platform/x86/siemens: simatic-ipc: add new models BX-56A/BX-59A

This adds support for the Siemens Simatic IPC models BX-56A/BX-59A,
led/watchdog/battery on these models are same, actual drivers for
models will be sent in separate patches.

Signed-off-by: xingtong.wu <xingtong.wu@siemens.com>
Link: https://lore.kernel.org/r/20230731071424.4663-2-xingtong_wu@163.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: simatic-ipc: add CMOS battery monitoring

Siemens Simatic Industrial PCs can monitor the voltage of the CMOS
battery with two bits that indicate low or empty state. This can be GPIO
or PortIO based.
Here we model that as a hwmon voltage. The core driver does the PortIO
and provides boilerplate for the GPIO versions. Which are split out to
model runtime dependencies while allowing fine-grained kernel
configuration.

Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230706154831.19100-3-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: simatic-ipc: add another model BX-21A

This adds support for the Siemens Simatic IPC model BX-21A. Actual
drivers for that model will be sent in separate patches.

Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230713115639.16419-2-henning.schild@siemens.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

leds: simatic-ipc-leds-gpio: add new model 227G

This adds support of the Siemens Simatic IPC227G. Its LEDs are connected
to GPIO pins provided by the gpio-f7188x module. We make sure that
gets loaded, if not enabled in the kernel config no LED support will be
available.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20220825104422.14156-6-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: simatic-ipc: drop custom P2SB bar code

The two drivers that used to use this have been switched over to the
common P2SB accessor, so this code is not needed any longer.

Signed-off-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>

platform/x86: simatic-ipc: add main driver for Siemens devices

This mainly implements detection of these devices and will allow
secondary drivers to work on such machines.

The identification is DMI-based with a vendor specific way to tell them
apart in a reliable way.

Drivers for LEDs and Watchdogs will follow to make use of that platform
detection.

There is also some code to allow secondary drivers to find GPIO memory,
that needs to be in place because the pinctrl drivers do not come up.

Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20211213120502.20661-2-henning.schild@siemens.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>