thermal/drivers/tsens: Allow configuring min and max trips

IPQ8074 and IPQ6018 dont support negative trip temperatures and support
up to 204 degrees C as the max trip temperature.

So, instead of always setting the -40 as min and 120 degrees C as max
allow it to be configured as part of the features.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220818220245.338396-3-robimarko@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

thermal/drivers/tsens: Add support for combined interrupt

Despite using tsens v2.3 IP, IPQ8074 and IPQ6018 only have one IRQ for
signaling both up/low and critical trips.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220245.338396-2-robimarko@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

thermal/drivers/tsens: Drop unused define for msm8960

Drop unused define for msm8960 replaced by generic api and reg_field.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-8-ansuelsmth@gmail.com

thermal/drivers/tsens: Replace custom 8960 apis with generic apis

Rework calibrate function to use common function. Derive the offset from
a missing hardcoded slope table and the data from the nvmem calib
efuses.
Drop custom get_temp function and use generic api.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-7-ansuelsmth@gmail.com

thermal/drivers/tsens: Fix bug in sensor enable for msm8960

Device based on tsens VER_0 contains a hardware bug that results in some
problem with sensor enablement. Sensor id 6-11 can't be enabled
selectively and all of them must be enabled in one step.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-6-ansuelsmth@gmail.com

thermal/drivers/tsens: Use init_common for msm8960

Use init_common and drop custom init for msm8960.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-5-ansuelsmth@gmail.com

thermal/drivers/tsens: Add VER_0 tsens version

VER_0 is used to describe device based on tsens version before v0.1.
These device are devices based on msm8960 for example apq8064 or
ipq806x. Add support for VER_0 in tsens.c and set the right tsens feat
in tsens-8960.c file.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-4-ansuelsmth@gmail.com

thermal/drivers/tsens: Convert msm8960 to reg_field

Convert msm9860 driver to reg_field to use the init_common
function.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-3-ansuelsmth@gmail.com

drivers: thermal: tsens: Pass around struct tsens_sensor as a constant

All the sensor data is initialised at init time. Lock it down by passing
it to functions as a constant.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/740f9254484c08d65869df578628eb523c0049ff.1584015867.git.amit.kucheria@linaro.org

drivers: thermal: tsens: De-constify struct tsens_features

struct tsens_features is currently initialized as part of platform data
at compile-time and not modifiable. We now have some usecases in feature
detection across IP versions where it is more flexible to update the
features after probing registers.

Remove const qualifier from tsens_features and the encapsulating
tsens_plat_data.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/2919a72220470366ae11e0bb5330a4ea39838f71.1584015867.git.amit.kucheria@linaro.org

drivers: thermal: tsens: Get rid of id field in tsens_sensor

There are two fields - id and hw_id - to track what sensor an action was
to performed on. This was because the sensors connected to a TSENS IP
might not be contiguous i.e. 1, 2, 4, 5 with 3 being skipped.

This causes confusion in the code which uses hw_id sometimes and id
other times (tsens_get_temp, tsens_get_trend).

Switch to only using the hw_id field to track the physical ID of the
sensor. When we iterate through all the sensors connected to an IP
block, we use an index i to loop through the list of sensors, and then
return the actual hw_id that is registered on that index.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/30206cd47d303d2dcaef87f4e3c7173481a0bddd.1572526427.git.amit.kucheria@linaro.org

drivers: thermal: qcom: tsens: Fix memory leak from qfprom read

memory returned as part of nvmem_read via qfprom_read should be
freed by the consumer once done.
Existing code is not doing it so fix it.

Below memory leak detected by kmemleak
[<ffffff80088b7658>] kmemleak_alloc+0x50/0x84
[<ffffff80081df120>] __kmalloc+0xe8/0x168
[<ffffff80086db350>] nvmem_cell_read+0x30/0x80
[<ffffff8008632790>] qfprom_read+0x4c/0x7c
[<ffffff80086335a4>] calibrate_v1+0x34/0x204
[<ffffff8008632518>] tsens_probe+0x164/0x258
[<ffffff80084e0a1c>] platform_drv_probe+0x80/0xa0
[<ffffff80084de4f4>] really_probe+0x208/0x248
[<ffffff80084de2c4>] driver_probe_device+0x98/0xc0
[<ffffff80084dec54>] __device_attach_driver+0x9c/0xac
[<ffffff80084dca74>] bus_for_each_drv+0x60/0x8c
[<ffffff80084de634>] __device_attach+0x8c/0x100
[<ffffff80084de6c8>] device_initial_probe+0x20/0x28
[<ffffff80084dcbb8>] bus_probe_device+0x34/0x7c
[<ffffff80084deb08>] deferred_probe_work_func+0x6c/0x98
[<ffffff80080c3da8>] process_one_work+0x160/0x2f8

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

drivers: thermal: tsens: Rename variable tmdev

tmdev seems to imply that this is a device pointer when in fact it is
just private platform data for each tsens device. Rename it to priv
improve code readability.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

drivers: thermal: tsens: Rename tsens_device

Rename to tsens_priv to denote that it is private data for each tsens
instance.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

drivers: thermal: tsens: Rename tsens_data

Rename to tsens_plat_data to denote that it is platform-data passed in
at compile-time.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

thermal: tsens: Rename map field in order to add a second address map

The TSENS driver currently only uses a limited set of registers from the TM
address space. So it was ok to map just that set of registers and call it
"map".

We'd now like to map a second set: SROT registers to introduce new
functionality. Rename the "map" field to a more appropriate "tm_map".

The 8960 doesn't have a clear split between TM and SROT registers. To avoid
complicating the data structure, it will switchover to using tm_map for its
maps.

There is no functional change with this patch.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

thermal: tsens: Add SPDX license identifiers

The TSENS drivers use a GPL-2.0 license. Replace with equivalent SPDX
tags and delete the full license text.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

thermal: qcom: remove declare local symbols as static

Trivial: remove the following:
drivers/thermal/qcom/tsens-8916.c:103:24: warning: symbol 'ops_8916' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8996.c:76:24: warning: symbol 'ops_8996' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8974.c:235:24: warning: symbol 'ops_8974' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8960.c:279:24: warning: symbol 'ops_8960' was not declared. Should it be static?

Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

thermal: qcom: tsens-8960: Add support for 8960 family of SoCs

8960 family of SoCs have the TSENS device as part of GCC, hence
the driver probes the virtual child device created by GCC and
uses the parent to extract all DT properties and reuses the GCC
regmap.

Also GCC/TSENS are part of a domain thats not always ON.
Hence add .suspend and .resume hooks to save and restore some of
the inited register context.

Also 8960 family have some of the TSENS init sequence thats
required to be done by the HLOS driver (some later versions of TSENS
do not export these registers to non-secure world, and hence need
these initializations to be done by secure bootloaders)

8660 from the same family has just one sensor and hence some register
offset/layout differences which need special handling in the driver.

Based on the original code from Siddartha Mohanadoss, Stephen Boyd and
Narendran Rajan.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>