soc: qcom: rpmh: Remove serialization of TCS commands

Requests sent to RPMH can be sent as fire-n-forget or response required,
with the latter ensuring the command has been completed by the hardware
accelerator. Commands in a request with tcs_cmd::wait set, would ensure
that those select commands are sent as response required, even though
the actual TCS request may be fire-n-forget.

Also, commands with .wait flag were also guaranteed to be complete
before the following command in the TCS is sent. This means that the
next command of the same request blocked until the current request is
completed. This could mean waiting for a voltage to settle or series of
NOCs be configured before the next command is sent. But drivers using
this feature have never cared about the serialization aspect. By not
enforcing the serialization we can allow the hardware to run in parallel
improving the performance.

Let's clarify the usage of this member in the tcs_cmd structure to mean
only completion and not serialization. This should also improve the
performance of bus requests where changes could happen in parallel.
Also, CPU resume from deep idle may see benefits from certain wake
requests.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1610008770-13891-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

drivers: qcom: Add BCM vote macro to header

The macro to generate a Bus Controller Manager (BCM) TCS command is used
by the interconnect driver but might also be interesting to other
drivers that need to construct TCS commands for sub processors so move
it out of the sdm845 specific file and into the header.

Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>

drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs

Add controller driver for QCOM SoCs that have hardware based shared
resource management. The hardware IP known as RSC (Resource State
Coordinator) houses multiple Direct Resource Voter (DRV) for different
execution levels. A DRV is a unique voter on the state of a shared
resource. A Trigger Control Set (TCS) is a bunch of slots that can house
multiple resource state requests, that when triggered will issue those
requests through an internal bus to the Resource Power Manager Hardened
(RPMH) blocks. These hardware blocks are capable of adjusting clocks,
voltages, etc. The resource state request from a DRV are aggregated
along with state requests from other processors in the SoC and the
aggregate value is applied on the resource.

Some important aspects of the RPMH communication -
- Requests are <addr, value> with some header information
- Multiple requests (upto 16) may be sent through a TCS, at a time
- Requests in a TCS are sent in sequence
- Requests may be fire-n-forget or completion (response expected)
- Multiple TCS from the same DRV may be triggered simultaneously
- Cannot send a request if another request for the same addr is in
progress from the same DRV
- When all the requests from a TCS are complete, an IRQ is raised
- The IRQ handler needs to clear the TCS before it is available for
reuse
- TCS configuration is specific to a DRV
- Platform drivers may use DRV from different RSCs to make requests

Resource state requests made when CPUs are active are called 'active'
state requests. Requests made when all the CPUs are powered down (idle
state) are called 'sleep' state requests. They are matched by a
corresponding 'wake' state requests which puts the resources back in to
previously requested active state before resuming any CPU. TCSes are
dedicated for each type of requests. Active mode TCSes (AMC) are used to
send requests immediately to the resource, while control TCS are used to
provide specific information to the controller. Sleep and Wake TCS send
sleep and wake requests, after and before the system halt respectively.

Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>