iio: Comment that the LSM303D also has the Magnetometer DRDY

Per its datasheet, the LSM303D also features that pin.

Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-6-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: st_magn: Provide default platform data

Provide default platform data for magnetometer in case it supports DRDY.

One case is LSM9DS0 IMU, on which it is the case. Since accelerometer
is using INT1, default magnetometer to INT2.

While at it, update description of the drdy_int_pin field.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210414195454.84183-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: add wakeup_source in st_sensors_platform_data

Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 177

Based on 1 normalized pattern(s):

licensed under the gpl 2

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 135 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: imu: st_lsm6dsx: add i2c embedded controller support

i2c controller embedded in lsm6dx series can connect up to four
slave devices using accelerometer sensor as trigger for i2c
read/write operations.
Introduce sensor hub support for lsm6dso sensor. Add register map
for lis2mdl magnetometer sensor.
In order to perform single read/write operations st_lsm6dsx driver
relies on SLV0 channel (hw FIFO is not supported yet)

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: st_accel: add SPI-3wire support

Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration

Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.

Fixes: ddc05fa28606 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: support open drain mode

Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.

If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).

Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Added ST-sensors platform data to select the DRDY interrupt pin

This patch add support to redirect the DRDY interrupt on INT1 or INT2
on accelerometer and pressure sensors.

Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>