scsi: pm80xx: Set RETFIS when requested by libsas

By default PM80xx HBAs return FIS only when a drive reports an error.
The RETFIS bit forces the controller to populate FIS even when a drive
reports no error.

Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20230819213040.1101044-3-ipylypiv@google.com
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Use libsas internal abort support

New special handling is added for SAS_PROTOCOL_INTERNAL_ABORT proto so that
we may use the common queue command API.

Link: https://lore.kernel.org/r/1647001432-239276-4-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Handle non-fatal errors

Firmware expects host driver to clear scratchpad rsvd 0 register after
non-fatal error is found.

This is done when firmware raises fatal error interrupt and indicates
non-fatal error. At this point firmware updates scratchpad rsvd 0 register
with non-fatal error value. Here host has to clear the register after
reading it during non-fatal errors.

Rename:

- MSGU_HOST_SCRATCH_PAD_6 to MSGU_SCRATCH_PAD_RSVD_0

- MSGU_HOST_SCRATCH_PAD_7 to MSGU_SCRATCH_PAD_RSVD_1

Link: https://lore.kernel.org/r/20220222092618.108198-1-Ajish.Koshy@microchip.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Fix use of struct set_phy_profile_req fields

In mpi_set_phy_profile_req() and pm8001_set_phy_profile_single(), use
cpu_to_le32() to initialize the ppc_phyid field of struct
set_phy_profile_req. Furthermore, fix the definition of the reserved field
of this structure to be an array of __le32, to match the use of
cpu_to_le32() when assigning values. These changes remove several sparse
type warnings.

Link: https://lore.kernel.org/r/20220220031810.738362-13-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Fix bogus FW crash for maxcpus=1

According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.

However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.

Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.

The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.

Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Completing pending I/O after fatal error

When controller runs into fatal error, I/Os get stuck with no response,
handler event is defined to complete the pending I/Os (SAS task and
internal task) and also perform the cleanup for the drives.

Link: https://lore.kernel.org/r/20210415103352.3580-7-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Check for fatal error

When the controller runs into a fatal error, commands get stuck due to no
response. If the controller is in fatal error state, abort requests issued
to the controller get stuck too.

Check the controller state for fatal error conditions.

Link: https://lore.kernel.org/r/20210109123849.17098-3-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Do not busy wait in MPI init check

We do not need to busy wait during mpi_init_check() since it is not being
invoked in atomic context. mpi_init_check() is being called from
pm8001_pci_resume(), pm8001_pci_probe(). Hence we are replacing udelay with
msleep.

Link: https://lore.kernel.org/r/20210109123849.17098-2-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Avoid busywait in FW ready check

In function check_fw_ready() we busy wait using udelay. The CPU is not
released and we see need_resched failures.

Busy waiting is not necessary since we are in process context and we can
sleep instead. Replace udelay with msleep of 20 ms intervals while waiting
for firmware to become ready.

It has been verified that check_fw_ready is not being used in interrupt
context anywhere, hence it is safe to make this change.

Link: https://lore.kernel.org/r/20201102165528.26510-4-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Increase timeout for pm80xx mpi_uninit_check

The function mpi_uninit_check takes longer for inbound doorbell register to
be cleared. Increased the timeout substantially so that the driver does not
fail to load.

Link: https://lore.kernel.org/r/20191114100910.6153-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: ianyar <ianyar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Fixed kernel panic during error recovery for SATA drive

Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.

Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Fixed system hang issue during kexec boot

When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.

Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Fix for phy enable/disable functionality

Added proper mask for phy id in mpi_phy_stop_resp().

Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: corrected linkrate value.

Corrected the value defined for LINKRATE_60 (6 Gig).

Signed-off-by: Raj Dinesh <Raj.Dinesh@microsemi.com>
Signed-off-by: Viswas G <viswas.g@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: ILA and inactive firmware version through sysfs

Added support to read ILA version and inactive firmware version from MPI
configuration table and export through sysfs.

Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: redefine sas_identify_frame structure

sas_identify structure defined by pm80xx doesn't have CRC field. So
added a new sas_identify structure without CRC.

Signed-off-by: Raj Dinesh <Raj.Dinesh@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: Handling Invalid SSP Response frame

The request has to be retried incase if the length of the SSP
Response IU is invalid.

Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

pm80xx: Update For Thermal Page Code

Thermal page code has been changed to 7 for the 12G controllers.

Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

[SCSI] pm80xx: Resetting the phy state.

Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.

Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] pm80xx: Firmware logging support.

Supports below logging facilities,
Inbound outbound queues dump.
Non fatal dump in case of IO failures.
Fatal dump in case of firmware failure.

[jejb: checkpatch spacing fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] pm80xx: Phy settings support for motherboard controller.

Phy profile implementation to support phy settings feature
for motherboard controllers.

[jejb: checkpatch fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] pm80xx: Device id changes to support series 8 controllers.

Updated pci id table with device, vendor, subdevice and subvendor ids
for 8074, 8076, 8077 SAS/SATA 12G controllers. Added 12G related macros.

Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] pm80xx: thermal, sas controller config and error handling update

Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants

[jejb: fix up tabs and spaces issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] pm80xx: NCQ error handling changes

Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.

[jejb: fix checkpatch issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files

Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.

Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>