timekeeping: Use READ/WRITE_ONCE() for tick_do_timer_cpu

tick_do_timer_cpu is used lockless to check which CPU needs to take care
of the per tick timekeeping duty. This is done to avoid a thundering
herd problem on jiffies_lock.

The read and writes are not annotated so KCSAN complains about data races:

BUG: KCSAN: data-race in tick_nohz_idle_stop_tick / tick_nohz_next_event

write to 0xffffffff8a2bda30 of 4 bytes by task 0 on cpu 26:
tick_nohz_idle_stop_tick+0x3b1/0x4a0
do_idle+0x1e3/0x250

read to 0xffffffff8a2bda30 of 4 bytes by task 0 on cpu 16:
tick_nohz_next_event+0xe7/0x1e0
tick_nohz_get_sleep_length+0xa7/0xe0
menu_select+0x82/0xb90
cpuidle_select+0x44/0x60
do_idle+0x1c2/0x250

value changed: 0x0000001a -> 0xffffffff

Annotate them with READ/WRITE_ONCE() to document the intentional data race.

Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/87cyqy7rt3.ffs@tglx

tick: Assume timekeeping is correctly handed over upon last offline idle call

The timekeeping duty is handed over from the outgoing CPU on stop
machine, then the oneshot tick is stopped right after. Therefore it's
guaranteed that the current CPU isn't the timekeeper upon its last call
to idle.

Besides, calling tick_nohz_idle_stop_tick() while the dying CPU goes
into idle suggests that the tick is going to be stopped while it is
actually stopped already from the appropriate CPU hotplug state.

Remove the confusing call and the obsolete case handling and convert it
to a sanity check that verifies the above assumption.

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-16-frederic@kernel.org

tick: Shut down low-res tick from dying CPU

The timekeeping duty is handed over from the outgoing CPU within stop
machine. This works well if CONFIG_NO_HZ_COMMON=n or the tick is in
high-res mode. However in low-res dynticks mode, the tick isn't
cancelled until the clockevent is shut down, which can happen later. The
tick may therefore fire again once IRQs are re-enabled on stop machine
and until IRQs are disabled for good upon the last call to idle.

That's so many opportunities for a timekeeper to go idle and the
outgoing CPU to take over that duty. This is why
tick_nohz_idle_stop_tick() is called one last time on idle if the CPU
is seen offline: so that the timekeeping duty is handed over again in
case the CPU has re-taken the duty.

This means there are two timekeeping handovers on CPU down hotplug with
different undocumented constraints and purposes:

1) A handover on stop machine for !dynticks || highres. All online CPUs
are guaranteed to be non-idle and the timekeeping duty can be safely
handed-over. The hrtimer tick is cancelled so it is guaranteed that in
dynticks mode the outgoing CPU won't take again the duty.

2) A handover on last idle call for dynticks && lowres. Setting the
duty to TICK_DO_TIMER_NONE makes sure that a CPU will take over the
timekeeping.

Prepare for consolidating the handover to a single place (the first one)
with shutting down the low-res tick as well from
tick_cancel_sched_timer() as well. This will simplify the handover and
unify the tick cancellation between high-res and low-res.

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-15-frederic@kernel.org

tick: Move broadcast cancellation up to CPUHP_AP_TICK_DYING

The broadcast shutdown code is executed through a random explicit call
within stop machine from the outgoing CPU.

However the tick broadcast is a midware between the tick callback and
the clocksource, therefore it makes more sense to shut it down after the
tick callback and before the clocksource drivers.

Move it instead to the common tick shutdown CPU hotplug state where
related operations can be ordered from highest to lowest level.

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-10-frederic@kernel.org

tick: Move tick cancellation up to CPUHP_AP_TICK_DYING

The tick hrtimer is cancelled right before hrtimers are migrated. This
is done from the hrtimer subsystem even though it shouldn't know about
its actual users.

Move instead the tick hrtimer cancellation to the relevant CPU hotplug
state that aims at centralizing high level tick shutdown operations so
that the related flow is easy to follow.

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-9-frederic@kernel.org

tick: Start centralizing tick related CPU hotplug operations

During the CPU offlining process, the various timer tick features are
shut down from scattered places, sometimes from teardown callbacks on
stop machine, sometimes through explicit calls, sometimes from the
control CPU after the CPU died. The reason why these shutdown operations
are spread around is not always clear and it makes the tick lifecycle
hard to follow.

The tick should be shut down in order from highest to lowest level:

On stop machine from the dying CPU (high-level):

1) Hand-over the timekeeping duty (tick_handover_do_timer())
2) Cancel the tick implementation called by the clockevent callback
(tick_cancel_sched_timer())
3) Shutdown broadcasting (tick_offline_cpu() / tick_broadcast_offline())

On stop machine from the dying CPU (low-level):

4) Shutdown clockevents drivers (CPUHP_AP_*_TIMER_STARTING states)

From the control CPU after the CPU died (low-level):

5) Shutdown/unregister/cleanup clockevents for the dead CPU
(tick_cleanup_dead_cpu())

Instead the current order is 2, 4 (both from CPU hotplug states), then
1 and 3 through direct calls. This layout and order don't make much
sense. The operations 1, 2, 3 should be gathered together and in order.

Sort this situation with creating a new TICK shut-down CPU hotplug state
and start with introducing the timekeeping duty hand-over there. The
state must precede hrtimers migration because the tick hrtimer will be
stopped from it in a further patch.

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-8-frederic@kernel.org

tick: Use IS_ENABLED() whenever possible

Avoid ifdeferry if it can be converted to IS_ENABLED() whenever possible

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-5-frederic@kernel.org

tick/common: Align tick period during sched_timer setup

The tick period is aligned very early while the first clock_event_device is
registered. At that point the system runs in periodic mode and switches
later to one-shot mode if possible.

The next wake-up event is programmed based on the aligned value
(tick_next_period) but the delta value, that is used to program the
clock_event_device, is computed based on ktime_get().

With the subtracted offset, the device fires earlier than the exact time
frame. With a large enough offset the system programs the timer for the
next wake-up and the remaining time left is too small to make any boot
progress. The system hangs.

Move the alignment later to the setup of tick_sched timer. At this point
the system switches to oneshot mode and a high resolution clocksource is
available. At this point it is safe to align tick_next_period because
ktime_get() will now return accurate (not jiffies based) time.

[bigeasy: Patch description + testing].

Fixes: e9523a0d81899 ("tick/common: Align tick period with the HZ tick.")
Reported-by: Mathias Krause <minipli@grsecurity.net>
Reported-by: "Bhatnagar, Rishabh" <risbhat@amazon.com>
Suggested-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Mathias Krause <minipli@grsecurity.net>
Acked-by: SeongJae Park <sj@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/5a56290d-806e-b9a5-f37c-f21958b5a8c0@grsecurity.net
Link: https://lore.kernel.org/12c6f9a3-d087-b824-0d05-0d18c9bc1bf3@amazon.com
Link: https://lore.kernel.org/r/20230615091830.RxMV2xf_@linutronix.de

tick/common: Align tick period with the HZ tick.

With HIGHRES enabled tick_sched_timer() is programmed every jiffy to
expire the timer_list timers. This timer is programmed accurate in
respect to CLOCK_MONOTONIC so that 0 seconds and nanoseconds is the
first tick and the next one is 1000/CONFIG_HZ ms later. For HZ=250 it is
every 4 ms and so based on the current time the next tick can be
computed.

This accuracy broke since the commit mentioned below because the jiffy
based clocksource is initialized with higher accuracy in
read_persistent_wall_and_boot_offset(). This higher accuracy is
inherited during the setup in tick_setup_device(). The timer still fires
every 4ms with HZ=250 but timer is no longer aligned with
CLOCK_MONOTONIC with 0 as it origin but has an offset in the us/ns part
of the timestamp. The offset differs with every boot and makes it
impossible for user land to align with the tick.

Align the tick period with CLOCK_MONOTONIC ensuring that it is always a
multiple of 1000/CONFIG_HZ ms.

Fixes: 857baa87b6422 ("sched/clock: Enable sched clock early")
Reported-by: Gusenleitner Klaus <gus@keba.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/20230406095735.0_14edn3@linutronix.de
Link: https://lore.kernel.org/r/20230418122639.ikgfvu3f@linutronix.de

timekeeping: Distangle resume and clock-was-set events

Resuming timekeeping is a clock-was-set event and uses the clock-was-set
notification mechanism. This is in the way of making the clock-was-set
update for hrtimers selective so unnecessary IPIs are avoided when a CPU
base does not have timers queued which are affected by the clock setting.

Distangle it by invoking hrtimer_resume() on each unfreezing CPU and invoke
the new timerfd_resume() function from timekeeping_resume() which is the
only place where this is needed.

Rename hrtimer_resume() to hrtimer_resume_local() to reflect the change.

With this the clock_was_set*() functions are not longer required to IPI all
CPUs unconditionally and can get some smarts to avoid them.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.488853478@linutronix.de

tick/broadcast: Prefer per-cpu oneshot wakeup timers to broadcast

Some SoCs have two per-cpu timer implementations where the timer with the
higher rating stops in deep idle (i.e. suffers from CLOCK_EVT_FEAT_C3STOP)
but is otherwise preferable to the timer with the lower rating. In such a
design, selecting the higher rated devices relies on a global broadcast
timer and IPIs to wake up from deep idle states.

To avoid the reliance on a global broadcast timer and also to reduce the
overhead associated with the IPI wakeups, extend
tick_install_broadcast_device() to manage per-cpu wakeup timers separately
from the broadcast device.

For now, these timers remain unused.

Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210524221818.15850-4-will@kernel.org

tick: Use tick_check_replacement() instead of open coding it

The function tick_check_replacement() is the combination of
tick_check_percpu() and tick_check_preferred(), but tick_check_new_device()
has the same logic open coded.

Use the helper to simplify the code.

[ tglx: Massage changelog ]

Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210326022328.3266-1-wangwensheng4@huawei.com

tick: Remove pointless cpu valid check in hotplug code

tick_handover_do_timer() which is invoked when a CPU is unplugged has a
check for cpumask_first(cpu_online_mask) when it tries to hand over the
tick update duty.

Checking the result of cpumask_first() there is pointless because if the
online mask is empty at this point, then this would be the last CPU in the
system going offline, which is impossible. There is always at least one CPU
remaining. If online mask would be really empty then the timer duty would
be the least of the resulting problems.

Remove the well meant check simply because it is pointless and confusing.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20201206212002.582579516@linutronix.de

tick: Get rid of tick_period

The variable tick_period is initialized to NSEC_PER_TICK / HZ during boot
and never updated again.

If NSEC_PER_TICK is not an integer multiple of HZ this computation is less
accurate than TICK_NSEC which has proper rounding in place.

Aside of the inaccuracy there is no reason for having this variable at
all. It's just a pointless indirection and all usage sites can just use the
TICK_NSEC constant.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201117132006.766643526@linutronix.de

tick: Document protections for tick related data

The protection rules for tick_next_period and last_jiffies_update are blury
at best. Clarify this.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201117132006.197713794@linutronix.de

timekeeping: Split jiffies seqlock

seqlock consists of a sequence counter and a spinlock_t which is used to
serialize the writers. spinlock_t is substituted by a "sleeping" spinlock
on PREEMPT_RT enabled kernels which breaks the usage in the timekeeping
code as the writers are executed in hard interrupt and therefore
non-preemptible context even on PREEMPT_RT.

The spinlock in seqlock cannot be unconditionally replaced by a
raw_spinlock_t as many seqlock users have nesting spinlock sections or
other code which is not suitable to run in truly atomic context on RT.

Instead of providing a raw_seqlock API for a single use case, open code the
seqlock for the jiffies use case and implement it with a raw_spinlock_t and
a sequence counter.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200321113242.120587764@linutronix.de

Revert "tick/common: Make tick_periodic() check for missing ticks"

This reverts commit d441dceb5dce71150f28add80d36d91bbfccba99 due to
boot failures.

Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>

tick/common: Make tick_periodic() check for missing ticks

The tick_periodic() function is used at the beginning part of the
bootup process for time keeping while the other clock sources are
being initialized.

The current code assumes that all the timer interrupts are handled in
a timely manner with no missing ticks. That is not actually true. Some
ticks are missed and there are some discrepancies between the tick time
(jiffies) and the timestamp reported in the kernel log. Some systems,
however, are more prone to missing ticks than the others. In the extreme
case, the discrepancy can actually cause a soft lockup message to be
printed by the watchdog kthread. For example, on a Cavium ThunderX2
Sabre arm64 system:

[ 25.496379] watchdog: BUG: soft lockup - CPU#14 stuck for 22s!

On that system, the missing ticks are especially prevalent during the
smp_init() phase of the boot process. With an instrumented kernel,
it was found that it took about 24s as reported by the timestamp for
the tick to accumulate 4s of time.

Investigation and bisection done by others seemed to point to the
commit 73f381660959 ("arm64: Advertise mitigation of Spectre-v2, or
lack thereof") as the culprit. It could also be a firmware issue as
new firmware was promised that would fix the issue.

To properly address this problem, stop assuming that there will be no
missing tick in tick_periodic(). Modify it to follow the example of
tick_do_update_jiffies64() by using another reference clock to check for
missing ticks. Since the watchdog timer uses running_clock(), it is used
here as the reference. With this applied, the soft lockup problem in the
affected arm64 system is gone and tick time tracks much more closely to the
timestamp time.

Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200207193929.27308-1-longman@redhat.com

tick/common: Touch watchdog in tick_unfreeze() on all CPUs

Suspend to IDLE invokes tick_unfreeze() on resume. tick_unfreeze() on the
first resuming CPU resumes timekeeping, which also has the side effect of
resetting the softlockup watchdog on this CPU.

But on the secondary CPUs the watchdog is not reset in the resume /
unfreeze() path, which can result in false softlockup warnings on those
CPUs depending on the time spent in suspend.

Prevent this by clearing the softlock watchdog in the unfreeze path also
on the secondary resuming CPUs.

[ tglx: Massaged changelog ]

Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200110083902.27276-1-chunyan.zhang@unisoc.com

nohz_full: Allow the boot CPU to be nohz_full

Allow the boot CPU/CPU0 to be nohz_full. Have the boot CPU take the
do_timer duty during boot until a housekeeping CPU can take over.

This is supported when CONFIG_PM_SLEEP_SMP is not configured, or when
it is configured and the arch allows suspend on non-zero CPUs.

nohz_full has been trialed at a large supercomputer site and found to
significantly reduce jitter. In order to deploy it in production, they
need CPU0 to be nohz_full because their job control system requires
the application CPUs to start from 0, and the housekeeping CPUs are
placed higher. An equivalent job scheduling that uses CPU0 for
housekeeping could be achieved by modifying their system, but it is
preferable if nohz_full can support their environment without
modification.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lkml.kernel.org/r/20190411033448.20842-6-npiggin@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

timers/sched_clock: Prevent generic sched_clock wrap caused by tick_freeze()

tick_freeze() introduced by suspend-to-idle in commit 124cf9117c5f ("PM /
sleep: Make it possible to quiesce timers during suspend-to-idle") uses
timekeeping_suspend() instead of syscore_suspend() during
suspend-to-idle. As a consequence generic sched_clock will keep going
because sched_clock_suspend() and sched_clock_resume() are not invoked
during suspend-to-idle which can result in a generic sched_clock wrap.

On a ARM system with suspend-to-idle enabled, sched_clock is registered
as "56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns", which
means the real wrapping duration is 8796093022202ns.

[ 134.551779] suspend-to-idle suspend (timekeeping_suspend())
[ 1204.912239] suspend-to-idle resume (timekeeping_resume())
......
[ 1206.912239] suspend-to-idle suspend (timekeeping_suspend())
[ 5880.502807] suspend-to-idle resume (timekeeping_resume())
......
[ 6000.403724] suspend-to-idle suspend (timekeeping_suspend())
[ 8035.753167] suspend-to-idle resume (timekeeping_resume())
......
[ 8795.786684] (2)[321:charger_thread]......
[ 8795.788387] (2)[321:charger_thread]......
[ 0.057226] (0)[0:swapper/0]......
[ 0.061447] (2)[0:swapper/2]......

sched_clock was not stopped during suspend-to-idle, and sched_clock_poll
hrtimer was not expired because timekeeping_suspend() was invoked during
suspend-to-idle. It makes sched_clock wrap at kernel time 8796s.

To prevent this, invoke sched_clock_suspend() and sched_clock_resume() in
tick_freeze() together with timekeeping_suspend() and timekeeping_resume().

Fixes: 124cf9117c5f (PM / sleep: Make it possible to quiesce timers during suspend-to-idle)
Signed-off-by: Chang-An Chen <chang-an.chen@mediatek.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Corey Minyard <cminyard@mvista.com>
Cc: <linux-mediatek@lists.infradead.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: <kuohong.wang@mediatek.com>
Cc: <freddy.hsin@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1553828349-8914-1-git-send-email-chang-an.chen@mediatek.com

timekeeping: Consistently use unsigned int for seqcount snapshot

The timekeeping code uses a random mix of "unsigned long" and "unsigned
int" for the seqcount snapshots (ratio 14:12). Since the seqlock.h API is
entirely based on unsigned int, use that throughout.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190318195557.20773-1-linux@rasmusvillemoes.dk

hrtimers/tick/clockevents: Remove sloppy license references

"For licencing details see kernel-base/COPYING" and similar license
references have no value over the SPDX identifier. Remove them.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: David Riley <davidriley@chromium.org>
Cc: Colin Cross <ccross@android.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lkml.kernel.org/r/20181031182252.963632760@linutronix.de

time: Add SPDX license identifiers

Update the time(r) core files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of the
full boiler plate text.

This work is based on a script and data from Philippe Ombredanne, Kate
Stewart and myself. The data has been created with two independent license
scanners and manual inspection.

The following files do not contain any direct license information and have
been omitted from the big initial SPDX changes:

timeconst.bc: The .bc files were not touched
time.c, timer.c, timekeeping.c: Licence was deduced from EXPORT_SYMBOL_GPL

As those files do not contain direct license references they fall under the
project license, i.e. GPL V2 only.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: David Riley <davidriley@chromium.org>
Cc: Colin Cross <ccross@android.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20181031182252.879109557@linutronix.de

time: Remove useless filenames in top level comments

Remove the pointless filenames in the top level comments. They have no
value at all and just occupy space. While at it tidy up some of the
comments and remove a stale one.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Riley <davidriley@chromium.org>
Cc: Colin Cross <ccross@android.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lkml.kernel.org/r/20181031182252.794898238@linutronix.de

Revert "tick: Prefer a lower rating device only if it's CPU local device"

This reverts commit 1332a90558013ae4242e3dd7934bdcdeafb06c0d.

The original issue was not because of incorrect checking of cpumask for
both new and old tick device. It was incorrectly analysed was due to the
misunderstanding of the comment and misinterpretation of the return value
from tick_check_preferred. The main issue is with the clockevent driver
that sets the cpumask to cpu_all_mask instead of cpu_possible_mask.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1531151136-18297-1-git-send-email-sudeep.holla@arm.com

PM / suspend: Prevent might sleep splats

timekeeping suspend/resume calls read_persistent_clock() which takes
rtc_lock. That results in might sleep warnings because at that point
we run with interrupts disabled.

We cannot convert rtc_lock to a raw spinlock as that would trigger
other might sleep warnings.

As a workaround we disable the might sleep warnings by setting
system_state to SYSTEM_SUSPEND before calling sysdev_suspend() and
restoring it to SYSTEM_RUNNING afer sysdev_resume(). There is no lock
contention because hibernate / suspend to RAM is single-CPU at this
point.

In s2idle's case the system_state is set to SYSTEM_SUSPEND before
timekeeping_suspend() which is invoked by the last CPU. In the resume
case it set back to SYSTEM_RUNNING after timekeeping_resume() which is
invoked by the first CPU in the resume case. The other CPUs will block
on tick_freeze_lock.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: cover s2idle in tick_freeze() / tick_unfreeze()]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

tick: Prefer a lower rating device only if it's CPU local device

Checking the equality of cpumask for both new and old tick device doesn't
ensure that it's CPU local device. This will cause issue if a low rating
clockevent tick device is registered first followed by the registration
of higher rating clockevent tick device.

In such case, clockevents_released list will never get emptied as both
the devices get selected as preferred one and we will loop forever in
clockevents_notify_released.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: https://lkml.kernel.org/r/1525881728-4858-1-git-send-email-sudeep.holla@arm.com

Revert: Unify CLOCK_MONOTONIC and CLOCK_BOOTTIME

Revert commits

92af4dcb4e1c ("tracing: Unify the "boot" and "mono" tracing clocks")
127bfa5f4342 ("hrtimer: Unify MONOTONIC and BOOTTIME clock behavior")
7250a4047aa6 ("posix-timers: Unify MONOTONIC and BOOTTIME clock behavior")
d6c7270e913d ("timekeeping: Remove boot time specific code")
f2d6fdbfd238 ("Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior")
d6ed449afdb3 ("timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock")
72199320d49d ("timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock")

As stated in the pull request for the unification of CLOCK_MONOTONIC and
CLOCK_BOOTTIME, it was clear that we might have to revert the change.

As reported by several folks systemd and other applications rely on the
documented behaviour of CLOCK_MONOTONIC on Linux and break with the above
changes. After resume daemons time out and other timeout related issues are
observed. Rafael compiled this list:

* systemd kills daemons on resume, after >WatchdogSec seconds
of suspending (Genki Sky). [Verified that that's because systemd uses
CLOCK_MONOTONIC and expects it to not include the suspend time.]

* systemd-journald misbehaves after resume:
systemd-journald[7266]: File /var/log/journal/016627c3c4784cd4812d4b7e96a34226/system.journal
corrupted or uncleanly shut down, renaming and replacing.
(Mike Galbraith).

* NetworkManager reports "networking disabled" and networking is broken
after resume 50% of the time (Pavel). [May be because of systemd.]

* MATE desktop dims the display and starts the screensaver right after
system resume (Pavel).

* Full system hang during resume (me). [May be due to systemd or NM or both.]

That happens on debian and open suse systems.

It's sad, that these problems were neither catched in -next nor by those
folks who expressed interest in this change.

Reported-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Reported-by: Genki Sky <sky@genki.is>,
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kevin Easton <kevin@guarana.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salyzyn <salyzyn@android.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>

timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock

The MONOTONIC clock is not fast forwarded by the time spent in suspend on
resume. This is only done for the BOOTTIME clock. The reason why the
MONOTONIC clock is not forwarded is historical: the original Linux
implementation was using jiffies as a base for the MONOTONIC clock and
jiffies have never been advanced after resume.

At some point when timekeeping was unified in the core code, the
MONONOTIC clock was advanced after resume which also advanced jiffies causing
interesting side effects. As a consequence the the MONOTONIC clock forwarding
was disabled again and the BOOTTIME clock was introduced, which allows to read
time since boot.

Back then it was not possible to completely distangle the MONOTONIC clock and
jiffies because there were still interfaces which exposed the MONOTONIC clock
behaviour based on the timer wheel and therefore jiffies.

As of today none of the MONOTONIC clock facilities depends on jiffies
anymore so the forwarding can be done seperately. This is achieved by
forwarding the variables which are used for the jiffies update after resume
before the tick is restarted,

In timekeeping resume, the change is rather simple. Instead of updating the
offset between the MONOTONIC clock and the REALTIME/BOOTTIME clocks, advance the
time keeper base for the MONOTONIC and the MONOTONIC_RAW clocks by the time
spent in suspend.

The MONOTONIC clock is now the same as the BOOTTIME clock and the offset between
the REALTIME and the MONOTONIC clocks is the same as before suspend.

There might be side effects in applications, which rely on the
(unfortunately) well documented behaviour of the MONOTONIC clock, but the
downsides of the existing behaviour are probably worse.

There is one obvious issue. Up to now it was possible to retrieve the time
spent in suspend by observing the delta between the MONOTONIC clock and the
BOOTTIME clock. This is not longer available, but the previously introduced
mechanism to read the active non-suspended monotonic time can mitigate that
in a detectable fashion.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kevin Easton <kevin@guarana.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salyzyn <salyzyn@android.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20180301165150.062975504@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>

ktime: Cleanup ktime_set() usage

ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

clockevents: Remove unused set_mode() callback

All users are migrated to the per-state callbacks, get rid of the
unused interface and the core support code.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linaro-kernel@lists.linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/fd60de14cf6d125489c031207567bb255ad946f6.1441943991.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

clockevents: Drop redundant cpumask check in tick_check_new_device()

The same check is performed by tick_check_percpu().

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Link: http://lkml.kernel.org/r/20150729151417.069d1bb0@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

tick: Move the export of tick_broadcast_oneshot_control to the proper place

tick_broadcast_oneshot_control got moved from tick-broadcast to
tick-common, but the export stayed in the old place. Fix it up.

Fixes: f32dd1170511 'tick/broadcast: Make idle check independent from mode and config'
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

tick/broadcast: Make idle check independent from mode and config

Currently the broadcast busy check, which prevents the idle code from
going into deep idle, works only in one shot mode.

If NOHZ and HIGHRES are off (config or command line) there is no
sanity check at all, so under certain conditions cpus are allowed to
go into deep idle, where the local timer stops, and are not woken up
again because there is no broadcast timer installed or a hrtimer based
broadcast device is not evaluated.

Move tick_broadcast_oneshot_control() into the common code and provide
proper subfunctions for the various config combinations.

The common check in tick_broadcast_oneshot_control() is for the C3STOP
misfeature flag of the local clock event device. If its not set, idle
can proceed. If set, further checks are necessary.

Provide checks for the trivial cases:

- If broadcast is disabled in the config, then return busy

- If oneshot mode (NOHZ/HIGHES) is disabled in the config, return
busy if the broadcast device is hrtimer based.

- If oneshot mode is enabled in the config call the original
tick_broadcast_oneshot_control() function. That function needs
extra checks which will be implemented in seperate patches.

[ Split out from a larger combo patch ]

Reported-and-tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Suzuki Poulose <Suzuki.Poulose@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Catalin Marinas <Catalin.Marinas@arm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1507070929360.3916@nanos

clockevents: Use set/get state helper functions

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>

clockevents: Provide functions to set and get the state

We want to rename dev->state, so provide proper get and set
functions. Rename clockevents_set_state() to
clockevents_switch_state() to avoid confusion.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>

clockevents: Use helpers to check the state of a clockevent device

Use accessor functions to check the state of clockevent devices in
core code.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/fa2b9869fd17f210eaa156ec2b594efd0230b6c7.1432192527.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

PM / sleep: Make suspend-to-idle-specific code depend on CONFIG_SUSPEND

Since idle_should_freeze() is defined to always return 'false'
for CONFIG_SUSPEND unset, all of the code depending on it in
cpuidle_idle_call() is not necessary in that case.

Make that code depend on CONFIG_SUSPEND too to avoid building it
when it is not going to be used.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>

PM / tick: Add tracepoints for suspend-to-idle diagnostics

Add suspend/resume tracepoints to tick_freeze() and tick_unfreeze()
to catch when timekeeping is suspended and resumed during suspend-to-idle
so as to be able to check whether or not we enter the "frozen" state
and to measure the time spent in it.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>

hrtimer: Get rid of hrtimer softirq

hrtimer softirq is a leftover from the initial implementation and
serves only the purpose to handle the enqueueing of already expired
timers in the high resolution timer mode. We discussed whether we
change the return value and force all start sites to handle that the
timer is already expired, but that would be a Herculean task and I'm
not sure whether its a good idea to enforce that handling on
everyone.

A simpler solution is to enforce a timer interrupt instead of raising
and scheduling a softirq. Just use the existing infrastructure to do
so and remove all the softirq leftovers.

The HRTIMER softirq enum is now unused, but kept around because trace
parsers rely on the existing numbering.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20150414203501.840834708@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

timers/PM: Drop unnecessary braces from tick_freeze()

Some braces in tick_freeze() are not necessary, so drop them.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: peterz@infradead.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1534128.H5hN3KBFB4@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>

timers/PM: Fix up tick_unfreeze()

A recent conflict resolution has left tick_resume() in
tick_unfreeze() which leads to an unbalanced execution of
tick_resume_broadcast() every time that function runs.

Fix that by replacing the tick_resume() in tick_unfreeze()
with tick_resume_local() as appropriate.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: boris.ostrovsky@oracle.com
Cc: david.vrabel@citrix.com
Cc: konrad.wilk@oracle.com
Cc: peterz@infradead.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/8099075.V0LvN3pQAV@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>

clockevents: Cleanup dead cpu explicitely

clockevents_notify() is a leftover from the early design of the
clockevents facility. It's really not a notification mechanism,
it's a multiplex call. We are way better off to have explicit
calls instead of this monstrosity.

Split out the cleanup function for a dead cpu and invoke it
directly from the cpu down code. Make it conditional on
CPU_HOTPLUG as well.

Temporary change, will be refined in the future.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Rebased, added clockevents_notify() removal ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1735025.raBZdQHM3m@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>

clockevents: Make tick handover explicit

clockevents_notify() is a leftover from the early design of the
clockevents facility. It's really not a notification mechanism,
it's a multiplex call. We are way better off to have explicit
calls instead of this monstrosity.

Split out the tick_handover call and invoke it explicitely from
the hotplug code. Temporary solution will be cleaned up in later
patches.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Rebase ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1658173.RkEEILFiQZ@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>

arm/bL_switcher: Kill tick suspend hackery

Use the new tick_suspend/resume_local() and get rid of the
homebrewn implementation of these in the ARM bL switcher. The
check for the cpumask is completely pointless. There is no harm
to suspend a per cpu tick device unconditionally. If that's a
real issue then we fix it proper at the core level and not with
some completely undocumented hacks in some random core code.

Move the tick internals to the core code, now that this nuisance
is gone.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ rjw: Rebase, changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1655112.Ws17YsMfN7@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>

tick/xen: Provide and use tick_suspend_local() and tick_resume_local()

Xen calls on every cpu into tick_resume() which is just wrong.
tick_resume() is for the syscore global suspend/resume
invocation. What XEN really wants is a per cpu local resume
function.

Provide a tick_resume_local() function and use it in XEN.

Also provide a complementary tick_suspend_local() and modify
tick_unfreeze() and tick_freeze(), respectively, to use the
new local tick resume/suspend functions.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Combined two patches, rebased, modified subject/changelog. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1698741.eezk9tnXtG@vostro.rjw.lan
[ Merged to latest timers/core. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>

clockevents: Make suspend/resume calls explicit

clockevents_notify() is a leftover from the early design of the
clockevents facility. It's really not a notification mechanism,
it's a multiplex call.

We are way better off to have explicit calls instead of this
monstrosity. Split out the suspend/resume() calls and invoke
them directly from the call sites.

No locking required at this point because these calls happen
with interrupts disabled and a single cpu online.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Rebased on top of 4.0-rc5. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/713674030.jVm1qaHuPf@vostro.rjw.lan
[ Rebased on top of latest timers/core. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>

clockevents: Manage device's state separately for the core

'enum clock_event_mode' is used for two purposes today:

- to pass mode to the driver of clockevent device::set_mode().

- for managing state of the device for clockevents core.

For supporting new modes/states we have moved away from the
legacy set_mode() callback to new per-mode/state callbacks. New
modes/states shouldn't be exposed to the legacy (now OBSOLOTE)
callbacks and so we shouldn't add new states to 'enum
clock_event_mode'.

Lets have separate enums for the two use cases mentioned above.
Keep using the earlier enum for legacy set_mode() callback and
mark it OBSOLETE. And add another enum to clearly specify the
possible states of a clockevent device.

This also renames the newly added per-mode callbacks to reflect
state changes.

We haven't got rid of 'mode' member of 'struct
clock_event_device' as it is used by some of the clockevent
drivers and it would automatically die down once we migrate
those drivers to the new interface. It ('mode') is only updated
now for the drivers using the legacy interface.

Suggested-by: Peter Zijlstra <peterz@infradead.org>
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: linaro-kernel@lists.linaro.org
Cc: linaro-networking@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/b6b0143a8a57bd58352ad35e08c25424c879c0cb.1425037853.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

clockevents: Handle tick device's resume separately

Upcoming patch will redefine possible states of a clockevent
device. The RESUME mode is a special case only for tick's
clockevent devices. In future it can be replaced by ->resume()
callback already available for clockevent devices.

Lets handle it separately so that clockevents_set_mode() only
handles states valid across all devices. This also renames
set_mode_resume() to tick_resume() to make it more explicit.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: linaro-kernel@lists.linaro.org
Cc: linaro-networking@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/c1b0112410870f49e7bf06958e1483eac6c15e20.1425037853.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

PM / sleep: Make it possible to quiesce timers during suspend-to-idle

The efficiency of suspend-to-idle depends on being able to keep CPUs
in the deepest available idle states for as much time as possible.
Ideally, they should only be brought out of idle by system wakeup
interrupts.

However, timer interrupts occurring periodically prevent that from
happening and it is not practical to chase all of the "misbehaving"
timers in a whack-a-mole fashion. A much more effective approach is
to suspend the local ticks for all CPUs and the entire timekeeping
along the lines of what is done during full suspend, which also
helps to keep suspend-to-idle and full suspend reasonably similar.

The idea is to suspend the local tick on each CPU executing
cpuidle_enter_freeze() and to make the last of them suspend the
entire timekeeping. That should prevent timer interrupts from
triggering until an IO interrupt wakes up one of the CPUs. It
needs to be done with interrupts disabled on all of the CPUs,
though, because otherwise the suspended clocksource might be
accessed by an interrupt handler which might lead to fatal
consequences.

Unfortunately, the existing ->enter callbacks provided by cpuidle
drivers generally cannot be used for implementing that, because some
of them re-enable interrupts temporarily and some idle entry methods
cause interrupts to be re-enabled automatically on exit. Also some
of these callbacks manipulate local clock event devices of the CPUs
which really shouldn't be done after suspending their ticks.

To overcome that difficulty, introduce a new cpuidle state callback,
->enter_freeze, that will be guaranteed (1) to keep interrupts
disabled all the time (and return with interrupts disabled) and (2)
not to touch the CPU timer devices. Modify cpuidle_enter_freeze() to
look for the deepest available idle state with ->enter_freeze present
and to make the CPU execute that callback with suspended tick (and the
last of the online CPUs to execute it with suspended timekeeping).

Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>

nohz: Move nohz full init call to tick init

This way we unbloat a bit main.c and more importantly we initialize
nohz full after init_IRQ(). This dependency will be needed in further
patches because nohz full needs irq work to raise its own IRQ.
Information about the support for this ability on ARM64 is obtained on
init_IRQ() which initialize the pointer to __smp_call_function.

Since tick_init() is called right after init_IRQ(), this is a good place
to call tick_nohz_init() and prepare for that dependency.

Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>

time: Replace __get_cpu_var uses

Convert uses of __get_cpu_var for creating a address from a percpu
offset to this_cpu_ptr.

The two cases where get_cpu_var is used to actually access a percpu
variable are changed to use this_cpu_read/raw_cpu_read.

Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

tick-common: Fix wrong check in tick_check_replacement()

tick_check_replacement() returns if a replacement of clock_event_device is
possible or not. It does this as the first check:

if (tick_check_percpu(curdev, newdev, smp_processor_id()))
return false;

Thats wrong. tick_check_percpu() returns true when the device is
useable. Check for false instead.

[ tglx: Massaged changelog ]

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org> # v3.11+
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: Arvind.Chauhan@arm.com
Cc: linaro-networking@linaro.org
Link: http://lkml.kernel.org/r/486a02efe0246635aaba786e24b42d316438bf3b.1397537987.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

tick: Remove code duplication in tick_handle_periodic()

tick_handle_periodic() is calling ktime_add() at two places, first before the
infinite loop and then at the end of infinite loop. We can rearrange code a bit
to fix code duplication here.

It looks quite simple and shouldn't break anything, I guess :)

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Link: http://lkml.kernel.org/r/be3481e8f3f71df694a4b43623254fc93ca51b59.1395735873.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

tick: Fix spelling mistake in tick_handle_periodic()

One of the comments in tick_handle_periodic() had 'when' instead of 'which' (My
guess :)). Fix it.

Also fix spelling mistake in 'Possible'.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: skarafotis@gmail.com
Link: http://lkml.kernel.org/r/2b29ca4230c163e44179941d7c7a16c1474385c2.1395743878.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

tick/timekeeping: Call update_wall_time outside the jiffies lock

Since the xtime lock was split into the timekeeping lock and
the jiffies lock, we no longer need to call update_wall_time()
while holding the jiffies lock.

Thus, this patch splits update_wall_time() out from do_timer().

This allows us to get away from calling clock_was_set_delayed()
in update_wall_time() and instead use the standard clock_was_set()
call that previously would deadlock, as it causes the jiffies lock
to be acquired.

Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>

tick: Document tick_do_timer_cpu

Taken straight from a tglx email ;)

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

tick: Sanitize broadcast control logic

The recent implementation of a generic dummy timer resulted in a
different registration order of per cpu local timers which made the
broadcast control logic go belly up.

If the dummy timer is the first clock event device which is registered
for a CPU, then it is installed, the broadcast timer is initialized
and the CPU is marked as broadcast target.

If a real clock event device is installed after that, we can fail to
take the CPU out of the broadcast mask. In the worst case we end up
with two periodic timer events firing for the same CPU. One from the
per cpu hardware device and one from the broadcast.

Now the problem is that we have no way to distinguish whether the
system is in a state which makes broadcasting necessary or the
broadcast bit was set due to the nonfunctional dummy timer
installment.

To solve this we need to keep track of the system state seperately and
provide a more detailed decision logic whether we keep the CPU in
broadcast mode or not.

The old decision logic only clears the broadcast mode, if the newly
installed clock event device is not affected by power states.

The new logic clears the broadcast mode if one of the following is
true:

- The new device is not affected by power states.

- The system is not in a power state affected mode

- The system has switched to oneshot mode. The oneshot broadcast is
controlled from the deep idle state. The CPU is not in idle at
this point, so it's safe to remove it from the mask.

If we clear the broadcast bit for the CPU when a new device is
installed, we also shutdown the broadcast device when this was the
last CPU in the broadcast mask.

If the broadcast bit is kept, then we leave the new device in shutdown
state and rely on the broadcast to deliver the timer interrupts via
the broadcast ipis.

Reported-and-tested-by: Stehle Vincent-B46079 <B46079@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Mark Rutland <mark.rutland@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1307012153060.4013@ionos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Prefer CPU local devices over global devices

On an SMP system with only one global clockevent and a dummy
clockevent per CPU we run into problems. We want the dummy
clockevents to be registered as the per CPU tick devices, but
we can only achieve that if we register the dummy clockevents
before the global clockevent or if we artificially inflate the
rating of the dummy clockevents to be higher than the rating
of the global clockevent. Failure to do so leads to boot
hangs when the dummy timers are registered on all other CPUs
besides the CPU that accepted the global clockevent as its tick
device and there is no broadcast timer to poke the dummy
devices.

If we're registering multiple clockevents and one clockevent is
global and the other is local to a particular CPU we should
choose to use the local clockevent regardless of the rating of
the device. This way, if the clockevent is a dummy it will take
the tick device duty as long as there isn't a higher rated tick
device and any global clockevent will be bumped out into
broadcast mode, fixing the problem described above.

Reported-and-tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: soren.brinkmann@xilinx.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20130613183950.GA32061@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Implement unbind functionality

Provide a sysfs interface to allow unbinding of clockevent
devices. The device is unbound if it is unused or if there is a
replacement device available. Unbinding of broadcast devices is not
supported as we don't want to foster that nonsense. If no replacement
device is available the unbind returns -EBUSY. Unbind is available
from the kernel and through sysfs, which is necessary to drop the
module refcount.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.499216659@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Split out selection logic

Split out the clockevent device selection logic. Preparatory patch to
allow unbinding active clockevent devices.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.431796247@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Add module refcount

We want to be able to remove clockevent modules as well. Add a
refcount so we don't remove a module with an active clock event
device.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.307435149@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Move the tick_notify() switch case to clockevents_notify()

No need to call another function and have duplicated cases.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.235746557@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Simplify locking

Now that the notifier chain is gone there are no other users and it's
pointless to nest tick_device_lock inside of clockevents_lock because
there is no other use case.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.162888472@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Get rid of the notifier chain

7+ years and still a single user. Kill it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.098520211@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Set dummy handler on CPU_DEAD shutdown

Vitaliy reported that a per cpu HPET timer interrupt crashes the
system during hibernation. What happens is that the per cpu HPET timer
gets shut down when the nonboot cpus are stopped. When the nonboot
cpus are onlined again the HPET code sets up the MSI interrupt which
fires before the clock event device is registered. The event handler
is still set to hrtimer_interrupt, which then crashes the machine due
to highres mode not being active.

See http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=700333

There is no real good way to avoid that in the HPET code. The HPET
code alrady has a mechanism to detect spurious interrupts when event
handler == NULL for a similar reason.

We can handle that in the clockevent/tick layer and replace the
previous functional handler with a dummy handler like we do in
tick_setup_new_device().

The original clockevents code did this in clockevents_exchange_device(),
but that got removed by commit 7c1e76897 (clockevents: prevent
clockevent event_handler ending up handler_noop) which forgot to fix
it up in tick_shutdown(). Same issue with the broadcast device.

Reported-by: Vitaliy Fillipov <vitalif@yourcmc.ru>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Cc: 700333@bugs.debian.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

nohz: Switch from "extended nohz" to "full nohz" based naming

"Extended nohz" was used as a naming base for the full dynticks
API and Kconfig symbols. It reflects the fact the system tries
to stop the tick in more places than just idle.

But that "extended" name is a bit opaque and vague. Rename it to
"full" makes it clearer what the system tries to do under this
config: try to shutdown the tick anytime it can. The various
constraints that prevent that to happen shouldn't be considered
as fundamental properties of this feature but rather technical
issues that may be solved in the future.

Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>

nohz: Assign timekeeping duty to a CPU outside the full dynticks range

This way the full nohz CPUs can safely run with the tick
stopped with a guarantee that somebody else is taking
care of the jiffies and GTOD progression.

Once the duty is attributed to a CPU, it won't change. Also that
CPU can't enter into dyntick idle mode or be hot unplugged.

This may later be improved from a power consumption POV. At
least we should be able to share the duty amongst all CPUs
outside the full dynticks range. Then the duty could even be
shared with full dynticks CPUs when those can't stop their
tick for any reason.

But let's start with that very simple approach first.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
[fix have_nohz_full_mask offcase]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

tick: Convert broadcast cpu bitmaps to cpumask_var_t

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130306111537.366394000@linutronix.de
Cc: Rusty Russell <rusty@rustcorp.com.au>

time: Kill xtime_lock, replacing it with jiffies_lock

Now that timekeeping is protected by its own locks, rename
the xtime_lock to jifffies_lock to better describe what it
protects.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>

clockevents: Make minimum delay adjustments configurable

The automatic increase of the min_delta_ns of a clockevents device
should be done in the clockevents code as the minimum delay is an
attribute of the clockevents device.

In addition not all architectures want the automatic adjustment, on a
massively virtualized system it can happen that the programming of a
clock event fails several times in a row because the virtual cpu has
been rescheduled quickly enough. In that case the minimum delay will
erroneously be increased with no way back. The new config symbol
GENERIC_CLOCKEVENTS_MIN_ADJUST is used to enable the automatic
adjustment. The config option is selected only for x86.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20110823133142.494157493@de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: Prevent oneshot mode when broadcast device is periodic

When the per cpu timer is marked CLOCK_EVT_FEAT_C3STOP, then we only
can switch into oneshot mode, when the backup broadcast device
supports oneshot mode as well. Otherwise we would try to switch the
broadcast device into an unsupported mode unconditionally. This went
unnoticed so far as the current available broadcast devices support
oneshot mode. Seth unearthed this problem while debugging and working
around an hpet related BIOS wreckage.

Add the necessary check to tick_is_oneshot_available().

Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1102252231200.2701@localhost6.localdomain6>
Cc: stable@kernel.org # .21 ->

time: Make do_timer() and xtime_lock local to kernel/time/

All callers of do_timer() are converted to xtime_update(). The only
users of xtime_lock are in kernel/time/. Make both local to
kernel/time/ and remove them from the global header files.

[ tglx: Reuse tick-internal.h instead of creating another local header
file. Massaged changelog ]

Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: johnstul@us.ibm.com
Cc: yong.zhang0@gmail.com
Cc: hch@infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

core: Replace __get_cpu_var with __this_cpu_read if not used for an address.

__get_cpu_var() can be replaced with this_cpu_read and will then use a
single read instruction with implied address calculation to access the
correct per cpu instance.

However, the address of a per cpu variable passed to __this_cpu_read()
cannot be determined (since it's an implied address conversion through
segment prefixes). Therefore apply this only to uses of __get_cpu_var
where the address of the variable is not used.

Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hughd@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

clockevents: Convert to raw_spinlock

Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>

clockevents: Make tick_device_lock static

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>

clockevents: prevent endless loop in tick_handle_periodic()

tick_handle_periodic() can lock up hard when a one shot clock event
device is used in combination with jiffies clocksource.

Avoid an endless loop issue by requiring that a highres valid
clocksource be installed before we call tick_periodic() in a loop when
using ONESHOT mode. The result is we will only increment jiffies once
per interrupt until a continuous hardware clocksource is available.

Without this, we can run into a endless loop, where each cycle through
the loop, jiffies is updated which increments time by tick_period or
more (due to clock steering), which can cause the event programming to
think the next event was before the newly incremented time and fail
causing tick_periodic() to be called again and the whole process loops
forever.

[ Impact: prevent hard lock up ]

Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org

hrtimers: allow the hot-unplugging of all cpus

Impact: fix CPU hotplug hang on Power6 testbox

On architectures that support offlining all cpus (at least powerpc/pseries),
hot-unpluging the tick_do_timer_cpu can result in a system hang.

This comes from the fact that if the cpu going down happens to be the
cpu doing the tick, then as the tick_do_timer_cpu handover happens after the
cpu is dead (via the CPU_DEAD notification), we're left without ticks,
jiffies are frozen and any task relying on timers (msleep, ...) is stuck.
That's particularly the case for the cpu looping in __cpu_die() waiting
for the dying cpu to be dead.

This patch addresses this by having the tick_do_timer_cpu handover happen
earlier during the CPU_DYING notification. For this, a new clockevent
notification type is introduced (CLOCK_EVT_NOTIFY_CPU_DYING) which is triggered
in hrtimer_cpu_notify().

Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

cpumask: convert kernel time functions

Impact: Use new APIs

Convert kernel/time functions to use struct cpumask *.

Note the ugly bitmap declarations in tick-broadcast.c. These should
be cpumask_var_t, but there was no obvious initialization function to
put the alloc_cpumask_var() calls in. This was safe.

(Eventually 'struct cpumask' will be undefined for CONFIG_CPUMASK_OFFSTACK,
so we use a bitmap here to show we really mean it).

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>

hrtimers: allow the hot-unplugging of all cpus

Impact: fix CPU hotplug hang on Power6 testbox

On architectures that support offlining all cpus (at least powerpc/pseries),
hot-unpluging the tick_do_timer_cpu can result in a system hang.

This comes from the fact that if the cpu going down happens to be the
cpu doing the tick, then as the tick_do_timer_cpu handover happens after the
cpu is dead (via the CPU_DEAD notification), we're left without ticks,
jiffies are frozen and any task relying on timers (msleep, ...) is stuck.
That's particularly the case for the cpu looping in __cpu_die() waiting
for the dying cpu to be dead.

This patch addresses this by having the tick_do_timer_cpu handover happen
earlier during the CPU_DYING notification. For this, a new clockevent
notification type is introduced (CLOCK_EVT_NOTIFY_CPU_DYING) which is triggered
in hrtimer_cpu_notify().

Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

cpumask: convert struct clock_event_device to cpumask pointers.

Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>

cpumask: make irq_set_affinity() take a const struct cpumask

Impact: change existing irq_chip API

Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.

Fortunately, not widely used code, but hits a few architectures.

Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?

(Folded in fix from KOSAKI Motohiro)

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>

clockevents: prevent mode mismatch on cpu online

Impact: timer hang on CPU online observed on AMD C1E systems

When a CPU is brought online then the broadcast machinery can
be in the one shot state already. Check this and setup the timer
device of the new CPU in one shot mode so the broadcast code
can pick up the next_event value correctly.

Another AMD C1E oddity, as we switch to broadcast immediately and
not after the full bring up via the ACPI cpu idle code.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: prevent cpu online to interfere with nohz

Impact: rare hang which can be triggered on CPU online.

tick_do_timer_cpu keeps track of the CPU which updates jiffies
via do_timer. The value -1 is used to signal, that currently no
CPU is doing this. There are two cases, where the variable can
have this state:

boot:
necessary for systems where the boot cpu id can be != 0

nohz long idle sleep:
When the CPU which did the jiffies update last goes into
a long idle sleep it drops the update jiffies duty so
another CPU which is not idle can pick it up and keep
jiffies going.

Using the same value for both situations is wrong, as the CPU online
code can see the -1 state when the timer of the newly onlined CPU is
setup. The setup for a newly onlined CPU goes through periodic mode
and can pick up the do_timer duty without being aware of the nohz /
highres mode of the already running system.

Use two separate states and make them constants to avoid magic
numbers confusion.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: make device shutdown robust

The device shut down does not cleanup the next_event variable of the
clock event device. So when the device is reactivated the possible
stale next_event value can prevent the device to be reprogrammed as it
claims to wait on a event already.

This is the root cause of the resurfacing suspend/resume problem,
where systems need key press to come back to life.

Fix this by setting next_event to KTIME_MAX when the device is shut
down. Use a separate function for shutdown which takes care of that
and only keep the direct set mode call in the broadcast code, where we
can not touch the next_event value.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: prevent clockevent event_handler ending up handler_noop

There is a ordering related problem with clockevents code, due to which
clockevents_register_device() called after tickless/highres switch
will not work. The new clockevent ends up with clockevents_handle_noop as
event handler, resulting in no timer activity.

The problematic path seems to be

* old device already has hrtimer_interrupt as the event_handler
* new clockevent device registers with a higher rating
* tick_check_new_device() is called
* clockevents_exchange_device() gets called
* old->event_handler is set to clockevents_handle_noop
* tick_setup_device() is called for the new device
* which sets new->event_handler using the old->event_handler which is noop.

Change the ordering so that new device inherits the proper handler.

This does not have any issue in normal case as most likely all the clockevent
devices are setup before the highres switch. But, can potentially be affecting
some corner case where HPET force detect happens after the highres switch.
This was a problem with HPET in MSI mode code that we have been experimenting
with.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

cpumask: change cpumask_of_cpu_ptr to use new cpumask_of_cpu

* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().

Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c

* Optimize various places where a pointer to the cpumask_of_cpu value
will result in reducing stack pressure.

Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

[S390] genirq/clockevents: move irq affinity prototypes/inlines to interrupt.h

> Generic code is not supposed to include irq.h. Replace this include
> by linux/hardirq.h instead and add/replace an include of linux/irq.h
> in asm header files where necessary.
> This change should only matter for architectures that make use of
> GENERIC_CLOCKEVENTS.
> Architectures in question are mips, x86, arm, sh, powerpc, uml and sparc64.
>
> I did some cross compile tests for mips, x86_64, arm, powerpc and sparc64.
> This patch fixes also build breakages caused by the include replacement in
> tick-common.h.

I generally dislike adding optional linux/* includes in asm/* includes -
I'm nervous about this causing include loops.

However, there's a separate point to be discussed here.

That is, what interfaces are expected of every architecture in the kernel.
If generic code wants to be able to set the affinity of interrupts, then
that needs to become part of the interfaces listed in linux/interrupt.h
rather than linux/irq.h.

So what I suggest is this approach instead (against Linus' tree of a
couple of days ago) - we move irq_set_affinity() and irq_can_set_affinity()
to linux/interrupt.h, change the linux/irq.h includes to linux/interrupt.h
and include asm/irq_regs.h where needed (asm/irq_regs.h is supposed to be
rarely used include since not much touches the stacked parent context
registers.)

Build tested on ARM PXA family kernels and ARM's Realview platform
kernels which both use genirq.

[ tglx@linutronix.de: add GENERIC_HARDIRQ dependencies ]

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>

clockevents: introduce force broadcast notifier

The 64bit SMP bootup is slightly different to the 32bit one. It enables
the boot CPU local APIC timer before all CPUs are brought up. Some AMD C1E
systems have the C1E feature flag only set in the secondary CPU. Due to
the early enable of the boot CPU local APIC timer the APIC timer is
registered as a fully functional device. When we detect the wreckage during
the bringup of the secondary CPU, we need to force the boot CPU into
broadcast mode.

Add a new notifier reason and implement the force broadcast in the clock
events layer.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clock events: allow replacement of broadcast timer

Change the broadcast timer, if a timer with higher rating becomes available.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

clockevents: fix resume logic

We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.

Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.

Fixup the existing users.

Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.

[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

highres/dyntick: prevent xtime lock contention

While the !highres/!dyntick code assigns the duty of the do_timer() call to
one specific CPU, this was dropped in the highres/dyntick part during
development.

Steven Rostedt discovered the xtime lock contention on highres/dyntick due
to several CPUs trying to update jiffies.

Add the single CPU assignement back. In the dyntick case this needs to be
handled carefully, as the CPU which has the do_timer() duty must drop the
assignement and let it be grabbed by another CPU, which is active.
Otherwise the do_timer() calls would not happen during the long sleep.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Mark Lord <mlord@pobox.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[PATCH] clockevents: Fix suspend/resume to disk hangs

I finally found a dual core box, which survives suspend/resume without
crashing in the middle of nowhere. Sigh, I never figured out from the
code and the bug reports what's going on.

The observed hangs are caused by a stale state transition of the clock
event devices, which keeps the RCU synchronization away from completion,
when the non boot CPU is brought back up.

The suspend/resume in oneshot mode needs the similar care as the
periodic mode during suspend to RAM. My assumption that the state
transitions during the different shutdown/bringups of s2disk would go
through the periodic boot phase and then switch over to highres resp.
nohz mode were simply wrong.

Add the appropriate suspend / resume handling for the non periodic
modes.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[PATCH] Save/restore periodic tick information over suspend/resume

The programming of periodic tick devices needs to be saved/restored
across suspend/resume - otherwise we might end up with a system coming
up that relies on getting a PIT (or HPET) interrupt, while those devices
default to 'no interrupts' after powerup. (To confuse things it worked
to a certain degree on some systems because the lapic gets initialized
as a side-effect of SMP bootup.)

This suspend / resume thing was dropped unintentionally during the
last-minute -mm code reshuffling.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[TICK] tick-common: Fix one-shot handling in tick_handle_periodic().

When clockevents_program_event() is given an expire time in the
past, it does not update dev->next_event, so this looping code
would loop forever once the first in-the-past expiration time
was used.

Keep advancing "next" locally to fix this bug.

Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] Add debugging feature /proc/timer_list

add /proc/timer_list, which prints all currently pending (high-res) timers,
all clock-event sources and their parameters in a human-readable form.

Sample output:

Timer List Version: v0.1
HRTIMER_MAX_CLOCK_BASES: 2
now at 4246046273872 nsecs

cpu: 0
clock 0:
.index: 0
.resolution: 1 nsecs
.get_time: ktime_get_real
.offset: 1273998312645738432 nsecs
active timers:
clock 1:
.index: 1
.resolution: 1 nsecs
.get_time: ktime_get
.offset: 0 nsecs
active timers:
#0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_stop_sched_tick, swapper/0
# expires at 4246432689566 nsecs [in 386415694 nsecs]
#1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, pcscd/2050
# expires at 4247018194689 nsecs [in 971920817 nsecs]
#2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, irqbalance/1909
# expires at 4247351358392 nsecs [in 1305084520 nsecs]
#3: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, crond/2157
# expires at 4249097614968 nsecs [in 3051341096 nsecs]
#4: <f5a90ec8>, it_real_fn, do_setitimer, syslogd/1888
# expires at 4251329900926 nsecs [in 5283627054 nsecs]
.expires_next : 4246432689566 nsecs
.hres_active : 1
.check_clocks : 0
.nr_events : 31306
.idle_tick : 4246020791890 nsecs
.tick_stopped : 1
.idle_jiffies : 986504
.idle_calls : 40700
.idle_sleeps : 36014
.idle_entrytime : 4246019418883 nsecs
.idle_sleeptime : 4178181972709 nsecs

cpu: 1
clock 0:
.index: 0
.resolution: 1 nsecs
.get_time: ktime_get_real
.offset: 1273998312645738432 nsecs
active timers:
clock 1:
.index: 1
.resolution: 1 nsecs
.get_time: ktime_get
.offset: 0 nsecs
active timers:
#0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_restart_sched_tick, swapper/0
# expires at 4246050084568 nsecs [in 3810696 nsecs]
#1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, atd/2227
# expires at 4261010635003 nsecs [in 14964361131 nsecs]
#2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, smartd/2332
# expires at 5469485798970 nsecs [in 1223439525098 nsecs]
.expires_next : 4246050084568 nsecs
.hres_active : 1
.check_clocks : 0
.nr_events : 24043
.idle_tick : 4246046084568 nsecs
.tick_stopped : 0
.idle_jiffies : 986510
.idle_calls : 26360
.idle_sleeps : 22551
.idle_entrytime : 4246043874339 nsecs
.idle_sleeptime : 4170763761184 nsecs

tick_broadcast_mask: 00000003
event_broadcast_mask: 00000001

CPU#0's local event device:

Clock Event Device: lapic
capabilities: 0000000e
max_delta_ns: 807385544
min_delta_ns: 1443
mult: 44624025
shift: 32
set_next_event: lapic_next_event
set_mode: lapic_timer_setup
event_handler: hrtimer_interrupt
.installed: 1
.expires: 4246432689566 nsecs

CPU#1's local event device:

Clock Event Device: lapic
capabilities: 0000000e
max_delta_ns: 807385544
min_delta_ns: 1443
mult: 44624025
shift: 32
set_next_event: lapic_next_event
set_mode: lapic_timer_setup
event_handler: hrtimer_interrupt
.installed: 1
.expires: 4246050084568 nsecs

Clock Event Device: hpet
capabilities: 00000007
max_delta_ns: 2147483647
min_delta_ns: 3352
mult: 61496110
shift: 32
set_next_event: hpet_next_event
set_mode: hpet_set_mode
event_handler: handle_nextevt_broadcast

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[PATCH] tick-management: dyntick / highres functionality

With Ingo Molnar <mingo@elte.hu>

Add functions to provide dynamic ticks and high resolution timers. The code
which keeps track of jiffies and handles the long idle periods is shared
between tick based and high resolution timer based dynticks. The dyntick
functionality can be disabled on the kernel commandline. Provide also the
infrastructure to support high resolution timers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[PATCH] tick-management: broadcast functionality

With Ingo Molnar <mingo@elte.hu>

Add broadcast functionality, so per cpu clock event devices can be registered
as dummy devices or switched from/to broadcast on demand. The broadcast
function distributes the events via the broadcast function of the clock event
device. This is primarily designed to replace the switch apic timer to / from
IPI in power states, where the apic stops.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[PATCH] tick-management: core functionality

With Ingo Molnar <mingo@elte.hu>

The tick-management code is the first user of the clockevents layer. It takes
clock event devices from the clock events core and uses them to provide the
periodic tick.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>