create_cis_sync+0x18b/0x2b0
? get_link_mode+0xd0/0xd0
? __ww_mutex_lock_slowpath+0x10/0x10
? mutex_lock+0xe0/0xe0
? get_link_mode+0xd0/0xd0
hci_cmd_sync_work+0x111/0x190
process_one_work+0x427/0x650
worker_thread+0x87/0x750
? process_one_work+0x650/0x650
kthread+0x14e/0x180
? kthread_exit+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Use kzalloc instead of kmalloc/memset

Replace kmalloc+memset by kzalloc
for better readability and simplicity.

This addresses the cocci warning below:

WARNING: kzalloc should be used for d, instead of kmalloc/memset

Signed-off-by: Kang Minchul <tegongkang@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Use kzalloc instead of kmalloc/memset

Use kzalloc rather than duplicating its implementation, which makes code
simple and easy to understand.

./net/bluetooth/hci_conn.c:2038:6-13: WARNING: kzalloc should be used for cp, instead of kmalloc/memset.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2406
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: use HCI dst_type values also for BIS

For ISO BIS related functions in hci_conn.c, make dst_type values be HCI
address type values, not ISO socket address type values. This makes it
consistent with CIS functions.

Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix not restoring ISO buffer count on disconnect

When disconnecting an ISO link the controller may not generate
HCI_EV_NUM_COMP_PKTS for unacked packets which needs to be restored in
hci_conn_del otherwise the host would assume they are still in use and
would not be able to use all the buffers available.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Frédéric Danis <frederic.danis@collabora.com>

Bluetooth: hci_conn: Fix CIS connection dst_type handling

hci_connect_cis and iso_connect_cis call hci_bind_cis inconsistently
with dst_type being either ISO socket address type or the HCI type, but
these values cannot be mixed like this. Fix this by using only the HCI
type.

CIS connection dst_type was also not initialized in hci_bind_cis, even
though it is used in hci_conn_hash_lookup_cis to find existing
connections. Set the value in hci_bind_cis, so that existing CIS
connections are found e.g. when doing deferred socket connections, also
when dst_type is not 0 (ADDR_LE_DEV_PUBLIC).

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Move hci_abort_conn to hci_conn.c

hci_abort_conn() is a wrapper around a number of DISCONNECT and
CREATE_CONN_CANCEL commands that was being invoked from hci_request
request queues, which are now deprecated. There are two versions:
hci_abort_conn() which can be invoked from the hci_event thread, and
hci_abort_conn_sync() which can be invoked within a hci_sync cmd chain.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Convert SCO configure_datapath to hci_sync

Recoding HCI cmds to offload SCO codec to use hci_sync mechanism rather
than deprecated hci_request mechanism.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix updating ISO QoS PHY

BT_ISO_QOS has different semantics when it comes to QoS PHY as it uses
0x00 to disable a direction but that value is invalid over HCI and
sockets using DEFER_SETUP to connect may attempt to use hci_bind_cis
multiple times in order to detect if the parameters have changed, so to
fix the code will now just mirror the PHY for the parameters of
HCI_OP_LE_SET_CIG_PARAMS and will not update the PHY of the socket
leaving it disabled.

Fixes: 26afbd826ee32 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Add initial implementation of BIS connections

This adds initial support for BIS/BIG which includes:

== Broadcaster role: Setup a periodic advertising and create a BIG ==

> tools/isotest -s 00:00:00:00:00:00
isotest[63]: Connected [00:00:00:00:00:00]
isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00]
isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02
RTN 2]
isotest[63]: Sending ...
isotest[63]: Number of packets: 1
isotest[63]: Socket jitter buffer: 80 buffer
< HCI Command: LE Set Perio.. (0x08|0x003e) plen 7
...
> HCI Event: Command Complete (0x0e) plen 4
LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Perio.. (0x08|0x003f) plen 7
...
> HCI Event: Command Complete (0x0e) plen 4
LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Perio.. (0x08|0x0040) plen 2
...
> HCI Event: Command Complete (0x0e) plen 4
LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create B.. (0x08|0x0068) plen 31
...
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 21
LE Broadcast Isochronous Group Complete (0x1b)
...

== Broadcast Receiver role: Create a PA Sync and BIG Sync ==

> tools/isotest -i hci1 -d 00:AA:01:00:00:00
isotest[66]: Waiting for connection 00:AA:01:00:00:00...
< HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14
...
> HCI Event: Command Status (0x0f) plen 4
LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8
...
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6
...
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Enable (0x08|0x0042) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29
LE Extended Advertising Report (0x0d)
...
> HCI Event: LE Meta Event (0x3e) plen 16
LE Periodic Advertising Sync Established (0x0e)
...
< HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25
...
> HCI Event: Command Status (0x0f) plen 4
LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 17
LE Broadcast Isochronous Group Sync Estabilished (0x1d)
...

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Add initial implementation of CIS connections

This adds the initial implementation of CIS connections and introduces
the ISO packets/links.

== Central: Set CIG Parameters, create a CIS and Setup Data Path ==

> tools/isotest -s <address>

< HCI Command: LE Extended Create... (0x08|0x0043) plen 26
...
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
...
< HCI Command: LE Create Connected... (0x08|0x0064) plen 5
...
> HCI Event: Command Status (0x0f) plen 4
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29
LE Connected Isochronous Stream Established (0x19)
...
< HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257
< HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257

== Peripheral: Accept CIS and Setup Data Path ==

> tools/isotest -d

HCI Event: LE Meta Event (0x3e) plen 7
LE Connected Isochronous Stream Request (0x1a)
...
< HCI Command: LE Accept Co.. (0x08|0x0066) plen 2
...
> HCI Event: LE Meta Event (0x3e) plen 29
LE Connected Isochronous Stream Established (0x19)
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Use bt_status to convert from errno

If a command cannot be sent or there is a internal error an errno maybe
set instead of a command status.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: clear the temporary linkkey in hci_conn_cleanup

If a hardware error occurs and the connections are flushed without a
disconnection_complete event being signaled, the temporary linkkeys are
not flushed.

This change ensures that any outstanding flushable linkkeys are flushed
when the connection are flushed from the hash table.

Additionally, this also makes use of test_and_clear_bit to avoid
multiple attempts to delete the link key that's already been flushed.

Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_conn: Fix hci_connect_le_sync

The handling of connection failures shall be handled by the request
completion callback as already done by hci_cs_le_create_conn, also make
sure to use hci_conn_failed instead of hci_le_conn_failed as the later
don't actually call hci_conn_del to cleanup.

Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60de5 ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: HCI: Add HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk

This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted

This attempts to cleanup the hci_conn if it cannot be aborted as
otherwise it would likely result in having the controller and host
stack out of sync with respect to connection handle.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: call hci_le_conn_failed with hdev lock in hci_le_conn_failed

hci_le_conn_failed function's documentation says that the caller must
hold hdev->lock. The only callsite that does not hold that lock is
hci_le_conn_failed. The other 3 callsites hold the hdev->lock very
locally. The solution is to hold the lock during the call to
hci_le_conn_failed.

Fixes: 3c857757ef6e ("Bluetooth: Add directed advertising support through connect()")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_event: Ignore multiple conn complete events

When one of the three connection complete events is received multiple
times for the same handle, the device is registered multiple times which
leads to memory corruptions. Therefore, consequent events for a single
connection are ignored.

The conn->state can hold different values, therefore HCI_CONN_HANDLE_UNSET
is introduced to identify new connections. To make sure the events do not
contain this or another invalid handle HCI_CONN_HANDLE_MAX and checks
are introduced.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=215497
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Add hci_le_create_conn_sync

This adds hci_le_create_conn_sync and make hci_le_connect use it instead
of queueing multiple commands which may conflict with the likes of
hci_update_passive_scan which uses hci_cmd_sync_queue.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_sync: Rework hci_suspend_notifier

This makes hci_suspend_notifier use the hci_*_sync which can be
executed synchronously which is allowed in the suspend_notifier and
simplifies a lot of the handling since the status of each command can
be checked inline so no other work need to be scheduled thus can be
performed without using of a state machine.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY

This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY,
MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use
hci_cmd_sync_queue so they no longer depend on hdev->discov_update work
to send any commands.

Tested with:

tools/mgmt-tester -s "Start Discovery"

Test Summary
------------
Start Discovery - Not powered 1 Passed
Start Discovery - Invalid parameters 1 Passed
Start Discovery - Not supported 1 Passed
Start Discovery - Success 1 Passed
Start Discovery - Success 2 Passed
Start Discovery - Power Off 1 Passed
Start Discovery BREDR LE - (Ext Scan Enable) Passed
Start Discovery LE - (Ext Scan Enable) Passed
Start Discovery LE - (Ext Scan Param) Passed
Start Discovery - (2m, Scan Param) Passed
Start Discovery - (coded, Scan Param) Passed
Start Discovery - (1m, 2m, coded, Scan Param) Passed
LL Privacy - Start Discovery 1 (Disable RL) Passed
LL Privacy - Start Discovery 2 (Disable RL) Passed
Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0

tools/mgmt-tester -s "Start Service"

Test Summary
------------
Start Service Discovery - Not powered 1 Passed
Start Service Discovery - Invalid parameters 1 Passed
Start Service Discovery - Not supported 1 Passed
Start Service Discovery - Success 1 Passed
Start Service Discovery - Success 2 Passed
Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0

tools/mgmt-tester -s "Stop Discovery"

Test Summary
------------
Stop Discovery - Success 1 Passed
Stop Discovery - BR/EDR (Inquiry) Success 1 Passed
Stop Discovery - Rejected 1 Passed
Stop Discovery - Invalid parameters 1 Passed
Stop Discovery - (Ext Scan Disable) Passed
Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_sync: Rework background scan

This replaces the use of hci_update_background_scan with
hci_update_passive_scan which runs from cmd_work_sync and deal properly
with resolving list when LL privacy is enabled.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add support for msbc coding format

In Enhanced_Setup_Synchronous_Command, add support for msbc
coding format

Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Configure codec for HFP offload use case

For HFP offload use case, codec needs to be configured
before opening SCO connection. This patch sends
HCI_CONFIGURE_DATA_PATH command to configure doec before
opening SCO connection.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Add support for HCI_Enhanced_Setup_Synchronous_Connection command

< HCI Command: Enhanced Setup Synchronous Connection (0x01|0x003d) plen 59
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Packet type: 0x0380
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
Retransmission effort: Optimize for link quality (0x02)
> HCI Event: Command Status (0x0f) plen 4
Enhanced Setup Synchronous Connection (0x01|0x003d) ncmd 1
Status: Success (0x00)
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Success (0x00)
Handle: 257
Address: CC:98:8B:92:04:FD (SONY Visual Products Inc.)
Link type: eSCO (0x02)
Transmission interval: 0x0c
Retransmission window: 0x06
RX packet length: 60
TX packet length: 60
Air mode: Transparent (0x03)

Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix using RPA when address has been resolved

When connecting to a device using an RPA if the address has been
resolved by the controller (types 0x02 and 0x03) the identity address
shall be used as the actual RPA in the advertisement won't be visible
to the host.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: use inclusive language in HCI role comments

This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf

Specifically, these terms are replaced:
master -> initiator (for smp) or central (everything else)
slave -> responder (for smp) or peripheral (everything else)

The #define preprocessor terms are unchanged for now to not disturb
dependent APIs.

Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: use inclusive language to describe CPB

This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf

Specifically, these terms are replaced when describing the
connectionless peripheral broadcast feature:
master -> central
slave -> peripheral

Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix spelling mistakes

Fix some spelling mistakes in comments:
udpate ==> update
retreive ==> retrieve
accidentially ==> accidentally
correspondig ==> corresponding
adddress ==> address
estabilish ==> establish
commplete ==> complete
Unkown ==> Unknown
triggerd ==> triggered
transtion ==> transition

Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bluetooth: avoid deadlock between hci_dev->lock and socket lock

Commit eab2404ba798 ("Bluetooth: Add BT_PHY socket option") added a
dependency between socket lock and hci_dev->lock that could lead to
deadlock.

It turns out that hci_conn_get_phy() is not in any way relying on hdev
being immutable during the runtime of this function, neither does it even
look at any of the members of hdev, and as such there is no need to hold
that lock.

This fixes the lockdep splat below:

======================================================
WARNING: possible circular locking dependency detected
5.12.0-rc1-00026-g73d464503354 #10 Not tainted
------------------------------------------------------
bluetoothd/1118 is trying to acquire lock:
ffff8f078383c078 (&hdev->lock){+.+.}-{3:3}, at: hci_conn_get_phy+0x1c/0x150 [bluetooth]

but task is already holding lock:
ffff8f07e831d920 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.}-{0:0}, at: l2cap_sock_getsockopt+0x8b/0x610

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.}-{0:0}:
lock_sock_nested+0x72/0xa0
l2cap_sock_ready_cb+0x18/0x70 [bluetooth]
l2cap_config_rsp+0x27a/0x520 [bluetooth]
l2cap_sig_channel+0x658/0x1330 [bluetooth]
l2cap_recv_frame+0x1ba/0x310 [bluetooth]
hci_rx_work+0x1cc/0x640 [bluetooth]
process_one_work+0x244/0x5f0
worker_thread+0x3c/0x380
kthread+0x13e/0x160
ret_from_fork+0x22/0x30

-> #2 (&chan->lock#2/1){+.+.}-{3:3}:
__mutex_lock+0xa3/0xa10
l2cap_chan_connect+0x33a/0x940 [bluetooth]
l2cap_sock_connect+0x141/0x2a0 [bluetooth]
__sys_connect+0x9b/0xc0
__x64_sys_connect+0x16/0x20
do_syscall_64+0x33/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae

-> #1 (&conn->chan_lock){+.+.}-{3:3}:
__mutex_lock+0xa3/0xa10
l2cap_chan_connect+0x322/0x940 [bluetooth]
l2cap_sock_connect+0x141/0x2a0 [bluetooth]
__sys_connect+0x9b/0xc0
__x64_sys_connect+0x16/0x20
do_syscall_64+0x33/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae

-> #0 (&hdev->lock){+.+.}-{3:3}:
__lock_acquire+0x147a/0x1a50
lock_acquire+0x277/0x3d0
__mutex_lock+0xa3/0xa10
hci_conn_get_phy+0x1c/0x150 [bluetooth]
l2cap_sock_getsockopt+0x5a9/0x610 [bluetooth]
__sys_getsockopt+0xcc/0x200
__x64_sys_getsockopt+0x20/0x30
do_syscall_64+0x33/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae

other info that might help us debug this:

Chain exists of:
&hdev->lock --> &chan->lock#2/1 --> sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP

Possible unsafe locking scenario:

CPU0 CPU1
---- ----
lock(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP);
lock(&chan->lock#2/1);
lock(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP);
lock(&hdev->lock);

*** DEADLOCK ***

1 lock held by bluetoothd/1118:
#0: ffff8f07e831d920 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.}-{0:0}, at: l2cap_sock_getsockopt+0x8b/0x610 [bluetooth]

stack backtrace:
CPU: 3 PID: 1118 Comm: bluetoothd Not tainted 5.12.0-rc1-00026-g73d464503354 #10
Hardware name: LENOVO 20K5S22R00/20K5S22R00, BIOS R0IET38W (1.16 ) 05/31/2017
Call Trace:
dump_stack+0x7f/0xa1
check_noncircular+0x105/0x120
? __lock_acquire+0x147a/0x1a50
__lock_acquire+0x147a/0x1a50
lock_acquire+0x277/0x3d0
? hci_conn_get_phy+0x1c/0x150 [bluetooth]
? __lock_acquire+0x2e1/0x1a50
? lock_is_held_type+0xb4/0x120
? hci_conn_get_phy+0x1c/0x150 [bluetooth]
__mutex_lock+0xa3/0xa10
? hci_conn_get_phy+0x1c/0x150 [bluetooth]
? lock_acquire+0x277/0x3d0
? mark_held_locks+0x49/0x70
? mark_held_locks+0x49/0x70
? hci_conn_get_phy+0x1c/0x150 [bluetooth]
hci_conn_get_phy+0x1c/0x150 [bluetooth]
l2cap_sock_getsockopt+0x5a9/0x610 [bluetooth]
__sys_getsockopt+0xcc/0x200
__x64_sys_getsockopt+0x20/0x30
do_syscall_64+0x33/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fb73df33eee
Code: 48 8b 0d 85 0f 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 49 89 ca b8 37 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 52 0f 0c 00 f7 d8 64 89 01 48
RSP: 002b:00007fffcfbbbf08 EFLAGS: 00000203 ORIG_RAX: 0000000000000037
RAX: ffffffffffffffda RBX: 0000000000000019 RCX: 00007fb73df33eee
RDX: 000000000000000e RSI: 0000000000000112 RDI: 0000000000000018
RBP: 0000000000000000 R08: 00007fffcfbbbf44 R09: 0000000000000000
R10: 00007fffcfbbbf3c R11: 0000000000000203 R12: 0000000000000000
R13: 0000000000000018 R14: 0000000000000000 R15: 0000556fcefc70d0

Fixes: eab2404ba798 ("Bluetooth: Add BT_PHY socket option")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Notify suspend on le conn failed

When suspending, Bluetooth disconnects all connected peers devices. If
an LE connection is started but isn't completed, we will see an LE
Create Connection Cancel instead of an HCI disconnect. This just adds
a check to see if an LE cancel was the last disconnected device and wake
the suspend thread when that is the case.

Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Skip eSCO 2M params when not supported

If a peer device doesn't support eSCO 2M we should skip the params that
use it when setting up sync connection since they will always fail.

Signed-off-by: Yu Liu <yudiliu@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Cancel Inquiry before Create Connection

Many controllers do not allow HCI Create Connection while it is doing
Inquiry. This patch adds Inquiry Cancel before Create Connection in this
case to allow the controller to do Create Connection. User space will be
aware of this Inquiry cancellation and they may issue another discovery
request afterwards.

Sample Command Disallowed response of HCI Create Connection:
< HCI Command: Inquiry (0x01|0x0001) plen 5
Access code: 0x9e8b33 (General Inquiry)
Length: 10.24s (0x08)
Num responses: 0
> HCI Event: Command Status (0x0f) plen 4
Inquiry (0x01|0x0001) ncmd 2
Status: Success (0x00)
< HCI Command: Create Connection (0x01|0x0005) plen 13
Address: XX:XX:XX:XX:XX:XX
Packet type: 0xcc18
Page scan repetition mode: R2 (0x02)
Page scan mode: Mandatory (0x00)
Clock offset: 0x0000
Role switch: Allow slave (0x01)
> HCI Event: Command Status (0x0f) plen 4
Create Connection (0x01|0x0005) ncmd 1
Status: Success (0x00)
> HCI Event: Connect Complete (0x03) plen 11
Status: Command Disallowed (0x0c)
Handle: 65535
Address: XX:XX:XX:XX:XX:XX
Link type: ACL (0x01)
Encryption: Disabled (0x00)

Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Resume advertising after LE connection

When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.

The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.

Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

net: bluetooth: delete duplicated words

Drop repeated words in net/bluetooth/.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bluetooth: Enable/Disable address resolution during le create conn

In this patch if le_create_conn process is started restrict to
disable address resolution and same is disabled during
le_enh_connection_complete

Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add per-instance adv disable/remove

Add functionality to disable and remove advertising instances,
and use that functionality in MGMT add/remove advertising calls.

Currently, advertising is globally-disabled, i.e. all instances are
disabled together, even if hardware offloading is available. This
patch adds functionality to disable and remove individual adv
instances, solving two issues:

1. On new advertisement registration, a global disable was done, and
then only the new instance was enabled. This meant only the newest
instance was actually enabled.

2. On advertisement removal, the structure was removed, but the instance
was never disabled or removed, which is incorrect with hardware offload
support.

Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Shyh-In Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Disconnect if E0 is used for Level 4

E0 is not allowed with Level 4:

BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part C page 1319:

'128-bit equivalent strength for link and encryption keys
required using FIPS approved algorithms (E0 not allowed,
SAFER+ not allowed, and P-192 not allowed; encryption key
not shortened'

SC enabled:

> HCI Event: Read Remote Extended Features (0x23) plen 13
Status: Success (0x00)
Handle: 256
Page: 1/2
Features: 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Secure Simple Pairing (Host Support)
LE Supported (Host)
Secure Connections (Host Support)
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 256
Encryption: Enabled with AES-CCM (0x02)

SC disabled:

> HCI Event: Read Remote Extended Features (0x23) plen 13
Status: Success (0x00)
Handle: 256
Page: 1/2
Features: 0x03 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Secure Simple Pairing (Host Support)
LE Supported (Host)
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 256
Encryption: Enabled with E0 (0x01)
[May 8 20:23] Bluetooth: hci0: Invalid security: expect AES but E0 was used
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 256
Reason: Authentication Failure (0x05)

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Terminate the link if pairing is cancelled

If user decides to cancel the ongoing pairing process (e.g. by clicking
the cancel button on pairing/passkey window), abort any ongoing pairing
and then terminate the link if it was created because of the pair
device action.

Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: centralize default value initialization.

This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.

Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix assuming EIR flags can result in SSP authentication

EIR flags should just hint if SSP may be supported but we shall verify
this with use of the actual features as the SSP bits may be disabled in
the lower layers which would result in legacy authentication to be
used.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: add support to notify using SCO air mode

notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.

Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: During le_conn_timeout disable EXT_ADV

Disabling LE_LEGACY_ADV when LE_EXT_ADV is enabled causes 'command
disallowed . This patch fixes that issue and disables EXT_ADV if
enabled.

Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove adv set for directed advertising

Extended advertising Data is set during bluetooth initialization
by default which causes InvalidHCICommandParameters when setting
Extended advertising parameters.

As per Core Spec 5.2 Vol 2, PART E, Sec 7.8.53, for
advertising_event_property LE_LEGACY_ADV_DIRECT_IND does not
supports advertising data when the advertising set already
contains some, the controller shall return erroc code
'InvalidHCICommandParameters(0x12).

So it is required to remove adv set for handle 0x00. since we use
instance 0 for directed adv.

Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Disable Extended Adv if enabled

Disabling LEGACY_ADV when EXT_ADV is enabled causes
'command disallowed' during DIRECTED_ADV. This Patch fixes this
issue.

Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add BT_PHY socket option

This adds BT_PHY socket option (read-only) which can be used to read
the PHYs in use by the underline connection.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix memory leak in hci_connect_le_scan

In the implementation of hci_connect_le_scan() when conn is added via
hci_conn_add(), if hci_explicit_conn_params_set() fails the allocated
memory for conn is leaked. Use hci_conn_del() to release it.

Fixes: f75113a26008 ("Bluetooth: add hci_connect_le_scan")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Workaround directed advertising bug in Broadcom controllers

It appears that some Broadcom controllers (eg BCM20702A0) reject LE Set
Advertising Parameters command if advertising intervals provided are not
within range for undirected and low duty directed advertising.

Workaround this bug by populating min and max intervals with 'valid'
values.

< HCI Command: LE Set Advertising Parameters (0x08|0x0006) plen 15
Min advertising interval: 0.000 msec (0x0000)
Max advertising interval: 0.000 msec (0x0000)
Type: Connectable directed - ADV_DIRECT_IND (high duty cycle) (0x01)
Own address type: Public (0x00)
Direct address type: Random (0x01)
Direct address: E2:F0:7B:9F:DC:F4 (Static)
Channel map: 37, 38, 39 (0x07)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Parameters (0x08|0x0006) ncmd 1
Status: Invalid HCI Command Parameters (0x12)

Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Sören Beye <linux@hypfer.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use controller sets when available

This makes use of controller sets when using Extended Advertising
feature thus offloading the scheduling to the controller.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add support for LE ping feature

Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.

As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.

Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix regression with minimum encryption key size alignment

When trying to align the minimum encryption key size requirement for
Bluetooth connections, it turns out doing this in a central location in
the HCI connection handling code is not possible.

Original Bluetooth version up to 2.0 used a security model where the
L2CAP service would enforce authentication and encryption. Starting
with Bluetooth 2.1 and Secure Simple Pairing that model has changed into
that the connection initiator is responsible for providing an encrypted
ACL link before any L2CAP communication can happen.

Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and
before devices are causing a regression. The encryption key size check
needs to be moved out of the HCI connection handling into the L2CAP
channel setup.

To achieve this, the current check inside hci_conn_security() has been
moved into l2cap_check_enc_key_size() helper function and then called
from four decisions point inside L2CAP to cover all combinations of
Secure Simple Pairing enabled devices and device using legacy pairing
and legacy service security model.

Fixes: d5bb334a8e17 ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Bluetooth: Align minimum encryption key size for LE and BR/EDR connections

The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

Bluetooth: Implement Set ADV set random address

This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.

Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.

This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.

< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use ext adv for directed adv

This patch does extended advertising for directed advertising
if the controller supportes. Instance 0 is used for directed
advertising.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use selected PHYs in extended connect

Use the selected PHYs by Set PHY Configuration management command
in extended create connection.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use extended LE Connection if supported

This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.

For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.

< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
Filter policy: White list is not used (0x00)
Own address type: Public (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Initiating PHYs: 0x01
Entry 0: LE 1M
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Min connection interval: 50.00 msec (0x0028)
Max connection interval: 70.00 msec (0x0038)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 2
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
Status: Success (0x00)
Handle: 3585
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Connection interval: 67.50 msec (0x0036)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
LE Address: DB:7E:2E:1D:85:E8 (Static)
Flags: 0x00000000
Data length: 27
Name (complete): Designer Mouse
Appearance: Mouse (0x03c2)
Flags: 0x05
LE Limited Discoverable Mode
BR/EDR Not Supported
16-bit Service UUIDs (complete): 1 entry
Human Interface Device (0x1812)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix connection if directed advertising and privacy is used

Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.

This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C

Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #11350 [hci0] 84680.231216
Address: 56:BC:E8:24:11:68 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #11351 [hci0] 84680.246022
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #11352 [hci0] 84680.246417
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #11353 [hci0] 84680.248854
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11354 [hci0] 84680.249466
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #11355 [hci0] 84680.253222
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #11356 [hci0] 84680.458387
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11357 [hci0] 84680.458737
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #11358 [hci0] 84680.469982
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #11359 [hci0] 84680.470444
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #11360 [hci0] 84680.474971
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0 #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4 #11362 [hci0] 84682.551014
LE Create Connection Cancel (0x08|0x000e) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #11363 [hci0] 84682.551074
LE Connection Complete (0x01)
Status: Unknown Connection Identifier (0x02)
Handle: 0
Role: Master (0x00)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Connection interval: 0.00 msec (0x0000)
Connection latency: 0 (0x0000)
Supervision timeout: 0 msec (0x0000)
Master clock accuracy: 0x00

After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #210 [hci0] 667.152459
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #211 [hci0] 667.153613
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #212 [hci0] 667.153704
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #213 [hci0] 667.154584
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #214 [hci0] 667.182619
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #215 [hci0] 667.182704
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #216 [hci0] 667.183599
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #217 [hci0] 667.183645
Address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #218 [hci0] 667.184590
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #219 [hci0] 667.184613
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #220 [hci0] 667.186558
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #221 [hci0] 667.485824
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 0
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13 {0x0002} [hci0] 667.485996
LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
Flags: 0x00000000
Data length: 0

Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Bluetooth: Use bt_dev_err and bt_dev_info when possible

In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix potential memory leak

If command is added to req then it should be freed in case if
hdev is down or HCI_ADVERTISING flag is set.

This introduces a helper in hci_request to purge the cmd_q
to make cmd_q internal to hci_request which is used to fix
the leak.

This also replace accessing of cmd_q in hci_conn with the
new helper.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix using the correct source address type

The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.

This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Rename HCI_BREDR into HCI_PRIMARY

The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add support for limited privacy mode

Introduce a limited privacy mode indicated by value 0x02 to the mgmt
Set Privacy command.

With value 0x02 the kernel will use privacy mode with a resolvable
private address. In case the controller is bondable and discoverable
the identity address will be used.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move memset closer to where it's needed

Minor fix to not do the memset until the variable it clears is
actually used.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Don't treat connection timeout as a failure

When we're doing background scanning and connection attempts it's
possible we timeout trying to connect and go back to scanning again.
The timeout triggers a HCI_LE_Create_Connection_Cancel which will
trigger a Connection Complete with "Unknown Connection Identifier"
error status. Since we go back to scanning this isn't really a failure
and shouldn't be presented as such to user space through mgmt.

The exception to this is if the connection attempt was due to an
explicit request on an L2CAP socket (indicated by
params->explicit_connect being true). Since the socket will get an
error it's consistent to also notify the failure on mgmt in this case.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use continuous scanning when creating LE connections

All LE connections are now triggered through a preceding passive scan
and waiting for a connectable advertising report. This means we've got
the best possible guarantee that the device is within range and should
be able to request the controller to perform continuous scanning. This
way we minimize the risk that we miss out on any advertising packets.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3+

Bluetooth: Move advertising instance management to hci_request.c

This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove conn_unfinished variable from hci_connect_le()

The conn_unfinished variable makes the entire logic of
hci_connect_le() rather confusing. By restructuring and clarifying the
logic we can actually remove the conn_unfinished variable and still
keep the same behavior.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move check for ongoing connect earlier in hci_connect_le()

This helps simplify the logic in further patches (less cleanups to do
in this failure branch).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix specifying role for LE connections

The hci_connect_le_scan() is (as the name implies) a master/central
role API, so it makes no sense in passing a role parameter to it. At
the same time this patch also fixes the direct advertising support for
LE L2CAP sockets where we now call the more appropriate hci_le_connect()
API if slave/peripheral role is desired.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use req_workqueue for explicit connect requests

Since explicit connect requests are also a sub-category of passive
scan updates, run them through the same workqueue as the other passive
scan changes.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add clarifying comment why schedule_work is used

It's not obvious why schedule_work is used instead of queue_work. Add
a comment explaining why.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Make hci_disconnect() behave correctly for all states

There are a few places that don't explicitly check the connection
state before calling hci_disconnect(). To make this API do the right
thing take advantage of the new hci_abort_conn() API and also make
sure to only read the clock offset if we're really connected.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Take advantage of connection abort helpers

Convert the various places mapping connection state to
disconnect/cancel HCI command to use the new hci_abort_conn helper
API.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove unnecessary hci_explicit_connect_lookup function

There's only one user of this helper which can be replaces with a call
to hci_pend_le_action_lookup() and a check for params->explicit_connect.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add hdev helper variable to hci_le_create_connection_cancel

The hci_le_create_connection_cancel() function needs to use the hdev
pointer in many places so add a variable for it to avoid the need to
dereference the hci_conn every time.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use hci_conn_hash_lookup_le() when possible

Use the new hci_conn_hash_lookup_le() API to look up LE connections.
This way we're guaranteed exact matches that also take into account
the address type.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix missing hdev locking for LE scan cleanup

The hci_conn objects don't have a dedicated lock themselves but rely
on the caller to hold the hci_dev lock for most types of access. The
hci_conn_timeout() function has so far sent certain HCI commands based
on the hci_conn state which has been possible without holding the
hci_dev lock.

The recent changes to do LE scanning before connect attempts added
even more operations to hci_conn and hci_dev from hci_conn_timeout,
thereby exposing potential race conditions with the hci_dev and
hci_conn states.

As an example of such a race, here there's a timeout but an
l2cap_sock_connect() call manages to race with the cleanup routine:

[Oct21 08:14] l2cap_chan_timeout: chan ee4b12c0 state BT_CONNECT
[ +0.000004] l2cap_chan_close: chan ee4b12c0 state BT_CONNECT
[ +0.000002] l2cap_chan_del: chan ee4b12c0, conn f3141580, err 111, state BT_CONNECT
[ +0.000002] l2cap_sock_teardown_cb: chan ee4b12c0 state BT_CONNECT
[ +0.000005] l2cap_chan_put: chan ee4b12c0 orig refcnt 4
[ +0.000010] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[ +0.000013] l2cap_chan_put: chan ee4b12c0 orig refcnt 3
[ +0.000063] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[ +0.000049] hci_conn_params_del: addr ee:0d:30:09:53:1f (type 1)
[ +0.000002] hci_chan_list_flush: hcon f53d56e0
[ +0.000001] hci_chan_del: hci0 hcon f53d56e0 chan f4e7ccc0
[ +0.004528] l2cap_sock_create: sock e708fc00
[ +0.000023] l2cap_chan_create: chan ee4b1770
[ +0.000001] l2cap_chan_hold: chan ee4b1770 orig refcnt 1
[ +0.000002] l2cap_sock_init: sk ee4b3390
[ +0.000029] l2cap_sock_bind: sk ee4b3390
[ +0.000010] l2cap_sock_setsockopt: sk ee4b3390
[ +0.000037] l2cap_sock_connect: sk ee4b3390
[ +0.000002] l2cap_chan_connect: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f (type 2) psm 0x00
[ +0.000002] hci_get_route: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f
[ +0.000001] hci_dev_hold: hci0 orig refcnt 8
[ +0.000003] hci_conn_hold: hcon f53d56e0 orig refcnt 0

Above the l2cap_chan_connect() shouldn't have been able to reach the
hci_conn f53d56e0 anymore but since hci_conn_timeout didn't do proper
locking that's not the case. The end result is a reference to hci_conn
that's not in the conn_hash list, resulting in list corruption when
trying to remove it later:

[Oct21 08:15] l2cap_chan_timeout: chan ee4b1770 state BT_CONNECT
[ +0.000004] l2cap_chan_close: chan ee4b1770 state BT_CONNECT
[ +0.000003] l2cap_chan_del: chan ee4b1770, conn f3141580, err 111, state BT_CONNECT
[ +0.000001] l2cap_sock_teardown_cb: chan ee4b1770 state BT_CONNECT
[ +0.000005] l2cap_chan_put: chan ee4b1770 orig refcnt 4
[ +0.000002] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[ +0.000015] l2cap_chan_put: chan ee4b1770 orig refcnt 3
[ +0.000038] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[ +0.000003] hci_chan_list_flush: hcon f53d56e0
[ +0.000002] hci_conn_hash_del: hci0 hcon f53d56e0
[ +0.000001] ------------[ cut here ]------------
[ +0.000461] WARNING: CPU: 0 PID: 1782 at lib/list_debug.c:56 __list_del_entry+0x3f/0x71()
[ +0.000839] list_del corruption, f53d56e0->prev is LIST_POISON2 (00000200)

The necessary fix is unfortunately more complicated than just adding
hci_dev_lock/unlock calls to the hci_conn_timeout() call path.
Particularly, the hci_conn_del() API, which expects the hci_dev lock to
be held, performs a cancel_delayed_work_sync(&hcon->disc_work) which
would lead to a deadlock if the hci_conn_timeout() call path tries to
acquire the same lock.

This patch solves the problem by deferring the cleanup work to a
separate work callback. To protect against the hci_dev or hci_conn
going away meanwhile temporary references are taken with the help of
hci_dev_hold() and hci_conn_get().

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3

Bluetooth: Fix initializing conn_params in scan phase

This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup

After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix LE reconnection logic

We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.

To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix reference counting for LE-scan based connections

The code should never directly call hci_conn_hash_del since many
cleanup & reference counting updates would be lost. Normally
hci_conn_del is the right thing to do, but in the case of a connection
doing LE scanning this could cause a deadlock due to doing a
cancel_delayed_work_sync() on the same work callback that we were
called from.

Connections in the LE scanning state actually need very little cleanup
- just a small subset of hci_conn_del. To solve the issue, refactor
out these essential pieces into a new hci_conn_cleanup() function and
call that from the two necessary places.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix double scan updates

When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.

This patch makes sure that unnecessary scan disable/enable commands
are not issued.

When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.

hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.

When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: timeout handling in new connect procedure

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch makes sure that when new procedure is in use, and we're stuck
in scan phase because no advertisement was received and timeout happened,
or app decided to close socket, scan whitelist gets properly cleaned up.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: advertisement handling in new connect procedure

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This path makes sure that after advertisement is received from device that
we try to connect to, it is properly handled in check_pending_le_conn and
trigger connect attempt.

It also modifies hci_le_connect to make sure that connect attempt will be
properly continued.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: add hci_connect_le_scan

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch adds hci_connect_le_scan with dependencies, new method that
will be used to connect to remote LE devices. Instead of just sending
connect request, it adds a device to whitelist. Later patches will make
use of this whitelist to send conenct request when advertisement is
received, and properly handle timeouts.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: add hci_lookup_le_connect

This patch adds hci_lookup_le_connect method, that will be used to check
wether outgoing le connection attempt is in progress.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix encryption key size handling for LTKs

The encryption key size for LTKs is supposed to be applied only at the
moment of encryption. When generating a Link Key (using LE SC) from
the LTK the full non-shortened value should be used. This patch
modifies the code to always keep the full value around and only apply
the key size when passing the value to HCI.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Introduce hci_dev_clear_flag helper macro

Instead of manually coding clear_bit on hdev->dev_flags all the time,
use hci_dev_clear_flag helper macro.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Introduce hci_dev_set_flag helper macro

Instead of manually coding set_bit on hdev->dev_flags all the time,
use hci_dev_set_flag helper macro.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Introduce hci_dev_test_flag helper macro

Instead of manually coding test_bit on hdev->dev_flags all the time,
use hci_dev_test_flag helper macro.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Convert disconn_cfm to be triggered through hci_cb

This patch moves all the disconn_cfm callbacks to be based on the hci_cb
list. This means making l2cap_disconn_cfm private to l2cap_core.c and
sco_conn_cb private to sco.c respectively. Since the hci_conn type
filtering isn't done any more on the wrapper level the callbacks
themselves need to check that they were passed a relevant type of
connection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Convert connect_cfm to be triggered through hci_cb

This patch moves all the connect_cfm callbacks to be based on the hci_cb
list. This means making l2cap_connect_cfm private to l2cap_core.c and
sco_connect_cb private to sco.c respectively. Since the hci_conn type
filtering isn't done any more on the wrapper level the callbacks
themselves need to check that they were passed a relevant type of
connection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Improve error handling in connect acl

With this patch -EOPNOTSUPP will be returned by hci_connect_acl for LE
only controllers. If it is dual device with disabled BREDR -ECONNREFUSED
will be returned

Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Do not allow LE connection if LE is not enabled

Kernel gives possibility to enable/disable LE host support.
There is flag HCI_LE_ENABLED which is set when this support is enabled
and some parts of the code checks this flag e.g. SMP
However it is still possible to make LE connection if LE Host support is
disabled, what might be confused for remote device.
This patch makes sure that kernel will not send HCI LE Create Connection
if LE HOST support is not enabled.

Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Remove unused function

Remove the function hci_conn_change_link_key() that is not used anywhere.

This was partially found by using a static code analysis program called
cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add opcode parameter to hci_req_complete_t callback

When hci_req_run() calls its provided complete function and one of the
HCI commands in the sequence fails, then provide the opcode of failing
command. In case of success HCI_OP_NOP is provided since all commands
completed.

This patch fixes the prototype of hci_req_complete_t and all its users.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Create debugfs directory for each connection handle

For every internal representation of a Bluetooth connection which is
identified by hci_conn, create a debugfs directory with the handle
number as directory name.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Split hci_request helpers to hci_request.[ch]

None of the hci_request related things in net/bluetooth/hci_core.h are
needed anywhere outside of the core bluetooth module. This patch creates
a new net/bluetooth/hci_request.c file with its corresponding h-file and
moves the functionality there from hci_core.c and hci_core.h.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix generation of non-resolvable private addresses

When the host decides to use a non-resolvable private address, it
must ensure that this generated address does not match the public
address of the controller. Add an extra check to ensure this required
behavior.

In addition rename the variable from urpa to nrpa and fix all of the
comments in the code that use the term unresolvable instead of the
term non-resolvable as used in the Bluetooth specification.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix initializing hci_conn RSSI to invalid value

When we create the hci_conn object we should properly initialize the
RSSI to HCI_RSSI_INVALID.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix check for direct advertising

These days we allow simultaneous LE scanning and advertising. Checking
for whether advertising is enabled or not is therefore not a reliable
way to determine whether directed advertising was used to trigger the
connection creation. The appropriate place to check (instead of the hdev
context) is the connection role that's stored in the hci_conn. This
patch fixes such a check in le_conn_timeout() which could otherwise lead
to incorrect HCI commands being sent.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16.x

Bluetooth: Fix LE connection timeout deadlock

The le_conn_timeout() may call hci_le_conn_failed() which in turn may
call hci_conn_del(). Trying to use the _sync variant for cancelling the
conn timeout from hci_conn_del() could therefore result in a deadlock.
This patch converts hci_conn_del() to use the non-sync variant so the
deadlock is not possible.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16.x

Bluetooth: fix shadow warning in hci_disconnect()

use clkoff_cp for hci_cp_read_clock_offset instead of cp
(already defined above).

Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Defer connection-parameter removal when unpairing

Systematically removing the LE connection parameters and autoconnect
action is inconvenient for rebonding without disconnecting from
userland (i.e. unpairing followed by repairing without
disconnecting). The parameters will be lost after unparing and
userland needs to take care of book-keeping them and re-adding them.

This patch allows userland to forget about parameter management when
rebonding without disconnecting. It defers clearing the connection
parameters when unparing without disconnecting, giving a chance of
keeping the parameters if a repairing happens before the connection is
closed.

Signed-off-by: Alfonso Acosta <fons@spotify.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Rename sco_param_wideband table to esco_param_msbc

The sco_param_wideband table represents the eSCO parameters for
specifically mSBC encoding. This patch renames the table to the more
descriptive esco_param_msbc name.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add retransmission effort into SCO parameter table

It is expected that new parameter combinations will have the
retransmission effort value different between some entries (mainly
because of the new S4 configuration added by HFP 1.7), so it makes sense
to move it into the table instead of having it hard coded based on the
selected SCO_AIRMODE_*.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix reason code used for rejecting SCO connections

The core specification defines valid values for the
HCI_Reject_Synchronous_Connection_Request command to be 0x0D-0x0F. So
far the code has been using HCI_ERROR_REMOTE_USER_TERM (0x13) which is
not a valid value and is therefore being rejected by some controllers:

> HCI Event: Connect Request (0x04) plen 10
bdaddr 40:6F:2A:6A:E5:E0 class 0x000000 type eSCO
< HCI Command: Reject Synchronous Connection (0x01|0x002a) plen 7
bdaddr 40:6F:2A:6A:E5:E0 reason 0x13
Reason: Remote User Terminated Connection
> HCI Event: Command Status (0x0f) plen 4
Reject Synchronous Connection (0x01|0x002a) status 0x12 ncmd 1
Error: Invalid HCI Command Parameters

This patch introduces a new define for a value from the valid range
(0x0d == Connection Rejected Due To Limited Resources) and uses it
instead for rejecting incoming connections.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Check for SCO type before setting retransmission effort

SCO connection cannot be setup to devices that do not support retransmission.
Patch based on http://permalink.gmane.org/gmane.linux.bluez.kernel/7779 and
adapted for this kernel version.

Code changed to check SCO/eSCO type before setting retransmission effort
and max. latency. The purpose of the patch is to support older devices not
capable of eSCO.

Tested on Blackberry 655+ headset which does not support retransmission.
Credits go to Alexander Sommerhuber.

Signed-off-by: Bernhard Thaler <bernhard.thaler@r-it.at>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move clock offset reading into hci_disconnect()

To give all hci_disconnect() users the advantage of getting the clock
offset read automatically this patch moves the necessary code from
hci_conn_timeout() into hci_disconnect(). This way we pretty much always
update the clock offset when disconnecting.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Update hci_disconnect() to return an error value

We'll soon use hci_disconnect() from places that are interested to know
whether the hci_send_cmd() really succeeded or not. This patch updates
hci_disconnect() to pass on any error returned from hci_send_cmd().

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove hci_conn_hold/drop from hci_chan

We can't have hci_chan contribute to the "active" reference counting of
the hci_conn since otherwise the connection would never get dropped when
there are no more users (since hci_chan would be counted as a user).
This patch removes hold() when creating the hci_chan and drop() when
destroying it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Ignore incoming data after initiating disconnection

When hci_chan_del is called the disconnection routines get scheduled
through a workqueue. If there's any incoming ACL data before the
routines get executed there's a chance that a new hci_chan is created
and the disconnection never happens. This patch adds a new hci_conn flag
to indicate that we're in the process of driving the connection down. We
set the flag in hci_chan_del and check for it in hci_chan_create so that
no new channels are created for the same connection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Set disc_timeout to 0 when calling hci_chan_del

The hci_chan_del() function is used in scenarios where we've decided we
want to get rid of the underlying baseband link. It makes therefore
sense to force the disc_timeout to 0 so that the disconnection routines
are immediately scheduled.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix hci_conn reference counting with hci_chan

The hci_chan_del() function was doing a hci_conn_drop() but there was no
matching hci_conn_hold() in the hci_chan_create() function. Furthermore,
as the hci_chan struct holds a pointer to the hci_conn there should be
proper use of hci_conn_get/put. This patch fixes both issues so that
hci_chan does correct reference counting of the hci_conn object.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix using hci_conn_get() for hci_conn pointers

Wherever we keep hci_conn pointers around we should be using
hci_conn_get/put to ensure that they stay valid. This patch fixes
all places violating against the principle currently.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix hci_conn reference counting for auto-connections

Recently the LE passive scanning and auto-connections feature was
introduced. It uses the hci_connect_le() API which returns a hci_conn
along with a reference count to that object. All previous users would
tie this returned reference to some existing object, such as an L2CAP
channel, and there'd be no leaked references this way. For
auto-connections however the reference was returned but not stored
anywhere, leaving established connections with one higher reference
count than they should have.

Instead of playing special tricks with hci_conn_hold/drop this patch
associates the returned reference from hci_connect_le() with the object
that in practice does own this reference, i.e. the hci_conn_params
struct that caused us to initiate a connection in the first place. Once
the connection is established or fails to establish this reference is
removed appropriately.

One extra thing needed is to call hci_pend_le_actions_clear() before
calling hci_conn_hash_flush() so that the reference is cleared before
the hci_conn objects are fully removed.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Prefer sizeof(*ptr) when allocating memory

It's safer practice to use sizeof(*ptr) instead of sizeof(ptr_type) when
allocating memory in case the type changes. This also fixes the
following style of warnings from static analyzers:

CHECK: Prefer kzalloc(sizeof(*ie)...) over kzalloc(sizeof(struct inquiry_entry)...)
+ ie = kzalloc(sizeof(struct inquiry_entry), GFP_KERNEL);

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use EOPNOTSUPP instead of ENOTSUPP

The EOPNOTSUPP and ENOTSUPP errors are very similar in meaning, but
ENOTSUPP is a fairly new addition to POSIX. Not all libc versions know
about the value the kernel uses for ENOTSUPP so it's better to use
EOPNOTSUPP to ensure understandable error messages.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Introduce a flag to track who really initiates authentication

Even though our side requests authentication, the original action that
caused it may be remotely triggered, such as an incoming L2CAP or RFCOMM
connect request. To track this information introduce a new hci_conn flag
called HCI_CONN_AUTH_INITIATOR.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Pass initiator/acceptor information to hci_conn_security()

We're interested in whether an authentication request is because of a
remote or local action. So far hci_conn_security() has been used both
for incoming and outgoing actions (e.g. RFCOMM or L2CAP connect
requests) so without some modifications it cannot know which peer is
responsible for requesting authentication.

This patch adds a new "bool initiator" parameter to hci_conn_security()
to indicate which side is responsible for the request and updates the
current users to pass this information correspondingly.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add a role parameter to hci_conn_add()

We need to be able to track slave vs master LE connections in
hci_conn_hash, and to be able to do that we need to know the role of the
connection by the time hci_conn_add_has() is called. This means in
practice the hci_conn_add() call that creates the hci_conn_object.

This patch adds a new role parameter to hci_conn_add() function to give
the object its initial role value, and updates the callers to pass the
appropriate role to it. Since the function now takes care of
initializing both conn->role and conn->out values we can remove some
other unnecessary assignments.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use explicit role instead of a bool in function parameters

To make the code more understandable it makes sense to use the new HCI
defines for connection role instead of a "bool master" parameter. This
makes it immediately clear when looking at the function calls what the
last parameter is describing.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Convert HCI_CONN_MASTER flag to a conn->role variable

Having a dedicated u8 role variable in the hci_conn struct greatly
simplifies tracking of the role, since this is the native way that it's
represented on the HCI level.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix advertising and active scanning co-existence

Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.

This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Stop advertising always before initiating a connection

Most controllers do not support advertising while initiating an LE
connection. We also have to first disable current advertising if the
initiation is going to happen through direct advertising. Therefore,
simply stop advertising as the first thing when starting to issue
commands to establish an LE connection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use real advertising state to random address update decision

Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Pass desired connection role to hci_connect_le()

If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove auth_type parameter from hci_connect_le()

The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use lower timeout for LE auto-connections

When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Make hci_le_conn_update return the store hint

The caller of hci_le_conn_update is directly interested in knowing what
the best value is for the store_hint parameter of the corresponding
mgmt event. Since hci_le_conn_update knows whether there were stored
parameters that were updated or not we can have it return an initial
store_hint value to the caller.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Provide defaults for LE connection latency and timeout

Store the connection latency and supervision timeout default values
with all the other controller defaults. And when needed use them
for new connections.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Use LE connection parameters if known

When the LE connection parameters for connection latency and
supervision timeout are known, then use then. If they are not
know fallback to defaults.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Store latency and supervision timeout in connection params

When the slave updates the connection parameters, store also the
connection latency and supervision timeout information in the
internal list of connection parameters for known devices.

Having these values available allowes the auto-connection
procedure to use the correct values from the beginning without
having to request an update on every connection establishment.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Restrict access for raw-only controllers

Bluetooth controllers that are marked for raw-only usage can only be
used with user channel access. Any other operation should be rejected.

This simplifies the whole raw-only support since it now depends on
the fact that the controller is marked with HCI_QUIRK_RAW_DEVICE and
runtime raw access is restricted to user channel operation.

The kernel internal processing of HCI commands and events is designed
around the case that either the kernel has full control over the device
or that the device is driven from userspace. This now makes a clear
distinction between these two possible operation modes.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Send HCI_Read_Clock_Offset before disconnecting

When the connection is in master role and it is going to be
disconnected based on the disconnection timeout, then send
the HCI_Read_Clock_Offset command in an attempt to update the
clock offset value in the inquiry cache.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Remove unneeded hci_conn_disconnect abstraction

The abstraction of disconnect operation via hci_conn_disconnect is not
needed and it does not add any readability. Handle the difference of
AMP physical channels and BR/EDR/LE connection in the timeout callback.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Remove reason parameter from hci_amp_disconn function

The hci_amp_disconn function is a local function and there is no
need for a reason parameter. That one can be retrieved from the
hci_conn object easily.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Convert hci_conn->link_mode into flags

Since the link_mode member of the hci_conn struct is a bit field and we
already have a flags member as well it makes sense to merge these two
together. This patch moves all used link_mode bits into corresponding
flags. To keep backwards compatibility with user space we still need to
provide a get_link_mode() helper function for the ioctl's that expect a
link_mode style value.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix for ACL disconnect when pairing fails

When pairing fails hci_conn refcnt drops below zero. This cause that
ACL link is not disconnected when disconnect timeout fires.

Probably this is because l2cap_conn_del calls l2cap_chan_del for each
channel, and inside l2cap_chan_del conn is dropped. After that loop
hci_chan_del is called which also drops conn.

Anyway, as it is desrcibed in hci_core.h, it is known that refcnt
drops below 0 sometimes and it should be fine. If so, let disconnect
link when hci_conn_timeout fires and refcnt is 0 or below. This patch
does it.

This affects PTS test SM_TC_JW_BV_05_C

Logs from scenario:

[69713.706227] [6515] pair_device:
[69713.706230] [6515] hci_conn_add: hci0 dst 00:1b:dc:06:06:22
[69713.706233] [6515] hci_dev_hold: hci0 orig refcnt 8
[69713.706235] [6515] hci_conn_init_sysfs: conn ffff88021f65a000
[69713.706239] [6515] hci_req_add_ev: hci0 opcode 0x200d plen 25
[69713.706242] [6515] hci_prepare_cmd: skb len 28
[69713.706243] [6515] hci_req_run: length 1
[69713.706248] [6515] hci_conn_hold: hcon ffff88021f65a000 orig refcnt 0
[69713.706251] [6515] hci_dev_put: hci0 orig refcnt 9
[69713.706281] [8909] hci_cmd_work: hci0 cmd_cnt 1 cmd queued 1
[69713.706288] [8909] hci_send_frame: hci0 type 1 len 28
[69713.706290] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 28
[69713.706316] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.706382] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.711664] [8909] hci_rx_work: hci0
[69713.711668] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 6
[69713.711680] [8909] hci_rx_work: hci0 Event packet
[69713.711683] [8909] hci_cs_le_create_conn: hci0 status 0x00
[69713.711685] [8909] hci_sent_cmd_data: hci0 opcode 0x200d
[69713.711688] [8909] hci_req_cmd_complete: opcode 0x200d status 0x00
[69713.711690] [8909] hci_sent_cmd_data: hci0 opcode 0x200d
[69713.711695] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.711744] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.818875] [8909] hci_rx_work: hci0
[69713.818889] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 21
[69713.818913] [8909] hci_rx_work: hci0 Event packet
[69713.818917] [8909] hci_le_conn_complete_evt: hci0 status 0x00
[69713.818922] [8909] hci_send_to_control: len 19
[69713.818927] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.818938] [8909] hci_conn_add_sysfs: conn ffff88021f65a000
[69713.818975] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
[69713.818981] [6515] hci_sock_recvmsg: sock ffff88005e75a080, sk ffff88010323ac00
...
[69713.819021] [8909] hci_dev_hold: hci0 orig refcnt 10
[69713.819025] [8909] l2cap_connect_cfm: hcon ffff88021f65a000 bdaddr 00:1b:dc:06:06:22 status 0
[69713.819028] [8909] hci_chan_create: hci0 hcon ffff88021f65a000
[69713.819031] [8909] l2cap_conn_add: hcon ffff88021f65a000 conn ffff880221005c00 hchan ffff88020d60b1c0
[69713.819034] [8909] l2cap_conn_ready: conn ffff880221005c00
[69713.819036] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.819037] [8909] smp_conn_security: conn ffff880221005c00 hcon ffff88021f65a000 level 0x02
[69713.819039] [8909] smp_chan_create:
[69713.819041] [8909] hci_conn_hold: hcon ffff88021f65a000 orig refcnt 1
[69713.819043] [8909] smp_send_cmd: code 0x01
[69713.819045] [8909] hci_send_acl: hci0 chan ffff88020d60b1c0 flags 0x0000
[69713.819046] [5949] hci_sock_recvmsg: sock ffff8800941a9900, sk ffff88012bf4e800
[69713.819049] [8909] hci_queue_acl: hci0 nonfrag skb ffff88005157c100 len 15
[69713.819055] [5949] hci_sock_recvmsg: sock ffff8800941a9900, sk ffff88012bf4e800
[69713.819057] [8909] l2cap_le_conn_ready:
[69713.819064] [8909] l2cap_chan_create: chan ffff88005ede2c00
[69713.819066] [8909] l2cap_chan_hold: chan ffff88005ede2c00 orig refcnt 1
[69713.819069] [8909] l2cap_sock_init: sk ffff88005ede5800
[69713.819072] [8909] bt_accept_enqueue: parent ffff880160356000, sk ffff88005ede5800
[69713.819074] [8909] __l2cap_chan_add: conn ffff880221005c00, psm 0x00, dcid 0x0004
[69713.819076] [8909] l2cap_chan_hold: chan ffff88005ede2c00 orig refcnt 2
[69713.819078] [8909] hci_conn_hold: hcon ffff88021f65a000 orig refcnt 2
[69713.819080] [8909] smp_conn_security: conn ffff880221005c00 hcon ffff88021f65a000 level 0x01
[69713.819082] [8909] l2cap_sock_ready_cb: sk ffff88005ede5800, parent ffff880160356000
[69713.819086] [8909] le_pairing_complete_cb: status 0
[69713.819091] [8909] hci_tx_work: hci0 acl 10 sco 8 le 0
[69713.819093] [8909] hci_sched_acl: hci0
[69713.819094] [8909] hci_sched_sco: hci0
[69713.819096] [8909] hci_sched_esco: hci0
[69713.819098] [8909] hci_sched_le: hci0
[69713.819099] [8909] hci_chan_sent: hci0
[69713.819101] [8909] hci_chan_sent: chan ffff88020d60b1c0 quote 10
[69713.819104] [8909] hci_sched_le: chan ffff88020d60b1c0 skb ffff88005157c100 len 15 priority 7
[69713.819106] [8909] hci_send_frame: hci0 type 2 len 15
[69713.819108] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 15
[69713.819119] [8909] hci_chan_sent: hci0
[69713.819121] [8909] hci_prio_recalculate: hci0
[69713.819123] [8909] process_pending_rx:
[69713.819226] [6450] hci_sock_recvmsg: sock ffff88005e758780, sk ffff88010323d400
...
[69713.822022] [6450] l2cap_sock_accept: sk ffff880160356000 timeo 0
[69713.822024] [6450] bt_accept_dequeue: parent ffff880160356000
[69713.822026] [6450] bt_accept_unlink: sk ffff88005ede5800 state 1
[69713.822028] [6450] l2cap_sock_accept: new socket ffff88005ede5800
[69713.822368] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.822375] [6450] l2cap_sock_getsockopt: sk ffff88005ede5800
[69713.822383] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.822414] [6450] bt_sock_poll: sock ffff8800941ab700, sk ffff88005ede5800
...
[69713.823255] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.823259] [6450] l2cap_sock_getsockopt: sk ffff88005ede5800
[69713.824322] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.824330] [6450] l2cap_sock_getsockopt: sk ffff88005ede5800
[69713.825029] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
...
[69713.825187] [6450] l2cap_sock_sendmsg: sock ffff8800941ab700, sk ffff88005ede5800
[69713.825189] [6450] bt_sock_wait_ready: sk ffff88005ede5800
[69713.825192] [6450] l2cap_create_basic_pdu: chan ffff88005ede2c00 len 3
[69713.825196] [6450] l2cap_do_send: chan ffff88005ede2c00, skb ffff880160b0b500 len 7 priority 0
[69713.825199] [6450] hci_send_acl: hci0 chan ffff88020d60b1c0 flags 0x0000
[69713.825201] [6450] hci_queue_acl: hci0 nonfrag skb ffff880160b0b500 len 11
[69713.825210] [8909] hci_tx_work: hci0 acl 9 sco 8 le 0
[69713.825213] [8909] hci_sched_acl: hci0
[69713.825214] [8909] hci_sched_sco: hci0
[69713.825216] [8909] hci_sched_esco: hci0
[69713.825217] [8909] hci_sched_le: hci0
[69713.825219] [8909] hci_chan_sent: hci0
[69713.825221] [8909] hci_chan_sent: chan ffff88020d60b1c0 quote 9
[69713.825223] [8909] hci_sched_le: chan ffff88020d60b1c0 skb ffff880160b0b500 len 11 priority 0
[69713.825225] [8909] hci_send_frame: hci0 type 2 len 11
[69713.825227] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 11
[69713.825242] [8909] hci_chan_sent: hci0
[69713.825253] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.825253] [8909] hci_prio_recalculate: hci0
[69713.825292] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.825768] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
...
[69713.866902] [8909] hci_rx_work: hci0
[69713.866921] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 7
[69713.866928] [8909] hci_rx_work: hci0 Event packet
[69713.866931] [8909] hci_num_comp_pkts_evt: hci0 num_hndl 1
[69713.866937] [8909] hci_tx_work: hci0 acl 9 sco 8 le 0
[69713.866939] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.866940] [8909] hci_sched_acl: hci0
...
[69713.866944] [8909] hci_sched_le: hci0
[69713.866953] [8909] hci_chan_sent: hci0
[69713.866997] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.867840] [28074] hci_rx_work: hci0
[69713.867844] [28074] hci_send_to_monitor: hdev ffff88021f0c7000 len 7
[69713.867850] [28074] hci_rx_work: hci0 Event packet
[69713.867853] [28074] hci_num_comp_pkts_evt: hci0 num_hndl 1
[69713.867857] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.867858] [28074] hci_tx_work: hci0 acl 10 sco 8 le 0
[69713.867860] [28074] hci_sched_acl: hci0
[69713.867861] [28074] hci_sched_sco: hci0
[69713.867862] [28074] hci_sched_esco: hci0
[69713.867863] [28074] hci_sched_le: hci0
[69713.867865] [28074] hci_chan_sent: hci0
[69713.867888] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69714.145661] [8909] hci_rx_work: hci0
[69714.145666] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 10
[69714.145676] [8909] hci_rx_work: hci0 ACL data packet
[69714.145679] [8909] hci_acldata_packet: hci0 len 6 handle 0x002d flags 0x0002
[69714.145681] [8909] hci_conn_enter_active_mode: hcon ffff88021f65a000 mode 0
[69714.145683] [8909] l2cap_recv_acldata: conn ffff880221005c00 len 6 flags 0x2
[69714.145693] [8909] l2cap_recv_frame: len 2, cid 0x0006
[69714.145696] [8909] hci_send_to_control: len 14
[69714.145710] [8909] smp_chan_destroy:
[69714.145713] [8909] pairing_complete: status 3
[69714.145714] [8909] cmd_complete: sock ffff88010323ac00
[69714.145717] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 3
[69714.145719] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69714.145720] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
[69714.145722] [6515] hci_sock_recvmsg: sock ffff88005e75a080, sk ffff88010323ac00
[69714.145724] [6450] bt_sock_poll: sock ffff8801db6b4f00, sk ffff880160351c00
...
[69714.145735] [6515] hci_sock_recvmsg: sock ffff88005e75a080, sk ffff88010323ac00
[69714.145737] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 2
[69714.145739] [8909] l2cap_conn_del: hcon ffff88021f65a000 conn ffff880221005c00, err 13
[69714.145740] [6450] bt_sock_poll: sock ffff8801db6b5400, sk ffff88021e775000
[69714.145743] [6450] bt_sock_poll: sock ffff8801db6b5e00, sk ffff880160356000
[69714.145744] [8909] l2cap_chan_hold: chan ffff88005ede2c00 orig refcnt 3
[69714.145746] [6450] bt_sock_poll: sock ffff8800941ab700, sk ffff88005ede5800
[69714.145748] [8909] l2cap_chan_del: chan ffff88005ede2c00, conn ffff880221005c00, err 13
[69714.145749] [8909] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 4
[69714.145751] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 1
[69714.145754] [6450] bt_sock_poll: sock ffff8800941ab700, sk ffff88005ede5800
[69714.145756] [8909] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 3
[69714.145759] [8909] hci_chan_del: hci0 hcon ffff88021f65a000 chan ffff88020d60b1c0
[69714.145766] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69714.145787] [6515] hci_sock_release: sock ffff88005e75a080 sk ffff88010323ac00
[69714.146002] [6450] hci_sock_recvmsg: sock ffff88005e758780, sk ffff88010323d400
[69714.150795] [6450] l2cap_sock_release: sock ffff8800941ab700, sk ffff88005ede5800
[69714.150799] [6450] l2cap_sock_shutdown: sock ffff8800941ab700, sk ffff88005ede5800
[69714.150802] [6450] l2cap_chan_close: chan ffff88005ede2c00 state BT_CLOSED
[69714.150805] [6450] l2cap_sock_kill: sk ffff88005ede5800 state BT_CLOSED
[69714.150806] [6450] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 2
[69714.150808] [6450] l2cap_sock_destruct: sk ffff88005ede5800
[69714.150809] [6450] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 1
[69714.150811] [6450] l2cap_chan_destroy: chan ffff88005ede2c00
[69714.150970] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
...
[69714.151991] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 0
[69716.150339] [8909] hci_conn_timeout: hcon ffff88021f65a000 state BT_CONNECTED, refcnt -1

Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix check for connection encryption

The conn->link_key variable tracks the type of link key in use. It is
set whenever we respond to a link key request as well as when we get a
link key notification event.

These two events do not however always guarantee that encryption is
enabled: getting a link key request and responding to it may only mean
that the remote side has requested authentication but not encryption. On
the other hand, the encrypt change event is a certain guarantee that
encryption is enabled. The real encryption state is already tracked in
the conn->link_mode variable through the HCI_LM_ENCRYPT bit.

This patch fixes a check for encryption in the hci_conn_auth function to
use the proper conn->link_mode value and thereby eliminates the chance
of a false positive result.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Bluetooth: Fix incorrectly overriding conn->src_type

The src_type member of struct hci_conn should always reflect the address
type of the src_member. It should never be overridden. There is already
code in place in the command status handler of HCI_LE_Create_Connection
to copy the right initiator address into conn->init_addr_type.

Without this patch, if privacy is enabled, we will send the wrong
address type in the SMP identity address information PDU (it'll e.g.
contain our public address but a random address type).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Bluetooth: Make SMP context private to smp.c

There are no users of the smp_chan struct outside of smp.c so move it
away from smp.h. The addition of the l2cap.h include to hci_core.c,
hci_conn.c and mgmt.c is something that should have been there already
previously to avoid warnings of undeclared struct l2cap_conn, but the
compiler warning was apparently shadowed away by the mention of
l2cap_conn in the struct smp_chan definition.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Store max TX power level for connection

This patch adds support to store local maximum TX power level for
connection when reply for HCI_Read_Transmit_Power_Level is received.

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Store TX power level for connection

This patch adds support to store local TX power level for connection
when reply for HCI_Read_Transmit_Power_Level is received.

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix redundant encryption request for reauthentication

When we're performing reauthentication (in order to elevate the
security level from an unauthenticated key to an authenticated one) we
do not need to issue any encryption command once authentication
completes. Since the trigger for the encryption HCI command is the
ENCRYPT_PEND flag this flag should not be set in this scenario.
Instead, the REAUTH_PEND flag takes care of all necessary steps for
reauthentication.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Bluetooth: Add directed advertising support through connect()

When we're in peripheral mode (HCI_ADVERTISING flag is set) the most
natural mapping of connect() is to perform directed advertising to the
peer device.

This patch does the necessary changes to enable directed advertising and
keeps the hci_conn state as BT_CONNECT in a similar way as is done for
central or BR/EDR connection initiation.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move local identity address setting to a central place

Any time hci_conn_add is used for an LE connection we need to ensure
that the local identity address is correctly described in the src and
src_type variables. This patch moves setting these values directly into
hci_conn_add so that callers don't have to duplicate the effort
themselves.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Enforce strict Secure Connections Only mode security

In Secure Connections Only mode, it is required that Secure Connections
is used for pairing and that the link key is encrypted with AES-CCM using
a P-256 authenticated combination key. If this is not the case, then new
connection shall be refused or existing connections shall be dropped.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove unnecessary stop_scan_complete function

The stop_scan_complete function was used as an intermediate step before
doing the actual connection creation. Since we're using hci_request
there's no reason to have this extra function around, i.e. we can simply
put both HCI commands into the same request.

The single task that the intermediate function had, i.e. indicating
discovery as stopped is now taken care of by a new
HCI_LE_SCAN_INTERRUPTED flag which allows us to do the discovery state
update when the stop scan command completes.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix trying to disable scanning twice

The discovery process has a timer for disabling scanning, however
scanning might be disabled through other means too like the auto-connect
process. We should therefore ensure that the timer is never active
after sending a HCI command to disable scanning.

There was some existing code in stop_scan_complete trying to avoid the
timer when a connect request interrupts a discovery procedure, but the
other way around was not covered. This patch covers both scenarios by
canceling the timer as soon as we get a successful command complete for
the disabling HCI command.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add timeout for LE connection attempts

LE connection attempts do not have a controller side timeout in the same
way as BR/EDR has (in form of the page timeout). Since we always do
scanning before initiating connections the attempts are always expected
to succeed in some reasonable time.

This patch adds a timer which forces a cancellation of the connection
attempt within 20 seconds if it has not been successful by then. This
way we e.g. ensure that mgmt_pair_device times out eventually and gives
an error response.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix updating connection state to BT_CONNECT too early

We shouldn't update the hci_conn state to BT_CONNECT until the moment
that we're ready to send the initiating HCI command for it. If the
connection has the BT_CONNECT state too early the code responsible for
updating the local random address may incorrectly think there's a
pending connection in progress and refuse to update the address.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use __le64 type for LE random numbers

The random numbers in Bluetooth Low Energy are 64-bit numbers and should
also be little endian since the HCI specification is little endian.

Change the whole Low Energy pairing to use __le64 instead of a byte
array.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Introduce LE auto connection infrastructure

This patch introduces the LE auto connection infrastructure which
will be used to implement the LE auto connection options.

In summary, the auto connection mechanism works as follows: Once the
first pending LE connection is created, the background scanning is
started. When the target device is found in range, the kernel
autonomously starts the connection attempt. If connection is
established successfully, that pending LE connection is deleted and
the background is stopped.

To achieve that, this patch introduces the hci_update_background_scan()
which controls the background scanning state. This function starts or
stops the background scanning based on the hdev->pend_le_conns list. If
there is no pending LE connection, the background scanning is stopped.
Otherwise, we start the background scanning.

Then, every time a pending LE connection is added we call hci_update_
background_scan() so the background scanning is started (in case it is
not already running). Likewise, every time a pending LE connection is
deleted we call hci_update_background_scan() so the background scanning
is stopped (in case this was the last pending LE connection) or it is
started again (in case we have more pending LE connections). Finally,
we also call hci_update_background_scan() in hci_le_conn_failed() so
the background scan is restarted in case the connection establishment
fails. This way the background scanning keeps running until all pending
LE connection are established.

At this point, resolvable addresses are not support by this
infrastructure. The proper support is added in upcoming patches.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move address type conversion to outside hci_connect_le

This patch moves address type conversion (L2CAP address type to HCI
address type) to outside hci_connect_le. This way, we avoid back and
forth address type conversion in a comming patch.

So hci_connect_le() now expects 'dst_type' parameter in HCI address
type convention.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Refactor HCI connection code

hci_connect() is a very simple and useless wrapper of hci_connect_acl
and hci_connect_le functions. Addtionally, all places where hci_connect
is called the link type value is passed explicitly. This way, we can
safely delete hci_connect, declare hci_connect_acl and hci_connect_le
in hci_core.h and call them directly.

No functionality is changed by this patch.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove unused function

This patch removes hci_create_le_conn() since it is not used anymore.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Stop scanning on LE connection

Some LE controllers don't support scanning and creating a connection
at the same time. So we should always stop scanning in order to
establish the connection.

Since we may prematurely stop the discovery procedure in favor of
the connection establishment, we should also cancel hdev->le_scan_
disable delayed work and set the discovery state to DISCOVERY_STOPPED.

This change does a small improvement since it is not mandatory the
user stops scanning before connecting anymore. Moreover, this change
is required by upcoming LE auto connection mechanism in order to work
properly with controllers that don't support background scanning and
connection establishment at the same time.

In future, we might want to do a small optimization by checking if
controller is able to scan and connect at the same time. For now,
we want the simplest approach so we always stop scanning (even if
the controller is able to carry out both operations).

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Declare le_conn_failed in hci_core.h

This patch adds the "hci_" prefix to le_conn_failed() helper and
declares it in hci_core.h so it can be reused in hci_event.c.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use unresolvable private address for active scanning

When running active scanning during LE discovery, do not reveal the own
identity to the peer devices. In case LE privacy has been enabled, then
a resolvable private address is used. If the LE privacy option is off,
then use an unresolvable private address.

The public address or static random address is never used in active
scanning anymore. This ensures that scan request are send using a
random address.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix setting correct src_type when connecting LE

This patch ensures that conn->src_type contains the same address type as
is used for initiating the connection while the connection attempt is in
progress. Once connected this value will be overwritten with the
identity address type.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use hci_update_random_address() when connecting LE

When we initiate LE connections we need to update the local random
address if necessary. This patch updates the LE connection creation
mechanism to use the new hci_update_random_address() function to set the
own_address_type parameter and to update the local random address if
necessary.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use same LE min/max connection event length during update

During LE connection establishment the value 0x0000 is used for min/max
connection event length. So use the same value when the peripheral is
requesting an update of the the connection paramters.

For some reason the value 0x0001 got used in the connection update and
0x0000 in the connection creation. Using the same value for both just
makes sense.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix wrong identity address during connection failures

When the connection attempt fails, the address information are not
provided in the HCI_LE_Connection_Complete event. So use the original
information from the connection to reconstruct the identity address.

This is important when a connection attempt has been made using the
identity address, but the cached resolvable random address has changed
in the meantime. The failure event needs to use the identity address
and not the resolvable random address.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Look up RPA for connection requests with Identity Address

We need to check whether there's a matching IRK and RPA when we're
requested to connect to a remote LE device based on its Identity
Address. This patch updates the hci_connect_le function to do an extra
call to hci_find_irk_by_addr and uses the RPA if it's cached. This is
particularly important once we start exposing the Identity Address to
user space instead of the RPA in events such as Device Connected and
Device Found.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use connection parameters if any

This patch changes hci_connect_le() so it uses the connection
parameters specified for the certain device. If no parameters
were configured, we use the default values.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Include security level 4 in connections check

This check is only used for RFCOMM connections and most likely no
RFCOMM based profile will require security level 4 secure connection
security policy. In case it ever does make sure that seucrity level 4
is treated as sufficient security level.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Introduce le_conn_failed() helper

This patch moves connection attempt failure code to its own function
so it can be reused in the next patch.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Save connection interval parameters in hci_conn

This patch creates two new fields in struct hci_conn to save the
minimum and maximum connection interval values used to establish
the connection this object represents.

This change is required in order to know what parameters the
connection is currently using.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Introduce requirements for security level 4

The security level 4 is a new strong security requirement that is based
around 128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms. Which means that E0, SAFER+ and P-192
are not allowed. Only connections created with P-256 resulting from
using Secure Connections support are allowed.

This security level needs to be enforced when Secure Connection Only
mode is enabled for a controller or a service requires FIPS compliant
strong security. Currently it is not possible to enable either of
these two cases. This patch just puts in the foundation for being
able to handle security level 4 in the future.

It should be noted that devices or services with security level 4
requirement can only communicate using Bluetooth 4.1 controllers
with support for Secure Connections. There is no backward compatibilty
if used with older hardware.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add support for handling P-256 derived link keys

Before being able to enable Secure Connections support, the core needs
to know on how to handle P-256 derived link keys. The difference between
authenticated and unauthenticated P-256 derived link keys is the same as
its P-192 counter parts.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add definitions for new link key types

With the introduction of Secure Connections, the list of link key types
got extended by P-256 versions of authenticated and unauthenticated
link keys.

To avoid any confusion the previous authenticated and unauthenticated
link key types got ammended with a P912 postfix. And the two new keys
have a P256 postfix now. Existing code using the previous definitions
has been adjusted.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Expose debugfs settings for LE connection interval

For testing purposes expose the default LE connection interval values
via debugfs.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Select the own address type during initial setup phase

The own address type is based on the fact if the controller has
a public address or not. This means that this detail can be just
configured once during setup phase.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Convert idle timer to use delayed work

There is no need to use a timer since the entire Bluetooth subsystem
runs using workqueues these days.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Convert auto accept timer to use delayed work

Since the entire Bluetooth subsystem runs in workqueues these days there
is no need to use a timer for deferring work.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Store source address of HCI connections

The source addressed was based on the public address of the HCI device,
but with LE connections this not always the case. For example single
mode LE-only controllers would use a static random address. And this
address is configured by userspace.

To not complicate the lookup of what kind of address is in use, store
the correct source address for each HCI connection.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Store the source address type of LE connections

When establishing LE connections, it is possible to use a public
address (if available) or a random address. The type of address
is only known when creating connections, so make sure it is
stored in hci_conn structure.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Remove pointless bdaddr_to_le() helper function

The bdaddr_to_le() function tries to convert the internal address
type to one that matches the HCI address type for LE. It does not
handle any address types not used by LE and in the end just make
the code a lot harder to read.

So instead of just hiding behind a magic function, just convert
the internal address type where it needs to be converted. And it
turns out that these are only two cases anyway. One when creating
new LE connections and the other when loading the long term keys.
In both cases this makes it more clear on what it going on.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Make LE scan interval and window a controller option

The scan interval and window for LE passive scanning and connection
establishment should be configurable on a per controller basis. So
introduce a setting that later on will allow modifying it.

This setting does not affect LE active scanning during device
discovery phase. As long as that phase uses interleaved discovery,
it will continuously scan.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Move smp.h header file into net/bluetooth/

The smp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Move a2mp.h header file into net/bluetooth/

The a2mp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Refactor hci_connect_le

This patch does some code refactoring in hci_connect_le() by moving
the exception code into if statements and letting the main flow in
first level of function scope. It also adds extra comments to improve
the code readability.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use HCI request for LE connection

This patch introduces a new helper, which uses the HCI request
framework, for creating LE connectons. All the handling is now
done by this function so we can remove the hci_cs_le_create_conn()
event handler.

This patch also removes the old hci_le_create_connection() since
it is not used anymore.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use random address if public address is not available

For single mode LE-only controllers, it is possible that they come
without a public address. If a public address is not available,
then use the random address for connection establishment and
scanning.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Rename HCI_LE_PERIPHERAL to HCI_ADVERTISING

This flag is used to indicate whether we want to have advertising
enabled or not, so give it a more suitable name.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Initialize hci_conn fields in hci_connect_le

This patch moves some hci_conn fields initialization from hci_le_
create_connection() to hci_connect_le(). It makes more sense to
initialize these fields within the function that creates the hci_
conn object.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Rename hci_conn variable in hci_connect_le()

This patch simply rename the hci_conn variable "le" to "conn"
since it is a better name.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Introduce a new HCI_BREDR_ENABLED flag

To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).

This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.

We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Disable upper layer connections when user channel is active

When the device has the user channel flag set, it means it is driven by
an user application. In that case do not allow any connections from
L2CAP or SCO sockets.

This is the same situation as when the device has the raw flag set and
it will then return EHOSTUNREACH.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add SCO connection fallback

When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.

When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.

To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.

These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Parameters for outgoing SCO connections

In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use hci_connect_sco directly

hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: introduce hci_conn ref-counting

We currently do not allow using hci_conn from outside of HCI-core.
However, several other users could make great use of it. This includes
HIDP, rfcomm and all other sub-protocols that rely on an active
connection.

Hence, we now introduce hci_conn ref-counting. We currently never call
get_device(). put_device() is exclusively used in hci_conn_del_sysfs().
Hence, we currently never have a greater device-refcnt than 1.
Therefore, it is safe to move the put_device() call from
hci_conn_del_sysfs() to hci_conn_del() (it's the only caller). In fact,
this even fixes a "use-after-free" bug as we access hci_conn after calling
hci_conn_del_sysfs() in hci_conn_del().

From now on we can add references to hci_conn objects in other layers
(like l2cap_sock, HIDP, rfcomm, ...) and grab a reference via
hci_conn_get(). This does _not_ guarantee, that the connection is still
alive. But, this isn't what we want. We can simply lock the hci_conn
device and use "device_is_registered(hci_conn->dev)" to test that.
However, this is hardly necessary as outside users should never rely on
the HCI connection to be alive, anyway. Instead, they should solely rely
on the device-object to be available.
But if sub-devices want the hci_conn object as sysfs parent, they need to
be notified when the connection drops. This will be introduced in later
patches with l2cap_users.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: remove unneeded hci_conn_hold/put_device()

hci_conn_hold/put_device() is used to control when hci_conn->dev is no
longer needed and can be deleted from the system. Lets first look how they
are currently used throughout the code (excluding HIDP!).

All code that uses hci_conn_hold_device() looks like this:
...
hci_conn_hold_device();
hci_conn_add_sysfs();
...
On the other side, hci_conn_put_device() is exclusively used in
hci_conn_del().

So, considering that hci_conn_del() must not be called twice (which would
fail horribly), we know that hci_conn_put_device() is only called _once_
(which is in hci_conn_del()).
On the other hand, hci_conn_add_sysfs() must not be called twice, either
(it would call device_add twice, which breaks the device, see
drivers/base/core.c). So we know that hci_conn_hold_device() is also
called only once (it's only called directly before hci_conn_add_sysfs()).

So hold and put are known to be called only once. That means we can safely
remove them and directly call hci_conn_del_sysfs() in hci_conn_del().

But there is one issue left: HIDP also uses hci_conn_hold/put_device().
However, this case can be ignored and simply removed as it is totally
broken. The issue is, the only thing HIDP delays with
hci_conn_hold_device() is the removal of the hci_conn->dev from sysfs.
But, the hci_conn device has no mechanism to get notified when its own
parent (hci_dev) gets removed from sysfs. hci_dev_hold/put() does _not_
control when it is removed but only when the device object is created
and destroyed.
And hci_dev calls hci_conn_flush_*() when it removes itself from sysfs,
which itself causes hci_conn_del() to be called, but it does _not_ cause
hci_conn_del_sysfs() to be called, which is wrong.

Hence, we fix it to call hci_conn_del_sysfs() in hci_conn_del(). This
guarantees that a hci_conn object is removed from sysfs _before_ its
parent hci_dev is removed.

The changes to HIDP look scary, wrong and broken. However, if you look at
the HIDP session management, you will notice they're already broken in the
exact _same_ way (ever tried "unplugging" HIDP devices? Breaks _all_ the
time).
So this patch only makes HIDP look _scary_ and _obviously broken_. It does
not break HIDP itself, it already is!

See later patches in this series which fix HIDP to use proper
session-management.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Reject SCO when hci connection timeouts

This patch sends Reject Synchronous Connection Request Command when
hci_conn_timeout is triggered, and the SCO connection is in BT_CONNECT2
state. It prevents inconsistency if the remote host doesn't implement
properly the timeout for the connection request, and it removes the
connection reference left when the socket is closed for incoming SCO
connections.

[ 2650.129080] sco_sock_release: sock ffff8801ca417400, sk ffff88020c408800
[ 2650.129092] sco_sock_clear_timer: sock ffff88020c408800 state 6
[ 2650.129101] __sco_sock_close: sk ffff88020c408800 state 6 socket
ffff8801ca417400
[ 2650.129108] sco_chan_del: sk ffff88020c408800, conn ffff8801c650ea20,
err 104
[ 2650.129114] hci_conn_put: hcon ffff88020c40a800 orig refcnt 1
[ 2650.129128] sco_sock_kill: sk ffff88020c408800 state 9
[ 2650.129135] sco_sock_destruct: sk ffff88020c408800
[ 2650.138468] hci_conn_timeout: hcon ffff88020c40a800 state BT_CONNECT2

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: rename hci_conn_put to hci_conn_drop

We use _get() and _put() for device ref-counting in the kernel. However,
hci_conn_put() is _not_ used for ref-counting, hence, rename it to
hci_conn_drop() so we can later fix ref-counting and introduce
hci_conn_put().

hci_conn_hold() and hci_conn_put() are currently used to manage how long a
connection should be held alive. When the last user drops the connection,
we spawn a delayed work that performs the disconnect. Obviously, this has
nothing to do with ref-counting for the _object_ but rather for the
keep-alive of the connection.

But we really _need_ proper ref-counting for the _object_ to allow
connection-users like rfcomm-tty, HIDP or others.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>