dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM

Tegra210 QSPI clock output has divider DIV2_SEL which will be enabled
when using DDR interface mode.

This patch adds clock ID for this to dt-binding.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM

Tegra210 QSPI clock output has divider DIV2_SEL which will be enabled
when using DDR interface mode.

This patch adds clock ID for this to dt-binding.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add PLLP_UD and PLLMB_UD for Tegra210

Introduce the low jitter path of PLLP and PLLMB which can be used as EMC
clock source.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

dt-bindings: clock: tegra: Add clock ID for CSI TPG clock

Tegra210 uses PLLD out internally for CSI TPG. This patch adds a clock
ID for this CSI TPG clock from PLLD.

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

dt-bindings: clock: tegra: Remove PMC clock IDs

clk_out_1, clk_out_2, clk_out_3, blink are part of Tegra PMC block so
these clocks should be provided by the Tegra PMC. IDs for these clocks
have been defined in dt-bindings/soc/tegra-pmc.h.

This patch removes the IDs for these clocks from the Tegra clock device
tree bindings.

Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

dt-bindings: clock: tegra: Add IDs for OSC clocks

Tegra has OSC, OSC_DIV2 and OSC_DIV4 clocks from OSC pads which are
the possible parents of Tegra PMC clocks clk_out_1, clk_out_2, and
clk_out_3 for Tegra30 through Tegra210.

So, this patch adds ids for these clocks.

Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Reimplement SOR clocks on Tegra210

In order to allow the display driver to deal uniformly with all SOR
generations, implement the SOR clocks in a way that is compatible with
Tegra186 and later.

Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Remove last remains of TEGRA210_CLK_SOR1_SRC

Later SoC generations implement this clock as SOR1_OUT. For consistency,
the Tegra210 implementation was adapted to match the same name in commit
4d1dc4018573 ("dt-bindings: clock: tegra: Add sor1_out clock").

Clean up the remaining pieces by adopting the new name for the internal
identifiers and remove the old alias. Note that since both SOR1_SRC and
SOR1_OUT were referring to the same device tree clock ID, this does not
break device tree ABI.

Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

dt-bindings: clock: tegra: Rename SOR0_LVDS to SOR0_OUT

Tegra186 and later call this clock SOR0_OUT. Rename it on Tegra124 and
Tegra210 to make the names consistent.

Keep the old name for now to keep device trees buildable until they have
all been converted.

Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add la clock for Tegra210

This clock is needed by the memory built-in self test work around.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: clock: tegra: Add sor1_out clock

The sor1_src clock implemented on Tegra210 is modelled the wrong way
around, which causes some issues with HDMI and DP support. This clock
implementation is provided by BPMP on Tegra186, which models this in
a more correct way. Since this introduces incompatibilities between
the two SoC generations which we want to avoid, the Tegra210 will be
fixed in subsequent patches.

This change adds sor1_out as an alias for sor1_src.

Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add missing Tegra210 clocks

iqc1, iqc2, tegra_clk_pll_a_out_adsp, tegra_clk_pll_a_out0_out_adsp, adsp
and adsp neon were not modelled. dp2 wasn't modelled for Tegra210.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add aclk

This clock clocks the ADSP Cortex-A9.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Define Tegra210 DMIC sync clocks

Tegra210 has 3 DMIC inputs which can be clocked from the recovered clock
of several other audio inputs (eg. i2s0, i2s1, ...). To model this, we
add a 3 new clocks similar to the audio* clocks which handle the same
function for the I2S and SPDIF clocks.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add CEC clock

This clock is used to clock the HDMI CEC interface.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Fix ISP clock modelling

The 2 ISP clocks (ispa and ispb) share a mux/divider control. So model
this as 1 mux/divider clock and child gate clocks.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Enable sor1 and sor1_src on Tegra210

Make the sor1 and sor1_src clocks available on Tegra210. They will be
used by the display driver to support HDMI and DP.

Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Fix pllre Tegra210 and add pll_re_out1

Use a new Tegra210 version of the pll_register_pllre function to
allow setting the proper settings for the m and n div fields.

Additionally define PLL_RE_OUT1 on Tegra210.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: define PLLRE_OUT1 register offset]
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add the APB2APE audio clock on Tegra210

The APB2APE clock for the audio subsystem is required for powering up the
audio power domain and accessing the various modules in this subsystem on
Tegra210 devices. Add this clock for Tegra210.

Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

clk: tegra: Add Tegra210 device tree binding

Add a header file that defines the clock numbers for Tegra210. It is
meant to be included by device trees so that they can refer to the
clocks by symbolic name instead of numeric value.

Also add the device tree binding documentation which is largely the
same as for earlier generations of Tegra.

Extracted from a larger patch by Rhyland Klein <rklein@nvidia.com>.

Signed-off-by: Thierry Reding <treding@nvidia.com>