scsi: qla4xxx: Convert uses of __constant_cpu_to_<foo> to cpu_to_<foo>

The macros cpu_to_le16() and cpu_to_le32() have special cases for
constants. Their __constant_<foo> versions are not required.

On little endian systems, both cpu_to_le16() and __constant_cpu_to_le16()
expand to the same expression. Same is the case with cpu_to_le32().

On big endian systems, cpu_to_le16() expands to __swab16() which has a
__builtin_constant_p check. Similarly, cpu_to_le32() expands to __swab32().

Consequently these macros can be safely used with constants, and hence all
those uses are converted. This was discovered as a part of a checkpatch
evaluation, looking at all reports of WARNING:CONSTANT_CONVERSION error
type.

Link: https://lore.kernel.org/r/20210716112852.24598-1-dwaipayanray1@gmail.com
Signed-off-by: Dwaipayan Ray <dwaipayanray1@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove an unused function

This was detected by building the kernel with clang and W=1.

Link: https://lore.kernel.org/r/20210415220826.29438-13-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove redundant assignment to variable rval

The variable rval is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is
redundant and can be removed.

Link: https://lore.kernel.org/r/20201204191810.1150995-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")

scsi: qla4xxx: Remove in_interrupt() from qla4_82xx_rom_lock()

qla4_82xx_rom_lock() spins on a certain hardware state until it is
updated. At the end of each spin, if in_interrupt() is true, it does 20
loops of cpu_relax(). Otherwise, it yields the CPU.

While in_interrupt() is ill-defined and does not provide what the name
suggests, it is not needed here: qla4_82xx_rom_lock() is always called
from process context. Below is an analysis of its callers:

- ql4_nx.c: qla4_82xx_rom_fast_read(), all process context callers:
=> ql4_nx.c: qla4_82xx_pinit_from_rom(), GFP_KERNEL allocation
=> ql4_nx.c: qla4_82xx_load_from_flash(), msleep() in a loop

- ql4_nx.c: qla4_82xx_pinit_from_rom(), earlier discussed

- ql4_nx.c: qla4_82xx_rom_lock_recovery(), bound to "isp_operations"
->rom_lock_recovery() hook, which has one process context caller,
qla4_8xxx_device_bootstrap(), with callers:
=> ql4_83xx.c: qla4_83xx_need_reset_handler(), process, msleep()
=> ql4_nx.c: qla4_8xxx_device_state_handler(), multiple msleep()s

- ql4_nx.c: qla4_82xx_read_flash_data(), has cond_resched()

Remove the in_interrupt() check. Mark, qla4_82xx_rom_lock(), and the
->rom_lock_recovery() hook, with "Context: task, can sleep".

Change qla4_82xx_rom_lock() implementation to sleep 20ms, instead of a
schedule(), for each spin. This is more deterministic, and it matches
the other implementations bound to ->rom_lock_recovery().

Link: https://lore.kernel.org/r/20201126132952.2287996-9-bigeasy@linutronix.de
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: <GR-QLogic-Storage-Upstream@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove in_interrupt() from qla4_82xx_idc_lock()

qla4_82xx_idc_lock() spins on a certain hardware state until it is
updated. At the end of each spin, if in_interrupt() is true, it does 20
loops of cpu_relax(). Otherwise, it yields the CPU.

While in_interrupt() is ill-defined and does not provide what the name
suggests, it is not needed here: qla4_82xx_idc_lock() is always called from
process context. Below is an analysis of its callers:

- ql4_nx.c: qla4_82xx_need_reset_handler(), 1-second msleep() in a
loop.

- ql4_nx.c: qla4_82xx_isp_reset(), calls
qla4_8xxx_device_state_handler(), which has multiple msleep()s.

Beside direct calls, qla4_82xx_idc_lock() is also bound to isp_operations
->idc_lock() hook. Other functions which are bound to the same hook,
e.g. qla4_83xx_drv_lock(), also have an msleep(). For completeness, below
is an analysis of all callers of that hook:

- ql4_83xx.c: qla4_83xx_need_reset_handler(), has an msleep()

- ql4_83xx.c: qla4_83xx_isp_reset(), calls
qla4_8xxx_device_state_handler(), which has multiple msleep()s.

- ql4_83xx.c: qla4_83xx_disable_pause(), all process context callers:
=> ql4_mbx.c: qla4xxx_mailbox_command(), msleep(), mutex_lock()
=> ql4_os.c: qla4xxx_recover_adapter(), schedule_timeout() in loop
=> ql4_os.c: qla4xxx_do_dpc(), workqueue context

- ql4_attr.c: qla4_8xxx_sysfs_write_fw_dump(), sysfs bin_attribute
->write() hook, process context

- ql4_mbx.c: qla4xxx_mailbox_command(), earlier discussed

- ql4_nx.c: qla4_8xxx_device_bootstrap(), callers:
=> ql4_83xx.c: qla4_83xx_need_reset_handler(), process, msleep()
=> ql4_nx.c: qla4_8xxx_device_state_handler(), earlier discussed

- ql4_nx.c: qla4_8xxx_need_qsnt_handler(), callers:
=> ql4_nx.c: qla4_8xxx_device_state_handler(), multiple msleep()s
=> ql4_os.c: qla4xxx_do_dpc(), workqueue context

- ql4_nx.c: qla4_8xxx_update_idc_reg(), callers:
=> ql4_nx.c: qla4_8xxx_device_state_handler(), earlier discussed
=> ql4_os.c: qla4_8xxx_error_recovery(), only called by
qla4xxx_pci_slot_reset(), which is bound to PCI ->slot_reset()
process-context hook

- ql4_nx.c: qla4_8xxx_device_state_handler(), earlier discussed

- ql4_os.c: qla4xxx_recover_adapter(), earlier discussed

- ql4_os.c: qla4xxx_do_dpc(), earlier discussed

Remove the in_interrupt() check. Mark, qla4_82xx_idc_lock(), and the
->idc_lock() hook itself, with "Context: task, can sleep".

Change qla4_82xx_idc_lock() implementation to sleep 100ms, instead of a
schedule(), for each spin. This is more deterministic, and it matches other
PCI HW locking functions in the driver.

Link: https://lore.kernel.org/r/20201126132952.2287996-8-bigeasy@linutronix.de
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: <GR-QLogic-Storage-Upstream@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove in_interrupt()

qla4_82xx_crb_win_lock() spins on a certain hardware state until it's
updated. At the end of each spin, if in_interrupt() is true, it does 20
loops of cpu_relax(). Otherwise, it yields the CPU.

The in_interrupt() macro is ill-defined as it does not provide what the
name suggests, and it does not catch the intended use-case here.

qla4_82xx_crb_win_lock() is always invoked with scsi_qla_host::hw_lock
acquired, with disabled interrupts. If the caller is in process context, as
in qla4_82xx_need_reset_handler(), then in_interrupt() will return false
even though it is not allowed to call schedule().

Remove the in_interrupt() check.

Change qla4_82xx_crb_win_lock() specification to a purely atomic
function. Mark it as static, remove its forward declaration, and move it
above its callers. To avoid hammering the PCI bus while spinning, use a 10
micro-second delay instead of cpu_relax().

Link: https://lore.kernel.org/r/20201126132952.2287996-4-bigeasy@linutronix.de
Fixes: f4f5df23bf72 ("[SCSI] qla4xxx: Added support for ISP82XX")
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: <GR-QLogic-Storage-Upstream@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Fix inconsistent format argument type

Fix the following warning:

[drivers/scsi/qla4xxx/ql4_nx.c:3228]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.

Link: https://lore.kernel.org/r/20200930022228.2840587-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi/qla4xxx: Convert to SPDX license identifiers

All files in this driver directory contain the following notice:

See LICENSE.qla4xxx for copyright and licensing details.

LICENSE.qla4xxx can be found in Documentation/scsi/. The file contains:

- A copyright notice

This copyright notice is redundant as all files contain the same
copyright notice already

- A license notice

You may modify and redistribute the device driver code under the
GNU General Public License (a copy of which is attached hereto as
Exhibit A) published by the Free Software Foundation (version 2).

- The full GPLv2 license text

This can be replaced with the corresponding SPDX license identifier
(GPL-2.0-only) in the source files which reference this license
file.

- The full GPLv2 license text

A redundant copy of LICENSES/preferred/GPL-2.0

Remove the notices and add the SPDX license identifier GPL-2.0-only to the
source files.

Finally remove the now redundant LICENSE.qla4xxx file.

Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla4xxx: Supply description for 'code'

Demote other headers which are clearly not kerneldoc.

Fixes the following W=1 kernel build warning(s):

drivers/scsi/qla4xxx/ql4_nx.c:983: warning: Function parameter or member 'ha' not described in 'qla4_82xx_pinit_from_rom'
drivers/scsi/qla4xxx/ql4_nx.c:983: warning: Function parameter or member 'verbose' not described in 'qla4_82xx_pinit_from_rom'
drivers/scsi/qla4xxx/ql4_nx.c:3225: warning: Function parameter or member 'code' not described in 'qla4_8xxx_uevent_emit'
drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'ha' not described in 'qla4_82xx_read_optrom_data'
drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'buf' not described in 'qla4_82xx_read_optrom_data'
drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'offset' not described in 'qla4_82xx_read_optrom_data'
drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'length' not described in 'qla4_82xx_read_optrom_data'

Link: https://lore.kernel.org/r/20200721164148.2617584-34-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove three set but unused variables

Fixes the following W=1 kernel build warning(s):

drivers/scsi/qla4xxx/ql4_nx.c: In function ‘qla4_84xx_minidump_process_rddfe’:
drivers/scsi/qla4xxx/ql4_nx.c:2648:23: warning: variable ‘data_size’ set but not used [-Wunused-but-set-variable]
2648 | uint32_t poll, mask, data_size, modify_mask;
| ^~~~~~~~~
drivers/scsi/qla4xxx/ql4_nx.c: In function ‘qla4_84xx_minidump_process_rdmdio’:
drivers/scsi/qla4xxx/ql4_nx.c:2745:11: warning: variable ‘poll’ set but not used [-Wunused-but-set-variable]
2745 | uint32_t poll, mask;
| ^~~~
drivers/scsi/qla4xxx/ql4_nx.c: In function ‘qla4_84xx_minidump_process_pollwr’:
drivers/scsi/qla4xxx/ql4_nx.c:2816:47: warning: variable ‘mask’ set but not used [-Wunused-but-set-variable]
2816 | uint32_t addr1, addr2, value1, value2, poll, mask, r_value;
| ^~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-33-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

cross-tree: phase out dma_zalloc_coherent()

We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.

This change was generated with the following Coccinelle SmPL patch:

@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@

-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)

Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>

treewide: kmalloc() -> kmalloc_array()

The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:

kmalloc(a * b, gfp)

with:
kmalloc_array(a * b, gfp)

as well as handling cases of:

kmalloc(a * b * c, gfp)

with:

kmalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

kmalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

kmalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
kmalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kmalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
kmalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kmalloc
+ kmalloc_array
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
kmalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
kmalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kmalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
kmalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
kmalloc(C1 * C2 * C3, ...)
|
kmalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
kmalloc(sizeof(THING) * C2, ...)
|
kmalloc(sizeof(TYPE) * C2, ...)
|
kmalloc(C1 * C2 * C3, ...)
|
kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- (E1) * E2
+ E1, E2
, ...)
|
- kmalloc
+ kmalloc_array
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kmalloc
+ kmalloc_array
(
- E1 * E2
+ E1, E2
, ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>

scsi: qla4xxx: Move an array from a .h into a .c file

This patch does not change any functionality but slightly reduces
the size of the compiled kernel module.

Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Use zeroing allocator rather than allocator/memset

Use dma_zalloc_coherent instead of dma_alloc_coherent followed by memset
0.

Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci

Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: switch to pci_alloc_irq_vectors

And simplify the MSI-X logic in general - just request the two vectors
directly instead of going through an indirection table.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: print MAC and SID via %p[mM][R]

In the kernel we have nice specifier to print MAC by given pointer to
the address in a binary form.

Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Mark symbols static where possible

We get 1 warning when build kernel with W=1:
drivers/scsi/qla4xxx/ql4_nx.c:1846:10: warning: no previous prototype for 'ql4_84xx_ipmdio_rd_reg' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static. This patch marks
this function with 'static'.

Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

move io-64-nonatomic*.h out of asm-generic

These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

qla4xxx: Use pci_enable_msix_exact() instead of pci_enable_msix()

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-By: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla4xxx: Check for correct return status

Check for correct return status in function -
qla4_8xxx_minidump_pex_dma_read

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla4xxx: qla4xxx: Move qla4_8xxx_ms_mem_write_128b to ql4_nx.c

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla4xxx: Added PEX DMA Support for ISP8022 Adapter

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla4xxx: Added new opcodes for 84XX Minidump template

Updated driver with new opcode (RDDFE, RDMDIO and POLLWR) which are
added with latest firmware minidump template

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>

[SCSI] qla4xxx: Reduce rom-lock contention during reset recovery.

Issue:
Driver holds rom-lock for too long during reset recovery.

During adapter reset testing, it was found that the driver
holds the rom-lock for too long, because of which other
drivers fail to acquire the rom-lock, leading to reset
failures.
The primary cause is, in the bootstrap code, while
holding the rom-lock, the driver checks if the peg is
halted, causing a 2 second contention.

Fix:
When a reset recovery starts, the driver deduces the cause, and
sets appropriate flags in watchdog & recover_adapter routines.
This flag should be used to determine if bootstrap is invoked
from probe or reset context, reducing the rom-lock footprint of
the drivers.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Driver not able to collect minidump for ISP84xx

Issue:
minidump data collection fails as driver reports data mismatch

Fix:
When the driver encounters a new entry type that it cannot process,
it should just skip the entry and adjust the total buffer size by
subtracting the skipped bytes from it. This is to ensure that there
is no data mismatch because of the new entries.

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix processing response queue during probe

Issue:
While booting with kdump kernel, driver receive IOCB interrupts
for which it is not ready which results in processing them
before init_firmware during driver probe

Fix:
Two steps solution
1. Make driver ready to process the interrupt before interupts
handlers is registered.
2. Stop driver processing iocb interrupts if not generated as per
firmware protocol i.e R2H bit set

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Correctly handle msleep_interruptible

If waiting for signals was interrupted then the device was put to
FAILED state. Use msleep instead of msleep_interruptible to handle
this correctly.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Use IDC_CTRL bit1 directly instead of AF_83XX_NO_FWDUMP flag.

Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1
while taking minidump, to check for graceful reset.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: ISP8xxx: Correct retry of adapter initialization

Issue:

For ISP8xxx, adapter initialization is not retried if
qla4xxx_initialize_adapter fails.

Fix:

If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not
attached in order to skip retrial, then free the IRQs and then retry
initializing the adapter.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Return error if minidump data collection fails

Return error from function qla4_8xxx_collect_md_data()
if minidump data collection fails.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix the minidump data collection check in for loop

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add pex-dma support for capturing minidump

Add pex-dma support for ISP8324 and ISP8042 to improve
the minidump capture time.

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update Copyright header

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added support for ISP8042

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add flash node mgmt support

This patch allows iscsiadm to manage iSCSI target information stored on
qla4xxx adapter flash on per host basis.

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Assign correct CHAP table address to FLT

Issue:
If flash read for FLT fails, we are assigning wrong default
address for CHAP table in FLT, which will cause CHAP table
read/write to wrong address.

Fix:
Assign correct default CHAP table address to FLT.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

treewide: Fix typos in printk and comment

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

[SCSI] qla4xxx: Re-register IRQ handler while retrying initialize of adapter

Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.

Solution:
Re-register the interrupt handler when adapter initialization is retried.

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Correct the validation to check in get_sys_info mailbox

Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix MBOX intr switching from polling to intr mode for ISP83XX

Issue:
Mailbox command timed out after switching from polling mode to interrupt mode.

Events:-
1. Mailbox interrupts are disabled
2. FW generates AEN and at same time driver enables Mailbox Interrupt
3. Driver issues new mailbox to Firmware

In above case driver will not get AEN interrupts generated by FW in step #2 as
FW generated this AEN when interrupts are disabled. During the same time
driver enabled the mailbox interrupt, so driver will not poll for interrupt.
Driver will never process AENs generated in step #2 and issues new mailbox to
FW, but now FW is not able to post mailbox completion as AENs generated before
are not processed by driver.

Fix:
Enable Mailbox / AEN interrupts before initializing FW in case of ISP83XX.
This will make sure we process all Mailbox and AENs in interrupt mode.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update idc reg in case of PCI AER

Camram is reset by FW to default values after reboot/cold boot/pci reset.
In case of AER, PCI may need to reset so we need to set correct idc reg value
after PCIE error.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Print correct IDC version

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update Copyright header

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added support for ISP83XX

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added new function qla4_8xxx_get_minidump

Move minidump code from qla4_8xxx_device_bootstrap() to
new function qla4_8xxx_get_minidump() to make code more
modular.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Set IDC version in correct way

Issue:
Device can go to READY state from COLD and skip INITIALIZATION,
In this case driver will never set IDC version from function
qla4_8xxx_device_bootstrap().

Fix:
1. Set IDC version at start of function qla4_82xx_need_reset_handler().
2. Set IDC version only if we are 1st driver to load.
3. Added new function qla4_8xxx_update_idc_reg() to set all idc reg at one
place.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added new functions in isp_ops

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Clean-up and optimize macros

Remove following unused define:-

QLA82XX_MINIDUMP_OCM0_SIZE
QLA82XX_MINIDUMP_L1C_SIZE
QLA82XX_MINIDUMP_L2C_SIZE
QLA82XX_MINIDUMP_COMMON_STR_SIZE
QLA82XX_MINIDUMP_FCOE_STR_SIZE
QLA82XX_MINIDUMP_MEM_SIZE
QLA82XX_MAX_ENTRY_HDR

Added following new define to optimize code:-

MIU_TA_CTL_WRITE_ENABLE
MIU_TA_CTL_WRITE_START
MIU_TA_CTL_START_ENABLE

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Rename 82XX macros

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update func name from ql4_ to qla4_

ql4_8xxx_mark_entry_skipped to qla4_8xxx_mark_entry_skipped
ql4_attr_is_visible to qla4_attr_is_visible

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update structure and variable names

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update function name from 8xxx to 82xx

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix gcc warning for x86 system

Fix warning:-
drivers/scsi/qla4xxx/ql4_nx.c:1867:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘uint32_t’ [-Wformat]

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Use PCI Express Capability accessors

Use PCI Express Capability access functions to simplify qla4xxx driver.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP

The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure

Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

asm-generic: architecture independent readq/writeq for 32bit environment

This provides unified readq()/writeq() helper functions for 32-bit
drivers.

For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.

- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address

- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order

This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0affd5 ("x86:
remove 32-bit versions of readq()/writeq()")

The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:

#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */

But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access

This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.

Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[SCSI] qla4xxx: Remove un-necessary print statment

On ROM lock acquiring timeout failure, driver spews lot of warning
messages in a for loop, remove the unwanted warning message to reduce
kernel messages clutter.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Remove unused code

This code initially added for FW debugging, we don't need this
code now so taking it out.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Clear the RISC interrupt bit during FW init

This patch fix kernel panic during kdump.

Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix the IDC locking mechanism

This ensures the transition of dev_state from COLD to
INITIALIZING is within lock and atomic.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set

Fix issue where CPU lockup is seen when ql4xdontresethba is set and
driver is "stuck" in NEED_RESET state handler.

Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Do not add duplicate CHAP entry in FLASH

QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.

In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.

With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.

JIRA Key: UPSISCSI-146

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add new FLT firmware region

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added vendor specific sysfs attributes

Added board_id, fw_state, phy_port_cnt, phy_port_num,
iscsi_func_cnt, hba_model

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Boot from SAN support for open-iscsi

Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

x86: remove 32-bit versions of readq()/writeq()

The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5c7 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.

This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).

Build tested on 32- and 64-bit x86 allmodconfig.

Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[SCSI] qla4xxx: Updated the reset sequence for ISP82xx

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>

[SCSI] qla4xxx: Use polling mode for disable interrupt mailbox completion

Disable Interrupt MBX completion will disable the interrupt on
successful completion. Fixed the bug where driver was waiting for
Interrupt to come in for its completion. Now driver will poll for
disable interrupt MBX completion.

Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Updated the Copyright header

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Fail initialization if qla4_8xxx_pci_mem_write_2M fails

Since if fw load is failing, running on incomplete fw load would
be fatal.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: memory wedge with peg_halt test in loop

Signed-off-by: Swapnil Nagle <swapnil.nagle@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: remove unwanted check for bad spd

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Clear the rom lock if the firmware died while holding it.

There is a possibility that the firmware dies while the rom
lock is held. The only way to recover from this condition is
to forcefully unlock.

Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Trivial cleanup

* cleanup function qla4xxx_recovery_timeout
- No need to wakeup dpc thread from function
qla4xxx_recovery_timeout() as we are not doing anything
in do_dpc() thread when wakeup from
qla4xxx_recovery_timeout()

* cleanup function qla4xxx_wait_for_hba_online
- Remove hard coded value from qla4xxx_wait_for_hba_online().

* cleanup function qla4xxx_start_firmware_from_flash
- display seconds

* cleanup function qla4_8xxx_load_risc
- Remove redundant code.

* cleanup function qla4xxx_get_firmware_status
- update debug statement

* cleanup function qla4_8xxx_try_start_fw
- update return status

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: fix build on PPC

We use read/write[bslq] but do not include linux/io.h. This causes
build failures on PPC. Include that file.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Stable Tree <stable@kernel.org>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

drivers/scsi/qla4xxx: fix build

gcc-4.0.2:

drivers/scsi/qla4xxx/ql4_os.c: In function 'qla4_8xxx_error_recovery':
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2377: sorry, unimplemented: called from here
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2393: sorry, unimplemented: called from here

Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[SCSI] qla4xxx: fix compilation warning

Fix following warning:

drivers/scsi/qla4xxx/ql4_nx.c: In function 'qla4_8xxx_get_flash_info':
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'mid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'mid' was declared here
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'fid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'fid' was declared here

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Added AER support for ISP82xx

Added support for PCI error handling

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Handle outstanding mbx cmds on hung f/w scenarios

Outstanding mailbox commands, have no way to recover on f/w hung, and we
timeout on waiting for mbx response. This in turn affects the recovery process
as follows:
- We might already be in dpc while waiting for mbx to complete, so recovery for
that pci function will never get invoked. Reset Timeout (10 sec) is far less
than mbx timeout (30 sec).
- Other mbx cmds will get stuck due to serial mbx access.

Solution is to identify fw-hung scenario and handle outstanding mbx commands to
have an early-exit instead of waiting for response.
Other mbx commands waiting for access will also do an early-exit if fw-hung is
still applicable.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: updated mbx_sys_info struct to sync with FW 4.6.x


Also, changed boundary checking from size of total
structure to verification that we received the amount of
data needed to cache inernally. This change will provide
compatibility with mbx_sys_info structure sizes in both
older and newer firmware versions.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla4xxx: Added support for ISP82XX

Signed-off-by: Vikas Chaudhary <Vikas Chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>