scsi: qla2xxx: Fix N2N stuck connection

Disk failed to rediscover after chip reset error injection. The chip reset
happens at the time when a PLOGI is being sent. This causes a flag to be
left on which blocks the retry. Clear the blocking flag.

Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add Unsolicited LS Request and Response Support for NVMe

Introduce infrastructure in the driver to support the processing of
unsolicited LS (Link Service) requests. This will involve the utilization
of a new pass-up of unsolicited FC-NVMe request IOCB interface. Unsolicited
requests will be submitted to the NVMe transport layer through
nvme_fc_rcv_ls_req(). Any received LS responses, which are sent using
xmt_ls_rsp(), will be forwarded to the firmware through the existing
Pass-Through IOCB interface, responsible for sending FC-NVMe Link Service
requests and responses.

Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove unused declarations

These declarations are not used anymore, remove them.

Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230816130842.16684-1-yuehaibing@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Adjust IOCB resource on qpair create

During NVMe queue creation, a new qpair is created. FW resource limit needs
to be re-adjusted to take into account the new qpair. Otherwise, NVMe
command can not go through. This issue was discovered while
testing/forcing FW execution to fail at load time.

Add call to readjust IOCB and exchange limit.

In addition, get FW state command and require FW to be running. Otherwise,
error is generated.

Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Multi-que support for TMF

Add queue flush for task management command, before
placing it on the wire.
Do IO flush for all Request Q's.

Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304271702.GpIL391S-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com <mailto:himanshu.madhani@oracle.com>>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Declare SCSI host template const

Make it explicit that the SCSI host template is not modified.

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230322195515.1267197-68-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add option to disable FC2 Target support

Commit 44c57f205876 ("scsi: qla2xxx: Changes to support FCP2 Target") added
support for FC2 Targets. Unfortunately, there are older setups which break
with this new feature enabled.

Allow to disable it via module option.

Link: https://lore.kernel.org/r/20230208152014.109214-1-dwagner@suse.de
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Reduce memory usage during low I/O

For edif, each I/O requires a secondary buffer to carry the FCP
cmnd. During high traffic time, these buffers are cached in the qpair. As
traffic dies down, these buffers will be trimmed as needed. If traffic is
reduced to none over 2 consecutive intervals, then these buffers will be
further trimmed.

Free FCP cmnd buffers to reduce memory usage during slow I/O time.

Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Fix performance dip due to lock contention

User experienced performance dip on measuring IOPS while EDIF
enabled. During I/O time, driver uses dma_pool_zalloc() call to allocate a
chunk of memory. This call contains a lock behind the scene which
contribute to lock contention. Save the allocated memory for reuse and
avoid the lock.

Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Relocate/rename vp map

There is no functional change in this patch. VP map resource is renamed
and relocated so it is not viewed as just a target mode resource.

Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove dead code (GNN ID)

Remove stale/unused code (GNN ID).

Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove dead code (GPNID)

Remove stale unused code for GPNID.

Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove unused declarations for qla2xxx

qla2x00_get_fw_version_str() has been removed since commit abbd8870b9cb
("[SCSI] qla2xxx: Factor-out ISP specific functions to method-based call
tables.").

qla2x00_release_nvram_protection() has been removed since commit
459c537807bd ("[SCSI] qla2xxx: Add ISP24xx flash-manipulation routines.").

qla82xx_rdmem() and qla82xx_wrmem() have been removed since commit
3711333dfbee ("[SCSI] qla2xxx: Updates for ISP82xx.").

qla25xx_rd_req_reg(), qla24xx_rd_req_reg(), qla25xx_wrt_rsp_reg(),
qla24xx_wrt_rsp_reg(), qla25xx_wrt_req_reg() and qla24xx_wrt_req_reg() have
been removed since commit 08029990b25b ("[SCSI] qla2xxx: Refactor
request/response-queue register handling.").

qla2x00_async_login_done() has been removed since commit 726b85487067
("qla2xxx: Add framework for async fabric discovery").

qlt_24xx_process_response_error() has been removed since commit
c5419e2618b9 ("scsi: qla2xxx: Combine Active command arrays.").

Remove the declarations for them from header file.

Link: https://lore.kernel.org/r/20220913023722.547249-2-cuigaosheng1@huawei.com
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Enhance driver tracing with separate tunable and more

Older tracing of driver messages was to:

- log only debug messages to kernel main trace buffer; and

- log only if extended logging bits corresponding to this message is
off

This has been modified and extended as follows:

- Tracing is now controlled via ql2xextended_error_logging_ktrace
module parameter. Bit usages same as ql2xextended_error_logging.

- Tracing uses "qla2xxx" trace instance, unless instance creation have
issues.

- Tracing is enabled (compile time tunable).

- All driver messages, include debug and log messages are now traced in
kernel trace buffer.

Trace messages can be viewed by looking at the qla2xxx instance at:

/sys/kernel/tracing/instances/qla2xxx/trace

Trace tunable that takes the same bit mask as ql2xextended_error_logging
is:

ql2xextended_error_logging_ktrace (default=1)

Link: https://lore.kernel.org/r/20220826102559.17474-6-njavali@marvell.com
Suggested-by: Daniel Wagner <dwagner@suse.de>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Revert "scsi: qla2xxx: Fix response queue handler reading stale packets"

Reverting this commit so that a fixed up patch, without adding new module
parameters, can be submitted.

Link: https://lore.kernel.org/stable/166039743723771@kroah.com/

This reverts commit b1f707146923335849fb70237eec27d4d1ae7d62.

Link: https://lore.kernel.org/r/20220826102559.17474-2-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix discovery issues in FC-AL topology

A direct attach tape device, when gets swapped with another, was not
discovered. Fix this by looking at loop map and reinitialize link if there
are devices present.

Link: https://lore.kernel.org/linux-scsi/baef87c3-5dad-3b47-44c1-6914bfc90108@cybernetics.com/
Link: https://lore.kernel.org/r/20220713052045.10683-8-njavali@marvell.com
Cc: stable@vger.kernel.org
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix response queue handler reading stale packets

On some platforms, the current logic of relying on finding new packet
solely based on signature pattern can lead to driver reading stale
packets. Though this is a bug in those platforms, reduce such exposures by
limiting reading packets until the IN pointer.

Two module parameters are introduced:

ql2xrspq_follow_inptr:

When set, on newer adapters that has queue pointer shadowing, look for
response packets only until response queue in pointer.

When reset, response packets are read based on a signature pattern
logic (old way).

ql2xrspq_follow_inptr_legacy:

Like ql2xrspq_follow_inptr, but for those adapters where there is no
queue pointer shadowing.

Link: https://lore.kernel.org/r/20220713052045.10683-5-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add a new v2 dport diagnostic feature

FW requires minimum 72 bytes buffer size for D_port result. Buffer size
1024 is mentioned in the FW spec so buffer size is increased to 1024.
Rewrite the logic to handle START/RESTART command from SDMAPI.

Link: https://lore.kernel.org/r/20220616053508.27186-3-njavali@marvell.com
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Remove old doorbell interface

Recently driver has implemented a new doorbell mechanism via bsg. The new
doorbell tells driver the exact buffer size application has where driver
can fill it up with events. The old doorbell guestimated application buffer
size is 256.

Remove duplicate functionality, the application has moved on to the new
doorbell interface.

Link: https://lore.kernel.org/r/20220607044627.19563-9-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Reduce Initiator-Initiator thrashing

This patch uses GFFID switch command to scan whether remote device is
Target or Initiator mode. Based on that info, driver will not pass up
Initiator info to authentication application. This helps reduce unnecessary
stress for authentication application to deal with unused connections.

Link: https://lore.kernel.org/r/20220607044627.19563-2-njavali@marvell.com
Fixes: 7ebb336e45ef ("scsi: qla2xxx: edif: Add start + stop bsgs")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use named initializers for q_dev_state

Make q_dev_state a little more readable and maintainable by using named
initializers.

Also convert QLA8XXX_DEV_* macros into an enum and remove
qla83xx_dev_state_to_string(), which is a duplicate of qdev_state().

Link: https://lore.kernel.org/r/AS8PR10MB495298515A7553C8D6D6E74D9D349@AS8PR10MB4952.EURPRD10.PROD.OUTLOOK.COM
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Gleb Chesnokov <Chesnokov.G@raidix.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ql2xnvme_queues module param to configure number of NVMe queues

Add ql2xnvme_queues module parameter to configure number of NVMe queues

Usage:

Number of NVMe Queues that can be configured.

Final value will be min(ql2xnvme_queues, num_cpus, num_chip_queues),

1 - Minimum number of queues supported
8 - Default value
128 - Maximum number of queues supported

Link: https://lore.kernel.org/r/20220110050218.3958-10-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shreyas Deodhar <sdeodhar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Implement ref count for SRB

The timeout handler and the done function are racing. When
qla2x00_async_iocb_timeout() starts to run it can be preempted by the
normal response path (via the firmware?). qla24xx_async_gpsc_sp_done()
releases the SRB unconditionally. When scheduling back to
qla2x00_async_iocb_timeout() qla24xx_async_abort_cmd() will access an freed
sp->qpair pointer:

qla2xxx [0000:83:00.0]-2871:0: Async-gpsc timeout - hdl=63d portid=234500 50:06:0e:80:08:77:b6:21.
qla2xxx [0000:83:00.0]-2853:0: Async done-gpsc res 0, WWPN 50:06:0e:80:08:77:b6:21
qla2xxx [0000:83:00.0]-2854:0: Async-gpsc OUT WWPN 20:45:00:27:f8:75:33:00 speeds=2c00 speed=0400.
qla2xxx [0000:83:00.0]-28d8:0: qla24xx_handle_gpsc_event 50:06:0e:80:08:77:b6:21 DS 7 LS 6 rc 0 login 1|1 rscn 1|0 lid 5
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: qla24xx_async_abort_cmd+0x1b/0x1c0 [qla2xxx]

Obvious solution to this is to introduce a reference counter. One reference
is taken for the normal code path (the 'good' case) and one for the timeout
path. As we always race between the normal good case and the timeout/abort
handler we need to serialize it. Also we cannot assume any order between
the handlers. Since this is slow path we can use proper synchronization via
locks.

When we are able to cancel a timer (del_timer returns 1) we know there
can't be any error handling in progress because the timeout handler hasn't
expired yet, thus we can safely decrement the refcounter by one.

If we are not able to cancel the timer, we know an abort handler is
running. We have to make sure we call sp->done() in the abort handlers
before calling kref_put().

Link: https://lore.kernel.org/r/20220110050218.3958-3-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Refactor asynchronous command initialization

Move common open-coded asynchronous command initializing code such as
setting up the timer and the done callback into one function. This is a
preparation step and allows us later on to change the low level error flow
handling at a central place.

Link: https://lore.kernel.org/r/20220110050218.3958-2-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Flush stale events and msgs on session down

On session down, driver will flush all stale messages and doorbell
events. This prevents authentication application from having to process
stale data.

Link: https://lore.kernel.org/r/20211026115412.27691-7-njavali@marvell.com
Fixes: 4de067e5df12 ("scsi: qla2xxx: edif: Add N2N support for EDIF")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Karunakara Merugu <kmerugu@marvell.com>
Signed-off-by: Karunakara Merugu <kmerugu@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Turn off target reset during issue_lip

When user uses issue_lip to do link bounce, driver sends additional target
reset to remote device before resetting the link. The target reset would
affect other paths with active I/Os. This patch will remove the unnecessary
target reset.

Link: https://lore.kernel.org/r/20211026115412.27691-4-njavali@marvell.com
Fixes: 5854771e314e ("[SCSI] qla2xxx: Add ISPFX00 specific bus reset routine")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Switch to attribute groups

struct device supports attribute groups directly but does not support
struct device_attribute directly. Hence switch to attribute groups.
Additionally, remove qla_insert_tgt_attrs() and replace it with
qla_host_attr_is_visible().

Link: https://lore.kernel.org/r/20211012233558.4066756-41-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove a declaration

Since there is no definition for the qla2x00_host_attrs_dm array, remove
its declaration.

Link: https://lore.kernel.org/r/20211012233558.4066756-40-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add support for mailbox passthru

This interface will allow user space applications to send a mailbox command
to the firmware.

Link: https://lore.kernel.org/r/20210908164622.19240-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add N2N support for EDIF

For EDIF + N2N to work, firmware 9.8 or later is required. The driver will
pause after PLOGI to allow app to authenticate. Once authentication
completes, app will tell driver to do PRLI.

Link: https://lore.kernel.org/r/20210817051315.2477-6-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add encryption to I/O path

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

After the completion of PLOGI, both sides have authenticated and PRLI
completed, encrypted I/Os are allowed to proceed.

- Use new firmware API to encrypt traffic on the wire

- Add driver parameter to enable|disable EDIF feature

# modprobe qla2xxx ql2xsecenable=1

Link: https://lore.kernel.org/r/20210624052606.21613-10-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add doorbell notification for app

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

During runtime, driver and authentication application need to stay in sync
in terms of: Session being down|up, arrival of new authentication
message (AUTH ELS) and SADB update completion.

These events are queued up as doorbell to the authentication
application. Application would read this doorbell on regular basis to stay
up to date. Each SCSI host would have a separate doorbell queue.

The doorbell interface can daisy chain a list of events for each read. Each
event contains an event code + hint to help application steer the next
course of action.

Link: https://lore.kernel.org/r/20210624052606.21613-9-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add detection of secure device

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

There is no FC switch scan service that can indicate whether a device is
secure or non-secure.

In order to detect whether the remote port supports encrypted operation,
driver must first do a PLOGI with the remote device. On completion of the
PLOGI, driver will query firmware to see if the device supports secure
login. To do that, driver + firmware must advertise the security bit via
PLOGI's service parameter. The remote device shall respond using the same
service parameter whether it supports it or not.

Link: https://lore.kernel.org/r/20210624052606.21613-8-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add authentication pass + fail bsgs

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

On completion of the authentication process, the authentication application
will notify driver on whether it is successful or not.

In case of success, application will use the QL_VND_SC_AUTH_OK BSG call to
tell driver to proceed to the PRLI phase.

In case of failure, application will use the QL_VND_SC_AUTH_FAIL bsg call
to tell driver to tear down the connection and retry. In the case where an
existing session is active, the re-key process can fail. The session tear
down ensures data is not further compromised.

Link: https://lore.kernel.org/r/20210624052606.21613-7-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add key update

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

As part of the authentication process, the authentication application will
generate a SADB entry (Security Association/SA, key, SPI value, etc). This
SADB is then passed to driver to be programmed into hardware. There will be
a pair of SADB's (Tx and Rx) for each connection.

After some period, the application can choose to change the key. At that
time, a new set of SADB pair is given to driver. The old set of SADB will
be deleted.

Add a new bsg call (QL_VND_SC_SA_UPDATE) to allow application to allow
adding or deleting SADB entries. Driver will not keep the key in
memory. It will pass it to HW.

It is assumed that application will assign a unique SPI value to this SADB
(SA + key). Driver + hardware will assign a handle to track this unique
SPI/SADB.

Link: https://lore.kernel.org/r/20210624052606.21613-6-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add extraction of auth_els from the wire

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

Once authentication messages sent from a remote device have arrived, each
message is extracted and placed in a buffer for application to retrieve.
The FC frame header will be stripped, leaving behind the AUTH ELS payload.
It is up to the application to strip the AUTH ELS header to get to the
actual authentication message.

Link: https://lore.kernel.org/r/20210624052606.21613-5-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add send, receive, and accept for auth_els

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

Add the ability for authentication application to send and retrieve
messages as part of the authentication process via existing
FC_BSG_HST_ELS_NOLOGIN BSG interface.

To send a message, application is expected to format the data in the AUTH
ELS format. Refer to FC-SP2 for details.

If a message was received, application is required to reply with either a
LS_ACC or LS_RJT complete the exchange using the same interface. Otherwise,
remote device will treat it as a timeout.

Link: https://lore.kernel.org/r/20210624052606.21613-4-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: edif: Add start + stop bsgs

Some FC adapters from Marvell offer the ability to encrypt data in flight
(EDIF). This feature requires an application to act as an authenticator.

Add two new BSG calls:

- QL_VND_SC_APP_START: Application will announce its presence to driver
with this call. Driver will restart all connections to see if remote
device supports security or not.

- QL_VND_SC_APP_STOP: Application announces it is in the process of
exiting. Driver will restart all connections to revert back to
non-secure. Provided the remote device is willing to allow a non-secure
connection.

Link: https://lore.kernel.org/r/20210624052606.21613-2-njavali@marvell.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Signed-off-by: Larry Wisneski <Larry.Wisneski@marvell.com>
Co-developed-by: Duane Grigsby <duane.grigsby@marvell.com>
Signed-off-by: Duane Grigsby <duane.grigsby@marvell.com>
Co-developed-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Rick Hicksted Jr <rhicksted@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add heartbeat check

Use "no-op" mailbox command to check if the adapter firmware is still
responsive.

Link: https://lore.kernel.org/r/20210619052427.6440-1-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove duplicate declarations

qla2x00_post_uevent_work(), qla2x00_free_fcport() and ql2xexlogins are
declared multiple times. Remove the duplicates.

Link: https://lore.kernel.org/r/1621843402-34828-1-git-send-email-zhangshaokun@hisilicon.com
Cc: Nilesh Javali <njavali@marvell.com>
Cc: GR-QLogic-Storage-Upstream@marvell.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix crash in PCIe error handling

BUG: unable to handle kernel NULL pointer dereference at (null)
IP: qla2x00_abort_isp+0x21/0x6b0 [qla2xxx] PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 0 PID: 1715 Comm: kworker/0:2
Tainted: GOE 4.12.14-122.37-default #1 SLE12-SP5
Hardware name: HPE Superdome Flex/Superdome Flex, BIOS
Bundle:3.30.100 SFW:IP147.007.004.017.000.2009211957 09/21/2020
Workqueue: events aer_recover_work_func
task: ffff9e399c14ca80 task.stack: ffffc1c58e4ac000
RIP: 0010:qla2x00_abort_isp+0x21/0x6b0 [qla2xxx]
RSP: 0018:ffffc1c58e4afd50 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff9e419cdef480 RCX: 0000000000000000
RDX: ffff9e399c14ca80 RSI: 0000000000000246 RDI: ffff9e419bbc27b8
RBP: ffff9e419bbc27b8 R08: 0000000000000004 R09: 00000000a0440000
R10: 0000000000000000 R11: ffff9e399416d1a0 R12: ffff9e419cdef000
R13: ffff9e3a7cfae800 R14: ffff9e3a7cfae800 R15: 00000000000000c0
FS: 0000000000000000(0000) GS:ffff9e39a0000000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000006cd00a005 CR4: 00000000007606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
qla2xxx_pci_slot_reset+0x141/0x160 [qla2xxx]
report_slot_reset+0x41/0x80
? merge_result.part.4+0x30/0x30
pci_walk_bus+0x70/0x90
pcie_do_recovery+0x1db/0x2e0
aer_recover_work_func+0xc2/0xf0
process_one_work+0x14c/0x390

Disable board_disable logic where driver resources are freed while OS is in
the process of recovering the adapter.

Link: https://lore.kernel.org/r/20210329085229.4367-9-njavali@marvell.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Wait for ABTS response on I/O timeouts for NVMe

FW needs to wait for an ABTS response before completing the I/O.

Link: https://lore.kernel.org/r/20210111093134.1206-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Implementation to get and manage host, target stats and initiator port

This statistics will help in debugging process and checking specific error
counts. It also provides a capability to isolate the port or bring it out
of isolation.

Link: https://lore.kernel.org/r/20210111093134.1206-2-njavali@marvell.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix reset of MPI firmware

Normally, the MPI firmware is reset when an MPI dump is collected. If an
unsaved MPI dump exists in the driver, though, an alternate mechanism is
used. This mechanism, which was not fully correct, is not recommended and
instead an MPI dump template walk is suggested to perform the MPI reset.

To allow for the MPI dump template walk, extra space is reserved in the MPI
dump buffer which gets used only when there is already an MPI dump in
place.

Link: https://lore.kernel.org/r/20200929102152.32278-5-njavali@marvell.com
Fixes: cbb01c2f2f63 ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add IOCB resource tracking

This patch tracks number of IOCB resources used in the I/O fast path. If
the number of used IOCBs reach a high water limit, driver would return the
I/O as busy and let upper layer retry. This prevents over subscription of
IOCB resources where any future error recovery command is unable to cut
through. Enable IOCB throttling by default.

Link: https://lore.kernel.org/r/20200904045128.23631-12-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Reduce duplicate code in reporting speed

Indicate correct speed for 16G Mezz card.

Link: https://lore.kernel.org/r/20200904045128.23631-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Setup debugfs entries for remote ports

Create a base for adding remote port related entries in debugfs.

Link: https://lore.kernel.org/r/20200904045128.23631-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi/qla2xxx: Convert to SPDX license identifiers

All files in this driver directory contain the following notice:

See LICENSE.qla2xxx for copyright and licensing details.

LICENSE.qla2xxx can be found in Documentation/scsi/. The file contains:

- A copyright notice

This copyright notice is redundant as all files contain the same
copyright notice already

- A license notice

You may modify and redistribute the device driver code under the
GNU General Public License (a copy of which is attached hereto as
Exhibit A) published by the Free Software Foundation (version 2).

This can be replaced with the corresponding SPDX license identifier
(GPL-2.0-only) in the source files which reference this license
file.

- The full GPLv2 license text

A redundant copy of LICENSES/preferred/GPL-2.0

Remove the notices and add the SPDX license identifier GPL-2.0-only to the
source files.

Finally remove the now redundant LICENSE.qla2xxx file.

Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: SAN congestion management implementation

* Firmware Initialization with SCM enabled based on NVRAM setting and
firmware support (About Firmware).

* Enable PUREX and add support for fabric performance impact
notification (FPIN) handling.

* Allocate a default PUREX item for each vha to handle memory allocation
failures in ISR.

Link: https://lore.kernel.org/r/20200630102229.29660-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Change in PUREX to handle FPIN ELS requests

SAN Congestion Management generates ELS pkts whose size can vary and be >
64 bytes. Change the PUREX handling code to support non-standard ELS pkt
size.

Link: https://lore.kernel.org/r/20200630102229.29660-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Simplify the functions for dumping firmware

Instead of passing an argument to the firmware dumping functions that tells
these functions whether or not to obtain the hardware lock, obtain that
lock before calling these functions. This patch fixes the following
recently introduced C=2 build error:

CHECK drivers/scsi/qla2xxx/qla_tmpl.c
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: Expected ; at end of statement
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: got }
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: Expected } at end of function
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: got end-of-input

Link: https://lore.kernel.org/r/20200518211712.11395-4-bvanassche@acm.org
Fixes: cbb01c2f2f63 ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling")
Cc: Arun Easi <aeasi@marvell.com>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Make qlafx00_process_aen() return void

No other functions use the return value of qlafx00_process_aen() and the
return value is always 0 now. Make it return void. This fixes the following
coccicheck warning:

drivers/scsi/qla2xxx/qla_mr.c:1716:5-9: Unneeded variable: "rval".
Return "0" on line 1768

Link: https://lore.kernel.org/r/20200506061757.19536-1-yanaijie@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix MPI failure AEN (8200) handling

Today, upon an MPI failure AEN, on top of collecting an MPI dump, a regular
firmware dump is also taken and then chip reset. This is disruptive to IOs
and not required. Make the firmware dump collection, followed by chip
reset, optional (not done by default).

Firmware dump buffer and MPI dump buffer are independent of each
other with this change and each can have dump that was taken at two
different times for two different issues. The MPI dump is saved in a
separate buffer and is retrieved differently from firmware dump.

To collect full dump on MPI failure AEN, a module parameter is
introduced:
ql2xfulldump_on_mpifail (default: 0)

Link: https://lore.kernel.org/r/20200331104015.24868-2-njavali@marvell.com
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Update BPM enablement semantics.

commit e4e3a2ce9556 ("scsi: qla2xxx: Add ability to autodetect SFP
type") takes a heavy handed approach to BPM (Buffer Plus Management)
enablement:

1) During hardware initialization, if an LR-capable transceiver is
recognized, the driver schedules a disruptive post-initialization
chip-reset (ISP-ABORT) to allow the BPM settings to be sent to the
firmware. This chip-reset will result in (short-term) path-loss to
all fc-rports and their attached SCSI devices.

2) LR-detection is triggered during any link-up event, resulting in a
refresh and potential chip-reset

Based on firmware-team guidance, upon LR-capable transceiver
recognition, the driver's hardware initialization code will now
re-execute firmware with the new BPM settings, then continue on with
driver initialization. To address the second issue, the driver
performs LR-capable detection upon the driver receiving a
transceiver-insertion asynchronous event from firmware. No short-term
path loss is needed with this new semantic.

Link: https://lore.kernel.org/r/20200226224022.24518-10-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs

There's no point checking flags.disable_msix_handshake in the
interrupt handler hot-path. Instead perform the check during
queue-pair instantiation and use the proper interrupt handler.

Link: https://lore.kernel.org/r/20200226224022.24518-8-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use FC generic update firmware options routine for ISP27xx

This patch uses generic firmware update options for FCoE based
adapters as well to reduce code duplication.

Link: https://lore.kernel.org/r/20200226224022.24518-4-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add deferred queue for processing ABTS and RDP

This patch adds deferred queue for processing aborts and RDP in the driver.

Link: https://lore.kernel.org/r/20200212214436.25532-14-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ql2xrdpenable module parameter for RDP

This patch provides separate module parameter ql2xrdpenable to turn on/off
RDP capability in the driver. However, if ql2xsmartsan parameter is
enabled, it will also turn on ql2xfdmienable parameter since it is required
for RDP to work.

Link: https://lore.kernel.org/r/20200212214436.25532-9-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add vendor extended RDP additions and amendments

This patch adds RDP command support in the driver. With the help of new
ql2xsmartsan parameter, driver will use PUREX IOCB mode to send RDP command
to switch and will be able to receive various diagnostic data.

Link: https://lore.kernel.org/r/20200212214436.25532-8-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add changes in preparation for vendor extended FDMI/RDP

This patch prepares code for implementing Vendor specific extended FDMI/RDP
commands. It also addes support for MBC_GET_PORT_DATABASE and
MBC_GET_RNID_PARAMS commands.

Link: https://lore.kernel.org/r/20200212214436.25532-7-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add beacon LED config sysfs interface

This patch provides an interface to do the following (using MBC 0x3B):

- Displays (in hex) the LED config words for all three LEDs.

- Programs the config words for one LED or for all three LEDs.

The sysfs node defined is named beacon_config.

First, to allow driver to gain LED control, do this:
# echo 1 > /sys/class/scsi_host/host#/beacon

Then, to display config words for all three LEDs do this:
# cat /sys/class/scsi_host/host#/beacon_config

To set config words for all three LEDs do this:
# echo 3 xxxx yyyy zzzz > /sys/class/scsi_host/host#/beacon_config

Or, to set config word for a specific single LED n do this:
# echo n xxxx > /sys/class/scsi_host/host#/beacon_config
where n is the LED number (0, 1, 2)

Finally, to restore LED control back to firmware, do this:
# echo 0 > /sys/class/scsi_host/host#/beacon

Link: https://lore.kernel.org/r/20200212214436.25532-2-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use common routine to free fcport struct

This patch does not change any any functionality.

Link: https://lore.kernel.org/r/20191217220617.28084-8-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Cleanup unused async_logout_done

This patch removes unused qla2x00_async_logout_done from the code.

Link: https://lore.kernel.org/r/20191217220617.28084-5-hmadhani@marvell.com
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add a shadow variable to hold disc_state history of fcport

This patch adds a shadow variable to hold disc_state history for the fcport
and prints state transition when the logging is enabled.

Link: https://lore.kernel.org/r/20191217220617.28084-4-hmadhani@marvell.com
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix fabric scan hang

On timeout, SRB pointer was cleared from outstanding command array and
dropped. It was not allowed to go through the done process and cleanup.
This patch will abort the SRB where FW will return it with an error status
and resume the normal cleanup.

Link: https://lore.kernel.org/r/20191217220617.28084-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove defer flag to indicate immeadiate port loss

During cable pull test case, if the port is disconnected for time larger
than devloss timeout, driver does not mark path offline. In such case,
instead of notifying SCSI-ML of loop down, driver goes into endless loop of
device relogin because defer flag is set.

With newer handling of device relogin in driver discovery, defer flag is
now redundant. This patch removes defer flag and cleans up code handling
port lost indication to SCSI-ML.

Link: https://lore.kernel.org/r/20191217220617.28084-2-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix device connect issues in P2P configuration

P2P needs to take the alternate plogi route.

Link: https://lore.kernel.org/r/20191105150657.8092-8-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Introduce qla2x00_els_dcmd2_free()

This patch reduces code duplication.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Inline the qla2x00_fcport_event_handler() function

Instead of calling qla2x00_fcport_event_handler() and letting the switch
statement inside that function decide which other function to call, call
the latter function directly. Remove the event member from the event_arg
structure because it is no longer needed. Remove the
qla_handle_els_plogi_done() function because it is never called.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Introduce qla2xxx_get_next_handle()

This patch reduces code duplication.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Enable type checking for the SRB free and done callback functions

Since all pointers passed to the srb_t.done() and srb_t.free() functions
have type srb_t, change the type of the first argument of these functions
from void * into struct srb *. This allows the compiler to verify the
argument types for these functions. This patch does not change any
functionality.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Change the return type of qla24xx_read_flash_data()

This change makes it easier to detect qla24xx_read_flash_data() failures
and also to handle such failures. This change does not modify the behavior
of the driver since all callers ignore the qla24xx_read_flash_data()
return value.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Check the PCI info string output buffer size

Pass the output buffer size to the code that generates a PCI info string
and check the output buffer size while generating a PCI info string.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Declare fourth qla2x00_set_model_info() argument const

Make it clear to humans and also to the compiler that the string passed
as fourth argument is not modified.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Declare the fourth ql_dump_buffer() argument const

This patch makes it clear to humans and also to the compiler that
ql_dump_buffer() does not modify the memory the @buf argument points at.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: move IO flush to the front of NVME rport unregistration

On session deletion, current qla code would unregister an NVMe session
before flushing IOs. This patch would move the unregistration of NVMe
session after IO flush. This way FC-NVMe layer would not have to wait for
stuck IOs. In addition, qla2xxx would stop accepting new IOs during session
deletion.

Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures

Introduce two structures for the (DMA address, length) combination instead
of using separate structure members for the DMA address and length. This
patch fixes several Coverity complaints about 'cur_dsd' being used to write
outside the bounds of structure members.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Make qla24xx_async_abort_cmd() static

Since qla24xx_async_abort_cmd() is only called from inside qla_init.c,
declare that function static. Reorder a few functions to avoid that any
forward declarations are needed.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Uninline qla2x00_init_timer()

Since qla2x00_init_timer() is not used for I/O commands there is no need to
inline this function. Hence uninline this function.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move qla2x00_clear_loop_id() from qla_inline.h into qla_init.c

Since qla2x00_clear_loop_id() is not in the hot path, uninline it.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Declare qla2x00_find_new_loop_id() static

Since all qla2x00_find_new_loop_id() calls occur in the same source file as
the definition of this function, move that function to just before its
first caller and declare it static. Convert the header above this function
into kernel-doc format.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move qla2x00_set_fcport_state() from a .h into a .c file

The qla2x00_set_fcport_state() function is not in the hot path so move its
definition from a .h into a .c file.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Declare qla24xx_build_scsi_crc_2_iocbs() static

Since qla24xx_build_scsi_crc_2_iocbs() is only used inside a single source
file, declare this function static.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix formatting of pointer types

Improve source code readability by following the Linux kernel coding style
for pointer types. This patch only changes whitespace.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Secure flash update support for ISP28XX

This patch adds support for Secure flash update with ISP28xx.

Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add 28xx flash primary/secondary status/image mechanism

Includes the following:
- correction to 27xx image status struct;
- factoring of 27xx image status validating routines to make common;
- image status generation compare that works across zero wrap;
- bsg interface to report current active images (as loaded by driver).

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Update flash read/write routine

This patch makes following changes to flash access routines:

- update return type for read_optrom
- use void instead of uint32_t * for buffer parameter in read
and write optrom routines
- fix flash/nvram addressing

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add support for multiple fwdump templates/segments

This patch adds multipe firmware dump template and segments support for
ISP27XX/28XX.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Cleanups for NVRAM/Flash read/write path

This patch does following:

- Clean up NVRAM code.
- Optimizes reading of primary/secondary flash image validation.
- Remove 0xff mask and make correct width in FLT structure.
- Use endian macros to assign static fields in fwdump header.
- Correct fdwt checksum calculation.
- Simplify ql_dump_buffer() interface usage.
- Add endianizers to 27xx firmware image validator.
- fixes compiler warnings for big endian architecture.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove FW default template

This patch removes FW default template as there will never be case where
the default template would be invoked.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move marker request behind QPair

Current code hard codes marker request to use request and response queue
0. This patch make use of the qpair as the path to access the
request/response queues. It allows marker to be place on any hardware
queue.

Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add support for setting port speed

This patch adds sysfs node

1. There is a new sysfs node port_speed
2. The possible values are 2(Auto neg), 8, 16, 32
3. A value outside of the above defaults to Auto neg
4. Any update to the setting causes a link toggle
5. This feature is currently only for ISP27xx

Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix DMA error when the DIF sg buffer crosses 4GB boundary

When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.

Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add mode control for each physical port

Add ability to allow each physical port to control operating mode. Current
code forces all ports to behave in one mode (i.e. initiator, target or
dual). This patch allows user to select the operating mode for each port.

- Driver must be loaded in dual mode to allow resource allocation

modprobe qla2xxx qlini_mode=dual

- In addition user can make adjustment to exchange resources using following
command

echo 1024 > /sys/class/scsi_host/host<x>/ql2xiniexchg
echo 1024 > /sys/class/scsi_host/host<x>/ql2xexchoffld

- trigger mode change and new setting of ql2xexchoffld|ql2xiniexchg

echo [<value>] > /sys/class/scsi_host/host<x>/qlini_mode

where, value can be one of following
- enabled
- disabled
- dual
- exclusive

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove stale ADISC_DONE event

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove ASYNC GIDPN switch command

Using GPNFT/GNNFT command will be able to cover switch database with less
number of scans. This patch removes Get NportID with provided WWPN/GIDPN
switch command. By making this change, in large fabric with lots of remote
port or NPIV ports with noisy SAN, the number of GIDPN commands issued by a
port when it detects large number of remote ports going away or coming back,
can overwhelmn the switch and it can becomde unresponsive. In a case where the
fabric has not change, GIDPN is not required.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move rport registration out of internal work_list

Currently, the rport registration is being called from a single work element
that is used to process QLA internal "work_list". This work_list is meant for
quick and simple task (ie no sleep). The Rport registration process sometime
can be delayed by upper layer. This causes back pressure with the internal
queue where other jobs are unable to move forward.

This patch will schedule the registration process with a new work element
(fc_port.reg_work). While the RPort is being registered, the current state of
the fcport will not move forward until the registration is done. If the state
of the fabric has changed, a new field/next_disc_state will record the next
action on whether to 'DELETE' or 'Reverify the session/ADISC'.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Migrate NVME N2N handling into state machine

This patch fixes regression introduced for the N2N support for FC-NVMe. For
FC-NVMe with N2N connection, instead of FW initiating the Login, Driver
starts Login process. This patch migrates that new process from a
standalone path into existing session management state machine. With this
state change now driver will not wait for pull NPort ID from FW.

Fixes: edd05de197592 ("scsi: qla2xxx: Changes to support N2N logins")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix race between switch cmd completion and timeout

Fix race condition between switch cmd completion and timeout timer. Timer
has popped triggers command free. On IOCB completion, stale sp point was
reused. Instead, an abort will be sent to FW to nudge the command out of FW
where the normal completion will take place.

RIP: 0010:qla2x00_chk_ms_status+0xf3/0x1b0 [qla2xxx]
Call Trace:
<IRQ>
qla24xx_els_ct_entry.isra.15+0x1d4/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x39/0xf0 [qla2xxx]
qla24xx_process_response_queue+0xbc/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x8a/0xf0 [qla2xxx]
__handle_irq_event_percpu+0xa0/0x1f0

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix Management Server NPort handle reservation logic

After selecting the NPort handle/loop_id, set a bit in the loop_id_map to
prevent others from selecting the same NPort handle.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix NPIV deletion by calling wait_for_sess_deletion

Add wait for session deletion to finish before freeing an NPIV scsi host.

Fixes: 726b85487067 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move GPSC and GFPNID out of session management

Move GPSC & GFPNID commands out of session management to reduce time lag
in reporting the session state to remote port. These commands are not
essential when it comes to maintaining the rport state. Delay sending
these commands after rport state is set to Online.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan

This patch combines FCP and FC-NVMe scan into single scan when
driver detects FC-NVMe capability on same port.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove nvme_done_list

Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Serialize session deletion by using work_lock

for session deletion, replace sess_lock with work_lock.
Under certain case sess_lock is not feasiable to acquire.
The lock is needed temporarily to make sure a single
call to schedule of the work element.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove unused argument from qlt_schedule_sess_for_deletion()

Immeadiate flag is not used for scheduling session deletion.
Remove it to simplfy session deletion code path.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ability to use GPNFT/GNNFT for RSCN handling

add ability to use gpnft/gnnft to handle RSCN.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Migrate switch registration commands away from mailbox interface

Migrate switch registration commands: RFTID, RFFID, RNNID and RSNN_NN
out of mailbox interface to reduce fabric scan bottle neck.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add switch command to simplify fabric discovery

- add "async" gpn_ft, gnn_ft, gfpn_id, gnn_id switch commands.
- For 8G and newer adapters, use async commands when it comes to
fabric scan to reduce bottle neck.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Tweak resource count dump

Fetch actual data from firmware instead of static data
at chip reset time.

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ability to send PRLO

Add ability to send Implicit PRLO to flush IOs
from FW back to driver.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add option for use reserve exch for ELS

Add option to tell FW to reserve 1/2 of emergency exchanges for ELS.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move work element processing out of DPC thread

DPC thread can stall during switch scan due to slow switch response.
This will stall other work element that needs attention. Moving work
element processing and relogin logic out of DPC thread and into its
own work queue.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Convert timers to use timer_setup()

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: qla2xxx-upstream@qlogic.com
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Bart Van Assche <Bart.VanAssche@wdc.com>

scsi: qla2xxx: Changes to support N2N logins

If we discovered a topology that is N2N then we will issue a login to
the target. If our WWPN is bigger than the target's WWPN then we will
initiate login, otherwise we will just wait for the target to initiate
login.

[mkp: many whitespace errors]

Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Reinstate module parameter ql2xenablemsix

[mkp: fixed whitespace]

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix slow mem alloc behind lock

Call Trace:
[<ffffffff81341687>] dump_stack+0x6b/0xa4
[<ffffffff810c3e30>] ? print_irqtrace_events+0xd0/0xe0
[<ffffffff8109e3c3>] ___might_sleep+0x183/0x240
[<ffffffff8109e4d2>] __might_sleep+0x52/0x90
[<ffffffff811fe17b>] kmem_cache_alloc_trace+0x5b/0x300
[<ffffffff810c666b>] ? __lock_acquired+0x30b/0x420
[<ffffffffa0733c28>] qla2x00_alloc_fcport+0x38/0x2a0 [qla2xxx]
[<ffffffffa07217f4>] ? qla2x00_do_work+0x34/0x2b0 [qla2xxx]
[<ffffffff816cc82b>] ? _raw_spin_lock_irqsave+0x7b/0x90
[<ffffffffa072169a>] ? qla24xx_create_new_sess+0x3a/0x160 [qla2xxx]
[<ffffffffa0721723>] qla24xx_create_new_sess+0xc3/0x160 [qla2xxx]
[<ffffffff810c91ed>] ? trace_hardirqs_on+0xd/0x10
[<ffffffffa07218f8>] qla2x00_do_work+0x138/0x2b0 [qla2xxx]

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Recheck session state after RSCN

When RSCN is delivered for specific remote port. Use ADISC to verify the
session is still valid or not.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ability to autodetect SFP type

SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add command completion for error path

The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.

Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Added change to enable ZIO for FC-NVMe devices

Add support to the driver to set the exchange threshold value for
the number of outstanding AENs.

Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move function prototype to correct header

Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Send FC4 type NVMe to the management server

This patch adds switch command support for FC-4 type of FC-NVMe (0x28)
for resgistering HBA port to the management server. RFT_ID command is
used to register FC-4 type of 0x28 and RFF_ID is used to register FC-4
features bits for FC-NVMe port.

Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-By: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add FC-NVMe F/W initialization and transport registration

This code provides the interfaces to register remote and local ports of
FC4 type 0x28 with the FC-NVMe transport and transports the requests
(FC-NVMe FC link services and FC-NVMe commands IUs) to the fabric. It
also provides the support for allocating h/w queues and aborting FC-NVMe
FC requests.

Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add FC-NVMe port discovery and PRLI handling

Added logic to change the login process into an optional PRIL step for
FC-NVMe ports as a separate operation, such that we can change type to
0x28 (NVMe).

Currently, the driver performs the PLOGI/PRLI together as one operation,
but if the discovered port is an NVMe port then we first issue the PLOGI
and then we issue the PRLI. Also, the fabric discovery logic was changed
to mark each discovered FC NVMe port, so that we can register them with
the FC-NVMe transport later.

Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add debug knob for user control workload

For Target mode, user can control the work load by placing qla2xxx's irq
vector on certain CPU via the smp_affinity knob. This patch allows user
to control the number of QPair's irq to be active. The irqs are
allocated at driver load time until unload. The work itself is placed on
the QPair based on user setting.

Usage:
modprobe qla2xxx qlini_mode=disabled ql2xuctrlirq=1
mount -t debugfs none /sys/kernel/debug
echo 2 > /sys/kernel/debug/qla2xxx/qla2xxx_[host num]/naqp
echo [cpu id] > /proc/irq/[irq id]/smp_affinity_list

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Preparation for Target MQ.

In Current code, Req Q 0, RespQ 0 & hardware_lock are the main resources
for sending and process completion of Target IO. These resources are now
referenced behind a new qpair/"struct qla_qpair base_qpair". Main path
IO handle will access those resources via the qpair pointer in
preparation for Target MQ.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Combine Active command arrays.

Merge active/outstanding cmd arrays from target side and initiator side
together in prepration for Target Multi Queue support.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ql2xiniexchg parameter

Previously, the ql2xexchoffld module parameter was used to control the
max number of exchanges to be offload onto host memory.

Module parameter ql_dm_tgt_ex_pct was used to control the percentage of
exchanges allocated to the Target side.

With this patch, module parameter ql_dm_tgt_ex_pct is no longer used to
control exchanges for the driver. New module parameter ql2xiniexchg is
added to control exchanges between target mode and initiator mode.

With the updated module parameters, users can control the exact number
of exchanges for either Initiator or Target. The exchange offload
feature will be automatically enabled when the total number of exchanges
exceeds 2048 limit.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Change scsi host lookup method.

For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Use IOCB interface to submit non-critical MBX.

The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.

Following commands are being routed through IOCB interface

- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Improve T10-DIF/PI handling in driver.

Add routines to support T10 DIF tag.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Simplify usage of SRB structure in driver

This patch simplifies SRB structure usage in driver.

- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Improve RSCN handling in driver

Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.

Some of the other improvements are as follows

- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Add framework for async fabric discovery

Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.

This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.

Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.

This patch adds following capabilities in the driver

- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

scsi: qla2xxx: Add multiple queue pair functionality.

Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.

Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.

Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: change FC drivers to use 'struct bsg_job'

Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Add bsg interface to support D_Port Diagnostics.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Properly reset firmware statistics.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Add support for online flash update for ISP27XX.

Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Allow fw to hold status before sending ABTS response.

Set bit 12 of additional firmware options 3 to let firmware
hold status IOCB until ABTS response is received from Target.

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Move atioq to a different lock to reduce lock contention

99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Added interface to send explicit LOGO.

This patch adds interface to send explicit LOGO
explicit LOGO using using ELS commands from driver.

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Add FW resource count in DebugFS.

DebugFS now will show fw_resource_count node.

FW Resource count

Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Enable Exchange offload support.

This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: Enable Extended Logins support

This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

qla2xxx: remove redundant declaration in 'qla_gbl.h'

Remove 2 redundant extern inline functions: qla8044_set_qsnt_ready() and
qla8044_need_reset_handler(). At present, within upstream next kernel
source code, they are only used within "drivers/scsi/qla2xxx/qla_nx2.c".

The related error and warnings (with allmodconfig under tile):

CC [M] drivers/scsi/qla2xxx/qla_nx2.o
drivers/scsi/qla2xxx/qla_nx2.c:1633:1: error: static declaration of 'qla8044_need_reset_handler' follows non-static declaration
qla8044_need_reset_handler(struct scsi_qla_host *vha)
^
In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
from drivers/scsi/qla2xxx/qla_nx2.c:11:
drivers/scsi/qla2xxx/qla_gbl.h:756:20: note: previous declaration of 'qla8044_need_reset_handler' was here
extern inline void qla8044_need_reset_handler(struct scsi_qla_host *vha);
^
drivers/scsi/qla2xxx/qla_gbl.h:756:20: warning: inline function 'qla8044_need_reset_handler' declared but never defined
make[3]: *** [drivers/scsi/qla2xxx/qla_nx2.o] Error 1
make[2]: *** [drivers/scsi/qla2xxx] Error 2
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2

CC [M] drivers/scsi/qla2xxx/qla_tmpl.o
In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
from drivers/scsi/qla2xxx/qla_tmpl.c:7:
drivers/scsi/qla2xxx/qla_gbl.h:755:20: warning: inline function 'qla8044_set_qsnt_ready' declared but never defined
extern inline void qla8044_set_qsnt_ready(struct scsi_qla_host *vha);
^

Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Handle chip reset in target mode.

A chip reset can occur after driver submits command to the stack. Abort
command processing if a chip reset has occurred or in progress when you
get a follow up for a command.

Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Add Host reset handling in target mode.

Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Add FDMI-2 functionality.

Add support for the FDMI-2 fabric switch feature.

Since FDMI-2 uses code from FDMI-1, some of the existing code
needed to be repaired to prevent fields from being overflowed.

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Collect PCI register checks and board_disable scheduling

Add an uint16_t variant of qla2x00_check_reg_for_disconnect and use
these routines to check and schedule a PCI-disconnected board from a
centralized place.

Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

scsi: use 64-bit value for 'max_luns'

Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

scsi: use 64-bit LUNs

The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.

So update the linux SCSI stack to use 64-bit LUN numbers.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: T10-Dif: add T10-PI support

Add support for T10-Dif for Target Mode to qla driver.
The driver will look for firmware attribute that support
this feature. When the feature is present, the capabilities
will be report to TCM layer.

Add CTIO CRC2 iocb to build T10-Dif commands.
Add support routines to process good & error cases.

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Change copyright year to 2014 in all the source files.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

qla2xxx: Add ISP8044 serdes bsg interface.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

[SCSI] qla2xxx: Add IOCB Abort command asynchronous handling.

Send aborts to the firmware via the request/response queue mechanism.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Read capture firmware dump on mailbox timeout for ISP8044 and ISP82XX.

Allow for the capture of a firmware dump but have a sysfs node
(allow_cna_fw_dump) to allow the feature to be enabled/disabled dynamically.

The default is off.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add support for ISP2071.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix warning reported by smatch.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add BSG interface for read/write serdes register.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Disable adapter when we encounter a PCI disconnect.

If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Refactor shutdown code so some functionality can be reused.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Revert "qla2xxx: Ramp down queue depth for attached SCSI devices when driver resources are low."

This reverts commit 3c290d0b5f8ff7b0fd2c964c5ec2c14191a9e790

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Notify ISPFX00 firmware when driver is unloaded or system is shut down.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Acked-by: Srinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Reconfigure thermal temperature.

For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add setting of driver version string for vendor application.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add ISPFX00 specific bus reset routine.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add support for ISP8044.

[jejb: checkpatch fixes]
Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix sparse warning from qla_mr.c and qla_iocb.c.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Enhancements to support ISPFx00.

[jejb: fix up checkpatch issues]
Signed-off-by: Andrew Vazquez <andrew.vasquez@qlogic.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Revert "qla2xxx: Add setting of driver version string for vendor application."

The original patch was not covering all the adapters and firmwares.

This commit reverts 3a11711ad00caebee07e262d188cea66f3473c38.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Integrate generic card temperature with mezz card temperature.

Give priority to I2C thermal.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Don't process RSCNs for a vport on the same physical adapter.

Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.

Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add setting of driver version string for vendor application.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Update the copyright information.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Do link initialization on get loop id failure.

To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Ramp down queue depth for attached SCSI devices when driver resources are low.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Determine the number of outstanding commands based on available resources.

Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Parameterize the link speed of hba rather than fcport.

Parameterize qla2x00_get_link_speed_str() to be generic on link speed.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix for warnings reported by sparse.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Wrong PCIe(2.5Gb/s x8) speed in the kerenel message for ISP82xx.

qla2xxx show wrong PCIe(2.5Gb/s x8) speed in the kerenel message. It should be
5.0Gb/s.

Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Update the driver copyright.

Update the driver copyright from 2003-2011 to 2003-2012.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Changes for ISP83xx loopback support.

Minor changes to support loopback functionality with ISP83xx CNAs.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Implemetation of mctp.

[jejb: fix up checkpatch errors]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: IDC implementation for ISP83xx.

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Implementation of bidirectional.

[jejb: merge fix for introduced warning]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series

Add LLD target mode for >= 24xx series HW. This code was originally based on
external qla2x00t module based on 8.02.01-k4, and has been refactored to
push the bulk of code into mainline qla2xxx.ko LLD -> qla_target.c.

The implementation uses internal workqueues for I/O context submission
into tcm_qla2xxx code, and includes the struct qla_tgt_func_tmpl API for
external interaction to allow qla2xxx LDD to function without direct
target-core dependencies:

It also enables qla_target.c usage within existing qla2xxx LLD code.
This includes:

*) Addition of target mode specific members to existing data
structures in qla_def.h and struct qla_hw_data->tgt_ops using
qla_target.h:struct qla_tgt_func_tmpl

*) Addition of struct qla_tgt_func_tmpl and direct calls into
qla_target.c logic w/ qlt_* prefixed functions.

*) Addition of qla_iocb.c:qla2x00_req_pkt() for ring processing, and
qla2x00_issue_marker() for handling request/response queue processing
for target mode operation

*) Addition of various qla_tgt_mode_enabled() logic checks in
qla24xx_nvram_config(), qla2x00_initialize_adapter(), qla2x00_rff_id(),
qla2x00_abort_isp(), qla24xx_modify_vp_config(), and
qla2x00_vp_abort_isp().

By default the new qlini_mode module parameter is setting initiator-mode
to 'enabled' in order for 'modprobe qla2xxx' to continue to function as
expected in initiator only mode. Enabling target-mode operation will
currently require a:

modprobe qla2xxx qlini_mode="disabled"

in order to explictly disabled initiator mode and allow target-mode
to be enabled via tcm_qla2xxx configfs fabric callers.

(nab: Convert to qlini_mode='enabled' by default in qla_target.c)
(joern: Remove loop_id from qla_tgt_make_local_sess() arguments +
Remove unused s_id + fix s_id endianness bug +
simplify qla_tgt_abort_work)
(gerard: fix section __exit mismatch in qla_tgt_exit)
(arun: Capture ATIO queue during firmware dump + Send SCR in target mode +
Target mode review comments)
(roland: Don't create duplicate target sessions to address tearing down
ACLs with IO in flight + Add missing call to qlt_fc_port_deleted
call during qla2x00_schedule_rport_del timeout)

Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Log link up and link down messages to track link flops.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Perform implicit logout during rport tear-down.

During rport tear-down, make sure we do an implicit LOGO of the fcport in our
firmware to try to clear any residual commands associated with that fcport.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Consolidation of SRB processing.

Rework the structures related to SRB processing to minimize the memory
allocations per I/O and manage resources associated with and completions
from common routines.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Enhancements to support ISP83xx.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Nigel Kirkland <nigel.kirkland@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Consolidated IOCB processing routines.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Encapsulate prematurely completing mailbox commands during ISP82xx firmware hang.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Issue mailbox command only when firmware hung bit is reset for ISP82xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Implemeted beacon on/off for ISP82XX.

[jejb: fix up checkpatch.pl errors]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add support for ISP82xx to capture dump (minidump) on failure.

Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.

[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Code changes to support new dynamic logging infrastructure.

The code is changed to support the new dynamic logging infrastructure.
Following are the levels added.
Default is 0 - no logging. 0x40000000 - Module Init & Probe.
0x20000000 - Mailbox Cmnds. 0x10000000 - Device Discovery.
0x08000000 - IO tracing. 0x04000000 - DPC Thread.
0x02000000 - Async events. 0x01000000 - Timer routines.
0x00800000 - User space. 0x00400000 - Task Management.
0x00200000 - AER/EEH. 0x00100000 - Multi Q.
0x00080000 - P3P Specific. 0x00040000 - Virtual Port.
0x00020000 - Buffer Dump. 0x00010000 - Misc.
0x7fffffff - For enabling all logs, can be too many logs.

Setting ql2xextended_error_logging module parameter to any of the above
value, will enable the debug for that particular level.
Do LOGICAL OR of the value to enable more than one level.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Basic infrastructure for dynamic logging.

This patch adds the dynamic logging framework to the qla2xxx driver.
The user will be able to change the logging levels on the fly i.e.
without load/unload of the driver. This also enables logging to be
enabled for a particular section of the driver such as initialization,
device discovery etc.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.

Make the read/write sfp mailbox command routines uniform, and remove redundancy.
Also protect against attempting to do a single byte dma in these routines.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Allow an override of the registered maximum LUN.

The 'max_lun' value registered for each scsi_host is currently
capped at 0xffff. The new module parameter can allow for
2nd-level flat-space addressing method-infrastructure to be
supported.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.

Encapsulate the unlocking of the ROM lock in a function for better
code readability.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add the ql2xdontresethba module_param.

Also, change the ISP82xx code to only reset if this module_param is set
and reset is intended via the QLA82XX_DEV_NEED_RESET case.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add test for valid loop id to qla2x00_relogin().

If fabric device has invalid loop id (FC_NO_LOOP_ID) then call
qla2x00_find_new_loop_id() to attempt to obtain valid loop id.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update copyright banner.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Abort pending commands for faster recovery during ISP reset.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Remove code to not reset ISP82xx on failure.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add sysfs node for displaying board temperature.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update FCP priority information to firmware before sending IOs

The FCP priority info was not being updated properly in certain situations.
Here are the changes that needs to be done to take care of this issue:
1. No need to check fcport->state for FCS_UNCONFIGURED in
qla24xx_update_fcport_fcp_prio(), since an invalid loop id check is
already performed which is sufficient.
2. Add the missing qla24xx_update_fcport_fcp_prio() function call
within qla2x00_update_fcport() function, so that the priority info
is updated on every port addition or change.
3. Perform proper adapter types checking.
4. Other changes, associated with DEBUG/printk's and parameter passing.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Added support for quiescence mode for ISP82xx.

Support is added for quiescence mode. This feature is for P3P
adapters. Any of the functions can put the firmware into quiescence
state. All the others have to ack that request. During quiescence mode
current commands are processed and all the new incoming I/Os are
blocked. Loop resync is performed after firmware comes out of
quiescence state.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add module parameter to enable/disable GFF_ID device type check.

Add the module parameter ql2xgffidenable to disable/enable the use of the
GFF_ID name server command to prevent non FCP SCSI devices from being added to
the driver's internal fc_port database.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Handle MPI timeout indicated by AE8002

In case the MPI times out, the FW issues an async event AE8002
to indicate this to every FCoE function. The FC/FCoE driver is
required to handle this, by doing a soft reset and issuing a
Write MPI register mailbox command to reset the MPI.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Cleanup some dead-code and make some functions static.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Added AER support for ISP82xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Cleanup some dead-code and make some functions static.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update copyright banner.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Rearranged and cleaned up the code for processing the pending commands.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Updates for ISP82xx.

Re-organized and cleaned up the ISP82xx specific code.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add qla2x00_free_fcports() function

This function was added to encapsulate freeing the memory for all the fcports
associated with a particular vha. Also added a call to qla2x00_free_fcports()
to qla2x00_free_device() to free the memory for all the fcports associated with
a vha during device removal.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports

The default method that qla2xxx uses is the GID_PT nameserver command to
get a list of Nx_Ports. This patch adds a GFF_ID call for each port
returned by GID_PT to get the FC4 type. If the FC4 type is not FCP SCSI
then the qla2xxx driver will not record that port in it's port database.
For switches that do not support the GFF_ID command, the behavior will be
for qla2xxx to store that port anyways.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Removed dependency for SRB structure for Marker processing

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add internal loopback support for ISP81xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Clear drive active CRB register when not in use.

The CRB drive active register is cleared when driver is unloaded
or when driver enters failed state.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Optionally disable target reset.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: T10 DIF support added.

Signed-off-by: Duane Grigsby <duane.grigsby@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Support for asynchronous TM and Marker IOCBs.

Currently we can only issue the task management (TM)
commands via the mailbox mechanism. This is a limitation,
since only one mailbox command can be issued at a time.
The purpose of this effort is to provide support for
issuing and processing the respose to TM and Marker
IOCBs asynchronously. Towards achieving this, the
consolidated srb architecture that is currently used for
BSG and IOCB/Logio commands has been enhanced and used.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Provide common framework for BSG and IOCB commands.

Currently, BSG and IOCB/Logio commands have a different
framework (srb structs). The purpose of this effort is to
consolidate them into a generalized framework for these
as well as other asynchronous operations in the future.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Limit mailbox command contention for ADISC requests.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add ISP82XX support.

Enhanced the driver to support new FCoE host bus adapter.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add APEX support.

Allows priority setting for FCP_CMNDs.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Re-organized BSG interface specific code.

1. Segregate BSG interface specific code to new files.
2. Handle multiple vendor specific commands indepedently.
3. Reorganised support for reset, management and update FCoE firmware commands.
4. Fixed memory leak issue in Loopback.
5. Added new vendor command to support iiDMA using BSG interface.
6. Proper cleanup of dma mapped and dma allocated buffers for BSG request.

[jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add firmware ETS burst support.

Can be used to balance NIC/FCoE traffic distribution.

Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Correct use-after-free issue in terminate_rport_io callback.

The explicit logout (LOGO) issued at the end of the callback will
flush (via normal scsi_cmnd->done()) any outstanding commands
(FCP2) the firmware is holding. While iterating through the
outstanding_cmnd array in qla2x00_abort_fcport_cmds(), locking
and unlocking of the hardware spinlock, opens-up the driver to
cases where the processed SRB (sp) could be used after the
command completed from interrupt context.

Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Obtain proper host structure during response-queue processing.

Original code incorrectly assumed only status-type-0
IOCBs would be queued to the response-queue, and thus all
entries would safely reference a VHA from the IOCB
'handle.'

Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add BSG support for FC ELS/CT passthrough and vendor commands.

[jejb: fixed printk casting issues]
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Get the link data rate explicitly during device resync.

When the hba port gets logged out of the fabric, or other
such transitional state when the physical link is still present,
the driver doesn't receive a loop up asyn event (where the link
data rate currently gets set). Hence send a explicit mailbox command
to get the link rate in such conditions.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Queue depth ramp up/down modification changes.

Removed the module parameters ql2xqfulltracking and ql2xqfullrampup
since the queue depth ramp up/down functionality is moved to scsi-ml.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Retrieve firmware's maximum number of supported FCFs.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add firmware-dump kobject uevent notification.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add asynchronous-login support.

ISPs which support this feature include 23xx and above.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Synchronize MPI settings after a PE Reset.

Ensure MPS remains in synchronization across all NIC/FCoE
functions after a reset.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Check status of qla2x00_get_fw_version() call.

Unlike earlier ISPs, recent ISPs (ISP81xx) can in fact fail this
mailbox command.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Export TLV data on supported ISPs.

Firmware currently provides PB and PGF TLVs.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Export XGMAC statistics on supported ISPs.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add an override option to specify ISP firmware load semantics.

As it may be useful during debugging to use a specific firmware
image.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Conditionally disable automatic queue full tracking.

Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.

The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.

This patch implements an "off switch" as a module parameter.

Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add QoS support.

Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add EDC-update support.

Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add reset capabilities for application support.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct ISP abort semantics for NVRAM, VPD, and flash update.

Ensure that an ISP-abort has completed before performing any
update. After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset. This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add Flash-Access-Control support for recent ISPs.

Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.

Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Update MPI/PHY version retrieval codes.

Reflects layout and format of latest specification.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Consolidate queuecommand implementations.

Post refactoring/multi-queue additions essentially eliminated the
need for separate ISP24XX+ queuecommand as isp_ops contains a
function pointer to the associated 'start_scsi()' operation.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Properly acknowledge IDC notification messages.

To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Remove interrupt request bit check in the response processing path in multiq mode.

Correct response-queue-0 processing by instructing the firmware
to run with interrupt-handshaking disabled, similarly to what is
now done for all non-0 response queues. Since all
response-queues now run in the same mode, the driver no longer
needs the hot-path 'is-disabled-HCCR' test.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Modify firmware-load order precedence for ISP81XX parts.

Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add ISP81XX support.

Codes to support new FCoE boards.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.

Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: changes in multiq code

Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: add support for multi-queue adapter

Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.

[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Refactor qla data structures

Following changes have been made to the qla2xxx FC driver in
preparation for the multi- queue and future SR IOV hardware.

1. scsi_qla_host structure has been changed to contain scsi host
specific data only.

2. A new structure, qla_hw_data is created to contain HBA specific
hardware data.

3. Request and response IO specific data strucures are created.

4. The global list of fcports for the hba is not maintained anymore,
instead a fcport list is construted on per scsi_qla_host.

Signed-of-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add NPIV-Config Table support.

To instatiate pre-configured vport entities defined within an
HBA's flash memory.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add Flash Layout Table support.

The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Retrieve board serial-number and description from VPD.

Recent ISPs have this information written at manufacturing time,
so use the information. This also reduces future churn of the
qla_devtbl.h file contents, as the driver can now depend on the
information to be present in VPD.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Allow the user the option of disabling iIDMA.

iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities). It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT). So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Cleanup NPIV related functions

Removed repeated or unnecessary operations during vport
creation/deletion.

Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add dev_loss_tmo_callbk/terminate_rport_io callback support.

Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Extend the 'fw_dump' SYSFS node the ability to initiate a firmware dump.

The user-initiated dump can be a useful tool in triaging complex
ISP and FC issues.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: make qla2x00_issue_iocb_timeout() static

This patch makes the needlessly global qla2x00_issue_iocb_timeout()
static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

SCSI: convert struct class_device to struct device

It's big, but there doesn't seem to be a way to split it up smaller...

Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[SCSI] qla2xxx: Add ISP84XX support.

Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add midlayer target/device reset support.

Now that infrastructure is present within the midlayer and there
is a clear distinction between what is expected from a device and
target reset, convert the current device-reset codes to a
target-reset, and add codes to perform a proper device-reset (LUN
reset).

In the process of adding reset support, collapse and consolidate
large sections of mailbox-command (TMF issuance) codes,
generalize the two 'wait-for-commands-to-complete' functions, and
add a generic-reset routine for use by midlayer reset functions.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add Flash Descriptor Table layout support.

The Flash Descriptor Table (FDT) present on many recent HBAs
encodes flash accessing characteristics of the flash-part used on
the HBA. Use this information during flash manipulation (writes)
rather than using specific hard-coded values based on queried
manufacturer and device IDs.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Cruft cleanup of functions and structures.

Strip unused (DEBUG-ONLY) enabled functions, inlines, useless
wrappers, and unused DPC flags from the code. Another step in
the migration towards a cleaner (less-crusty) driver.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add hardware trace-logging support.

Recent ISPs have a region within FLASH which acts as a repository
for the logging of serious hardware and software failures.
Currently, the region is large enough to support up to 255
entries.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add FC-transport Asynchronous Event Notification support.

Supported events include LIP, LIP reset, RSCN, link up, and link
down.

To support AEN (and additional forthcoming features), we also
introduce a simple deferred-work construct to manage events which
require a non-atomic sleeping-capable context. This work-list is
processed as part of the driver's standard DPC routine.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Remove unused and obsolete #define's.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Update copyright banner.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Cleanup any outstanding SRB resources during shutdown.

Refactor SRB-failure completion codes in the process. Also,
signal the DPC routine to complete sooner as backend processing
at shutdown-time is superflous.

[jejb: resolve conflicts with pci_enable_device_bars removal]

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add Fibre Channel Event (FCE) tracing support.

FCE support enables the firmware to record FC extended link
services and basic link services frames which have been
transmitted and received by the ISP. This allows for a limited
view of the FC traffic through the ISP without using a FC
analyzer. This can be useful in situations where a physical
connection to the FC bus is not possible.

The driver exports this information in two ways -- first, via a
debugfs node exported for all supported ISPs under:

<debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce

where a read of the 'fce' file will provide a snapshot of the
firmware's FCE buffer; and finally, the FCE buffer will be
extracted during a firmware-dump scenario.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Trace-Control naming cleanups.

In preparation for FCE (Fibre Channel Event) tracing support.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Code cleanups.

- make the following needlessly global code static:
- qla_attr.c: qla24xx_vport_delete()
- qla_attr.c: qla24xx_vport_disable()
- qla_mid.c: qla24xx_allocate_vp_id()
- qla_mid.c: qla24xx_find_vhost_by_name()
- qla_mid.c: qla2x00_do_dpc_vp()
- qla_os.c: struct qla2x00_driver_template
- qla_os.c: qla2x00_stop_timer()
- qla_os.c: qla2x00_mem_alloc()
- qla_os.c: qla2x00_mem_free()
- qla_sup.c: qla2x00_lock_nvram_access()
- qla_sup.c: qla2x00_unlock_nvram_access()
- qla_sup.c: qla2x00_get_nvram_word()
- qla_sup.c: qla2x00_write_nvram_word()
- #if 0 the following unused global functions:
- qla_mbx.c: qla2x00_system_error()
- qla_os.c: remove some unneeded function prototypes
- removed unused functions:
- qla_dbg.c: qla2x00_dump_pkt()
- qla_mbx.c: qla2x00_get_serdes_params()
- qla_mbx.c: qla2x00_get_idma_speed()
- qla_mbx.c: qla24xx_get_vp_database()
- qla_mbx.c: qla24xx_get_vp_entry()

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Small modifications and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Use completion routines.

Instead of abusing the semaphore interfaces for mailbox command
completions.

Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Don't schedule the DPC routine to perform an issue-lip request.

As the driver depends on the DPC routine to handle bottom-half
loop resynchronization in order to recover from the issue-lip
request. The issue_lip call is sleeping context capable, so just
issue the reset function there.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Retrieve additional HBA port statistics from recent ISPs.

HBAs supporting these additional counters include ISP24xx and
ISP25xx type boards.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Retrieve max-NPIV support capabilities from FW.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add flash burst-read/write support.

Newer ISPs support a mechanism to read and write flash-memory via
the firmware LOAD/DUMP memory mailbox command routines. When
supported, utilizing these mechanisms significantly reduces
overall access times.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add ISP25XX support.

Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: add support for NPIV

Following patch adds support for NPIV (N-Port ID Virtualization) to the
qla2xxx.

- supported within switched-fabric topologies only.
- supports up to 63 virtual ports on each physical port.

Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Export OptionROM boot-codes version information.

This includes BIOS, EFI, FCODE and firmware versions.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add MSI-X support.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: make qla2x00_reg_remote_port() static

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Correct QUEUE_FULL handling.

- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Workaround D3 power-management issues.

Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.

In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] Maintain module-parameter name consistency with qla2xxx/qla4xxx.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[PATCH] fix qla{2,4} build error

commit 0181944fe647cae18d545ac1167df3d15d393701 adds a
'extended_error_logging' global variable to qla2xxx which is defined by
qla4xxx too.

Trying to build both drivers results in the following error:

LD drivers/scsi/built-in.o
drivers/scsi/qla4xxx/built-in.o: In function `qla4xxx_slave_configure':
drivers/scsi/qla4xxx/ql4_os.c:1433: multiple definition of `extended_error_logging'
drivers/scsi/qla2xxx/built-in.o:drivers/scsi/qla2xxx/qla_os.c:2166:
first defined here
make[2]: *** [drivers/scsi/built-in.o] Error 1
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2

The following patch simply adds a qla2_ (qla4_ respectively) prefix to
the variable name.

Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

IRQ: Maintain regs pointer globally rather than passing to IRQ handlers

Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.

(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.

(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)

[SCSI] qla2xxx: Add support for symbolic nodename FC transport attribute.

Refactored original code from qla_gs.c:qla2x00_rsnn_nn().

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add iIDMA support.

iIDMA (Intelligent Interleaved Direct Memory Access) allows for
the HBA hardware to send FC frames at the rate at which they can
be received by a target device. By taking advantage of the
higher link rate, the HBA can maximize bandwidth utilization in a
heterogeneous multi-speed SAN.

Within a fabric topology, port speed detection is done via a Name
Server command (GFPN_ID) followed by a Fabric Management command
(GPSC). In an FCAL/N2N topology, port speed is based on the HBA
link-rate.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: make some more functions static

Make some needlessly global functions static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add support for extended error logging.

Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Remove no-op IOCTL codes and macros.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add DMI (Diagnostics Monitoring Interface) support.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Rework firmware-trace facilities.

- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Remove obsolete firmware-loader-module support.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Remove unused port-type RSCN handling code.

Expandind on the previous commit:

commit 79f89a4296ff22f09baf538d4ff2a6d0c3097a73
Author: andrew.vasquez@qlogic.com <andrew.vasquez@qlogic.com>
Date: Fri Jan 13 17:05:58 2006 -0800

[SCSI] qla2xxx: Disable port-type RSCN handling via driver state-machine.

and given:

- the process-context requirements of the FC transport
rport-APIs.
- lack of port-type RSCN processing logic for ISP24xx and newer
chips.

it's time now to remove the state-machine logic from mainline.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Drop unused driver cruft.

- structure definitions.
- structure members.
- #define's.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Correct FCAL login retry logic for ISP24xx.

ISP24XX FW does not support Mbx 0x74 ie Login Local Port.
Added the equivalent code for ISP24XX ie to relogin in non
fabric case for ISP24XX use login iocb.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: use kthread_ API

Use the kthread_ API instead of opencoding lots of hairy code for kernel
thread creation and teardown.

Also switch from semaphore-based thread wakeup to wake_up_process.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-By: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add support to retrieve/update HBA option-rom.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add beacon support via class-device attribute.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Add host-statistics FC transport attributes.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Correct issue where the rport's upcall was not being made after relogin.

A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>