watchdog/hpwdt: Support Suspend and Resume

Add call backs to support suspend and resume.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240214164941.630775-2-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Remove unused variable

Remove the unused variable ilo5.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213215340.495734-4-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Remove redundant test.

ProLiants of vintage to have an iLO 5, no longer send watchdog NMI
as an IO CHECK. They are presented to hpwdt_pretimeout as NMI_UNKNOWN.
The preceding if statement rejects if !mynmi irrespective of value
of pretimeout making this if statement redundant.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213215340.495734-3-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Only claim UNKNOWN NMI if from iLO

Avoid unnecessary crashes by claiming only NMIs that are due to
ERROR signalling or generated by the hpwdt hardware device.

The code does this, but only for iLO5.

The intent was to preserve legacy, Gen9 and earlier, semantics of
using hpwdt for error containtment as hardware/firmware would signal
fatal IO errors as an NMI with the expectation of hpwdt crashing
the system. Howerver, these IO errors should be received by hpwdt
as an NMI_IO_CHECK. So the test is overly permissive and should
not be limited to only ilo5.

We need to enable this protection for future iLOs not matching the
current PCI IDs.

Fixes: 62290a5c194b ("watchdog: hpwdt: Claim NMIs generated by iLO5")
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213215340.495734-2-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Include nmi.h only if CONFIG_HPWDT_NMI_DECODING

Fixes: d48b0e173715 ("x86, nmi, drivers: Fix nmi splitup build bug")

Arm64 does not support NMI and has no <asm/nmi.h>.

Include <asm/nmi.h> only if CONFIG_HPWDT_NMI_DECODING is defined to
avoid build failure on non-existent header file on Arm64.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220820202821.1263837-2-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: New PCI IDs

New hardware with new PCI ID info.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620878612-24736-2-git-send-email-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Assign boolean values to a bool variable

Fix the following coccicheck warnings:

./drivers/watchdog/hpwdt.c:345:2-12: WARNING: Assignment of
0/1 to bool variable.

./drivers/watchdog/hpwdt.c:126:2-12: WARNING: Assignment of
0/1 to bool variable.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Reviewed-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1611128890-79204-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Reflect changes

Bump driver number to reflect recent changes.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1606097320-56762-3-git-send-email-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Disable NMI in Crash Kernel

NMIs received during the crash path are problematic as hpwdt_pretimeout
handling of the NMI would cause a reentry into kdump.

The situation is complicated in that I/O errors can be signaled as NMI
circumventing hpwdt_pretimeout's attempt to not claim NMI not associated
with either the WDT or the iLO NMI switch. These NMI can additionally
cause a secondary NMI which cause the system to hang.

By disabling pretimeout and hpwdtimeout in crash path we both reduce
the risk of receiving an NMI and simuletaneously leave the WDT running
(if it was already in use) to allow the WDT to break the system out of
hangs by the WDT reset.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1606097320-56762-2-git-send-email-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Reflect changes

Bump driver number to reflect recent changes.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Add module parameter kdumptimeout.

Instead of unconditionally stopping the watchdog timer after receipt of
a pretimeout NMI, reprogram the timeout based upon module parameter
kdumptimeout.

The provides a more flexible override than the depricated allow_kdump.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Have core ping watchdog.

Instead of stopping the hw timer during probe, have the core update
the timer if the timer is already running.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Advertize max_hw_heartbeat_ms

Set max_hw_heartbeat_ms instead of max_timeout so that user client can
set timeout range in excess of what the underlying hardware supports.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Stop hpwdt on unregister.

Have the WD core stop the watchdog on unregister instead of explicitly
calling hpwdt_stop() in hpwdt_exit().

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: drop warning after registering device

The core will print out details now.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: hpwdt: drop warning after calling watchdog_init_timeout

The core will print out details now.

Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Update driver version.

Bump version number to reflect recent minor changes.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Do not claim unsupported hardware

Do not claim when SSID 0x0289 as the watchdog features
are not enabled/validated by the firmware.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog/hpwdt: Exclude via blacklist

Instead of having explicit if statments excluding devices,
use a pci_device_id table of devices to blacklist.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Disable PreTimeout when Timeout is smaller

During module install, disable pretimeout if the requested timeout
value is not greater than the minimal pretimeout value that is
supported by hardware.

This makes the module load handling of pretimeout consistent
with the ioctl handling of pretimeout.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Update version number.

Bump version number to reflect recent bug fixes.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Module paramerter alias.

Add module parameter "timeout" as an alias to "soft_margin."
This aligns hpwdt usage more closely with other WDT while
retaining backwards compatibility.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Display module parameters.

Print module parameters when the driver is loaded.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Claim NMI from iLO

The hwpdt driver is overloaded for handling both the iLO
watchdog and the explicit "Generate NMI to System" virutal
button. Hence NMI handler needs to claim NMI resulting
from the virutal button.

Claim if iLO generated accommodating firmware that might
set wrong bit.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Initialize pretimeout from module parameter.

When the pretimeout is specified as a module parameter, the
value should be reflected in hpwdt_dev.pretimeout. The default
(on) case is correct. But, when disabling pretimeout, the value
should be set to zero in hpwdt_dev.

When compiling w/o CONFIG_HPWDT_NMI_DECODING defined, the pretimeout
module parameter is ignored and the value internally will be 0.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

watchdog: hpwdt: Claim NMIs generated by iLO5

On iLO5 going forward we want to return and not claim the NMI, if
the NMI was NOT gnerated by the iLO as a result of the watchdog
timing out or an explicit generate NMI.

The sense of the test in is inverted and prevents hpwdt_pretimeout
from claiming NMIs when it should.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Fixes: a042229a18ac ("watchdog: hpwdt: Update nmi_panic message.")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Update driver version.

Update driver version number to reflect changes.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Add dynamic debug

Add a few dynamic debug messages to aid in module level debug.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Programable Pretimeout NMI

Make whether or not the hpwdt watchdog delivers a pretimeout NMI
programable by the user.

The underlying iLO hardware is programmable as to whether or not
a pre-timeout NMI is delivered to the system before the iLO resets
the system. However, the iLO does not allow for programming the
length of time that NMI is delivered before the system is reset.

By watchdog API, in hpwdt_set_pretimeout a val == 0 disables the NMI.
When val != 0, hpwdt_set_pretimeout will enable the pretimeout NMI
provided the current timeout is greator than the HW specified
pretimeout length. Otherwise an error is returned.

In set_timeout, if the new timeout is <= an already established pretimeout,
the pretimeout is canceled. This matches the action watchdog_set_timeout
in the watchdog core would do if an hpwdt specific set_timeout
function wasn't specified.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: remove allow_kdump module parameter.

The intent of this parameter is unclear and it sets up a
race between the reset of the system by ASR and crashdump.

The length of time between receipt of the pretimeout NMI
and the ASR reset of the system is fixed by hardware.

Turning the parameter off doesn't necessairly prevent a crash dump.
Also, having the ASR reset occur while the system is crash dumping
doesn't imply that the dump was hung given the short duration
between the NMI and the reset.

This parameter is not a substitute for having a architected watchdog
crashdump hang detection paridigm.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: condition early return of NMI handler on iLO5

Modify prior change to not claim an NMI unless originated
from iLO to apply only to iLO5 and later going forward.
This restores hpwdt traditional behavior of calling panic
if the NMI is NMI_IO_CHECK, NMI_SERR, or NMI_UNKNOWN for
legacy hardware.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Modify to use watchdog core.

Follow Documentation/watchdog/convert_drivers_to_kernel_api.txt to
convert hpwdt from legacy watchdog driver to use the watchdog core.

Removed functions: hpwdt_open, hpwdt_release, hpwdt_write, hpwdt_ioctl
Removed data structures: hpwdt_fops, hpwdt_miscdev, watchdog_device
Modified functions: hpwdt_start, hpwdt_stop, hpwdt_ping, hpwdt_gettimeleft
Added functions: hpwdt_settimeout
Added structures: watchdog_device

Update Kconfig file to show that hpwdt now selects WATCHDOG_CORE.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Update nmi_panic message.

Include the nmistat in the nmi_panic message to give support
an indication why the NMI was called (e.g. a timeout or generate
nmi button.)

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Update Module info and copyright.

Update Copyright and Module description to reflect branding changes.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Remove legacy NMI sourcing.

Gen8 and prior Proliant systems supported the "CRU" interface
to firmware. This interfaces allows linux to "call back" into firmware
to source the cause of an NMI. This feature isn't fully utilized
as the actual source of the NMI isn't printed, the driver only
indicates that the source couldn't be determined when the call
fails.

With the advent of Gen9, iCRU replaces the CRU. The call back
feature is no longer available in firmware. To be compatible and
not attempt to call back into firmware on system not supporting CRU,
the SMBIOS table is consulted to determine if it is safe to
make the call back or not.

This results in about half of the driver code being devoted
to either making CRU calls or determing if it is safe to make
CRU calls. As noted, the driver isn't really using the results of
the CRU calls.

Furthermore, as a consequence of the Spectre security issue, the
BIOS/EFI calls are being wrapped into Spectre-disabling section.
Removing the call back in hpwdt_pretimeout assists in this effort.

As the CRU sourcing of the NMI isn't required for handling the
NMI and there are security concerns with making the call back, remove
the legacy (pre Gen9) NMI sourcing and the DMI code to determine if
the system had the CRU interface.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: fix unused variable warning

The new hpwdt_my_nmi() function is used conditionally, which produces
a harmless warning in some configurations:

drivers/watchdog/hpwdt.c:478:12: error: 'hpwdt_my_nmi' defined but not used [-Werror=unused-function]

This moves it inside of the #ifdef that protects its caller, to silence
the warning.

Fixes: 621174a92851 ("watchdog: hpwdt: Check source of NMI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Check source of NMI

Do not claim the NMI (i.e. return NMI_DONE) if the source of
the NMI isn't the iLO watchdog or debug.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: SMBIOS check

This corrects:
commit cce78da76601 ("watchdog: hpwdt: Add check for UEFI bits")

The test on HPE SMBIOS extension type 219 record "Misc Features"
bits for UEFI support is incorrect. The definition of the Misc Features
bits in the HPE SMBIOS OEM Extensions specification (and related
firmware) was changed to use a different pair of bits to
represent UEFI supported. Howerver, a corresponding change
to Linux was missed.

Current code/platform work because the iCRU test is working.
But purpose of cce78da766 is to ensure correct functionality
on future systems where iCRU isn't supported.

Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

drivers/watchdog/hpwdt.c: use set_memory.h header

set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.

Link: http://lkml.kernel.org/r/1488920133-27229-10-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

watchdog: hpwdt: add support for iLO5

iLO5 will offer the same watchdog timer as previous generations, but the
PCI subsystem vendor ID will be PCI_VENDOR_ID_HP_3PAR (0x1590) instead of
PCI_VENDOR_ID_HP (0x103c). Add 0x1590 to the whitelist and be more
specific when ignoring the 103c,1979 device.

Signed-off-by: Brian Boylston <brian.boylston@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

hpwdt: use nmi_panic() when kernel panics in NMI handler

Commit 1717f2096b54 ("panic, x86: Fix re-entrance problem due to panic
on NMI") introduced nmi_panic() which prevents concurrent and recursive
execution of panic(). It also saves registers for the crash dump on x86
by later commit 58c5661f2144 ("panic, x86: Allow CPUs to save registers
even if looping in NMI context").

hpwdt driver can call panic() from NMI handler, so replace it with
nmi_panic(). Also, do some cleanups.

Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Thomas Mingarelli <thomas.mingarelli@hpe.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

watchdog/hpwdt: Fix build on certain configs

Fix the following build failure:

drivers/watchdog/hpwdt.c:359:5: error: expected ‘)’ before ‘FRAME_BEGIN’

which occurs because hpwdt.c relied on indirect inclusion to get asm/frame.h
definitions - but some (mostly randconfig) configs did not provide that.

Include <asm/frame.h> explicitly.

Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: live-patching@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

watchdog/hpwdt: Create stack frame in asminline_call()

asminline_call() is a callable non-leaf function which doesn't honor
CONFIG_FRAME_POINTER, which can result in bad stack traces.

Create a stack frame when CONFIG_FRAME_POINTER is enabled.

Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/60de3cfb6f16d413bfb923036cc87fec132df735.1453405861.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

watchdog: hpwdt: HP rebranding

This patch is for the rebranding changes for the corporate split at HP.
There are no functional changes with this patch.

Signed-off-by: Tom Mingarelli <thomas.mingarelli@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Add support for WDIOC_SETOPTIONS

WDIOC_SETOPTIONS makes it possible to disable and re-enable the
watchdog timer while the hpwdt driver is loaded.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: Fix initialization message in hpwdt.c

allow_kdump was enabled as default since following commit.

commit a089361cf5f1d6a5295aa5385238bd044998e1e9,
watchdog: hpwdt: Unregister NMI events on exit.

But the initialization message was not modified.
So it still shows

HP Watchdog Timer Driver: NMI decoding initialized,
allow kernel dump: ON (default = 0/OFF) <=

This "default = 0/OFF" message may confuse users.
Fix it as "default = 1/ON".

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: delete non-required instances of include <linux/init.h>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org

watchdog: hpwdt patch to display informative string

This patch is being submitted to output a general string when the panic comes
in that informs the user of the possible places to look for the source of the
NMI. Because various systems log the message in different places this would
give a single display of where to go look instead of code that acts on all
these different server names or IDs.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: remove DEFINE_PCI_DEVICE_TABLE macro

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: Get rid of MODULE_ALIAS_MISCDEV statements

I just can't find any value in MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR)
and MODULE_ALIAS_MISCDEV(TEMP_MINOR) statements.

Either the device is enumerated and the driver already has a module
alias (e.g. PCI, USB etc.) that will get the right driver loaded
automatically.

Or the device is not enumerated and loading its driver will lead to
more or less intrusive hardware poking. Such hardware poking should be
limited to a bare minimum, so the user should really decide which
drivers should be tried and in what order. Trying them all in
arbitrary order can't do any good.

On top of that, loading that many drivers at once bloats the kernel
log. Also many drivers will stay loaded afterward, bloating the output
of "lsmod" and wasting memory. Some modules (cs5535_mfgpt which gets
loaded as a dependency) can't even be unloaded!

If defining char-major-10-130 is needed then it should happen in
user-space.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Jim Cromie <jim.cromie@gmail.com>

watchdog: hpwdt: Patch to ignore auxilary iLO devices

This patch is to prevent hpwdt from loading on any auxilary iLO devices defined
after the initial (or main) iLO device. All auxilary iLO devices will have a
subsystem device ID set to 0x1979 in order for hpwdt to differentiate between
the two types.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

lto, watchdog/hpwdt.c: make assembler label global

We cannot assume that the inline assembler code always ends up in the same
file as the original C file. So make any assembler labels that are called
with "extern" by C global

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

watchdog: hpwdt: Add check for UEFI bits

This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
----
drivers/watchdog/hpwdt.c | 9 ++++++---
1 files changed, 6 insertions(+), 3 deletions(-)

watchdog: hpwdt.c: Increase version string

Changing the version of the driver for all the latest patches being applied
for kdump fixes.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: remove use of __devexit

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: remove use of __devinit

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: remove use of __devexit_p

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hpwdt: Fix kdump issue in hpwdt

kdump can be interrupted by watchdog timer when the timer is left
activated on the crash kernel. Changed the hpwdt driver to disable
watchdog timer at boot-time. This assures that watchdog timer is
disabled until /dev/watchdog is opened, and prevents watchdog timer
to be left running on the crash kernel.

Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>

watchdog: hpwdt: Unregister NMI events on exit.

This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: Use module_pci_driver

This patch converts the PCI watchdog drivers so that they use the
module_pci_driver() macro. This makes the code smaller and simpler.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Marc Vertes <marc.vertes@sigfox.com>

hpwdt: Only BYTE reads/writes to WD Timer port 0x72

This patch is to correct the use of the iLO port 0x72 usage.
The port 0x72 is a byte size write/read and hpwdt is currently
writing a WORD.

Signed-off by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

x86/nmi: Add new NMI queues to deal with IO_CHK and SERR

In discussions with Thomas Mingarelli about hpwdt, he explained
to me some issues they were some when using their virtual NMI
button to test the hpwdt driver.

It turns out the virtual NMI button used on HP's machines do no
send unknown NMIs but instead send IO_CHK NMIs. The way the
kernel code is written, the hpwdt driver can not register itself
against that type of NMI and therefore can not successfully
capture system information before panic'ing.

To solve this I created two new NMI queues to allow driver to
register against the IO_CHK and SERR NMIs. Or in the hpwdt all
three (if you include unknown NMIs too).

The change is straightforward and just mimics what the unknown
NMI does.

Reported-and-tested-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1333051877-15755-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

watchdog, hpwdt: Remove priority option for NMI callback

The NMI_UNKNOWN bucket only allows for one function to register
to it. The reason for that is because only functions which can
not determine if the NMI belongs to them or not should register
and would like to assume/swallow any NMI they see.

As a result it doesn't make sense to let more than one function
like this register. In fact, letting a second function fail
allows us to know that more than one function is going to
swallow NMIs on the current system. This is better than silently
being ignored.

Therefore hpwdt's priority mechanism doesn't make sense any
more. They will be always first on the NMI_UNKNOWN queue, if
they register.

Removing this parameter cleans up the code and simplifies things
for the next patch which changes how nmis are registered.

Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1333051877-15755-2-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

watchdog: nowayout is bool

nowayout is actually a boolean value.
So make it bool for all watchdog device drivers.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: Use pr_<fmt> and pr_<level>

Use the current logging styles.

Make sure all output has a prefix.
Add missing newlines.
Remove now unnecessary PFX, NAME, and miscellaneous other #defines.
Coalesce formats.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: clean up set_memory_x call for 32 bit

1. address has to be page aligned.
2. set_memory_x uses page size argument, not size.
Bug causes with following commit:
commit da28179b4e90dda56912ee825c7eaa62fc103797
Author: Mingarelli, Thomas <Thomas.Mingarelli@hp.com>
Date: Mon Nov 7 10:59:00 2011 +0100

watchdog: hpwdt: Changes to handle NX secure bit in 32bit path

commit e67d668e147c3b4fec638c9e0ace04319f5ceccd upstream.

This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.

Signed-off-by: Maxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>

watchdog: hpwdt: Changes to handle NX secure bit in 32bit path

This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.

This is needed for SLES11 SP2 and the latest upstream kernel as it appears
the NX Execute Disable has grown in its control.

Signed-off by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@kernel.org

x86, nmi, drivers: Fix nmi splitup build bug

nmi.c needs an #include <linux/mca.h>:

arch/x86/kernel/nmi.c: In function ‘unknown_nmi_error’:
arch/x86/kernel/nmi.c:286:6: error: ‘MCA_bus’ undeclared (first use in this function)
arch/x86/kernel/nmi.c:286:6: note: each undeclared identifier is reported only once for each function it appears in

Another one is the hpwdt driver:

drivers/watchdog/hpwdt.c:507:9: error: ‘NMI_DONE’ undeclared (first use in this function)

Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, nmi: Wire up NMI handlers to new routines

Just convert all the files that have an nmi handler to the new routines.
Most of it is straight forward conversion. A couple of places needed some
tweaking like kgdb which separates the debug notifier from the nmi handler
and mce removes a call to notify_die.

[Thanks to Ying for finding out the history behind that mce call

https://lkml.org/lkml/2010/5/27/114

And Boris responding that he would like to remove that call because of it

https://lkml.org/lkml/2011/9/21/163]

The things that get converted are the registeration/unregistration routines
and the nmi handler itself has its args changed along with code removal
to check which list it is on (most are on one NMI list except for kgdb
which has both an NMI routine and an NMI Unknown routine).

Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1317409584-23662-4-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

watchdog: hpwdt: prevent multiple "NMI occurred" messages

On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.

Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.

Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: add next gen HP servers

This patch is required to enable hpwdt to work on next generation HP servers
with iLO.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: convert to DEFINE_PCI_DEVICE_TABLE

Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE tables.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: eliminate section mismatch warning

hpwdt_init_nmi_decoding() is called in hpwdt_init_one error handling,
thus remove the __devexit annotation of hpwdt_exit_nmi_decoding().

This patch fixes below warning:

WARNING: drivers/watchdog/hpwdt.o(.devinit.text+0x36f): Section mismatch in reference from the function hpwdt_init_one() to the function .devexit.text:hpwdt_exit_nmi_decoding()
The function __devinit hpwdt_init_one() references
a function __devexit hpwdt_exit_nmi_decoding().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
hpwdt_exit_nmi_decoding() so it may be used outside an exit section.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

x86: Convert some devices to use DIE_NMIUNKNOWN

They are a handful of places in the code that register a die_notifier
as a catch all in case no claims the NMI. Unfortunately, they trigger
on events like DIE_NMI and DIE_NMI_IPI, which depending on when they
registered may collide with other handlers that have the ability to
determine if the NMI is theirs or not.

The function unknown_nmi_error() makes one last effort to walk the
die_chain when no one else has claimed the NMI before spitting out
messages that the NMI is unknown.

This is a better spot for these devices to execute any code without
colliding with the other handlers.

The two drivers modified are only compiled on x86 arches I believe, so
they shouldn't be affected by other arches that may not have
DIE_NMIUNKNOWN defined.

Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Cc: dann frazier <dannf@hp.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, nmi_watchdog: Remove ARCH_HAS_NMI_WATCHDOG and rely on CONFIG_HARDLOCKUP_DETECTOR

The x86 arch has shifted its use of the nmi_watchdog from a
local implementation to the global one provide by
kernel/watchdog.c. This shift has caused a whole bunch of
compile problems under different config options. I attempt to
simplify things with the patch below.

In order to simplify things, I had to come to terms with the
meaning of two terms ARCH_HAS_NMI_WATCHDOG and
CONFIG_HARDLOCKUP_DETECTOR. Basically they mean the same thing,
the former on a local level and the latter on a global level.

With the old x86 nmi watchdog gone, there is no need to rely on
defining the ARCH_HAS_NMI_WATCHDOG variable because it doesn't
make sense any more. x86 will now use the global
implementation.

The changes below do a few things. First it changes the few
places that relied on ARCH_HAS_NMI_WATCHDOG to use
CONFIG_X86_LOCAL_APIC (the former was an alias for the latter
anyway, so nothing unusual here). Those pieces of code were
relying more on local apic functionality the nmi watchdog
functionality, so the change should make sense.

Second, I removed the x86 implementation of
touch_nmi_watchdog(). It isn't need now, instead x86 will rely
on kernel/watchdog.c's implementation.

Third, I removed the #define ARCH_HAS_NMI_WATCHDOG itself from
x86. And tweaked the include/linux/nmi.h file to tell users to
look for an externally defined touch_nmi_watchdog in the case of
ARCH_HAS_NMI_WATCHDOG _or_ CONFIG_HARDLOCKUP_DETECTOR. This
changes removes some of the ugliness in that file.

Finally, I added a Kconfig dependency for
CONFIG_HARDLOCKUP_DETECTOR that said you can't have
ARCH_HAS_NMI_WATCHDOG _and_ CONFIG_HARDLOCKUP_DETECTOR. You can
only have one nmi_watchdog.

Tested with
ARCH=i386: allnoconfig, defconfig, allyesconfig, (various broken
configs) ARCH=x86_64: allnoconfig, defconfig, allyesconfig,
(various broken configs)

Hopefully, after this patch I won't get any more compile broken
emails. :-)

v3:
changed a couple of 'linux/nmi.h' -> 'asm/nmi.h' to pick-up correct function
prototypes when CONFIG_HARDLOCKUP_DETECTOR is not set.

Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1293044403-14117-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, nmi_watchdog: Remove all stub function calls from old nmi_watchdog

Now that the bulk of the old nmi_watchdog is gone, remove all
the stub variables and hooks associated with it.

This touches lots of files mainly because of how the io_apic
nmi_watchdog was implemented. Now that the io_apic nmi_watchdog
is forever gone, remove all its fingers.

Most of this code was not being exercised by virtue of
nmi_watchdog != NMI_IO_APIC, so there shouldn't be anything to
risky here.

Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: fweisbec@gmail.com
Cc: gorcunov@openvz.org
LKML-Reference: <1289578944-28564-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

watchdog: hpwdt (12/12): Make NMI decoding a compile-time option

hpwdt is quite functional without the NMI decoding feature.
This change lets users disable the NMI portion at compile-time
via the new HPWDT_NMI_DECODING config option.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (11/12): move NMI-decoding init and exit to seperate functions

Move NMI-decoding initialisation and exit code to seperate functions so that
we can ifdef-out parts of it in the future.

Also, this is for a device, so let's use dev_info instead of printk.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (10/12): Use "decoding" instead of "sourcing"

The term "decoding" more clearly explains what hpwdt is doing. It isn't
just finding the source of the interrupt, but rather aids in decoding what
the interrupt means.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (9/12): hpwdt_pretimeout reorganization

Reorganize this function to remove excess indentation and highlight
the single return code. (No functional change).

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (8/12): implement WDIOC_GETTIMELEFT

Let applications check the amount of time left before the watchdog will fire.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (7/12): allow full range of timer values supported by hardware

The hpwdt timer is a 16 bit value with 128ms resolution.
Let applications use this entire range.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (6/12): Introduce SECS_TO_TICKS() macro

Define a macro to convert from seconds to timer ticks.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (5/12): Make x86 assembly ifdef guard more strict

The 32-bit assembly is guarded by an #ifndef CONFIG_X86_64. Kconfig prevents
us from building this driver on !X86, so that happens to suffice - but we
should really lock it down to #ifdef CONFIG_X86_32.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (4/12): Despecificate driver from iLO2

This driver supports both iLO2 and iLO3, but our user-visible strings
currently only reference iLO2. Let's just call it "iLO2+" to avoid having
to update strings for each iLO generation. This driver doesn't support
iLO ASICs prior to iLO2, but that is sufficiently explained in Kconfig.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (3/12): Group NMI sourcing specific items together

* Group together includes specific to NMI sourcing
* Group defines only used by NMI sourcing together
* Group declarations specific to NMI sourcing together

This gives a clean seperation of watchdog specific items and
NMI sourcing specific items (which is needed for making it
possible to build hpwdt without the NMI functionality).

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (2/12): Group options that affect watchdog behavior together

Reorganization only.

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt (1/12): clean-up include-files.

* remove unnecessary includes
* We use a spinlock, but lacked the include
* We need bitops.h for test_and_set_bit/clear_bit

Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

watchdog: hpwdt: formatting of pointers in printk()

Use %p instead of %08x in printk().

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt - fix lower timeout limit

[Novell Bug 581103] HP Watchdog driver has arbitrary (wrong) timeout limits.
Fix the lower timeout limit to a more appropriate value.

Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.

2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).

* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

[WATCHDOG] watchdog_info constify

make the watchdog_info struct const where possible.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt: Add NMI priority option

Add a priority option so that the user can choose if we do the NMI
first or last.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt: Add NMI sourcing

Add NMI sourcing functionality (Can only be active if nmi_watchdog is
inactive).

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

dmi: Let dmi_walk() users pass private data

At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>

[WATCHDOG] More coding-style and trivial clean-up

Some more cleaning-up of the watchdog drivers.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] struct file_operations should be const

Fix following warnings:
WARNING: struct file_operations should normally be const

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt.c: Add new HP BMC controller.

Add the PCI-ID for the upcoming new BMC controller for HP hardware.

Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt: Fix kdump when using hpwdt

When the "hpwdt" module is loaded (even if the /dev/watchdog device is not
opened), then kdump does not work. The panic kernel either does not start at
all or crash in various places.

The problem is that hpwdt_pretimeout is registered with register_die_notifier()
with the highest possible priority. Because it returns NOTIFY_STOP, the
crash_nmi_callback which is also registered with register_die_notifier()
is never executed. This causes the shutdown of other CPUs to fail.

Reverting the order is no option: The crash_nmi_callback executes HLT
and so never returns normally. Because of that, it must be executed as
last notifier, which currently is done.

So, that patch returns NOTIFY_OK to keep the crash_nmi_callback executed.

Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Vivek Goyal <vgoyal@redhat.com>

[WATCHDOG] hpwdt: set the mapped BIOS address space as executable

The address provided by the SMBIOS/DMI CRU information is mapped via
ioremap() in the virtual address space. However, since the address is
executed (i.e. call'd), we need to set that pages as executable.

Without that, I get following oops on a HP ProLiant DL385 G2
machine with BIOS from 05/29/2008 when I trigger crashdump:

BUG: unable to handle kernel paging request at ffffc20011090c00
IP: [<ffffc20011090c00>] 0xffffc20011090c00
PGD 12f813067 PUD 7fe6a067 PMD 7effe067 PTE 80000000fffd3173
Oops: 0011 [1] SMP
last sysfs file: /sys/devices/system/cpu/cpu3/cache/index2/shared_cpu_map
CPU 1
Modules linked in: autofs4 ipv6 af_packet cpufreq_conservative cpufreq_userspace
cpufreq_powersave powernow_k8 fuse loop dm_mod rtc_cmos ipmi_si sg rtc_core i2c
_piix4 ipmi_msghandler bnx2 sr_mod container button i2c_core hpilo joydev pcspkr
rtc_lib shpchp hpwdt cdrom pci_hotplug usbhid hid ff_memless ohci_hcd ehci_hcd
uhci_hcd usbcore edd ext3 mbcache jbd fan ide_pci_generic serverworks ide_core p
ata_serverworks pata_acpi cciss ata_generic libata scsi_mod dock thermal process
or thermal_sys hwmon
Supported: Yes
Pid: 0, comm: swapper Not tainted 2.6.27.5-HEAD_20081111100657-default #1
RIP: 0010:[<ffffc20011090c00>] [<ffffc20011090c00>] 0xffffc20011090c00
RSP: 0018:ffff88012f6f9e68 EFLAGS: 00010046
RAX: 0000000000000d02 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88012f6f9e98 R08: 666666666666660a R09: ffffffffa1006fc0
R10: 0000000000000000 R11: ffff88012f6f3ea8 R12: ffffc20011090c00
R13: ffff88012f6f9ee8 R14: 000000000000000e R15: 0000000000000000
FS: 00007ff70b29a6f0(0000) GS:ffff88012f6512c0(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffffc20011090c00 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff88012f6f2000, task ffff88007fa8a1c0)
Stack: ffffffffa0f8502b 0000000000000002 ffffffff80738d50 0000000000000000
0000000000000046 0000000000000046 00000000fffffffe ffffffffa0f852ec
0000000000000000 ffffffff804ad9a6 0000000000000000 0000000000000000
Call Trace:
Inexact backtrace:

<NMI> [<ffffffffa0f8502b>] ? asminline_call+0x2b/0x55 [hpwdt]
[<ffffffffa0f852ec>] hpwdt_pretimeout+0x3c/0xa0 [hpwdt]
[<ffffffff804ad9a6>] ? notifier_call_chain+0x29/0x4c
[<ffffffff802587e4>] ? notify_die+0x2d/0x32
[<ffffffff804abbdc>] ? default_do_nmi+0x53/0x1d9
[<ffffffff804abd90>] ? do_nmi+0x2e/0x43
[<ffffffff804ab552>] ? nmi+0xa2/0xd0
[<ffffffff80221ef9>] ? native_safe_halt+0x2/0x3
<<EOE>> [<ffffffff8021345d>] ? default_idle+0x38/0x54
[<ffffffff8021359a>] ? c1e_idle+0x118/0x11c
[<ffffffff8020b3b5>] ? cpu_idle+0xa9/0xf1

Code: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff <55> 50 e8 00 00 00 00 58 48 2d 07 10 40 00 48 8b e8 58 e9 68 02
RIP [<ffffc20011090c00>] 0xffffc20011090c00
RSP <ffff88012f6f9e68>
CR2: ffffc20011090c00
Kernel panic - not syncing: Fatal exception

Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

[WATCHDOG] hpwdt.c kdebug support

add kdebug support for the hpwdt.c driver.

Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] more coding style clean-up's

More coding style clean-up's.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt.c - fix double includes

The last clean-up created 2 times the same include. delete the doubles.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

hpwdt: don't use static flags

Static (read: global) is potential problem. Two threads can corrupt each
other's interrupt status, better avoid this.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[watchdog] hpwdt: fix use of inline assembly

The inline assembly in drivers/watchdog/hpwdt.c was incredibly broken,
and included all the function prologue and epilogue stuff, even though
it was itself then inside a C function where the compiler would add its
own prologue and epilogue on top of it all.

This then just _happened_ to work if you had exactly the right compiler
version and exactly the right compiler flags, so that gcc just happened
to not create any prologue at all (the gcc-generated epilogue wouldn't
matter, since it would never be reached).

But the more proper way to fix it is to simply not do this. Move the
inline asm to the top level, with no surrounding function at all (the
better alternative would be to remove the prologue and make it actually
use proper description of the arguments to the inline asm, but that's a
bigger change than the one I'm willing to make right now).

Tested-by: S.Çağlar Onur <caglar@pardus.org.tr>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Revert "[WATCHDOG] hpwdt: Fix NMI handling."

The old setup works better.

Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Revert "[WATCHDOG] make watchdog/hpwdt.c:asminline_call() static"

The driver needs the asmlinkage tag and the CFLAGS line in the Makefile.
Without it the driver doesn't work.

Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 11/57] hpwdt: couple of include cleanups

clean-up includes

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] hpwdt: Fix NMI handling.

I need to just return in case it's not my NMI so someone else can take a look
at it (and reset die_nmi_called to 0 in case I actually do get one that's mine
to handle).

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG] make watchdog/hpwdt.c:asminline_call() static

This patch makes the needlessly global asminline_call() static and
removes the not required "asmlinkage".

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Andrew Morton <akpm@linux-foundation.org>

[WATCHDOG] hpwdt: Use dmi_walk() instead of own copy

We can simplify the code by deleting all of the duplicated DMI table
walking code and using the kernel's existing dmi_walk() interface to
find the DMI entry the driver is looking for.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

[WATCHDOG] Fix return value warning in hpwdt

The return value of smbios_scan_machine() is never used, and when it
succeeds it doesn't return anything, so just make it void. This fixes:

drivers/watchdog/hpwdt.c: In function 'smbios_scan_machine':
drivers/watchdog/hpwdt.c:562: warning: control reaches end of non-void function

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

[WATCHDOG] Fix declaration of struct smbios_entry_point in hpwdt

On my HP DL380 G5 system running a 64-bit kernel, loading the hpwdt
driver causes a crash because the driver attempts to ioremap an
invalid physical address. This is because the driver has an incorrect
definition of the SMBIOS table entry point structure: the table
address is only a 32-bit quantity, and making it a u64 means that the
high-order 32 bits end up containing garbage.

Correcting the structure definition fixes the driver so that it loads
without any problems on my system.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

[WATCHDOG] HP ProLiant WatchDog driver

Hp is providing a Hardware WatchDog Timer driver that will only work with the
specific HW Timer located in the HP ProLiant iLO 2 ASIC. The iLO 2 HW Timer
will generate a Non-maskable Interrupt (NMI) 9 seconds before physically
resetting the server, by removing power, so that the event can be logged to
the HP Integrated Management Log (IML), a Non-Volatile Random Access Memory
(NVRAM). The logging of the event is performed using the HP ProLiant ROM via
an Industry Standard access known as a BIOS Service Directory Entry.

Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>