ucsi_ccg: Refine the UCSI Interrupt handling

With the Cypress CCGx Type-C controller the following error is
sometimes observed on boot:
[ 16.087147] ucsi_ccg 1-0008: failed to reset PPM!
[ 16.087319] ucsi_ccg 1-0008: PPM init failed (-110)

When the above timeout occurs the following happens:
1. The function ucsi_reset_ppm() is called to reset UCSI controller.
This function performs an async write to start reset and then
polls for completion.
2. An interrupt occurs when the reset completes. In the interrupt
handler, the OPM field in the INTR_REG is cleared and this clears
the CCI data in the PPM. Hence, the reset completion status is
cleared.
3. The function ucsi_reset_ppm() continues to poll for the reset
completion, but has missed the reset completion event and
eventually timeouts.

In this patch, we store CCI when handling the interrupt and make
reading after async write gets the correct value.

To align with the CCGx UCSI interface guide, this patch updates the
driver to copy CCI and MESSAGE_IN before they are reset when UCSI
interrupt acknowledged.

When a new command is sent, the driver will clear the old CCI to avoid
ucsi_ccg_read() getting wrong CCI after ucsi_ccg_async_write() when
the UCSI interrupt is not handled.

Finally, acking the UCSI_READ_INT interrupt before calling complete()
in ISR to ensure that the ucsi_ccg_sync_write() would wait for the
interrupt handling to complete.

Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240126030115.3791554-1-haotienh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: Add Displayport Alternate Mode 2.1 Support

Displayport Alternate mode 2.1 requires configuration for additional
cable details such as signalling for cable, UHBR13.5 Support, Cable type
and DPAM version.
These details can be used with mux drivers to configure SOP DP
configuration for Displayport Alternate mode 2.1.
This change also includes pertinent cable signalling support in displayport
alternate mode.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20230920023243.2494410-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

While touching hd3ss3220.c fix a minor white space issue in the
definition of struct hd3ss3220_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517181528.167115-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi_ccg: Add OF support

Add device-tree support for the Cypress CCG UCSI driver. The device-tree
binding for the Cypress CCG device uses the standard device-tree
'firmware-name' string property to indicate the firmware build that is
used.

The NVIDIA GPU I2C driver has been updated to use an ACPI string
property that is also named 'firmware-build' and given that this was the
only users of the 'ccgx,firmware-build' property, we can now remove
support for this legacy property.

Signed-off-by: Wayne Chang <waynec@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230131175748.256423-4-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi/ucsi_ccg: Convert to i2c's .probe_new()

The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-584-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra

Firmware built for Tegra doesn't support UCSI ALT command and has known
issue of reporting wrong capability info.

This commit disables UCSI ALT support when reading the capability on
Tegra.

Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220928150840.3804313-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

ucsi_ccg: ACPI based I2c client enumeration for AMD ASICs

Some of the AMD platforms have Cypress CCGX PD controller connected
to system I2C i.e designware I2C controller. Added support to enumerate
the CCGX client by adding ACPI ID to the firmware.

Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20220526063305.3144352-3-Sanket.Goswami@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ucsi_ccg: Do not hardcode interrupt polarity and type

The current implementation supports only Level trigger with ACTIVE HIGH,
which is overriding level and polarity set by the ACPI table, hence
implement the common utility function to manage irq requests.

Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20220526063305.3144352-2-Sanket.Goswami@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ucsi_ccg: Check DEV_INT bit only when starting CCG4

CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.

The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.

Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi_ccg: workaround for NVIDIA test device

NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for
VirtualLink DP mode and vdo=0x3 for NVIDIA test mode. NVIDIA
test device FTB (Function Test Board) reports altmode list with
vdo=0x3 first and then vdo=0x1. The list is:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x3
0x955 0x1

Current logic to assign mode value is based on order
in altmode list. This causes a mismatch of CON and SOP altmodes
since NVIDIA GPU connector has order of vdo=0x1 first and then
vdo=0x3. Fixing this by changing the order of vdo values
reported by NVIDIA test device. the new list will be:

SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x1085
0x955 0x3

Also NVIDIA VirtualLink (svid 0x955) uses pin E for display mode.
NVIDIA test device reports vdo of 0x1 so make sure vdo values
always have pin E assignement.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200310121912.57879-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ucsi: ccg: disable runtime pm during fw flashing

Ucsi ppm is unregistered during fw flashing so disable
runtime pm also and reenable after fw flashing is completed
and ppm is re-registered.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200217144913.55330-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: add support for separate DP altmode devices

CCGx controller used on NVIDIA GPU card has two separate display
altmode for two DP pin assignments. UCSI specification doesn't
prohibits using separate display altmode.

Current UCSI Type-C framework expects only one display altmode for
all DP pin assignment. This patch squashes two separate display
altmode into single altmode to support controllers with separate
display altmode. We first read all the alternate modes of connector
and then run through it to know if there are separate display
altmodes. If so, it prepares a new port altmode set after squashing
two or more separate altmodes into one.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230133431.63445-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: Move to the new API

Replacing the old "cmd" and "sync" callbacks with an
implementation of struct ucsi_operations. The interrupt
handler will from now on read the CCI (Command Status and
Connector Change Indication) register, and call
ucsi_connector_change() function and/or complete pending
command completions based on it.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-14-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: Remove run_isr flag

The "run_isr" flag is used for preventing the driver from
calling the interrupt service routine in its runtime resume
callback when the driver is expecting completion to a
command, but what that basically does is that it hides the
real problem. The real problem is that the controller is
allowed to suspend in the middle of command execution.

As a more appropriate fix for the problem, using autosuspend
delay time that matches UCSI_TIMEOUT_MS (5s). That prevents
the controller from suspending while still in the middle of
executing a command.

This fixes a potential deadlock. Both ccg_read() and
ccg_write() are called with the mutex already taken at least
from ccg_send_command(). In ccg_read() and ccg_write, the
mutex is only acquired so that run_isr flag can be set.

Fixes: f0e4cd948b91 ("usb: typec: ucsi: ccg: add runtime pm workaround")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191004100219.71152-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: typec: ucsi_ccg: convert i2c driver to use dev_groups

The driver core now supports the option to automatically create and
remove any needed sysfs attribute files for a driver when the device is
bound/removed from it. Convert the uscsi_ccg code to use that instead
of trying to create sysfs files "by hand".

Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190805193636.25560-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: Fix uninitilized symbol error

Fix smatch error:
drivers/usb/typec/ucsi/ucsi_ccg.c:975 ccg_fw_update() error: uninitialized symbol 'err'.

Fixes: 5c9ae5a87573 ("usb: typec: ucsi: ccg: add firmware flashing support")
Cc: stable@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190801075512.24354-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: add runtime pm workaround

Cypress USB Type-C CCGx controller firmware version 3.1.10
(which is being used in many NVIDIA GPU cards) has known issue of
not triggering interrupt when a USB device is hot plugged to runtime
resume the controller. If any GPU card gets latest kernel with runtime
pm support but does not get latest fixed firmware then also it should
continue to work and therefore a workaround is required to check for
any connector change event.

The workaround is that i2c bus driver will call pm_request_resume()
to runtime resume ucsi_ccg driver. CCG driver will call the ISR
for any connector change event for NVIDIA GPU card and only if it has
old CCG firmware with the known issue.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

usb: typec: ucsi: ccg: enable runtime pm support

The change enables runtime pm support to UCSI CCG driver.
Added ucsi_resume() function to enable notification after
system reusme. Exported both ucsi_resume() and ucsi_send_command()
symbols in ucsi.c for modular build.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

usb: typec: ucsi: ccg: fix memory leak in do_flash

In case memory resources for *fw* were successfully allocated,
release them before return.

Addresses-Coverity-ID: 1445499 ("Resource leak")
Fixes: 5c9ae5a87573 ("usb: typec: ucsi: ccg: add firmware flashing support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: fix missing unlock on error in ccg_cmd_write_flash_row()

Add the missing unlock before return from function ccg_cmd_write_flash_row()
in the error handling case.

Fixes: 5c9ae5a87573 ("usb: typec: ucsi: ccg: add firmware flashing support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: add firmware flashing support

CCGx has two copies of the firmware in addition to the bootloader.
If the device is running FW1, FW2 can be updated with the new version.
Dual firmware mode allows the CCG device to stay in a PD contract and
support USB PD and Type-C functionality while a firmware update is in
progress.

First we read the currently flashed firmware version of both
primary and secondary firmware and then compare it with
version of firmware file to determine if flashing is required.

Command framework is added to support sending commands to CCGx
controller. We wait for response after sending the command and then
read the response from RAB_RESPONSE register.

Below commands are supported,
- ENTER_FLASHING
- RESET
- PDPORT_ENABLE
- JUMP_TO_BOOT
- FLASH_ROW_RW
- VALIDATE_FW

Command specific mutex lock is also added to sync between driver
and user threads.

PD port number information is added which is required while sending
PD_PORT_ENABLE command

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
[ heikki: Added ABI documentation. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: ccg: add get_fw_info function

Function is to get the details of ccg firmware and device version.
It will be useful in debugging and also during firmware update.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: add support for Cypress CCGx

Latest NVIDIA GPU cards have a Cypress CCGx Type-C controller
over I2C interface.

This UCSI I2C driver uses I2C bus driver interface for communicating
with Type-C controller.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>