scsi: qla2xxx: Fix premature hw access after PCI error

After a recoverable PCI error has been detected and recovered, qla driver
needs to check to see if the error condition still persist and/or wait
for the OS to give the resume signal.

Sep 8 22:26:03 localhost kernel: WARNING: CPU: 9 PID: 124606 at qla_tmpl.c:440
qla27xx_fwdt_entry_t266+0x55/0x60 [qla2xxx]
Sep 8 22:26:03 localhost kernel: RIP: 0010:qla27xx_fwdt_entry_t266+0x55/0x60
[qla2xxx]
Sep 8 22:26:03 localhost kernel: Call Trace:
Sep 8 22:26:03 localhost kernel: ? qla27xx_walk_template+0xb1/0x1b0 [qla2xxx]
Sep 8 22:26:03 localhost kernel: ? qla27xx_execute_fwdt_template+0x12a/0x160
[qla2xxx]
Sep 8 22:26:03 localhost kernel: ? qla27xx_fwdump+0xa0/0x1c0 [qla2xxx]
Sep 8 22:26:03 localhost kernel: ? qla2xxx_pci_mmio_enabled+0xfb/0x120
[qla2xxx]
Sep 8 22:26:03 localhost kernel: ? report_mmio_enabled+0x44/0x80
Sep 8 22:26:03 localhost kernel: ? report_slot_reset+0x80/0x80
Sep 8 22:26:03 localhost kernel: ? pci_walk_bus+0x70/0x90
Sep 8 22:26:03 localhost kernel: ? aer_dev_correctable_show+0xc0/0xc0
Sep 8 22:26:03 localhost kernel: ? pcie_do_recovery+0x1bb/0x240
Sep 8 22:26:03 localhost kernel: ? aer_recover_work_func+0xaa/0xd0
Sep 8 22:26:03 localhost kernel: ? process_one_work+0x1a7/0x360
..
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-8041:22: detected PCI
disconnect.
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-107ff:22:
qla27xx_fwdt_entry_t262: dump ram MB failed. Area 5h start 198013h end 198013h
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-107ff:22: Unable to
capture FW dump
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-1015:22: cmd=0x0,
waited 5221 msecs
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-680d:22: mmio
enabled returning.
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-d04c:22: MBX
Command timeout for cmd 0, iocontrol=ffffffff jiffies=10140f2e5
mb[0-3]=[0xffff 0xffff 0xffff 0xffff]

Link: https://lore.kernel.org/r/20220110050218.3958-6-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix crash during driver load on big endian machines

Crash stack:
[576544.715489] Unable to handle kernel paging request for data at address 0xd00000000f970000
[576544.715497] Faulting instruction address: 0xd00000000f880f64
[576544.715503] Oops: Kernel access of bad area, sig: 11 [#1]
[576544.715506] SMP NR_CPUS=2048 NUMA pSeries
:
[576544.715703] NIP [d00000000f880f64] .qla27xx_fwdt_template_valid+0x94/0x100 [qla2xxx]
[576544.715722] LR [d00000000f7952dc] .qla24xx_load_risc_flash+0x2fc/0x590 [qla2xxx]
[576544.715726] Call Trace:
[576544.715731] [c0000004d0ffb000] [c0000006fe02c350] 0xc0000006fe02c350 (unreliable)
[576544.715750] [c0000004d0ffb080] [d00000000f7952dc] .qla24xx_load_risc_flash+0x2fc/0x590 [qla2xxx]
[576544.715770] [c0000004d0ffb170] [d00000000f7aa034] .qla81xx_load_risc+0x84/0x1a0 [qla2xxx]
[576544.715789] [c0000004d0ffb210] [d00000000f79f7c8] .qla2x00_setup_chip+0xc8/0x910 [qla2xxx]
[576544.715808] [c0000004d0ffb300] [d00000000f7a631c] .qla2x00_initialize_adapter+0x4dc/0xb00 [qla2xxx]
[576544.715826] [c0000004d0ffb3e0] [d00000000f78ce28] .qla2x00_probe_one+0xf08/0x2200 [qla2xxx]

Link: https://lore.kernel.org/r/20201202132312.19966-8-njavali@marvell.com
Fixes: f73cb695d3ec ("[SCSI] qla2xxx: Add support for ISP2071.")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: remove incorrect sparse #ifdef

The code to try to shut up sparse warnings about questionable locking
didn't shut up sparse: it made the result not parse as valid C at all,
since the end result now has a label with no statement.

The proper fix is to just always lock the hardware, the same way Bart
did in commit 8ae178760b23 ("scsi: qla2xxx: Simplify the functions for
dumping firmware"). That avoids the whole problem with having locking
that is not statically obvious.

But in the meantime, just remove the incorrect attempt at trying to
avoid a sparse warning that just made things worse.

This was exposed by commit 3e6efab865ac ("scsi: qla2xxx: Fix reset of
MPI firmware"), very similarly to how commit cbb01c2f2f63 ("scsi:
qla2xxx: Fix MPI failure AEN (8200) handling") exposed the same problem
in another place, and caused that commit 8ae178760b23.

Please don't add code to just shut up sparse without actually fixing
what sparse complains about.

Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Arun Easi <aeasi@marvell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scsi: qla2xxx: Fix reset of MPI firmware

Normally, the MPI firmware is reset when an MPI dump is collected. If an
unsaved MPI dump exists in the driver, though, an alternate mechanism is
used. This mechanism, which was not fully correct, is not recommended and
instead an MPI dump template walk is suggested to perform the MPI reset.

To allow for the MPI dump template walk, extra space is reserved in the MPI
dump buffer which gets used only when there is already an MPI dump in
place.

Link: https://lore.kernel.org/r/20200929102152.32278-5-njavali@marvell.com
Fixes: cbb01c2f2f63 ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Correct the check for sscanf() return value

Since the version string has been modified, sscanf() returns 4 instead of
6.

Link: https://lore.kernel.org/r/20200929102152.32278-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi/qla2xxx: Convert to SPDX license identifiers

All files in this driver directory contain the following notice:

See LICENSE.qla2xxx for copyright and licensing details.

LICENSE.qla2xxx can be found in Documentation/scsi/. The file contains:

- A copyright notice

This copyright notice is redundant as all files contain the same
copyright notice already

- A license notice

You may modify and redistribute the device driver code under the
GNU General Public License (a copy of which is attached hereto as
Exhibit A) published by the Free Software Foundation (version 2).

This can be replaced with the corresponding SPDX license identifier
(GPL-2.0-only) in the source files which reference this license
file.

- The full GPLv2 license text

A redundant copy of LICENSES/preferred/GPL-2.0

Remove the notices and add the SPDX license identifier GPL-2.0-only to the
source files.

Finally remove the now redundant LICENSE.qla2xxx file.

Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix endianness annotations in source files

Fix all endianness complaints reported by sparse (C=2) without affecting
the behavior of the code on little endian CPUs.

Link: https://lore.kernel.org/r/20200518211712.11395-16-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Change {RD,WRT}_REG_*() function names from upper case into lower case

This was suggested by Daniel Wagner.

Link: https://lore.kernel.org/r/20200518211712.11395-12-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use register names instead of register offsets

Make qla27xx_write_remote_reg() easier to read by using register names
instead of register offsets. The 'pahole' tool has been used to convert
register offsets into register names. See also commit cbb01c2f2f63 ("scsi:
qla2xxx: Fix MPI failure AEN (8200) handling").

Link: https://lore.kernel.org/r/20200518211712.11395-10-bvanassche@acm.org
Cc: Arun Easi <aeasi@marvell.com>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Simplify the functions for dumping firmware

Instead of passing an argument to the firmware dumping functions that tells
these functions whether or not to obtain the hardware lock, obtain that
lock before calling these functions. This patch fixes the following
recently introduced C=2 build error:

CHECK drivers/scsi/qla2xxx/qla_tmpl.c
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: Expected ; at end of statement
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: got }
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: Expected } at end of function
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: got end-of-input

Link: https://lore.kernel.org/r/20200518211712.11395-4-bvanassche@acm.org
Fixes: cbb01c2f2f63 ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling")
Cc: Arun Easi <aeasi@marvell.com>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use true, false for ha->fw_dumped

Fix the following coccicheck warning:

drivers/scsi/qla2xxx/qla_tmpl.c:1120:2-20: WARNING: Assignment of 0/1 to
bool variable

Link: https://lore.kernel.org/r/20200430121800.15323-1-yanaijie@huawei.com
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use true, false for need_mpi_reset

Fix the following coccicheck warning:

drivers/scsi/qla2xxx/qla_tmpl.c:1031:6-20: WARNING: Assignment of 0/1 to
bool variable
drivers/scsi/qla2xxx/qla_tmpl.c:1062:3-17: WARNING: Assignment of 0/1 to
bool variable

Link: https://lore.kernel.org/r/20200430121751.15232-1-yanaijie@huawei.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix MPI failure AEN (8200) handling

Today, upon an MPI failure AEN, on top of collecting an MPI dump, a regular
firmware dump is also taken and then chip reset. This is disruptive to IOs
and not required. Make the firmware dump collection, followed by chip
reset, optional (not done by default).

Firmware dump buffer and MPI dump buffer are independent of each
other with this change and each can have dump that was taken at two
different times for two different issues. The MPI dump is saved in a
separate buffer and is retrieved differently from firmware dump.

To collect full dump on MPI failure AEN, a module parameter is
introduced:
ql2xfulldump_on_mpifail (default: 0)

Link: https://lore.kernel.org/r/20200331104015.24868-2-njavali@marvell.com
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use endian macros to assign static fields in fwdump header

This takes care of big endian architectures.

Link: https://lore.kernel.org/r/20200212214436.25532-17-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Capture FW dump on MPI heartbeat stop event

For MPI heartbeat stop Async Event, this patch would capture MPI FW dump
and chip reset. FW will tell which function to capture FW dump for.

Link: https://lore.kernel.org/r/20190912180918.6436-13-hmadhani@marvell.com
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Check for MB timeout while capturing ISP27/28xx FW dump

Add mailbox timeout checkout for ISP 27xx/28xx during FW dump procedure.
Without the timeout check, hardware lock can be held for long period. This
patch would shorten the dump procedure if a timeout condition is
encountered.

Link: https://lore.kernel.org/r/20190912180918.6436-12-hmadhani@marvell.com
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Complain if a soft reset fails

Failure of a soft reset is a severe failure. Hence report such failures.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Complain if parsing the version string fails

This patch fixes a Coverity complaint about not checking the sscanf()
return value.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Simplification of register address used in qla_tmpl.c

Reduce stack space on each fwdt routine by eliminating local variable reg.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Correction and improvement to fwdt processing

This patch cleans up and fixes firmware dump template processing. These
changes are added to support newer features for ISP27XX/ISP28XX.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add support for multiple fwdump templates/segments

This patch adds multipe firmware dump template and segments support for
ISP27XX/28XX.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Cleanups for NVRAM/Flash read/write path

This patch does following:

- Clean up NVRAM code.
- Optimizes reading of primary/secondary flash image validation.
- Remove 0xff mask and make correct width in FLT structure.
- Use endian macros to assign static fields in fwdump header.
- Correct fdwt checksum calculation.
- Simplify ql_dump_buffer() interface usage.
- Add endianizers to 27xx firmware image validator.
- fixes compiler warnings for big endian architecture.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove FW default template

This patch removes FW default template as there will never be case where
the default template would be invoked.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add new FW dump template entry types

This patch adds new firmware dump template entries for ISP27XX firmware
dump.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix code indentation for qla27xx_fwdt_entry

This patch fixes following checkpatch ERROR

ERROR: space prohibited before that ',' (ctx:WxW)

No change is functionality due to this patch.

Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Silent erroneous message

Driver uses shadow pointer instead of Mirror pointer for firmware dump
collection. Skip those entries for Mirror pointers for Request/Response
queue from firmware dump template reading.

Following messages are printed in log messages:

qla27xx_fwdt_entry_t268: unknown buffer 4
qla27xx_fwdt_entry_t268: unknown buffer 5

This patch fixes these error messages by adding skip_entry() to not read
them from template.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add longer window for chip reset

qla2x00_reset_active only covers the window of turning the chip off. Add
check to cover turning chip on.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix Firmware dump size for Extended login and Exchange Offload

This patch adjusts and reallocates fw_dump memory for target mode
to save for extended login and exchange offload buffers into
dump captured.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Skip zero queue count entry during FW dump capture

If queue count is zero while reading FW dump template, for entry
T263/T274, skip capturing those entries during FW dump capture.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix system crash while triggering FW dump

This patch fixes system hang/crash while firmware dump is attempted with
Block MQ enabled in qla2xxx driver. Fix is to remove check in fw dump
template entries for existing request and response queues so that full
buffer size is calculated during template size calculation.

Following stack trace is seen during firmware dump capture process

[ 694.390588] qla2xxx [0000:81:00.0]-5003:11: ISP System Error - mbx1=4b1fh mbx2=10h mbx3=2ah mbx7=0h.
[ 694.402336] BUG: unable to handle kernel paging request at ffffc90008c7b000
[ 694.402372] IP: memcpy_erms+0x6/0x10
[ 694.402386] PGD 105f01a067
[ 694.402386] PUD 85f89c067
[ 694.402398] PMD 10490cb067
[ 694.402409] PTE 0
[ 694.402421]
[ 694.402437] Oops: 0002 [#1] PREEMPT SMP
[ 694.402452] Modules linked in: netconsole configfs qla2xxx scsi_transport_fc
nvme_fc nvme_fabrics bnep bluetooth rfkill xt_tcpudp unix_diag xt_multiport
ip6table_filter ip6_tables iptable_filter ip_tables x_tables af_packet
iscsi_ibft iscsi_boot_sysfs xfs libcrc32c ipmi_ssif sb_edac edac_core
x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm irqbypass igb
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel iTCO_wdt
aes_x86_64 crypto_simd ptp iTCO_vendor_support glue_helper cryptd lpc_ich joydev
i2c_i801 pcspkr ioatdma mei_me pps_core tpm_tis mei mfd_core acpi_power_meter
tpm_tis_core ipmi_si ipmi_devintf tpm ipmi_msghandler shpchp wmi dca button
acpi_pad btrfs xor uas usb_storage hid_generic usbhid raid6_pq crc32c_intel ast
i2c_algo_bit drm_kms_helper syscopyarea sysfillrect
[ 694.402692] sysimgblt fb_sys_fops xhci_pci ttm ehci_pci sr_mod xhci_hcd
cdrom ehci_hcd drm usbcore sg
[ 694.402730] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-1-default+ #19
[ 694.402753] Hardware name: Supermicro X10DRi/X10DRi, BIOS 1.1a 10/16/2015
[ 694.402776] task: ffffffff81c0e4c0 task.stack: ffffffff81c00000
[ 694.402798] RIP: 0010:memcpy_erms+0x6/0x10
[ 694.402813] RSP: 0018:ffff88085fc03cd0 EFLAGS: 00210006
[ 694.402832] RAX: ffffc90008c7ae0c RBX: 0000000000000004 RCX: 000000000001fe0c
[ 694.402856] RDX: 0000000000020000 RSI: ffff8810332c01f4 RDI: ffffc90008c7b000
[ 694.402879] RBP: ffff88085fc03d18 R08: 0000000000020000 R09: 0000000000279e0a
[ 694.402903] R10: 0000000000000000 R11: f000000000000000 R12: ffff88085fc03d80
[ 694.402927] R13: ffffc90008a01000 R14: ffffc90008a056d4 R15: ffff881052ef17e0
[ 694.402951] FS: 0000000000000000(0000) GS:ffff88085fc00000(0000) knlGS:0000000000000000
[ 694.402977] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 694.403012] CR2: ffffc90008c7b000 CR3: 0000000001c09000 CR4: 00000000001406f0
[ 694.403036] Call Trace:
[ 694.403047] <IRQ>
[ 694.403072] ? qla27xx_fwdt_entry_t263+0x18e/0x380 [qla2xxx]
[ 694.403099] qla27xx_walk_template+0x9d/0x1a0 [qla2xxx]
[ 694.403124] qla27xx_fwdump+0x1f3/0x272 [qla2xxx]
[ 694.403149] qla2x00_async_event+0xb08/0x1a50 [qla2xxx]
[ 694.403169] ? enqueue_task_fair+0xa2/0x9d0

Signed-off-by: Mike Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Retain loop test for fwdump length exceeding buffer length

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Modify T262 FW dump template to specify same start/end to debug customer issues

Firmware dump allows for debugging customer issues. This patch fixes
start/end pointer calculation to capture T262 template entry for dump
tool.

Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Include ATIO queue in firmware dump when in target mode

Include ATIO queue for ISP27XX when firmware dump is collected
for target mode.

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>

qla2xxx: Add ram area DDR for fwdump template entry T262.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Fix stale pointer access.

[ Upstream Commit 84e32a06f4f8756ce9ec3c8dc7e97896575f0771 ]

Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
*rsp->in_ptr = 0;

Add additional check to make sure the pointer is valid. following
call stack will be seen

---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>] [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8 EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Avoid that sparse complains about context imbalances

Surround conditional locking statements with "#ifndef __CHECKER__" /
"#endif" to hide these for the sparse static source code analysis
tool.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: Fix sparse annotations

This patch removes 21 casts between an __iomem pointer type and
another data type but also introduces five new casts (see also
the casts with "__force"). Although this patch does not change
any functionality, IMHO the code with __force casts needs further
review.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: Remove set-but-not-used variables

Detected these variables by building with W=1.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: Prevent multiple firmware dump collection for ISP27XX.

For ISP27XX, driver will capture new firmware dump even if there is
one already collected. Prevent this from happening by checking
fw_dumped flag.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: Add udev notification to save fw dump for ISP27XX

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: Add message for sucessful FW dump collected for ISP27XX.

o Added message indicating firmware dump was sucessfully collected
for ISP27XX.
o Improve logging to help debug firmware dump process for ISP27XX.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: Fix crash due to wrong casting of reg for ISP27XX.

[Bart: additional sparse warning caused by this patch]
[jejb: fix sparse warning]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

qla2xxx: ISP27xx fwdump template error print simplification.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Add ISP27xx fwdump template entry T275 (insert buffer).

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: ISP27xx fwdump template fix insertbuf() routine.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: ISP27xx fwdump template remove high frequency debug logs.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: ISP27xx optimize fwdump entry table lookup.

Since the entry call array is sorted in order of entry type opcode,
the search can be terminated as soon as the search key is exceeded.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: ISP27xx add tests for incomplete template.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: ISP27xx queue index shadow registers.

For ISP27xx use the request/response queue index shadow registers
to avoid directly access them on the PCI bus.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: ISP27xx firmware dump template spec updates (including T274).

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Change copyright year to 2014 in all the source files.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Update entry type 270 to match spec update.

Increment the address by 4 on each iteration.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Introduce fw_dump_flag to track fw dump progress.

Signed-off-by: Hiral Patel <hiral.patel@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Correction to ISP27xx template entry types 256 and 258.

The window address inserted into the dump should be have been
incremented by 1 rather than 4.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Correct operations for ISP27xx template types 270 and 271.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

[SCSI] qla2xxx: Add support for ISP2071.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>