backlight: Add Kinetic KTD2801 Backlight support

KTD2801 is a LED backlight driver IC found in samsung,coreprimevelte.
The brightness can be set using PWM or the ExpressWire protocol. Add
support for the KTD2801.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-4-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>

backlight: mp3309c: Add support for MPS MP3309C

The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
programmable switching frequency to optimize efficiency.
The brightness can be controlled either by I2C commands (called "analog"
mode) or by a PWM input signal (PWM mode).
This driver supports both modes.

For DT configuration details, please refer to:
- Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml

The datasheet is available at:
- https://www.monolithicpower.com/en/mp3309c.html

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20231116105319.957600-3-f.suligoi@asem.it
Signed-off-by: Lee Jones <lee@kernel.org>

fbdev: Remove support for Carillo Ranch driver

As far as anybody can tell, this product never shipped. If it did,
it shipped in 2007 and nobody has access to one any more. Remove the
fbdev driver and the backlight driver.

Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Helge Deller <deller@gmx.de>

backlight: apple_bl: Use acpi_video_get_backlight_type()

On some MacBooks both the apple_bl and the apple-gmux backlight drivers
may be able to export a /sys/class/backlight device.

To avoid having 2 backlight devices for one LCD panel until now
the apple-gmux driver has been calling apple_bl_unregister() to move
the apple_bl backlight device out of the way when it loads.

Similar problems exist on other x86 laptops and all backlight drivers
which may be used on x86 laptops have moved to using
acpi_video_get_backlight_type() to determine whether they should load
or not.

Switch apple_bl to this model too, so that it is consistent with all
the other x86 backlight drivers.

Besides code-simplification and consistency this has 2 other benefits:

1) It removes a race during boot where userspace will briefly see
an apple_bl backlight and then have it disappear again, leading to e.g.:
https://bbs.archlinux.org/viewtopic.php?id=269920

2) This allows user to switch between the drivers by passing
acpi_backlight=apple_gmux or acpi_backlight=vendor on the kernel
commandline.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230307120540.389920-1-hdegoede@redhat.com

backlight: ktz8866: Add support for Kinetic KTZ8866 backlight

Add support for Kinetic KTZ8866 backlight, which is used in
Xiaomi tablet, Mi Pad 5 series. This driver lightly based on
downstream implementation [1].
[1] https://github.com/MiCode/Xiaomi_Kernel_OpenSource/blob/elish-r-oss/drivers/video/backlight/ktz8866.c

Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120155018.15376-2-lujianhua000@gmail.com

backlight: Remove pxa tosa support

The PXA tosa machine was removed, so this backlight driver is no
longer needed.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230105134622.254560-10-arnd@kernel.org

video: backlight: mt6370: Add MediaTek MT6370 support

MediaTek MT6370 is a SubPMIC consisting of a single cell battery charger
with ADC monitoring, RGB LEDs, dual channel flashlight, WLED backlight
driver, display bias voltage supply, one general purpose LDO, and the
USB Type-C & PD controller complies with the latest USB Type-C and PD
standards.

Add support for the MediaTek MT6370 backlight driver.
It controls 4 channels of 8 series WLEDs in
2048 (only for MT6370/MT6371) / 16384 (only for MT6372)
current steps (30 mA) in exponential or linear mapping curves.

Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220830034042.9354-11-peterwu.pub@gmail.com

fbdev: omap: avoid using mach/*.h files

All the headers we actually need are now in include/linux/soc,
so use those versions instead and allow compile-testing on
other architectures.

Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

backlight: Kconfig whitespace and indentation cleanups

Remove leading whitespaces, replace multi spaces with tabs, and fix help
text indentation.

Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: rt4831: Adds support for Richtek RT4831 backlight

Adds support for Richtek RT4831 backlight.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Add Kinetic KTD253 backlight driver

The Kinetic KTD253 backlight driver is controlled with a
single GPIO line, but still supports a range of brightness
settings by sending fast pulses on the line.

This is based off the source code release for the Samsung
GT-S7710 mobile phone.

Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: generic_bl: Remove this driver as it is unused

The backlight_bl driver required initialization using
struct generic_bl_info. As there are no more references
to this struct there is no users left.
So it is safe to delete the driver.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Delete the OT200 backlight driver

This driver has no in-kernel users. The device can only be populated
by board files since it does not support device tree nor ACPI,
and nothing in the kernel creates a device named "ot200-backlight".

This driver has been in the kernel since 2012. If it is used by
out-of-tree code that code should have been upstreamed by now,
it's been 8 years.

It uses the idiomatic forked GPIO of the CS5535 which combines
pin control and GPIO into its private custom interface, which
causes me a headache because that is not how we do things these
days: we creates separate pin control and GPIO drivers.

Delete this unused driver.

Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: add led-backlight driver

This patch adds a led-backlight driver (led_bl), which is similar to
pwm_bl except the driver uses a LED class driver to adjust the
brightness in the HW. Multiple LEDs can be used for a single backlight.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

video: Fix Kconfig indentation

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191120133838.13132-1-krzk@kernel.org

backlight: qcom-wled: Rename pm8941-wled.c to qcom-wled.c

pm8941-wled.c driver is supporting the WLED peripheral
on pm8941. Rename it to qcom-wled.c so that it can support
WLED on multiple PMICs.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Kconfig: jornada720: Use CONFIG_PREEMPTION

CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.

Switch the Kconfig dependency to CONFIG_PREEMPTION.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[Sebastian: +LCD_HP700]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

video: backlight: Drop default m for {LCD,BACKLIGHT_CLASS_DEVICE}

When running "make oldconfig" on a .config where
CONFIG_BACKLIGHT_LCD_SUPPORT is not set, two new config options
("Lowlevel LCD controls" and "Lowlevel Backlight controls") appear, both
defaulting to "m".

Drop the "default m", as options should default to disabled, and because
several driver config options already select LCD_CLASS_DEVICE or
BACKLIGHT_CLASS_DEVICE when needed.

Fixes: 8c5dc8d9f19c7992 ("video: backlight: Remove useless BACKLIGHT_LCD_SUPPORT kernel symbol")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: lcd: Remove useless BACKLIGHT_CLASS_DEVICE dependencies

This patch removes dependencies on BACKLIGHT_CLASS_DEVICE for items
that are already placed under 'if BACKLIGHT_CLASS_DEVICE'.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

video: backlight: Remove useless BACKLIGHT_LCD_SUPPORT kernel symbol

We have two *_CLASS_DEVICE kernel config options (LCD_CLASS_DEVICE
and BACKLIGHT_LCD_DEVICE) that do the same job.
The patch removes useless BACKLIGHT_LCD_SUPPORT option
and converts LCD_CLASS_DEVICE into a menu.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Remove ld9040 driver

The driver for LD9040 AMOLED LCD panel was superseded with DRM driver
panel-samsung-ld9040.c. It does not support DeviceTree and respective
possible user (Exynos4210 Universal C210) is DeviceTree-only and uses
DRM version of driver.

Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Remove s6e63m0 driver

The driver for S6E63M0 AMOLED LCD panel is not used. It does not
support DeviceTree and respective possible users (S5Pv210 Aquila and
Goni boards) are DeviceTree-only.

Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: otm3225a: Add support for ORISE OTM3225A LCD SoC

This patch adds a LCD driver supporting the OTM3225A LCD SoC
from ORISE Technology. This device can drive TFT LC panels having a
resolution of 240x320 pixels. After initializing the OTM3225A using
it's SPI interface it switches to use 16-bib RGB as external
display interface.

Signed-off-by: Felix Brack <fb@ltec.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Add RAVE SP backlight driver

This driver provides access to RAVE SP backlight control
functionality.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Add support for Arctic Sand LED backlight driver chips

This driver provides support for the Arctic Sand arc2c0608 chip,
and provides a framework to support future devices.

Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: pm8941-wled: Move PM8941 WLED driver to backlight

The Qualcomm PM8941 WLED block is used for backlight and should therefor
be in the backlight framework and not in the LED framework. This moves
the driver and adapts to the backlight api instead.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Allow compile test of GPIO consumers if !GPIOLIB

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.

Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: Add support Skyworks SKY81452 backlight driver

Signed-off-by: Gyungoh Yoo <jack.yoo@skyworksinc.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

ARM: at91/Kconfig: remove unused config options

When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

backlight: Add driver for iPAQ micro backlight

This adds a driver for the backlight controlled by the microcontroller
on the Compaq iPAQ series of handheld computers: h3100, h3600
and h3700.

Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: atmel-pwm-bl: remove obsolete driver

The atmel-pwm-bl driver is now obsolete. It is not used by any mainlined boards
and is replaced by the generic pwm_bl with the pawm-atmel driver using the
generic PWM framework.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

video/backlight: LP8788 needs PWM

The LP8788 driver cannot be successfully built if we don't
enable the PWM subsystem. This patch makes that dependency
explicit in Kconfig and prevents broken randconfig builds.

Based on Arnd Bergmann patch but split out into seperate
commits per driver based on feedback.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

video/backlight: LP855X needs PWM

The LP855X driver cannot be successfully built if we don't
enable the PWM subsystem. This patch makes that dependency
explicit in Kconfig and prevents broken randconfig builds.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

video/pxa: LCD_CORGI needs BACKLIGHT_CLASS_DEVICE

This fixes a randconfig build error when BACKLIGHT_CLASS_DEVICE
is disabled, by describing the dependency in Kconfig,
as we do for the other drivers in this directory.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

video/backlight: LM3630A needs PWM

The LM3630A driver cannot be successfully built if we don't
enable the PWM subsystem. This patch makes that dependency
explicit in Kconfig and prevents broken randconfig builds.

Based on Arnd Bergmann patch but split out into seperate
commits per driver based on feedback.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

backlight: lm3630: apply chip revision

The LM3630 chip was revised by TI and chip name was also changed to
LM3630A. And register map, default values and initial sequences are
changed. The files, lm3630_bl.{c,h} are replaced by lm3630a_bl.{c,h} You
can find more information about LM3630A(datasheet, evm etc) at
http://www.ti.com/product/lm3630a

Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lp855x_bl: support new LP8555 device

LP8555 is one of the LP855x family devices.

This device needs pre_init_device() and post_init_device() driver
structure. It's same as LP8557, so the device configuration code is
shared with LP8557. Backlight outputs are generated from dual DC-DC boost
converters. It's configurable EPROM settings which are defined in the
platform data.

Driver documentation and device tree bindings are updated.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Add ROHM BD6107 backlight driver

The BD6107 is a multi-purpose 10 channels LED driver for the mobile
market. Only the main channel is supported by this driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

backlight: Add Sanyo LV5207LP backlight driver

The LV5207LP is a multi-purpose 7 LEDs driver for the mobile market.
Only the main LED is supported by this driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

backlight: Add GPIO-based backlight driver

The GPIO backlight driver controls the backlight in on/off mode through
a single GPIO.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

video: backlight: add ili922x lcd driver

Add LCD driver for Ilitek ILI9221/ILI9222 controller. The driver uses
SPI interface for controller access and configuration and RGB interface
for graphics data transfer.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/Kconfig: fix typo "MACH_SAM9...EK" three times

Fix three typos (originally) introduced by commit a9a84c37d1ee
("atmel_lcdfb: backlight control").

Two of these typos were introduced in v2.6.25. (The third was
introduced in 915190f7d4f0 ("[ARM] 5614/1: at91: atmel_lcdfb: add
at91sam9g10 support to atmel LCD driver")). Checking these commits
reveals that the default value of 'y' has never been set automatically
in all releases since v2.6.25! Perhaps this line might as well be
dropped.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Convert selectors of GENERIC_GPIO to GPIOLIB

GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

backlight: add new lp8788 backlight driver

TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
dri= ver and current sinks. This patch enables LP8788 backlight module.

(Brightness mode)
The brightness is controlled by PWM input or I2C register.
All modes are supported in the driver.

(Platform data)
Configurable data can be defined in the platform side.
name : backlight driver name. (default: "lcd-backlight")
initial_brightness : initial value of backlight brightness
bl_mode : brightness control by PWM or lp8788 register
dim_mode : dimming mode selection
full_scale : full scale current setting
rise_time : brightness ramp up step time
fall_time : brightness ramp down step time
pwm_pol : PWM polarity setting when bl_mode is PWM based
period_ns : platform specific PWM period value. unit is nano.

The default values are set in case no platform data is defined.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lp855x_bl: support new LP8557 device

LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.

Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END

And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add an AS3711 PMIC backlight driver

This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC. Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage. Anyone wishing to use any of those modes
will have to modify the driver.

Tested on sh73a0-based kzm9g board. Only one mode has been tested and
is enabled. That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: backlight: add the Himax HX-8357B LCD controller

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add lms501kf03 LCD driver

Add the lms501kf03 LCD panel driver. The lms501kf03 LCD panel (800 x 480)
driver uses 3-wired SPI inteface.

[akpm@linux-foundation.org: remove unused variable `before_power']
[akpm@linux-foundation.org: make lms501kf03_shutdown() static, per Fengguang]
Signed-off-by: Ilho Lee <Ilho215.lee@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: ili9320: add missing SPI dependency

Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.

drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'

Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: remove ProGear driver

This driver was for the ProGear webpad device which was produced in
2000/2001 and is not available on a market. I no longer have this
hardware so can not even check how Linux works on it.

Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add new lm3639 backlight driver

This driver is a general version for LM3639 backlgiht + flash driver chip
of TI.

LM3639:
The LM3639 is a single chip LCD Display Backlight driver + white LED
Camera driver. Programming is done over an I2C compatible interface.
www.ti.com

[akpm@linux-foundation.org: code layout tweaks]
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add Backlight driver for lm3630 chip

This driver is a general version for LM3630 backlgiht driver chip of TI.

LM3630 :
The LM3630 is a current mode boost converter which supplies the power
and controls the current in two strings of up to 10 LEDs per string.
Programming is done over an I2C compatible interface.
www.ti.com

[akpm@linux-foundation.org: make bled_name[] static, a few coding style tuneups, create new set_intensity(), partly to avoid awkward layout gymnastics]
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Add TPS65217 WLED driver

The TPS65217 chip contains a boost converter and current sinks which can be
used to drive LEDs for use as backlights. Expose this functionality via the
backlight API.

Tested on an AM335x based custom board with a single WLED string, using
different values for ISEL and FDIM (though it would be hard to tell the
difference except for the value in WLEDCTRL1). Both instantiation through the
device tree and by passing platform data have been tested. Testing has been
done with an Androidized 3.2 kernel from the rowboat project. Koen Kooi
reported the driver to be working on a Beaglebone board with LCD3 cape

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

pwm-backlight: Add rudimentary device tree support

This commit adds very basic support for device tree probing. Currently,
only a PWM and a list of distinct brightness levels can be specified.
Enabling or disabling backlight power via GPIOs is not yet supported.

Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

drivers/tosa: driver needs I2C and SPI to compile

This driver requires both SPI and I2C to build.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

backlight: add LM3533 backlight driver

Add sub-driver for the backlights on National Semiconductor / TI LM3533
lighting power chips.

The chip provides 256 brightness levels and ambient-light-sensor and pwm
input control.

[akpm@linux-foundation.org: fix warning]
[akpm@linux-foundation.org: fix the type of `mode']
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Rob Landley <rob@landley.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add driver for DA9052/53 PMIC v1

DA9052/53 PMIC has capability to supply power for upto 3 banks of 6
white serial LEDS. It can also control intensity of independent banks
and to drive these banks boost converter will provide up to 24V and
forward current of max 50mA.

This patch allows to control intensity of the individual WLEDs bank
through DA9052/53 PMIC.

This patch is functionally tested on Samsung SMDKV6410.

Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: fix ot200_bl build

Fix build error when GPIO_CS5535 is not enabled:

drivers/built-in.o: In function `ot200_backlight_probe':
ot200_bl.c:(.text+0x205bf): undefined reference to `cs5535_gpio_set'
ot200_bl.c:(.text+0x205d1): undefined reference to `cs5535_gpio_set'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add support for Pandora backlight

Add support for pandora (openpandora.org) backlight.

It might look like all this could be done using pwm_bl.c instead, but
there is a need of special programming sequence when turning on the LED
driver chip or else it will misbehave. Doing this using pwm_bl.c would
require to use some register programming and pwm functions from platform
code, and ARM maintainers are allergic to driver-like code in /arch/arm
nowadays. The PMIC PWM driver is currently missing too, so pwm_bl.c
can't be used anyway.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add driver for Bachmann's ot200

Add backlight driver for Bachmann's ot200 visualisation device. The
driver uses MFGPT 7 of CS5535 silicon to regulate the backlight.

[akpm@linux-foundation.org: remove redundant test of `brightness']
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: new backlight driver for LP855x devices

THis driver supports TI LP8550/LP8551/LP8552/LP8553/LP8556 backlight
devices.

The brightness can be controlled by the I2C or PWM input. The lp855x
driver provides both modes. For the PWM control, pwm-specific functions
can be defined in the platform data. And some information can be read
via the sysfs(lp855x device attributes).

For details, please refer to Documentation/backlight/lp855x-driver.txt.

[axel.lin@gmail.com: add missing mutex_unlock in lp855x_read_byte() error path]
[axel.lin@gmail.com: check platform data in lp855x_probe()]
[axel.lin@gmail.com: small cleanups]
[dan.carpenter@oracle.com: silence a compiler warning]
[axel.lin@gmail.com: use id->driver_data to differentiate lp855x chips]
[akpm@linux-foundation.org: simplify boolean return expression]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: remove ADX backlight device support

Support for the Avionic Design Xanthos backlight device got added in
commit 3b96ea9ef8 ("backlight: Add support for the Avionic Design Xanthos
backlight device."). That support depends on ARCH_PXA_ADX. The code that
should have provided that Kconfig symbol never got submitted. It has
never been possible to even build this driver. Remove it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/aat2870_bl.c: make it buildable as a module

i386 allmodconfig:

drivers/built-in.o: In function `aat2870_bl_remove':
aat2870_bl.c:(.text+0x414f9): undefined reference to `backlight_device_unregister'
drivers/built-in.o: In function `aat2870_bl_probe':
aat2870_bl.c:(.text+0x418fc): undefined reference to `backlight_device_register'
aat2870_bl.c:(.text+0x41a31): undefined reference to `backlight_device_unregiste

Cc: Jin Park <jinyoungp@nvidia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Add AAT2870 backlight driver

Add backlight driver for AnalogicTech AAT2870.

Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

backlight: add ams369fg06 amoled driver

Add the ams369fg06 amoled panel driver. The ams369fg06 amoled panel (480
x 800) driver uses 3-wired SPI inteface. The brightness can be controlled
by gamma setting of amoled panel.

[sfr@canb.auug.org.au: fix build error]
[axel.lin@gmail.com: unregister backlight device when unloading the module]
[axel.lin@gmail.com: staticize ams369fg06_shutdown]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: anish singh <anish198519851985@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: new driver for the ADP8870 backlight devices

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: apple_bl depends on ACPI

apple_bl uses ACPI interfaces (data & code), so it should depend on ACPI.

drivers/video/backlight/apple_bl.c:142: warning: 'struct acpi_device' declared inside parameter list
drivers/video/backlight/apple_bl.c:142: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/video/backlight/apple_bl.c:201: warning: 'struct acpi_device' declared inside parameter list
drivers/video/backlight/apple_bl.c:215: error: variable 'apple_bl_driver' has initializer but incomplete type
drivers/video/backlight/apple_bl.c:216: error: unknown field 'name' specified in initializer
...

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mbp_nvidia_bl: rename to apple_bl

It works on hardware other than Macbook Pros, and it works on GPUs other
than Nvidia. It should even work on iMacs, so change the name to match
reality more precisely and include an alias so existing users don't get
confused.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mbp_nvidia_bl: remove DMI dependency

This driver only has to deal with two different classes of hardware, but
right now it needs new DMI entries for every new machine. It turns out
that there's an ACPI device that uniquely identifies Apples with backlights,
so this patch reworks the driver into an ACPI one, identifies the hardware
by checking the PCI vendor of the root bridge and strips out all the DMI
code. It also changes the config text to clarify that it works on devices
other than Macbook Pros and GPUs other than nvidia.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/vidfeo/backlight: ld9040 amoled driver support

Add a ld9040 amoled panel driver.

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Add pcf50633 backlight driver

This patch adds a backlight driver for controlling the pcf50633 LED module.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: add S6E63M0 AMOLED LCD Panel driver

This is S6E63M0 AMOLED LCD Panel(480x800) driver using 3-wired SPI
interface also almost features for lcd panel driver has been implemented
in here. and I added new structure common for all the lcd panel drivers
to include/linux/lcd.h file.

LCD Panel driver needs interfaces for controlling device power such as
power on/off and reset. these interfaces are device specific so it should
be implemented to machine code at this time, we should create new
structure for registering these functions as callbacks and also a header
file for that structure and finally registered callback functions would be
called by lcd panel driver. such header file(including new structure for
lcd panel) would be added for all the lcd panel drivers.

If anyone provides common structure for registering such callback
functions then we could reduce unnecessary header files for lcd panel. I
thought that suitable anyone could be include/linux/lcd.h so a new
lcd_platform_data structure was added there.

[akpm@linux-foundation.org: coding-style fixes]
[randy.dunlap@oracle.com: fix s6e63m0 kconfig]
[randy.dunlap@oracle.com: fix device attribute functions return types]
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: adp8860: add support for ADP8861 & ADP8863

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Add Cirrus EP93xx backlight driver

The EP9307, EP9312, and EP9315 processors include a framebuffer
peripheral. This peripheral has a dedicated pwm output called
BRIGHT that can be used to control the backlight on an LCD.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: new driver for the ADP8860 backlight parts

The ADP8860 combines a programmable backlight LED charge pump driver with
automatic phototransistor control.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Kconfig cleanup

Cleanup the "depends on" logic by wrapping the affected config options in
appropriate if/endif blocks.

Remove all the "default n" since that is the default default.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Add Epson L4F00242T03 LCD driver

The Epson LCD L4F00242T03 is mounted on the Freescale i.MX31 PDK board.
Based upon Marek Vasut work in l4f00242t03.c, this driver provides
basic init and power on/off functionality for this device through the
sysfs lcd interface.

Unfortunately Datasheet for this device are not available and
all the control sequences sent to the display were copied from the
freescale driver that in the i.MX31 Linux BSP.

As in the i.MX31PDK board the core and io suppliers are voltage
regulators, that functionality is embedded here, but not strict.

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Enable max8925 backlight

Enable max8925 backlight sub device.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

backlight: Enable backlight in 88pm860x

At most, three backlight device can be supported in 88pm860x driver.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

backlight: new driver for ADP5520/ADP5501 MFD PMICs

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Add support for the Avionic Design Xanthos backlight device.

This patch adds support for the backlight device found on Avionic Design
Xanthos-based boards.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: spi driver for LMS283GF05 LCD

ADd support for the SPI part of LMS283GF05 LCD. The LCD uses SPI for
initialization and powerdown sequences. No further defails are specified
in the datasheet about the initialization/powerdown sequence, just the
magic numbers that have to be sent over SPI bus. This LCD can be found in
the Aeronix Zipit Z2 handheld.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Add WM831x backlight driver

The WM831x series of PMICs provide DC-DC boost convertors and current
sinks which can be used together to drive LEDs for use as backlights.
Expose this functionality via the backlight API.

Since when used in this configuration the current sink and boost
convertor are very tightly coupled with a multi-stage startup for
the current sink which overlaps with the boost convertor startup
this driver bypasses the regulator API. Machine inititialisation
is responsible for ensuring that the regulators are not accessed
via both APIs.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

[ARM] 5614/1: at91: atmel_lcdfb: add at91sam9g10 support to atmel LCD driver

Modify atmel LCD driver: atmel_lcdfb for at91sam9g10. This add a clock
management equivalent to at91sam9261.

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

backlight: Adds HP Jornada 700 series backlight driver

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Add HP Jornada 700 series LCD driver

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: Rename the corgi backlight driver to generic

The corgi backlight driver is really generic code. This rename makes
this a lot clearer and completes the partial rename made a while ago.

Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: add support for Toppoly TDO35S series to tdo24m lcd driver

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

[ARM] pxa: corgi backlight driver should not select ssp drivers

Resolves build errors with eseries and magician defconfigs (which
make use of the corgi backlight driver.)

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig

Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.

This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.

Signed-off-by: Eric Miao <eric.miao@marvell.com>

backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC

[akpm@linux-foundation.org: coding-style fixes]
[rpurdie@linux.intel.com: minor tweaks]
Signed-off-by: Claudio Nieder <private@claudio.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: da903x: Add backlight driver for DA9030/DA9034

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

backlight: add support for Sharp SL-6000 LCD and backlight drivers

On Sharp SL-6000 lcd/backlight is a bit complex, so add two drivers
one for lcd-driving chip, other one for dac regulating the backlight
LEDS.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>

lcd: add support for Toppoly TDO24M series LCD panels

This type of LCD panel can be found on PXA3xx/Littleton platforms.
Add LCD device and SPI-based driver for this.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

lcd: add SPI-based LCD and backlight driver for SHARP corgi/spitz

The driver is based on different source files including corgi_ssp.c,
corgi_lcd.c and corgi_bl.c, previously authored by Richard Purdie
and many others.

The LCD and Backlight device actually share the same SPI device, so
they are made into this single driver.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

fbdev: LCD backlight driver using Atmel PWM driver

This patch adds a platform driver using the ATMEL PWM driver to control a
backlight which requires a PWM signal and optional GPIO signal for discrete
on/off signal. It has been tested on Favr-32 board from EarthLCD.

The driver is configurable by supplying a struct with the platform data. See
the include/linux/atmel-pwm-bl.h for details.

The board code for Favr-32 will be submitted to the AVR32 kernel list.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lcd: add platform_lcd driver

Add a platform_lcd driver to allow boards with simple lcd power controls
to register themselves easily.

[akpm@linux-foundation.org: build fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: add support for the ILI9320 video display controller

Provide support for the ILI9320 display controller chip which is found in
many LCD displays. Included with this is support for an example LCD using
this chip, the VGG2432A4.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Add Nvidia-based Apple Macbook Pro backlight driver

Nvidia-based Apple Macbook Pros don't appear to handle backlight control
through the graphics card registers or ACPI, but instead trigger changes
via SMI calls. This driver registers a generic backlight device that
lets existing userspace deal with it. Code derived from Julien Blache's
Pommed application.

Signed-off-by: Julien Blache <jb@jblache.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

[ARM] pxa: add generic PWM backlight driver

Patch mostly from Eric Miao, with minor edits by rmk to convert
Eric's driver to a generic PWM-based backlight driver.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

backlight: Add OMAP1 PWL backlight driver

This adds the OMAP1 PWL-based LCD backlight driver. It's been in the OMAP
tree for some time. Note that OMAP2 can do similar things with the generic
timers which have PWM outputs. Such timers are more generic than the PWL
found on OMAP1 chips, but have a different EMI profile because they aren't
driven by a pseudorandom number generator.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

atmel_lcdfb: backlight control

On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.

This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.

Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.

[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Convert corgi backlight driver into a more generic driver

Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

backlight: Add Samsung LTV350QV LCD driver

This patch adds support for powering on and off the Samsung LTV350QV LCD
panel via SPI. The driver responds to framebuffer power management, it
powers off the panel on reboot/halt/poweroff. It can also be controlled
through sysfs. The panel is powered up when the module is loaded, and off
when the module is unloaded. Verified on AVR32 STK1000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

backlight: Fix order of Kconfig entries

Switch the order of LCD_CLASS_DEVICE and BACKLIGHT_CLASS_DEVICE,
so that it's possible to insert LCD devices without borking the
dependency displays of xconfig and other config tools.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

vmlfb: framebuffer driver for Intel Vermilion Range

Add the Intel Vermilion Range framebuffer support.

Signed-off-by: Alan Hourihane <alanh@tungstengraphics.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: Fix Kconfig entries

Currently its possible to build the backlight core as a module yet
compile the drivers into the kernel which gives missing symbols.

Fix.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

backlight: Add Frontpath ProGear HX1050+ driver

Add control of LCD backlight for Frontpath ProGear HX1050+.
Patch is based on http://downloads.sf.net/progear/progear-lcd-0.2.tar.gz
driver by M Schacht.

Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>

[PATCH] fbdev: statically link the framebuffer notification functions

The backlight and lcd subsystems can be notified by the framebuffer layer
of blanking events. However, these subsystems, as a whole, can function
independently from the framebuffer layer. But in order to enable to the
lcd and backlight subsystems, the framebuffer has to be compiled also,
effectively sucking in a huge amount of unneeded code.

To prevent dependency problems, separate out the framebuffer notification
mechanism from the framebuffer layer and permanently link it to the kernel.

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] backlight: Fix Kconfig dependency

CONFIG_FB = m and CONFIG_{BACKLIGHT:LCD}_CLASS_DEVICE = y is possible
resulting in link errors. Fix by making backlight and lcd class also depend
on FB

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] backlight: LOCOMO Backlight Driver updates

Add backlight intensity control to the LOCOMO lcd/backlight driver using the
backlight class and add basic power management support.

This is a reimplementation and improvement of patches by John Lenz and Pavel
Machek

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] backlight: corgi_bl: Generalise to support other Sharp SL hardware

Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure. This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.

Also change the spinlock to a mutex (the spinlock is overkill).

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] video: hp680 backlight driver

This adds support for the hp680 backlight, as found in the hp6xx series of
sh devices.

Signed-off-by: Andriy Skulysh <askulysh@image.kiev.ua>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!