sctp: move 198 addresses from unusable to private scope

The doc draft-stewart-tsvwg-sctp-ipv4-00 that restricts 198 addresses
was never published. These addresses as private addresses should be
allowed to use in SCTP.

As Michael Tuexen suggested, this patch is to move 198 addresses from
unusable to private scope.

Reported-by: Sérgio <surkamp@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add the probe timer in transport for PLPMTUD

There are 3 timers described in rfc8899#section-5.1.1:

PROBE_TIMER, PMTU_RAISE_TIMER, CONFIRMATION_TIMER

This patches adds a 'probe_timer' in transport, and it works as either
PROBE_TIMER or PMTU_RAISE_TIMER. At most time, it works as PROBE_TIMER
and expires every a 'probe_interval' time to send the HB probe packet.
When transport pl enters COMPLETE state, it works as PMTU_RAISE_TIMER
and expires in 'probe_interval * 30' time to go back to SEARCH state
and do searching again.

SCTP HB is an acknowledged packet, CONFIRMATION_TIMER is not needed.

The timer will start when transport pl enters BASE state and stop
when it enters DISABLED state.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add the constants/variables and states and some APIs for transport

These are 4 constants described in rfc8899#section-5.1.2:

MAX_PROBES, MIN_PLPMTU, MAX_PLPMTU, BASE_PLPMTU;

And 2 variables described in rfc8899#section-5.1.3:

PROBED_SIZE, PROBE_COUNT;

And 5 states described in rfc8899#section-5.2:

DISABLED, BASE, SEARCH, SEARCH_COMPLETE, ERROR;

And these 4 APIs are used to reset/update PLPMTUD, check if PLPMTUD is
enabled, and calculate the additional headers length for a transport.

Note the member 'probe_high' in transport will be set to the probe
size when a probe fails with this probe size in the next patches.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add probe_interval in sysctl and sock/asoc/transport

PLPMTUD can be enabled by doing 'sysctl -w net.sctp.probe_interval=n'.
'n' is the interval for PLPMTUD probe timer in milliseconds, and it
can't be less than 5000 if it's not 0.

All asoc/transport's PLPMTUD in a new socket will be enabled by default.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: create udp4 sock and add its encap_rcv

This patch is to add the functions to create/release udp4 sock,
and set the sock's encap_rcv to process the incoming udp encap
sctp packets. In sctp_udp_rcv(), as we can see, all we need to
do is fix the transport header for sctp_rcv(), then it would
implement the part of rfc6951#section-5.4:

"When an encapsulated packet is received, the UDP header is removed.
Then, the generic lookup is performed, as done by an SCTP stack
whenever a packet is received, to find the association for the
received SCTP packet"

Note that these functions will be called in the last patch of
this patchset when enabling this feature.

v1->v2:
- Add pr_err() when fails to create udp v4 sock.
v2->v3:
- Add 'select NET_UDP_TUNNEL' in sctp Kconfig.
v3->v4:
- No change.
v4->v5:
- Change to set udp_port to 0 by default.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sctp: Don't advertise IPv4 addresses if ipv6only is set on the socket

If a socket is set ipv6only, it will still send IPv4 addresses in the
INIT and INIT_ACK packets. This potentially misleads the peer into using
them, which then would cause association termination.

The fix is to not add IPv4 addresses to ipv6only sockets.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add support for Primary Path Switchover

This is a new feature defined in section 5 of rfc7829: "Primary Path
Switchover". By introducing a new tunable parameter:

Primary.Switchover.Max.Retrans (PSMR)

The primary path will be changed to another active path when the path
error counter on the old primary path exceeds PSMR, so that "the SCTP
sender is allowed to continue data transmission on a new working path
even when the old primary destination address becomes active again".

This patch is to add this tunable parameter, 'ps_retrans' per netns,
sock, asoc and transport. It also allows a user to change ps_retrans
per netns by sysctl, and ps_retrans per sock/asoc/transport will be
initialized with it.

The check will be done in sctp_do_8_2_transport_strike() when this
feature is enabled.

Note this feature is disabled by initializing 'ps_retrans' per netns
as 0xffff by default, and its value can't be less than 'pf_retrans'
when changing by sysctl.

v3->v4:
- add define SCTP_PS_RETRANS_MAX 0xffff, and use it on extra2 of
sysctl 'ps_retrans'.
- add a new entry for ps_retrans on ip-sysctl.txt.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add pf_expose per netns and sock and asoc

As said in rfc7829, section 3, point 12:

The SCTP stack SHOULD expose the PF state of its destination
addresses to the ULP as well as provide the means to notify the
ULP of state transitions of its destination addresses from
active to PF, and vice versa. However, it is recommended that
an SCTP stack implementing SCTP-PF also allows for the ULP to be
kept ignorant of the PF state of its destinations and the
associated state transitions, thus allowing for retention of the
simpler state transition model of [RFC4960] in the ULP.

Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.

So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.

It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.

Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.

v1->v2:
- Fix a build warning noticed by Nathan Chancellor.
v2->v3:
- set pf_expose to UNUSED by default to keep compatible with old
applications.
v3->v4:
- add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
- change this patch to 1/5, and move sctp_assoc_control_transport
change into 2/5, as Marcelo suggested.
- use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104

Based on 1 normalized pattern(s):

this sctp implementation is free software you can redistribute it
and or modify it under the terms of the gnu general public license
as published by the free software foundation either version 2 or at
your option any later version this sctp implementation is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with gnu cc see the file copying if not see
http www gnu org licenses

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 42 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.683323110@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: rename enum sctp_event to sctp_event_type

sctp_event is a structure name defined in RFC for sockopt
SCTP_EVENT. To avoid the conflict, rename it.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: count both sk and asoc sndbuf with skb truesize and sctp_chunk size

Now it's confusing that asoc sndbuf_used is doing memory accounting with
SCTP_DATA_SNDSIZE(chunk) + sizeof(sk_buff) + sizeof(sctp_chunk) while sk
sk_wmem_alloc is doing that with skb->truesize + sizeof(sctp_chunk).

It also causes sctp_prsctp_prune to count with a wrong freed memory when
sndbuf_policy is not set.

To make this right and also keep consistent between asoc sndbuf_used, sk
sk_wmem_alloc and sk_wmem_queued, use skb->truesize + sizeof(sctp_chunk)
for them.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove old and unused SCTP_MIN_PMTU

This value is not used anywhere in the code. In essence it is a
duplicate of SCTP_DEFAULT_MINSEGMENT, which is used by the stack.

SCTP_MIN_PMTU value makes more sense, but we should not change to it now
as it would risk breaking applications.

So this patch removes SCTP_MIN_PMTU and adjust the comment above it.

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: implement assign_number for sctp_stream_interleave

assign_number is added as a member of sctp_stream_interleave, used
to assign ssn for data or mid (message id) for idata, called in
sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is,
and sctp_chunk_assign_mid is added for sctp_stream_interleave_1.

This procedure is described in section 2.2.2 of RFC8260.

All sizeof(struct sctp_data_chunk) in tx path is replaced with
sctp_datachk_len, to make it right for idata as well. And also
adjust sctp_chunk_is_data for SCTP_CID_I_DATA.

After this patch, idata can be built and sent in tx path.

Note that if sp strm_interleave is set, it has to wait_connect in
sctp_sendmsg, as asoc intl_enable need to be known after 4 shake-
hands, to decide if it should use data or idata later. data and
idata can't be mixed to send in one asoc.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_subtype_t

This patch is to remove the typedef sctp_subtype_t, and
replace with union sctp_subtype in the places where it's
using this typedef.

Note that it doesn't fix many indents although it should,
as sctp_disposition_t's removal would mess them up again.
So better to fix them when removing sctp_disposition_t in
later patch.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_event_t

This patch is to remove the typedef sctp_event_t, and
replace with enum sctp_event in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_event_timeout_t

This patch is to remove the typedef sctp_event_timeout_t, and
replace with enum sctp_event_timeout in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_event_other_t

This patch is to remove the typedef sctp_event_other_t, and
replace with enum sctp_event_other in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_event_primitive_t

This patch is to remove the typedef sctp_event_primitive_t, and
replace with enum sctp_event_primitive in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_state_t

This patch is to remove the typedef sctp_state_t, and
replace with enum sctp_state in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_ierror_t

This patch is to remove the typedef sctp_ierror_t, and
replace with enum sctp_ierror in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_xmit_t

This patch is to remove the typedef sctp_xmit_t, and
replace with enum sctp_xmit in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_sock_state_t

This patch is to remove the typedef sctp_sock_state_t, and
replace with enum sctp_sock_state in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_transport_cmd_t

This patch is to remove the typedef sctp_transport_cmd_t, and
replace with enum sctp_transport_cmd in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_scope_t

This patch is to remove the typedef sctp_scope_t, and
replace with enum sctp_scope in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_scope_policy_t

This patch is to remove the typedef sctp_scope_policy_t and keep
it's members as an anonymous enum.

It is also to define SCTP_SCOPE_POLICY_MAX to replace the num 3
in sysctl.c to make codes clear.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_retransmit_reason_t

This patch is to remove the typedef sctp_retransmit_reason_t, and
replace with enum sctp_retransmit_reason in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_lower_cwnd_t

This patch is to remove the typedef sctp_lower_cwnd_t, and
replace with enum sctp_lower_cwnd in the places where it's
using this typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_data_chunk_t

This patch is to remove the typedef sctp_data_chunk_t, and replace
with struct sctp_data_chunk in the places where it's using this
typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the typedef sctp_cid_t

This patch is to remove the typedef sctp_cid_t, and replace
with struct sctp_cid in the places where it's using this
typedef.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add reconf chunk event

This patch is to add reconf chunk event based on the sctp event
frame in rx path, it will call sctp_sf_do_reconf to process the
reconf chunk.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add stream reconf primitive

This patch is to add a primitive based on sctp primitive frame for
sending stream reconf request. It works as the other primitives,
and create a SCTP_CMD_REPLY command to send the request chunk out.

sctp_primitive_RECONF would be the api to send a reconf request
chunk.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add stream reconf timer

This patch is to add a per transport timer based on sctp timer frame
for stream reconf chunk retransmission. It would start after sending
a reconf request chunk, and stop after receiving the response chunk.

If the timer expires, besides retransmitting the reconf request chunk,
it would also do the same thing with data RTO timer. like to increase
the appropriate error counts, and perform threshold management, possibly
destroying the asoc if sctp retransmission thresholds are exceeded, just
as section 5.1.1 describes.

This patch is also to add asoc strreset_chunk, it is used to save the
reconf request chunk, so that it can be retransmitted, and to check if
the response is really for this request by comparing the information
inside with the response chunk as well.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: change to use TCP_CLOSE_WAIT as SCTP_SS_CLOSING

Prior to this patch, sctp defined TCP_CLOSING as SCTP_SS_CLOSING.
TCP_CLOSING is such a special sk state in TCP that inet common codes
even exclude it.

For instance, inet_accept thinks the accept sk's state never be
TCP_CLOSING, or it will give a WARN_ON. TCP works well with that
while SCTP may trigger the call trace, as CLOSING state in SCTP
has different meaning from TCP.

This fix is to change to use TCP_CLOSE_WAIT as SCTP_SS_CLOSING,
instead of TCP_CLOSING. Some side-effects could be expected,
regardless of not being used before. inet_accept will accept it
now.

I did all the func_tests in lksctp-tools and ran sctp codnomicon
fuzzer tests against this patch, no regression or failure found.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: Rename SCTP_XMIT_NAGLE_DELAY to SCTP_XMIT_DELAY

MSG_MORE and 'corking' a socket would require that the transmit of
a data chunk be delayed.
Rename the return value to be less specific.

Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

include/net/: Fix FSF address in file headers

Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: trivial: update bug report in header comment

With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: trivial: update mailing list address

The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: introduce uapi header for sctp

This patch introduces an UAPI header for the SCTP protocol,
so that we can facilitate the maintenance and development of
user land applications or libraries, in particular in terms
of header synchronization.

To not break compatibility, some fragments from lksctp-tools'
netinet/sctp.h have been carefully included, while taking care
that neither kernel nor user land breaks, so both compile fine
with this change (for lksctp-tools I tested with the old
netinet/sctp.h header and with a newly adapted one that includes
the uapi sctp header). lksctp-tools smoke test run through
successfully as well in both cases.

Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: remove unused multiple cookie keys

Vlad says: The whole multiple cookie keys code is completely unused
and has been all this time. Noone uses anything other then the
secret_key[0] since there is no changeover support anywhere.

Thus, for now clean up its left-over fragments.

Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Make hmac algorithm selection for cookie generation dynamic

Currently sctp allows for the optional use of md5 of sha1 hmac algorithms to
generate cookie values when establishing new connections via two build time
config options. Theres no real reason to make this a static selection. We can
add a sysctl that allows for the dynamic selection of these algorithms at run
time, with the default value determined by the corresponding crypto library
availability.
This comes in handy when, for example running a system in FIPS mode, where use
of md5 is disallowed, but SHA1 is permitted.

Note: This new sysctl has no corresponding socket option to select the cookie
hmac algorithm. I chose not to implement that intentionally, as RFC 6458
contains no option for this value, and I opted not to pollute the socket option
namespace.

Change notes:
v2)
* Updated subject to have the proper sctp prefix as per Dave M.
* Replaced deafult selection options with new options that allow
developers to explicitly select available hmac algs at build time
as per suggestion by Vlad Y.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Implement quick failover draft from tsvwg

I've seen several attempts recently made to do quick failover of sctp transports
by reducing various retransmit timers and counters. While its possible to
implement a faster failover on multihomed sctp associations, its not
particularly robust, in that it can lead to unneeded retransmits, as well as
false connection failures due to intermittent latency on a network.

Instead, lets implement the new ietf quick failover draft found here:
http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05

This will let the sctp stack identify transports that have had a small number of
errors, and avoid using them quickly until their reliability can be
re-established. I've tested this out on two virt guests connected via multiple
isolated virt networks and believe its in compliance with the above draft and
works well.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
CC: joe@perches.com
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove completely unsed EMPTY state

SCTP does not SCTP_STATE_EMPTY and we can never be in
that state. Remove useless code.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: delete unused macro definition of sctp_chunk_is_control

The macro never be used.
And if needed, can use !sctp_chunk_is_data instead of.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: kill unused macro definition

These macros have been existed for several years since v2.6.12-rc2.
But they never be used. So remove them now.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Update SWS avaoidance receiver side algorithm

We currently send window update SACKs every time we free up 1 PMTU
worth of data. That a lot more SACKs then necessary. Instead, we'll
now send back the actuall window every time we send a sack, and do
window-update SACKs when a fraction of the receive buffer has been
opened. The fraction is controlled with a sysctl.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: Sysctl configuration for IPv4 Address Scoping

This patch introduces a new sysctl option to make IPv4 Address Scoping
configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>.

In networking environments where DNAT rules in iptables prerouting
chains convert destination IP's to link-local/private IP addresses,
SCTP connections fail to establish as the INIT chunk is dropped by the
kernel due to address scope match failure.
For example to support overlapping IP addresses (same IP address with
different vlan id) a Layer-5 application listens on link local IP's,
and there is a DNAT rule that maps the destination IP to a link local
IP. Such applications never get the SCTP INIT if the address-scoping
draft is strictly followed.

This sysctl configuration allows SCTP to function in such
unconventional networking environments.

Sysctl options:
0 - Disable IPv4 address scoping draft altogether
1 - Enable IPv4 address scoping (default, current behavior)
2 - Enable address scoping but allow IPv4 private addresses in init/init-ack
3 - Enable address scoping but allow IPv4 link local address in init/init-ack

Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: Disallow new connection on a closing socket

If a socket has a lot of association that are in the process of
of being closed/aborted, it is possible for a remote to establish
new associations during the time period that the old ones are shutting
down. If this was a result of a close() call, there will be no socket
and will cause a memory leak. We'll prevent this by setting the
socket state to CLOSING and disallow new associations when in this state.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

net: mark read-only arrays as const

String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Rework the tsn map to use generic bitmap.

The tsn map currently use is 4K large and is stuck inside
the sctp_association structure making memory references REALLY
expensive. What we really need is at most 4K worth of bits
so the biggest map we would have is 512 bytes. Also, the
map is only really usefull when we have gaps to store and
report. As such, starting with minimal map of say 32 TSNs (bits)
should be enough for normal low-loss operations. We can grow
the map by some multiple of 32 along with some extra room any
time we receive the TSN which would put us outside of the map
boundry. As we close gaps, we can shift the map to rebase
it on the latest TSN we've seen. This saves 4088 bytes per
association just in the map alone along savings from the now
unnecessary structure members.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Stop claiming that this is a "reference implementation"

I was notified by Randy Stewart that lksctp claims to be
"the reference implementation". First of all, "the
refrence implementation" was the original implementation
of SCTP in usersapce written ty Randy and a few others.
Second, after looking at the definiton of 'reference implementation',
we don't really meet the requirements.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

[IPV4] sctp: Use ipv4_is_<type>

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP: Fix build issues with SCTP AUTH.

SCTP-AUTH requires selection of CRYPTO, HMAC and SHA1 since
SHA1 is a MUST requirement for AUTH. We also support SHA256,
but that's optional, so fix the code to treat it as such.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

SCTP: Make sctp_verify_param return multiple indications.

SCTP-AUTH and future ADD-IP updates have a requirement to
do additional verification of parameters and an ability to
ABORT the association if verification fails. So, introduce
additional return code so that we can clear signal a required
action.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

SCTP: Fix difference cases of retransmit.

Commit d0ce92910bc04e107b2f3f2048f07e94f570035d broke several retransmit
cases including fast retransmit. The reason is that we should
only delay by rto while doing retranmists as a result of a timeout.
Retransmit as a result of path mtu discover, fast retransmit, or
other evernts that should trigger immidiate retransmissions got broken.

Also, since rto is doubled prior to marking of packets elegable for
retransmission, we never marked correct chunks anyway.

The fix is provide a reason for a given retransmission so that we
can mark chunks appropriately and to save the old rto value to do
comparisons against.

All regressions tests passed with this code.

Spotted by Wei Yongjun <yjwei@cn.fujitsu.com>

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

[SCTP]: Implement the receive and verification of AUTH chunk

This patch implements the receive path needed to process authenticated
chunks. Add ability to process the AUTH chunk and handle edge cases
for authenticated COOKIE-ECHO as well.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Implement SCTP-AUTH internals

This patch implements the internals operations of the AUTH, such as
key computation and storage. It also adds necessary variables to
the SCTP data structures.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Implement SCTP_MAX_BURST socket option.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Trivial sctp endianness annotations.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Remove multiple levels of msecs to jiffies conversions.

The SCTP sysctl entries are displayed in milliseconds, but stored
internally in jiffies. This results in multiple levels of msecs to
jiffies conversion and as a result produces a truncation error. This
patch makes things consistent in that we store and display defaults
in milliseconds and only convert once for use by association.
This patch also adds some sane min/max values so that we don't go off
the deep end.

Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Use HMAC template and hash interface

This patch converts SCTP to use the new HMAC template and hash interface.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TCP]: Move the tcp sock states to net/tcp_states.h

Lots of places just needs the states, not even linux/tcp.h, where this
enum was, needs it.

This speeds up development of the refactorings as less sources are
rebuilt when things get moved from net/tcp.h.

Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP] Make init & delayed sack timeouts configurable by user.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP] sctp_connectx() API support

Implements sctp_connectx() as defined in the SCTP sockets API draft by
tunneling the request through a setsockopt().

Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!