usb: musb: Use read_poll_timeout()

Use read_poll_timeout() instead of open coding it.
In the same time, fix the typo in the error message.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710094645.42111-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM/musb: omap2: Remove global GPIO numbers from TUSB6010

The TUSB6010 (MUSB) device is picking up some GPIO lines
hardcoded by number and passing on to the TUSB6010 device
when registering it.

Instead of nasty workarounds, provide a GPIO descriptor
table and then make the TUSB6010 MUSB glue driver pick up
the GPIO lines directly, convert it to an IRQ and pass down
to the MUSB driver. OMAP2 is the only system using the
TUSB6010.

Stash the GPIO descriptors in the glue layer and use
then to power up and down the TUSB6010 on-demand, instead
of using boardfile callbacks.

Since the OMAP2 boards are the only boards using the
.set_power() and .board_set_power() callbacks, we can
just delete them as the power is now handled directly
in the TUSB6010 glue code.

Cc: Bin Liu <b-liu@ti.com>
Cc: linux-usb@vger.kernel.org
Fixes: 92bf78b33b0b ("gpio: omap: use dynamic allocation of base")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

usb: musb: tusb6010: Convert to platform remove callback returning void

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230405141009.3400693-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb/musb: fix repeated words in comments

Delete the redundant word 'mode'.
Delete the redundant word 'than'.

Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220716134457.46535-1-yuanjilin@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: tusb6010: check return value after calling platform_get_resource()

It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210915034925.2399823-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: tusb6010: uninitialized data in tusb_fifo_write_unaligned()

This is writing to the first 1 - 3 bytes of "val" and then writing all
four bytes to musb_writel(). The last byte is always going to be
garbage. Zero out the last bytes instead.

Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210916135737.GI25094@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: Fix fall-through warnings for Clang

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break/return/fallthrough
statements instead of letting the code fall through to the next
case.

Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/a76da7ca5b4f41c13d27b298accb8222d0b04e61.1605896060.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

usb: musb: tusb6010: fix a possible missing data type replacement

Replace "unsigned" to "u32" for checkpatch fix to tusb_writeb().

Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-9-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: Add musb_clearb/w() interface

Delete the const attribute of addr parameter in readb/w/l hooks, these
changes are for implementing clearing W1C registers.
Replace musb_readb/w with musb_clearb/w to clear the interrupt status.

While at here, change some unsigned type to u32 to fix checkpatch.pl
warnings.

Signed-off-by: Min Guo <min.guo@mediatek.com>
[b-liu@ti.com: fix checkpatch.pl warnings.]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-23-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: musb: Remove redundant license text

Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: add SPDX identifiers to all remaining files in drivers/usb/

It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: Convert timers to use timer_setup()

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Instead of a per-device static timer variable, a spare timer "dev_timer"
is added to the musb structure for devices to use for their per-device
timer.

Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well

Handle the DMA TX in a similar way as we do for the RX: in the DMA
completion callback.

Since we are no longer using DMA completion interrupt for the TX we can as
wall keep these interrupts disabled, but keep the handler for debug
purposes.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks

When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: Fix PM for hub disconnect

With a USB hub disconnected, devctl can be 0x19 for about a second
on am335x and will stay forever on at least omap3. And we get no
further interrupts when devctl session bit clears. This keeps
PM runtime active.

Let's fix the issue by polling devctl until the session bit clears
or times out. We can do this by making musb->irq_work into
delayed_work.

And with the polling implemented, we can now also have the quirk
for invalid VBUS it to avoid disconnecting too early while VBUS
is ramping up.

Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime
PM for musb-core")
Fixes: 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: Set up function pointers for DMA

Set up function pointers for DMA so get closer to
being able to build in all the DMA engines.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: Fix up DMA related macros

Pass struct musb to tusb_dma_omap() and is_cppi_enabled(),
and add macros for the other DMA controllers. Populate the
platform specific quirks with the DMA type and use it during
runtime.

Note that platform glue layers with no custom DMA code are
tagged with MUSB_DMA_INVENTRA which may have a chance of
working. Looks like the defconfigs for these use PIO_ONLY,
so this should not break existing configs.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: Change end point selection to use new IO access

This allows the endpoints to work when multiple MUSB glue
layers are built in.

Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: Change to use new IO access

Change to use new IO access. This allows us to build in multiple
MUSB glue layers.

[ balbi@ti.com : switch to EXPORT_SYMBOL_GPL()
fix long lines ]

Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: Populate new IO functions for tusb6010

Let's populate the new IO functions for tusb6010 but not use
them yet.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: move the OTG state from the USB PHY to the OTG structure

Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.

[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]

Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: delete unnecessary 'out of memory' messages

The memory subsystem has already had similar message for it.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: hub: rename khubd to hub_wq in documentation and comments

USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.

This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:

Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c

Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: tusb6010: Introduce the use of the managed version of kzalloc

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecesary labels are removed and linux/device.h is
added to make sure the devm_*() routine declarations are unambiguously
available.

The following Coccinelle semantic patch was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: Use musb->tusb_revision instead of tusb_get_revision call.

The value of the revision is stored in musb->tusb_revision,
so don't re-read it every time.
Exporting tusb_get_revision is not needed anymore,
so the dependency loop between tusb6010 and tusb6010_omap is resolved.

Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: Add tusb_revision to struct musb to store the revision.

Add field to store tusb6010 revision value. Read the revision at
the startup and store to the variable.

Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: phy: generic: allow multiples calls to usb_phy_generic_register()

it's now very easy to return a platform_device pointer
and have the caller pass it as argument when calling
usb_phy_generic_unregister().

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: move usb_phy_generic_{un,}register calls to probe()/remove()

This patch is in preparation to supporting
calling those functions multiple times.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: phy: rename <linux/usb/usb_phy_gen_xceiv.h> to <linux/usb/usb_phy_generic.h>

now that all functions match the driver name,
the only missing piece is to rename the header
file itself.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: phy: rename usb_nop_xceiv to usb_phy_generic

no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: delete non-required instances of include <linux/init.h>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks

Use platform_device_register_full() for those drivers which can, to
avoid messing directly with DMA masks. This can only be done when
the driver does not need to access the allocated musb platform device
from within its callbacks, which may be called during the musb
device probing.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

usb: musb: use platform_device_register_full() to avoid directly messing with dma masks

Use platform_device_register_full() for those drivers which can, to
avoid messing directly with DMA masks. This can only be done when
the driver does not need to access the allocated musb platform device
from within its callbacks, which may be called during the musb
device probing.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv

The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: fix resource passed from glue layer to musb

some MUSB incarnations, such as those governed by
omap2430.c and tusb6010.c, have three resources, not
two.

Fix the bug created by commit 09fc7d2 (usb: musb:
fix incorrect usage of resource pointer) where only
two of the three resources would be passed to musb_core.c

[ balbi@ti.com : add tusb6010.c to original patch ]

Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: fix incorrect usage of resource pointer

We can't simply pass the resource pointer from our
device down to our children, otherwise module
reinsertion will not work as the resource will
continue to be marked as busy.

Fix it by building a proper struct resource for
our child musb device.

Tested-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: otg: prefix otg_state_string with usb_

all other functions under drivers/usb/ start
with usb_, let's do the same thing.

This patch is in preparation for moving otg_state_string
to usb-common.c and deleting otg.c completely.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: fix dependency on transceiver driver

This patch let glue driver return -EPROBE_DEFER if the transceiver
is not readly, so we can support defer probe on musb to fix the
below error on 3.7-rc5 if transceiver drivers are built as module:

[ 19.052490] unable to find transceiver of type USB2 PHY
[ 19.072052] HS USB OTG: no transceiver configured
[ 19.076995] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -19
[ 19.089355] musb-hdrc: probe of musb-hdrc.0.auto rejects match -19
[ 19.096771] driver: 'musb-omap2430': driver_bound: bound to device 'musb-omap2430'
[ 19.105194] bus: 'platform': really_probe: bound device musb-omap2430 to driver musb-omap2430
[ 19.174407] bus: 'platform': add driver twl4030_usb
[ 19.179656] bus: 'platform': driver_probe_device: matched device twl4030_usb with driver twl4030_usb
[ 19.202270] bus: 'platform': really_probe: probing driver twl4030_usb with device twl4030_usb
[ 19.214172] twl4030_usb twl4030_usb: HW_CONDITIONS 0xc0/192; link 3
[ 19.239624] musb-omap2430 musb-omap2430: musb core is not yet ready
[ 19.246765] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 19.254516] driver: 'twl4030_usb': driver_bound: bound to device 'twl4030_usb'
[ 19.263580] bus: 'platform': really_probe: bound device twl4030_usb to driver twl4030_usb

Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: <stable@vger.kernel.org> v3.8
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

musb: tusb6010: use io{read,write}*_rep accessors

The {read,write}s{b,w,l} operations are not defined by all architectures
and are being removed from the asm-generic/io.h interface.

This patch replaces the usage of these string functions in the tusb6010
accessors with io{read,write}{8,16,32}_rep calls instead.

Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usb: remove use of __devexit

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: remove use of __devinit

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: remove use of __devexit_p

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: remove hand-crafted id handling

This replaced the handcrafted id handling by the PLATFORM_DEVID_AUTO
value which should do the same thing.

This patch probably also fixes ux500 because I did not find the "musbid"
variable to remove. And we close a tiny-unlikely race window becuase the
old code gave the id back before device was destroyed in the remove
case.

[ balbi@ti.com : fixed up two failed hunks when applying patch ]

Cc: B, Ravi <ravibabu@ti.com>
Cc: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Cc: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: use platform_device_unregister in tusb_remove()

platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.

Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: use module_platform_driver macro

This patch removes some code duplication by using
module_platform_driver.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: add musb_ida for multi instance support

Added musb_ida in musb_core.c to manage the multi core ids.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: fix error path in tusb_probe()

On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: drop useless board_mode usage

we are compiling the driver always with full OTG
capabilities, so that board_mode trick becomes
useless.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: fix sparse warnings

The following warnings are fixed:

drivers/usb/musb/musb_core.c:357:6: warning: symbol 'musb_otg_timer_func' was not declared. Should it be static?
drivers/usb/musb/musb_core.c:1339:27: warning: incorrect type in initializer (different address spaces)
drivers/usb/musb/musb_core.c:1339:27: expected void *mbase
drivers/usb/musb/musb_core.c:1339:27: got void [noderef] <asn:2>*mregs
drivers/usb/musb/musb_core.c:1347:17: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/musb_core.c:1347:17: expected void [noderef] <asn:2>*addr
drivers/usb/musb/musb_core.c:1347:17: got void *mbase
drivers/usb/musb/musb_core.h:487:27: warning: incorrect type in initializer (different address spaces)
drivers/usb/musb/musb_core.h:487:27: expected void *mbase
drivers/usb/musb/musb_core.h:487:27: got void [noderef] <asn:2>*mregs
drivers/usb/musb/musb_core.h:491:26: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/musb_core.h:491:26: expected void const [noderef] <asn:2>*addr
drivers/usb/musb/musb_core.h:491:26: got void *mbase
drivers/usb/musb/tusb6010.c:270:48: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/musb/tusb6010.c:270:48: expected void [noderef] <asn:2>*buf
drivers/usb/musb/tusb6010.c:270:48: got unsigned char [usertype] *[assigned] buf
drivers/usb/musb/tusb6010.c:164:32: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/tusb6010.c:164:32: expected void *to
drivers/usb/musb/tusb6010.c:164:32: got void [noderef] <asn:2>*buf
drivers/usb/musb/tusb6010.c:172:24: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/tusb6010.c:172:24: expected void *to
drivers/usb/musb/tusb6010.c:172:24: got void [noderef] <asn:2>*[assigned] buf

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: xceiv: create nop-usb-xceiv.h and avoid pollution on otg.h

nop-usb-xceiv was polluting otg.h with its own
function prototypes. Move those prototypes to
a nop-usb-xceiv.h header.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: phy: fix return value check of usb_get_phy

usb_get_phy will return -ENODEV if it's not able to find the phy. Hence
fixed all the callers of usb_get_phy to check for this error condition
instead of relying on a non-zero value as success condition.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: otg: support for multiple transceivers by a single controller

Add a linked list for keeping multiple PHY instances with different
types so that we can have separate USB2 and USB3 PHYs on one single
board. _get_phy_ has been changed so that the controller gets
the transceiver by type. _remove_phy_ has been added to let the phy
be removed from the phy list.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: otg: utils: rename function name in OTG utils

_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: Convert all users to new usb_phy

Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.

Includes fixes from Sascha Hauer.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: Start using struct usb_otg

Use struct usb_otg members with OTG specific functions instead
of usb_phy members.

[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
a compile error on a later patch ]

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: otg: Rename otg_transceiver to usb_phy

This is the first step in separating USB transceivers from
USB OTG utilities.

Includes fixes to IMX code from Sascha Hauer.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: make modules behave better

There's really no point in doing all that
initcall trickery when we can safely let
udev handle module probing for us.

Remove all of that trickery, by moving everybody
to module_init() and making proper use of
platform_device_register() rather than
platform_device_probe().

Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: allow building USB_MUSB_TUSB6010 as a module

Commit 1376d92f9 "usb: musb: allow musb and glue layers to be modules"
made the USB_MUSB_TUSB6010 option modular, but actually building
the driver as a module does not work, so various randconfig builds
actually fail. This changes all code that depends on the
option to also check for modular builds, and exports the necessary
symbols.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: fix compilation

earlier commits have broken compilation of
tusb6010 glue layer, fix it.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: drop a gigantic amount of ifdeferry

the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.

This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb: musb: fix compile error

commit 35a83365da6aa10095c6138cc428c15853409c32
(usb: musb: drop unneeded musb_debug trickery)
introduced a compile error for blackfin and
tusb6010 glue layers. Fix it.

Reported-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: drop unneeded musb_debug trickery

We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:

Documentation/dynamic-debug-howto.txt

for information on how to use that great
infrastructure.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: fix building musb drivers

Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.

Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers: Final irq namespace conversion

Scripted with coccinelle.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

usb: musb: move clock handling to glue layer

musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: pass platform_ops via platform_data

... then we don't need to export any symbols
from glue layer to musb_core.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: tusb6010: give it a context structure

that structure currently only holds a device
pointer to our own platform_device and musb's
platform_device, but soon it will hold pointers
to our clock structures and glue-specific bits
and pieces.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: split tusb6010 to its own platform_driver

Just adding its own platform_driver, not really
using it yet.

When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: make all glue layer export struct musb_platform_ops

preparing to a big refactor on musb code. We need
to be able to compile in all glue layers (or at
least all ARM-based ones) together and have a
working binary.

While preparing for that, we move every glue
layer to export only one symbol, which is
a struct musb_platform_ops, and make all
other functions static.

Later patches will come to allow for compiling
all glue layers together and have a working
binary.

Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: musb: remove board_data parameter from musb_platform_init()

Removed the board_data parameter being
passed to musb_platform_init function
as board_data can be extracted from
device structure which is already member
of musb structure.

Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

USB: MUSB: fix kernel WARNING/oops when unloading module in OTG mode

Since commit 461972d8a4c94bc44f11a13046041c78a7cf18dd (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.

On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: musb: tusb6010: fix compile error with n8x0_defconfig

Drop the unnecessary empty stubs in tusb6010.c and avoid
a compile error when building kernel for n8x0.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb: musb: Set transceiver interface type

Program the OTG_INTERFSEL register based on
transcevier type passed from board file.

Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.

Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb: Fix tusb6010 for DMA API

Commit 18eabe2347ae7a11b3db768695913724166dfb0e introduced
DMA buffer ownership. Fix tusb6010 accordingly. To compile,
also dummy musb_platform_save and restore functions need to
be added.

Also change the order of musb_read_fifo() to happen after
dma_cache_maint to have the DMA operations completed before
moving the remaining unaligned bytes with PIO. The DMA
access and PIO touch different areas of the FIFO, so this
change only makes the code a bit easier to follow.

Tested on n810 and g_ether with variable size ping test.
The test seems to fail for some ping sizes, but that seems to
be a different problem.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: musb: tusb6010: use resource_size

Trivial patch, no functional changes.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

musb: proper hookup to transceiver drivers

Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated. OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.

Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: musb: Remove my email address from few musb related drivers

This email address is going to expire soon and my contribution to musb
is next to zero so remove it.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: musb: sysfs mode updates

Fix three omissions in the "mode" sysfs attribute support:
(a) inability to report errors;
(b) no DaVinci support ... just report an error;
(c) for omap2430, accepting unsupportable values

The 2430 stuff is still odd....

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb: musb: tusb6010: kill compile warning

Add an errno to failing case.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: Add MUSB and TUSB support

This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>